Search Documents

By D G. Boxall

As an alternative to heavy water cooling, reactors cooled by organic liquids are being actively developed in Canada under the sponsorship of Atomic Energy of Canada Limited. One of the areas in which development has been required is that of core materials. The factors affecting the selection of fuel canning and coolant tube materials are discussed. It is shown that S.A.P. is a potentially attractive material for these applications. The fabrication of fuel sheathing is discussed. Difficulties met due to large inclusions and blistering due to high hydrogen contents have been overcome by magnetic separation and vacuum sintering of the powders. High-quality tubes can now be produced by extrusion to finished size. A study has been made of the mechanical properties of fuel-sheathing tubes and bar stock. The stress rupture properties of the tubes subjected to uniaxial and biaxial stress have been determined. The biaxial stress tests were performed by internal pressurization. For times in excess of about 200 hours, the curve of stress against time to rupture is extremely flat. The secondary creep rates of

Jan 1, 1965

By E. P. Williams

"Prince Edward Island, Canada's smallest Maritime Province, is located in the southwestern part of the Gulf of St. Lawrence. The Province is more or less centrally located in the Maritimes Basin, a large intermontane basin within the Appalachian orogenic belt. The Maritimes Basin is subdivided into sub-basins and uplifts which exhibit two dominant structural trends: east and northeast. The Basin is known to be petroliferous because of the seeps, shows, oil shales and albertite found in southern New Brunswick and northern Nova Scotia and the gas and oil produced from the Stony Creek field near Moncton, New Brunswick.Permian beds are exposed on the Island, mostly along sea-cliffs. A maximum thickness of about 5,000 feet of red beds -shales, sandstones and conglomerates -make up the sequence. Over most of the Island, the Permian section is much thinner. Four key wells (Mississippian tests) and several shallower tests have been drilled. The Pennsylvanian-Mississippian section thickens rapidly off the Port Hill Uplift at the northwest, where it is less than 4,600 feet thick, and continues to thicken to about 20,000 feet in the Cumberland Basin at the southeast. Geological and geophysical data combine to give us the structural picture of the deeper beds.Prospective reservoir rocks are primarily in the Missis-sippian Horton and Windsor groups. Prospects are:-1. on or over structural highs in the basement; 2. on anticlines or fault highs; 3. over or peripheral to salt domes or salt-core anticlines; 4. at truncation pinchouts of Mississippian prospective beds; 5. in basal sandstone or granite wash on the pre-Carboni-ferous basement; and 6. in facies traps at changes from sandstone to shale or porous to tight carbonate rocks."

Jan 1, 1967

At the end of a century of mining education in South Africa, it is appropriate to reflect on the past, take stock of the present and ponder the future of mining education. While it is likely that changes in the mining industry will generate an increased demand for mining graduates, the number of suitably qualified applicants to study mining is worryingly small. While good progress has been made in unifying the educational system that previously provided schooling on a racially separate basis, it appears that a decade or more will be required to raise competency levels in mathematics, science and English, and this paper describes the process as it affects mining engineering programs. It also describes the initiatives currently being undertaken by the University of the Witwatersrand and the mining industry to ensure that the South African industry receives an adequate flow of well-qualified mining graduates, despite more than 70% of the intake coming from severely disadvantaged educational backgrounds.

Jan 1, 1999

By Tracey Bodnarchuk, Philipp Mirzoev

Sulfate balance control is a common problem for zinc plants. Roast-leach-electrowin plants are mostly concerned with the over-generation of sulfates while for the HudBay direct leach plant both extremes are possible including potential necessity to buy sulfuric acid to replenish a sulfate-depleted circuit, which makes the problem doubly important. Quantitative methods were applied at the HudBay plant to analyze sulfate generation/depletion based on a local sulfur balance and sulfate extraction calculation in the leach circuit, using a Pb-tie method. Main factors were established influencing sulfate generation/depletion, including the critical role of Pb and pyrite. Regression analysis proved to be effective and allowed the quantitative prediction of Pb concentrations necessary to reach the equilibrium for the sulfate balance. This in turn provided a firm basis for a sulfate-control strategy realized through concentrate blend correction, which allowed the plant to fine-tune sulfate generation/depletion effectively reducing economic consequences of excessive/deficient sulfate generation.

Jan 1, 2015

By S. S. Sephton, Kirit C. Vyas, Melvin J. Greaves

Energy requirements for various pelletizing systems are considered from a fuel and power aspect, with the presentation of typical energy heat balance flow sheets. A partial calculation for the firing zone of a straight grate system is shown and a comparison of an actual measured and a theoretical-calculated heat balance for a grate-kiln is presented. The power used for each pelletizing system and future possible energy savings a1•e also reviewed.

Jan 1, 1976

By C. R. Ross

"THE ASSESSMENT of pneumoconiosis-producing dusts in mines and other industries is usually undertaken for one or more of three reasons: (1) To compare dust exposures at particular operations with standards of permissible dustiness in order that hazards may be evaluated and preventive procedures initiated where required.(2) To study particular operations with the objective of improving dust control devices or procedures by locating dust sources. (3) To obtain data which, along with the results of medical investigations, may assist in understanding the causes of dust-induced diseases or aid in the establishment of permissible standards of dustiness. Most dust measurements are made for the first of these reasons -to evaluate dust hazards so that they may be controlled. For this purpose, four quite different assessment techniques have been in widespread use for many years. One of these is based on the konimeter, an instrument familiar to most .Canadian mining men; a second on the impinger, which is also widely used in Canada, and almost exclusively so in the United States; a third on the thermal precipitator, used extensively in Britain and South Africa; and a fourth on the tyndallometer, a light-scattering instrument used in Germany."

Jan 1, 1960

By K. Adham

Both the dry and the wet fluorination systems require hydrogen fluoride (HF) for the process of uranium conversion to uranium hexafluoride (UF6). The dry methods depend on the electrolysis of HF to generate the fluorine (F2) required for the high temperature pyro-fluorination. The wet methods require aqueous HF in water solutions for the low temperature hydro-fluorination (Argonne, 2019). This paper uses the available HF safety guidelines and industry information to discuss the issues of transportation, storage and utilization. Health effects and environmental considerations are reviewed. Safe practices for handling the HF (both as anhydrous and as aqueous) are considered. Proper selection of different materials of construction are discussed, for both the anhydrous and the aqueous HF.

Jan 1, 2020

By J. Postle, Deborah McCombe

"This is the third in a series of articles about the Committee for Mineral Reserves International Reporting Standards (CRIRSCO). The first article was an interview with Niall Weatherstone, Chairman of CRIRSCO (CIM Magazine, February 2008) the second described the background and goals of CRIRSCO (CIM Magazine, March/April 2008). In 2007, CRIRSCO was adopted as the Reserves and Resources Task Force of the International Council on Mining and Metals. This decision by ICMM has resulted in an increased level of funding for CRIRSCO and the ability to advance its objectives. In mid-October 2007, CRIRSCO members met in London England to discuss the status of each of the member countries’ reporting codes and the progress of various CRIRSCO projects. Update on national reporting codes Australia: The last update of the Australian JORC Code was in 2004. While there are ongoing discussions about issues that arise from the application of the latest version of the Code, there are no plans to update JORC in the near future. Canada: The Canadian Securities Administrators revised National Instrument 43-101 in December 2005. At the same time, the Canadian Institute of Mining, Metallurgy and Petroleum published updated Resource and Reserve Definitions that are incorporated by reference in NI 43-101. CIM is continuing work on developing Best Practice Guidelines to assist practitioners in the estimation of Mineral Resources and Reserves. South Africa: The South African Mineral Reserve Committee is currently awaiting an update of the Johannesburg Stock Exchange Limited Listing Rules, which will incorporate both SAMREC and SAMVAL (South African valuation guidelines). The official launch of both codes is expected in 2008. Europe: The Pan-European Reserves Reporting Committee expects to release a consultation draft in 2008. Emphasis is being placed on industrial minerals and aggregates, which constitute a very large industry in Europe. Chile: The Chilean Certification Code was approved in early 2008. As part of the Code, a National Commission is being established to screen and review reports on a random or specific basis. United States: The Society of Mining Engineers updated the SME Reporting Guidelines in 2007. The Securities and Exchange Commission has not accepted these more up-to-date definitions and guidelines. The SME committee will continue to discuss the incorporation of these Reporting Guidelines with SEC. SME has also established a class of membership, a Registered Member, which includes disciplinary measures for non-compliance with the SME guidelines."

Jan 1, 2003

By W. D. Madeley

Synthetic minerals were made from pure starting materials and galena samples were doped with the title metals. Microscopic, microprobe and X-ray examination confirmed that the dopeants were in solid solution. Paired flotations in a Hallimond-tube apparatus were performed to determine relative flotation response using Aerofloat 238 promoter. Results of these tests show that silver-doped galena floats more readily than pure galena and that galena doped with bismuth floats less readily than pure mineral to a 95% confidence level. Galena doped with both silver and antimony as AgSbS2 shows no detectable effect. Antimony-doped galena followed the expected trend, but not to 95% confidence. The results are consistent with the theory that flotation by thiol-type anionic collectors is enhanced by p-type semiconduction.

Jan 1, 1978

By Jun Wang, Bo Zhang, Wenqing Qin, Guanzhou Qiu, Xiaozhen Ma, Key Lab of Biohydrometallurgy of Ministry of Education, Fen Jiao, Central South University, Yansheng Zhang

"Arsenic contained in minerals sulphides such as enargite and tennantite can represent not only a significant penalty element in base metals production, but also a disadvantage to the environment through producing the toxic emissions to the atmosphere. The achieving separation of arsenic bearing minerals either at an early stage in floatation or from the floatation concentration is significantly beneficial to the economic. However, there was no feasible commercial method of separation at the flotation stage because of its similar flotation properties with many other copper sulphides. In this work, the selective floatation of enargite from copper sulphide concentrate containing maily covllite, chalcoctie, bornite and enargite was investigated. A low arsenic concentrate with As 0.2%, Cu 22% and a high arsenic bulk concentrate with As 7.65%,Cu 33.65% were obtained. It was indicated that Ca(ClO)2 is the effective depressor and the optimum floatation condition was obtained. Most enargite could be floated at pH 11 and controlling the pulp potential at 290 mV SHE. Furthermore, the arsenic removal from the high arsenic bulk concentrate by hydrometallurgy methods was study. The results showed that the reaction temperature and the concentrations of NaOH were the most important variables affecting the rate of arsenic removal. A low arsenic concentrate with As 0.24%, Cu 37.80% was obtained in the optimum leaching condition.INTRODUCTIONArsenic is mainly produced as a by-product of base metals smelting, in particular copper concentrate. China has imposed an upper limit of 0.50% arsenic for concentrates entering (Long et al., 2012). Arsenic amount of copper concentrate within 0.40% has also been imposed in China, and above which will be introduced about 50 RMB penalties per ton for each 0.10% increasing by smelters now. Therefore, it is necessary to remove arsenic from the copper concentrate.In copper concentrate, arsenic is mainly in the form of arsenopyrite (FeAsS), enargite (Cu3AsS4) or tennantite (Cu12As4S13). There are two types of arsenic in the separation of copper and arsenic: arsenopyrite and arsenic bearing copper mineral. It is easier to separate arsenopyrite from the copper sulphide by flotation in comparsion with the separation of enargite or tennantite from non-arsenic copper minerals (Pineda et al., 2015). The main difficulty in the separation of arsenic copper mineral from non-arsenic copper sulphides is their extremely similar floatability, which depends on the fact that tennantite and enargite contain high copper content (Pineda et al., 2015)."

Jan 1, 2016

By E. Nolasco, J. Ouellet, T. Tikka

"Shaft bottom structural systems are used in underground mining to support transfer of personnel, equipment and ore to and from underground to the surface. This paper first summarizes the evolution of design philosophy from a concrete tower supported on a concrete plug to the current structural steel design arrangement with unlined shaft walls, clear shaft bottom area with only a concrete housekeeping pad. Then the paper reviews the design parameters, analysis and design, and construction methodology for this rather unique shaft bottom structural system consisting of three sets of hitch beams, with each having specific functional requirements. INTRODUCTION Shaft bottom structural systems are used throughout the world in underground mining operations to provide a means to support the transfer of personnel, equipment, materials, ore and waste entering and exiting a vertical shaft ready for transport to and from the surface via the hoisting system. The shaft bottom structural system, for the Service Shaft (SS) at the Jansen Mine, is designed to accommodate two skips, a personnel/equipment cage, counterweight, services, loading pocket, rope changing, arrestor system, crash (or catch) beams, access platforms, stairs and rope divider system. Stantec and BHP have engineered a unique structural steel shaft bottom system for hoisting system at a Potash Mine. The shaft bottom structural system connects to a fixed guide and cantilever bunton system, used in the vertical shaft (shaft barrel), above the shaft bottom. The geometry for the shaft bottom structural system, shown in Figure 1 a), features three sets of hitch beams, beams which span across the shaft excavation or barrel. At the top of the structural system are two upper hitch beams. These hitch beams support a 64 metre suspended rectangular braced tower (upper tower), complete with steel guides for the conveyances. The upper tower passes through the main station (potash or mining) level and then connects to the top of the arrestor (lower) tower structure via a sliding vertical connection. The potash level is supported by two hitch beams spanning the shaft and loading pocket excavations. The arrestor tower, a braced compression tower structure, is carried by a third set of hitch beams. Below the third set of hitch beams is a short suspended tower complete with access platforms, stairs and the rope divider system."

Jan 1, 2019

By S. Constantinides

"A major use for many of the rare earths is in permanent magnets. While alternate technologies are in research or already exist, rare earth magnets are unlikely to be supplanted as a major input to clean technologies and high efficiency consumer and industrial devices. We’ll examine where and how the magnet rare earths are utilized and the size of the market. Market growth forecasts based on global markets will be presented. A brief explanation of materials research in the US completes the material.INTRODUCTIONRare earth magnets, first commercialized c.1969, have become essential for a wide range of consumer, industrial and military devices. They are used in the speakers and vibrator motors of cell phones. Rare earth magnets spin the hard discs within the drives and rare earth magnet voice coil motors position the read/write head over the spinning platter. Rare earth magnets are the heart of motors and generators used on airplanes – they are smaller and lighter weight than alternative materials/devices. Now rare earth permanent magnets are being introduced into electric vehicles and wind power generation.Rare earth minerals are difficult to extract from the ores and to separate from one another. The increase in use of rare earth magnets has placed a severe strain on established sources of supply. The establishment of new mines and processing facilities is costly and requires upwards of 15 years to become productive. The combination of rapid rise in use of rare earth minerals coupled with supply shortages has caused rapid price increases and threat of non-delivery of product. The result of this disruptive situation has been a profound response at several levels: corporate, industry-wide and governmental. Let’s learn more about why rare earth magnets are so important to modern society."

Jan 1, 2012

By François Robert, Steve Green, Tyson Birkett, Dan Richardson

Abstract -Detailed sampling using a portable diamond drill, and interlaboratory comparison of selected samples have been combined with statistical studies of truncated populations to establish the gold content of several outcrops in the Val d'Or area. The outcrops chosen are non-mineralized. The background gold concentration in the rocks of the region is 5 ppb or Jess. Gold is distributed relatively homogeneously within the outcrops studied except for slightly increased concentrations within quartz-tourmaline veinlets. Three samples, of which 20 grams of powder are analyzed for each, can adequately determine the gold concentration of a structurally simple outcrop in the Val d'Or area.

Jan 1, 1992

By James D. Bamburak

Total mineral production in Manitoba has averaged C$1 billion over the past ten years. Industrial mineral production has comprised almost 10% of the total, with more than half coming from the aggregate sector. In southeastern Manitoba, tantalum, spodumene and amblygonite concentrates, cesium and rubidium ores, cesium formate, dimension stone and sphagnum peat moss are produced. Gypsum, high-calcium limestone and lime are produced in the Interlake area. Early industrial mineral production consisted of tools and implements, salt and pottery. Historical production has included: salt, building stone, aggregate, lime and dolime, lignite coal, gypsum, natural and Portland cement, calcium bentonite, brick, light-weight aggregate, caustic soda and soda ash, and silica sand. Future industrial mineral production may come from reactivated quarries, pits and wells or from new producers of current commodities. Newproducts may include: stainless steel master alloy, silicon metal, titanium and magnetite, lithium carbonate, float-plate glass and ferrosilicon, "marble" dimension stone, magnesium metal, potash and kaolin.

Jan 1, 2001

By M. Peshko, J. C. Gingerich, L. W. Matthews

"Noranda has successfully developed and implemented two leading-edge mineral exploration technologies — hyperspectral remote sensing and 3-D seismic surveying. Airborne hyperspectral imaging provides detailed geological and mineralogical mapping capability at both a regional and project scale that facilitates improved selection of prospective terrain and an accelerated exploration cycle. Noranda, in partnership with Falconbridge, has licensed the exclusive use of the Earth Search Sciences Inc. (ESSI) Probe-1 hyperspectral scanners (128- channel, 0.43 µm to 2.5 µm spectral range) that are capable of mapping in excess of 3500 km2 per day at 10 m pixel resolution. The technology has been successfully deployed on four continents over a broad range of terrain from desert to boreal forest and the high Arctic.To augment the company’s deep search initiatives, Noranda has successfully modified and implemented existing 3-D seismic technology to help targeting massive sulphides located at depths ranging from 500 m to 2000 m. In the fall of 1998 and early 1999, Noranda completed an 18 km2, 3-D seismic program in eastern Canada by successfully drill testing acoustic impedance anomalies locating massive sulphides at depths in excess of 1100 m."

Jan 1, 2002

By Jim Excell, Jim Rothwell, Mike Rylati

"LocationThe Ekati Diamond mine is located at Lac de Gras, Northwest Territories.Brief Description of OperationBHP Diamonds Inc. has developed Canada's first diamond mine in the Northwest Territories (NWT), Canada. BHP Diamonds Inc. is part of the BHP World Minerals Division ofBHP Minerals. The project is a joint venture between manager and operator BHP (51%) and the Blackwater Group (49%). The Blackwater Group comprises Dia Met Minerals Limited, Charles Fipke and Stewart Blusson.Production at the NWT diamonds project began in October with the mine officially opened October 14, 1998. The project is situated on an 853 000 acre claim block located in the Lac de Gras region of the NWT. It is about 300 km northeast of Yellowknife and 100 km south of the Arctic Circle. The seasonal winter ice road to the Echo Bay Lupin mine passes along the eastern margin of the project area. This allows road access each year from mid-January to mid-April. For the remainder of the year, the project is accessible only by air.HistoryIn 1980, Charles Fipke traced indicator minerals east from the Mackenzie River area. He discovered indicator minerals in the Lac de Gras area and staked mineral claims in 1989. A joint venture was formed between BHP and Dia Met in 1990, and in 1991, the first diamonds in the NWT were discovered at Point Lake by BHP and Dia Met. This initiated the largest staking rush in Canadian history. The joint venture launched an aggressive exploration program.Koala, Fox, and Leslie were identified in 1992 as potentially economic pipes.As soon as the project's potential was established, it was recognized that an enormous amount of work had to be completed in several areas before a mine could be developed, namely: technical evaluation of the resources; environmental and socio-economic evaluation to procure the necessary permits for the development; and engineering design to optimize mining and processing of the resource and to comply with specific environmental requirements."

Jan 1, 2000

By E. J. Sides

In this paper, the argument is put forth that the codes used for public reporting of mineral resources and mineral reserves have some significant limitations with regard to the information provided to investors on the short- to medium-term value of mining properties. Such limitations include a) failure to explicitly incorporate a time element and b) failure to state explicitly the quantity and quality of mineral product that will be produced for sale. A time-value framework for reporting mineral assets is proposed in order to overcome these limitations. The proposed system is based on two classification axes: a) an X-axis representing time in years during which the value of the asset is likely to be realized and b) a Y-axis representing the value identified by a mining or exploration company\u2019s activities. The potential benefits of this system are discussed, including the ability to incorporate factors, such as permitting and construction times, directly into the magnitude of the reported mineral assets. The proposed framework would assist in the standardization of mineral assets reporting in such a manner that they could eventually be more readily included in financial statements. Year of Publication: Not explicitly mentioned in the document.

Jan 1, 2010

By L. Price, R. Hortie

Movement of ore and waste from the Hilton Mines pit is accomplished by truck haulage. With the aim of reducing costs, a study of truck fleet replacement was initiated. The study included on-site short-term tests and longer-term rental purchase agreements for haulage trucks. The operation and maintenance characteristics of different trucks, along with projected haulage conditions, were used to prepare cash flows, from which the most advantageous trucks were selected. The results of the study and implementation of the recommendations gave a cost saving greater than had been estimated. The study also indicated areas where improvements could be made, and resulted in much more attention being paid to road conditions, the training of operators and mechanics, and the development of a practical preventative maintenance scheme.

Jan 1, 1971

"The Cooperative Research Centre for Mining Technology and Equipment (CMTE) is funded by the Commonwealth Government, by its mining research members — the Universities of Queensland and Sydney and the CSIRO1, and by its industry members — BHP Coal, RioTinto R&TD, Hamersley Iron, Mining Technologies Australia, Pasminco, Shell Coal, WMC Resources, Advanced Mining Technologies, and Aberfoyle. The Centre conducts work aimed at improving the competitiveness of the Australian mining industry. The current work is focused in four areas: new mining and drilling systems, geological sensing, automation, and equipment maintenance and reliability. This paper describes much of the work in these program areas that relates to metalliferous mining. Mechanized Rock ExcavationThe disadvantages of the drill-and-blast excavation method are widely recognized and the last half of the 20th century has seen mining companies and mining research organizations aggressively pursue technology to excavate rock by other means. As discussed below, despite considerable effort and large amounts of funding, the quest for mining’s “Holy Grail” has been unsuccessful in all but the weakest rock types.COMRO (the Chamber of Mines Research Organisation) supported by the South African gold mining industry, spent three decades and (probably) tens of millions of dollars developing prototype drag bits and, later, impact breaking machines aimed at the mechanized stoping of narrow, tabular reefs. This work has not yet produced a commercially-attractive mining system. Work continues in South Africa to mechanize these stoping operations although now the emphasis is on the use of diamond-wire sawing techniques. This work remains in the experimental phase.Both British Coal and Germany’s Bergbau- Forschung spent many years developing techniques trying to extend the range of rock types which roadheaders could cut economically. Again, although new knowledge was produced, it is difficult to claim that any new commercial mining systems emerged from this work."

Jan 1, 2001

By Patrick Wong, Gareth Hatch, M. A. Halim, V. I. Lakshmanan, Darcy Tait

"This paper describes development of an integrated chloride process for separation and purification of REEs. The process includes atmospheric leaching of ore/concentrate with mixed chloride lixiviant containing HCl and MgCl2 followed by bulk recovery of REEs, dissolution of the bulk intermediate product, and separation of individual REEs by solvent extraction (SX) process steps. Mixed chloride leaching technology provides the opportunity to regenerate the lixiviant, while the addition of MgCl2 in HCl enhances the hydrogen ion activity by orders of magnitude increasing REE extraction efficiency at a lower concentration of HCl. An individual REE separation process developed by Innovation Metals Corp. is being piloted at a state-of-the-art facility at Process Research ORTECH Inc. in Mississauga, Ontario, Canada. The SX process includes the separation of light REEs (La – Nd), medium REEs (Sm – Gd) and heavy REEs (Tb – Lu plus Y) from leach liquor followed by individual REE separation. Each SX circuit proceeds by multistage extraction followed by scrubbing and stripping. The process is chloride based and reagents are recycled, reducing waste generation and optimizing water usage to reduce environmental impact.INTRODUCTIONRare earth elements (La to Lu plus Y) exhibit a range of unique magnetic, electronic, catalytic and optical properties. Due to these special properties, the application of REEs is increasing and they are found in components for wind power generation, hybrid electric cars, catalytic converters, and many electronic devices.Rare earth elements (REEs) are commonly divided in two groups: light rare earth elements (LREEs) and heavy rare earth elements (HREEs). Light rare earth elements include elements from lanthanum (La) to neodymium (Nd). Although promethium (Pm) is considered an LREE it is unstable and scarcely occurs in nature and is generally excluded. Heavy rare earth elements include elements from samarium (Sm) to lutetium (Lu) plus yttrium. Although rare earth elements are not rare and the rare earth oxides are scattered around the globe, over 95% of REEs+Y are currently produced in China (Pitts, 2011). On one hand the Chinese government is restricting the export of rare earth elements and on the other hand the demand for REEs+Y is increasing in the rest of the world. This has created an imbalance in the supply and demand of rare earth elements and has led to a rush for developing new rare earth projects."

Jan 1, 2016