Search Documents

By Karen Munro

Importance of Aquatic Studies for Mining ?Aquatic habitat is usually the first area where a mine interacts with the ?real world? outside the mine footprint ?Water management is a key consideration for a mine?Effects on the aquatic environment often extend to wildlife and human uses ?There is a lot of regulatory focus on issues of water quality, fish and fish habitat

May 1, 2011

By Rénard Chaigneau

Quality during induration Drying ??40% of energy ??Drying velocity = f(1/radius2) ??Size versus risk of condensation ??Flow is important (minimise fines)Oxidation ??IOC Fe2+ typically 0.04% ??Important to minimise Fe2+forLow Temperature Disintegration ??Tight size distribution is key13

May 1, 2011

By S. Kelebek, B. Ingram, C. Gibson, T. MacNeil, M. Aghamirian

"The beneficiation and upgrading of pyrochlore from its ores is carried out through flotation. In industrial practice, upgrading is conducted in a two-stage flotation process in which pyrochlore flotation is carried out after gangue mineral pre-flotation (carbonate, silicate, sulphide or phosphate reverse flotation). In this study, the flotation of pyrochlore from a low grade carbonatite ore was performed at the laboratory scale following a two-stage flotation process in which carbonate minerals were floated in advance of niobium minerals. In parallel, a simplified flotation process was developed in which pyrochlore was floated directly from gangue minerals at increasingly acidic pH. Laboratory results indicated that both two-stage and direct flotation provided similar results in terms of niobium grade-recovery. Based on these results, a large scale, integrated pilot plant was conducted using a direct flotation flowsheet. While the elimination of reverse gangue flotation resulted in flowsheet simplification, the dissolution of carbonate minerals and the subsequent effect of dissolved cations on the floatability of pyrochlore added an element of complexity. A comparison of results from locked-cycle laboratory testing and pilot plant testing highlights the challenges of scaling up a complex flowsheet. A case is made for the direct flotation process and the key parameters to achieving success in large scale direct flotation of pyrochlore are discussed.INTRODUCTIONPyrochlore (Ca,Na)2Nb2O6(OH,F) is a niobium bearing mineral which has been the primary global source of niobium since the first pyrochlore mine commenced operations in the late 1960s (Gibson et al., 2015a). Preceding the discovery and development of high grade pyrochlore deposits in North and South America, the majority of global niobium supply came from gravity concentration operations of columbite (Fe,Mn)Nb2O6, across Africa (Perrault and Manker, 1981)."

Jan 1, 2016

By Y. Okita

The Goro Nickel Process, developed over a ten-year period, uses a number of novel processing steps and treats two ore types, limonite and saprolite, together. Nickel and cobalt are solubilized using a 270°C pressure acid leach in sulphuric acid, which rejects the bulk of the Fe into the leach residue as hematite particles. The leach liquor, after CCD, is aerated to oxidize any ferrous iron to the ferric form and is neutralized with limestone to precipitate iron as hydroxides together with gypsum from the neutralization of the free acid. Further neutralization with lime, together with steps to remove suspended solids, reduces the iron to trace concentrations. Nickel and cobalt are directly recovered from the low-iron leach solution by primary solvent extraction using Cyanex 301® (SXl) in a high-strength hydrochloric acid solution. Nickel is subsequently separated from cobalt in a secondary solvent extraction circuit using tri-isooctylamine. A granular nickel oxide is made by pyrohydrolysis, and this allows the recycling of hydrochloric acid to SXl. The process is currently being commercialized to produce approximately 60,000 t/y of nickel as nickel oxide granules and approximately 5,400 t/y of cobalt as cobalt carbonate. This paper describes the process development to control the Fe concentration in the SX1 feed solution.

Jan 1, 2006

By K. G. Baxter, D. G. Dixon

The Sepon process plant utilises an autoclave to oxidize a flotation concentrate containing pyrite, residual copper minerals, and sulphur. The concentrate is produced from the residue of a preceding atmospheric copper leaching circuit. The function of the autoclave is to provide iron and acid for that atmospheric copper leaching circuit. The key issues in the operation of the autoclave are to maximise the production of acid and ferric ions and to avoid scaling issues related to sulphur balling in the autoclave. Scale control in the autoclave was examined using various dispersants and residue recycle without success. Operation of the autoclave at high temperature and high acidity addressed the scale issue through rapid oxidation of the sulphur and produced a ferric sulphate precipitate in the residue that could be re-leached to provide ferric iron. This paper presents the development steps followed, through batch and continuous piloting that resulted in an autoclave circuit design that addressed the above process requirements. Following definition of the process design basis, modelling of the autoclave operation was carried out to assist with engineering design. The model included thermodynamics and kinetics of oxidation of pyrite, elemental sulphur and covellite and also considered gas/liquid mixing, oxygen solubility as a function of temperature and solution composition, ferrous to ferric oxidation, gangue reactions with acid and precipitation/re-dissolution of basic ferric sulphate and alunite.

Jan 1, 2004

By Michael R. Brown

A facilities success or failure of doing well during a regulatory inspection is typically measured by the number and type of citations that result, and financial liability resulting from those citations. The success of a facility during an inspection depends on several factors including, the preparation prior to an inspection, behavior and activities during and inspection, and finally, action taken following the inspection. This paper contains suggestions for improving inspection results and establishing an attitude of compliance at manufacturing and mining facilities.

May 1, 2002

By Matt Schuett

Antamina Mine Facts • Surface Water Design Principles • Drainage Areas • SEDCAD Modeling • Impacted Runoff Collection • Clean Runoff Collection • System Flexibility • Outfall Construction

May 1, 2004

By Robert B. Parsons

"1984 was an eventful year in the courthouse f or observers 0/ the mining tax scene in Canada. For the first time in a number of years, the Federal Court heard several important tax cases which pertain directly to the resource industries. Tax Notes discusses/our cases that could affect the taxation 0/ operations and investment in the mining sector.Capital Gain or Income?Ever since tax reform, risk-takers in the exploration business have maintained that the taxation of capital gain s is a significant impediment to raising risk capital. It must be akin to rubbing salt in the wound, then, when an entrepreneur sells shares and the Court upholds Revenue Ca nada taxing the gain as ordinary income instead of capital gain. But, this is precisely what happened in the case of The Estate of Murray Watts, et al. v. The Queen.The issue that had to be decided by the Federal Court, Tri al Division, in this case was whether or not the profit from the sale of shares in Hearne Coppermine Exploration s Limited in 1968 was a capital gain, or income subject to tax.Hearne was incorporated in July, 1967. At that time, the three plaintiff s, together with seven other individuals, subscribed for 400,000 shares at 10 a share. The plaintiff subsequently subscribed for an additional 500,000 shares at $1.A pooling agreement was entered into by all ten shareholders regulating the disposition of any o f their shares; any sale required approval of seven of the ten initial sub scribers. It also provided for the sale of their shares 30 days after any public offering."

Jan 1, 1985

By D. W. Davis, P. Landais, L. J. Robb

Abstract -Nodules of carbonaceous matter have been observed in several Archaean peraluminous granites adjoining the gold- and uranium-bearing Witwatersrand Basin. These nodules, which resemble solid bitumen, usually replace uraninite or uranothorite and are paragenetically late. They show many similarities to kerogen seams and nodules associated with the conglomerate horizons in the Witwatersrand Basin, including composition, maturation, intimate association with uraninite, and a late paragenesis. U-Pb isotope ratios for granite-hosted and Witwatersrand kerogens define a single, albeit somewhat diffuse, Pb-loss discordia suggesting an upper intercept age of circa 2300 Ma. Carbon isotope analysis indicates lighter ?13C values for the granite-hosted nodules than for the sediment-hosted kerogen seams. Raman spectroscopy indicates that granite-hosted kerogen is more highly ordered than Witwatersrand seam kerogen. A model is presented which links the granitoid­ and sediment-hosted organic matter to an event of oil generation in the Witwatersrand Basin circa 2300 Ma ago. Light hydrocarbons migrated through the sediments and into underlying/adjacent granitic rocks, undergoing polymerization and accumulation in response to radiation accompanying the presence of high-uranium phases.

Jan 1, 1994

By A. E. Boone

"The paper presents critical areas in which improved coordination of effort by industry, government and sup-pliers will be essential to continue the growth record of the Canadian mining industry into the 'seventies'. The analysis includes: exploration, production, mining methods, research and development, markets, management and industrial relations. Performance objectives are suggested where tangible results can be measured. The author suggests the methods by which the 'seventies' can be the greatest decade in the history of Canadian mining. It is indicated that a national mineral policy is essential to the Canadian mineral industry."

Jan 1, 1970

By A. Dreimans

Tracing of 'float' against the latest ice-flow directions ha!' led to or assisted in discoveries of several mineral deposits in Canada at lP.ast since 1891, e.g., fluorite and corundum in eastern ?Ontario, Steeprock and Josephine iron ore in western Ontario, Malartic, Fisher-Quebec, and Lamaque gold ore, and Vendome zinc ore, in western Quebec, Sullivan zinc and lead sulphides in British Columbia, Orvan Brook or New Calumet sulphide deposit in New Brunswick, Lynn Lake nickel sulphide de-posit in Manitoba, etc. Pebbles or ore boulders whose source has not yet been found include diamonds in the Great Lakes region and ?sulphides in several localities in Ontario and Quebec. Complexity of transport of ore boulders, including non-glacial transport, may be the explanation. Tracing of ore boulders requires knowledge of the Pleistocene history of each particular area (ice flow directions, their ?changes during glacial oscillations, existence of pre-glacial lakes with ice-rafted boulders, later interference by streams, lakes, mass movements). Important also is distinction of till from similar non-glacial deposits and knowledge of the bed-rock geology. Quantitative methods, e.g., pebble counts, maybe applied while tracing magnetite, hematite, or goethite. Fragments of sulphide ores are less abundant in indicator trains, and quantitative methods are less suit-able for tracing them. Heavy-miner-al investigations may give good results for minerals resistant to weathering. Geochemical methods are of value only in the vicinity of ore deposits.

Jan 1, 1958

By F. Crundwell, N. Steenekamp

"The leaching of sulphide minerals generates a significant amount of energy. There are three systems that might be used to remove this energy. These are: cooling coils, quench water, and flash recycle. Flash recycle is the recycling of slurry from the autoclave to the feed tank. Heat is removed in this arrangement when the slurry at elevated temperature and pressure is flashed to atmosphere, releasing steam. The slurry is returned to the autoclave at lower temperature, resulting in cooling. The cooling is directly proportional to the steam released from the recycled slurry. Design equations and results for the flash recycle system are presented. A fourth proposal for removing heat is to recycle slurry from the back of the autoclave. These four alternatives not only remove the heat, but also have an effect on the leaching efficiency. Amongst the four alternatives, design calculations indicate that the flash recycle option is the optimal solution in terms of leaching efficiency and heat removal, and recycling product from the back of the autoclave is the worst. In spite of its efficiency in terms of heat removal and leaching, the implementation of the flash recycle system is limited to a few operations in the platinum industry.INTRODUCTIONIn considering ways to improve leaching operations, focus is placed on the chemistry, on the kinetics, the agitation and perhaps even on the gas mass transfer conditions. Attention is less frequently placed on the removal of energy from these reactors and how this might limit performance.The pressure leaching of sulphides releases a significant amount of heat. For example, the reaction for the leaching of chalcocite, Cu2S, given by"

Jan 1, 2012

By R. A. Campbell

Pig iron and silicospiegeleisen were produced experimentally from a very low-grade manganiferous iron ore from Steep Rock, Ontario, by a two-stage electric smelting process. The most favourruble operating conditions were determined for each stage. Cement clinker then was made by calcining the slag from the second stage of smelting, with additional limestone and alumina. (This slag would normally be a waste material). The cement clinker produced had the composition of commercial Portland cement, and met the physical test requirements of the Canadian Standards Association Specification A5-1951 for normal Portland cement as well as could be expected for a material produced on .such a small scale.

Jan 1, 1958

By R. J. Craig

Introduction All mining operations produce rock dust. Inhalation of rock dust, particularly if it has a high silica content, causes silicosis. Silicosis is, therefore, recognized as a hazard of the mining industry and has been made compensable throughout most of Canada. Most of the dust in any mining operation is caused by rock drilling and blasting operations and the movement and transportation of broken rock. Dust from blasting cannot be eliminated, but it can be controlled by means of increased ventilation, the use of water sprays, and the control of blasting hours. Dust from ore movement can be reduced by keeping the broken rock in a moist condition at all times. The dust from the rock drilling operation has been found to be the most difficult to control. Concentrations of dust caused by rock drills in stopes can usually be reduced to the safe minimum of 300 particles per cubic centimeter (p.p.c.c.) by diluting the air with increased ventilation. In development headings, where the machines are more confined, this is not always practicable. Therefore, the dust must be eliminated at its source. This paper deals with the reduction of dust from Leyner machines by adopting improved designs.

Jan 1, 1947

By Gordon A. Gross

During the last half century major steel industries of the world have become dependent on iron and manganese resources derived from siliceous ironformation sediments. More than two billion years ago vast amounts of iron and manganese were deposited in ironformation sediments on all continents and until recent years their genesis was considered to be a uniquely Precambrian phenomenon. Research work has demonstrated that the origin of the banded ironformations was related to major tectonic features and associated volcanogenic processes that were active throughout geological history. Similar sedimentary-tectonic environments are being explored on the seafloor where metalliferous sediments are forming today. Ironformations are now considered to be a major part of the stratafer group of stratiform metalliferous deposits. They developed in sedimentary basins in areas where deep tectonic fracturing intersected high thermal gradients in the earth?s crust and gave rise to profuse volcanism and the hydrothermal effusive discharge of metals in the vicinity of the volcanic centres. Concepts for the genesis and metamorphism of stratafer deposits as revised in the last half century have had a profound impact in the development of iron ore resources and have had a dramatic impact in the use of metallogenetic concepts for guiding exploration for other mineral resources. They are based on the tectonic history and stratigraphy in the sedimentary basins, the role of hydrothermal volcanogenic processes , as well as environmental and sedimentation factors which influence the deposition of silica, iron , and other metals that were emphasized in the past. Topics of special interest in the genesis of ironformation and stratafer deposits and for guiding mineral exploration are: biomediation in their sedimentation and genesis, the significance of metamorphism in the processing and beneficiation of iron ore and in the genesis of iron ore by natural enrichment processes, syngenetic concentrations of Mn, Ti, Cu. Zn, Pb, Ni, Co, REE, F, Ba, B, As, Hg, W and Au in ironformations and stratafer lithofacies, and the mobilization of gold and other elements by alkaline solutions during diagenesis of ironformation and other stratafer metalliferous sediments.

May 1, 2003

By F. H. Edmunds

I N presenting this paper, the writer wishes to point out some of the difficulties and problems of geological work in that part of Saskatchewan in which outcrops are few. These problems are well known to all geologists who have made investigations in this region, but may not be so well known to those outside. A table of the strata as known in certain areas of Saskatchewan and the adjacent provinces is given, with a brief discussion of some of the formations and beds about which there is little knowledge due to their being deeply buried and not exposed in the region. Comment with regard to possible oil and gas structures is made and some features of the structures in the Battleford and Simpson districts are described. The writer wishes to make acknowledgment to members of the Geological Survey of Canada to whose work in Saskatchewan and the adjacent provinces reference is made, and to others who have made, or are making, valuable contributions to the stratigraphy of Saskatchewan. Mr. G. C. Webb has kindly furnished information regarding and materials taken from a well bored recently in the Paynton district. Special thanks are due to the Simpson Oil and Gas Company for permission to use much valuable information with regard to their wells and for the generous way in which the officials and staff co-operated with the writer. The opportunities the writer has had to visit many parts of the Province have been in connection with investigations for the Provincial Department of Natural Resources and through facilities provided by the Department of Soils of the University of Saskatchewan. To these Departments the writer accords his thanks. For the purposes of this discussion, Central Saskatchewan may be considered as that portion of the Province extending from Township 16, with Regina, Moose Jaw, and Swift Current situated on or near the southern boundary, to Township 48, with Prince Albert and Lloydminster on the northern boundary. This region includes territory underlain by Cretaceous sediments and excludes the southern portion of the Province, where Tertiary beds underlie the surface and are exposed to an extent sufficient to permit a measure of systematic mapping.

Jan 1, 1937

By Harry Siewert, Tom Milner, Jack Stickney

"LocationThe Gibraltar mine is located in central British Columbia (NTS 93B/9W), 362 km north of Vancouver. Access is provided by 20 km of paved road from McLeese Lake, which lies 45 km north of Williams Lake on Highway 97. Latitude and longitude of the mine are 52° 30' and 122° 16', respectively.The total area of the McLeese Lake site is approximately 1700 ha (4200 acres). This includes the orebodies, dumps, surface drainage collection system, plant site, roads and tailings ponds.Brief Description of OperationOre is mined by open pit methods and is concentrated using conventional crushing, grinding and flotation processes. Copper and molybdenum flotation occurs at an average rate of 40 000 tons per day. Tailing is discharged to an impoundment area and the water recycled as process water. Additional copper is extracted from the waste dumps using sulphuric acid as a leach solution followed by solvent extraction and electrowinning.HistoryExploration by Gibraltar began in 1964, continuing until late 1970, at which time it was announced that the property would go into production. Construction started in early 1971, with initial production in March 1972. Target capacity of 30 000 tons per day was achieved by the end of March and is currently at 40 000 tons per day.Ore reserves as of January 1, 1998 were 184 384 000 tons grading 0.31% Cu and 0.010% MoS2."

Jan 1, 2000

By M. Tanaka, T. Oishi, K. Koyama, S. Alam

"A novel hydrometallurgical process for copper recovery from waste printed circuit boards has been proposed, which consists of selective leaching of copper metal as Cu(I) by Cu(II) in ammoniacal alkaline solution, purification, and electrowinning. The distinct feature of this process is much lower power consumption during the electrowinning than that during the conventional one from acidic copper sulfate media, because the deposition of copper metal from Cu(I) at the cathode and the oxidation of Cu(I) to Cu(II) at the anode take place in the present method. In the laboratory-scale tests using waste printed circuit boards, high purity copper which contains 1.1ppm of impurities was obtained in a chloride system. INTRODUCTIONThe recovery of various metals from waste materials is an important issue in order to conserve the environment and metal resources. Copper is used for cables, electric appliances, etc., and is currently a very important material for industries and will continue to be in the future. Among the wastes that contain copper, one of the most complex recycling materials is electronic scrap like printed circuit boards (PCB), which generally contain 10-30% copper as well as plastics, fibreglass and other metals. There are two ways to recover copper, either pyrometallurgical or hydrometallurgical. Hydrometallurgical treatments generally have more flexibilities in the process scale and control. The separation processes tend to become complicated because of the poor selectivity during the leaching in the sulphuric and hydrochloric acid media. On the other hand, the use of ammonia as a complexing agent, gave a higher selectivity for copper leaching (Nigo, Majima, Hirato, Awakura, & Iwai, 1993; Majima, Nigo, Hirato, Awakura, & Iwai, 1993; Zhou, Shinme, & Anezaki, 1995; Koyama, Tanaka, & Lee, 2006) .In this study, recycling process containing leaching, copper deposition at a cathode and oxidation of copper(I) at an anode from ammoniacal alkaline solutions containing Cu(I) or Cu(II) is introduced. Furthermore, copper recovery from a waste printed circuit boards and impurity behaviour was examined in ammonia-ammonium sulfate (sulfate system) and ammonia-ammonium chloride (chloride system) systems."

Jan 1, 2012

By J. A. C. Ross

Introduction To enlighten those who may be wondering where anyone could find sufficient data to write a paper on underground concrete work, the author would like to explain that, at Copper Mountain, we have found it necessary to line numerous headings with a layer of concrete in order to keep them in a safe and serviceable condition. The majority of these headings are scram drifts and ore-pass raises. This paper will therefore deal, in the main, with the methods of and reasons for placing concrete in these headings. During recent years, radical changes have been made in the methods of mining ore at the Copper Mountain mine. After considerable experimenting, a mining system has been developed making use of diamond drills for primary breaking and transfering such broken ore through scram drifts with slusher hoists. With the advent of scram drifts, it soon became apparent that some substantial means of reinforcement and protection for the scram drifts themselves would be necessary. Since the orebodies in this mine are cut by numerous dykes or faults, and often both, it was anticipated that some means of support would be required where headings necessarily passed through these incompetent zones. Further, as experience was gained, scram drifts were driven into pillars and in close proximity to old workings so as to recover the maximum amount of ore. In such places, the ground is often severely fractured, either as a result of previous mining or from the effect of excessive rock pressures.

Jan 1, 1950

By Pritii Tam Wai Yin, Tony Leong, Neetu Bansal, James Vaughan, Amiel Boullemant

Mercury is a toxic element that is associated with many industrial activities including the Bayer process. Mercury is known to enter the Bayer process with the bauxite feed material and has the potential to accumulate as the process solution is recycled. This paper explores the speciation of mercury in Bayer process streams. The process parameters considered are the oxidising-reducing potential, basicity and temperature. The results of a refinery circuit survey are presented and compared with the thermodynamic predictions. Electrochemical measurements on relevant synthetic systems are also included.

Jan 1, 2014