Search Documents

By S. B. Kang

Magnesium has poor ductility at temperatures lower than 225°C and, as a result, Mg alloy sheets are produced via fairly complex thermomechanical processes consisting of numerous sequential steps of hot (warm) rolling with low reduction and intermediate recrystallization annealing operations. In context of the present study, a simple technology for the fabrication of magnesium sheets by hot (warm) rolling was applied to various magnesium alloys. The misch metal addition in those AZ alloys was done to evaluate the deformation behavior. Tensile tests were carried out for those AZ alloys after applying different heat treatments. The precipitation of ß phase (Mg17Al12 phase) induced different microstructures with various cooling method from solution treatment temperature, and also with various annealing treatment temperatures.

Jan 1, 2006

By T. W. Wlodek, Zygmunt Kowalczyk

In the period from 1946 to 1964, the annual output of co al from Polish mines increased from 4 7.3 to 117.35 million tons. In this paper, the methods of bringing about this increase in productivity through the building of some twelve new collieries (producing some 15 million tons annually) and the modernization, reconstruction and extension of some thirty-six older collieries are discussed.

Jan 1, 1967

By A. W. Jacob

THE shatter cut, or burn cut as it is often called, is one in which the centre of the round is almost reamed out by drilling holes so close together that the blasting of a few holes shatters the rock embraced by all of them. The idea of shattering the centre of a face by shooting holes drilled parallel to one another is not new. Some miners have used this method for years past, when drilling quartz or a face near timber. But, they followed the age-old practice of first blasting the cut, then the square-up. It was not thought possible to shoot both together. In the case of machine men, the two largest contributors to silicosis are dust from drilling and dust from blasting. It follows, then, that material reduction of exposure to either constitutes an important step in lessening the incidence o silicosis. It was? the hope of being able to do away with the necessity of the men having to return early to a face, through dust concentrations of 60,000 to 80,000 particles per cubic centimeter, that aroused interest "in the shatter cut at McIntyre. Efforts to this end were successful. Now, with this kind of cut, all holes of a round are shot simultaneously.

Jan 1, 1942

By H. J. McQueen

Large-scale industrial production of pipe began with longitudinal hot pressure welding of wrought iron by passage of skelp (narrow strip with beveled edges) through a die or bell that curled it about a longitudinal axis until the edges were forced together. Such small to medium tubes could be reduced by rolling or drawing; with threaded connections, they were excellent for distribution of clean water and of illuminating gas for street, home and industrial lighting. Although steel lacks the fluxing slag for pressure welding it has hot strength similar to iron; hot-pressure bell welding was advantageously transferred to steel in long coiled strip with 50% higher cold strength. For pipe without weld-line defects, hot cupping followed by Pilger mill rolling produced tubing that revolutionized bicycle quality and high-pressure service for boilers and chemical processing. Mannesman hot rotary piercing produced long thick walled tube that permitted reduction or expansion by rolling to provide pipe sections up to 60 cm diameter and 12 m long. During 1910 - 1940, oil and gas pipeline technologies, notably welding evolved markedly as they proliferated in the United States, in response to far-flung petroleum fields, expanding industry consumption and the automobile revolution. In the Second World War combat pipelines were laid rapidly, such as: the Canol line through the Yukon to Alaska, and fuel supply lines across the channel and through liberated France. Perfection of welding techniques for both longitudinal and spiral weld large diameter pipe in combination with controlled-rolling of micro-alloyed steels made possible reliable Arctic pipelines. The development of pipe production and utilization in Canada is recounted. The fabrication techniques and metallurgical controls are explained.

Jan 1, 2005

By A. A. Brant

BECAUSE of its simplicity, the dip needle is widely used for locating magnetic rock formations in drift-covered areas. Although it responds only to strong magnetic disturbances, it has the advantage that surveys with it can be carried out rapidly, at relatively low cost, by untrained operators. More accurate surveys can be made with a much more sensitive instrument known as the magnetometer, but this must be operated by a specialist and the resulting survey costs are much higher. Mining men use the dip needle for the location of magnetic ores or mineral deposits associated with magnetic rocks. In certain districts, a survey with the dip needle may aid in solving geological structure. In the Little Long Lac and Crow River gold camps of Ontario, it has recently been used for these purposes. In interpreting the results of a dip needle survey, an understanding of the chief magnetic and mechanical factors determining the dip recorded by the needle is definitely necessary. For example, many observers locate a magnetic body by the highest dip values, apparently unaware that these frequently may not lie directly above the body. It should also be realized that a careful dip needle survey may yield information regarding the dip, breadth, and perhaps depth, of the magnetic body. Moreover, the observer should know when numerous closely-spaced dip readings are necessary, and when the dip may be measured at more widely separated intervals. The purpose of the following article is primarily to describe the factors affecting the registration of the dip needle, with a view to aiding investigators in a more accurate and complete interpretation of their results. To explain the cause of magnetic disturbances (anomalies) and the action of the dip needle, a knowledge of certain fundamental magnetic terms is necessary.

Jan 1, 1938

By G. A. Vissac

IN THE preliminary design of a coal washery, the most important factor to evaluate is the ash content of the final product. The ash content permissible may be imposed by market demands, but, in the final analysis, sooner or later - as most consumers today are buying coal on a 'heat value' basis - the coal operator has a certain margin of latitude. and the ash content of the coal to be delivered can be determined on the basis of maximum returns and highest profits. A few years ago, the most desirable separation was selected on the basis of the plus-minus 0.10; that is, the most desirable gravity of the separation was selected at the point showing a minimum amount of near gravities in the raw coal. The reason for this was an expected wide error over these near gravities. Today with the recent development of cry accurate, automatically controlled cleaning apparatus, a much larger latitude is possible, and the most desirable gravity of separation can be selected, almost exclusively, on the basis of the economic factors involved. To illustrate these new methods of investigation we shall give two examples, based on actual coals from the western United States.

Jan 1, 1957

By N. Thompson

The Right Hon. Viscount Long, late Secretary of State for the Colonies, in his inaugural address to the Empire Mining and Metallurgical Congress in London last June said: "I am more and more? convinced by every day experience that the development and strengthening of the Empire must depend upon individual effort and action, and that it is useless to look to Governments for assistance." I am inclined to agree with Viscount Long, to this extent, that the initiative must come from individual effort, but Government assistance is necessary to put the results of that effort and action into effect. It is perhaps fitting at a gathering of this kind to remind ourselves of the part the mining industry has played, not only in the development of the British Empire but in the world at large, in the promotion of modern civilization. We do know that all human progress has been coincident with the early discoveries in the recovery and treatment of metals and, as the centuries have passed, the human race has become more and more dependent on these sciences as factors of all progress, and no nation has ever become powerful and prosperous that has lacked adequate mineral supplies, or having these, has allowed them to be exploited by other nations.

Jan 1, 1925

By David J. Forrester

"CANMET’s research into underground coal mining is primarily conducted at the Cape Breton Coal Research Laboratory (CBCRL), established in 1981 to conduct safety research in underground coal mines. Located close to Canada’s largest underground coal producer, in the Sydney Coalfield of Nova Scotia, CBCRL’s program also includes the two western underground coal operations. CBCRL is a relatively small laboratory with a staff of thirteen — eight professionals and five support staff — with an annual budget of over $1 million. In order to maintain effective research response, flexibility is key and staff are increasingly working in project teams, crossing traditional section ties and also drawing from specialist expertise elsewhere within CANMET.CBCRL’s research activities have had a substantial impact on the Canadian underground coal mining industry, particularly in Cape Breton. CBCRL contributed to Cape Breton Development Corporation’s (CBDC’s) threefold reduction in lost-time accidents in the 1980s. Also, in the last four years alone, CBCRL’s work has enabled CBDC to save over $17 million in improved utilisation of reserves and cost savings. The work embraces the three traditional areas of mine environment, strata mechanics and mining technologies, however the current direction has been strongly influenced by recent external and internal factors. It is timely to review progress and recent directions."

Jan 1, 1996

By L. H. Thorleifson

Demand for both gem and industrial diamonds is very strong. Synthetic production supplies industrial uses, but synthetic gems remain inferior and expensive, so the large gem market is supplied by mining. Several major mines have been depleted, and the market is receptive to new sources of high quality gems. Canada's Precambrian terrane, extending across the Canadian Shield and under the Phanerozoic cover of the Plains and Hudson Bay, has excellent potential for diamonds, but exploration conditions are difficult due to recent glaciation. Early world exploration relying on recognition of diamond in alluvial sediments was adequate to launch pre- 1900 production from India, Brazil, and Africa. Exploration success in Canada, as was the case in Russia and other more recently discovered sources, however, had to await large investments in effort supported by advanced science and technology. Canadian exploration in many ways is similar to that in other regions, relying on analysis of tectonics, indicator minerals, geophysical surveys, and multiple stages of drilling and sampling. Very different from other regions, however, is Canada's surficial environment, in which recent glaciation has caused fresh indicator minerals to be transported hundreds of km. Exploration accelerated in Canada after 1960, first in Ontario and the Arctic Islands, then in Saskatchewan in 1988, and most importantly after the Chuck Fipke - Stew Blusson discovery at Lac de Gras, Northwest Territories, in 1991 that led to the billion-dollar BHP - Dia Met Ekati Mine that opened in 1998. In 2003, production from Ekati will be supplemented by that from the similar and nearby Diavik Mine of Rio Tinto and Aber. These mines will bring Canadian output to over 10% of world supply, and will position Canada with Botswana and Russia as world leaders in production of high quality gem diamonds. There could be other mines as well, as sites across the Arctic and in the south from Alberta to Québec are being explored by an array of companies, including De Beers, other majors, and several juniors.

May 1, 2003

By Staff

This paper contains an outline of the history of the Sullivan mine, now owned and operated by the Consolidated Mining & Smelting Company of Canada, Ltd.; some account of the various methods by which the ore has been treated in efforts to solve the metallurgical problems which its complex character presents, and, finally, to give, as concisely as possible, an outline of the present mining and metallurgical practice along with a description of the mining and milling plant at Kimberley and the smelter and refineries at Trail, in British Columbia. EARLY HISTORY In May, 1892, Pat Sullivan, John Cleaver and Mike Holland left the Coeur d'Alene country, in the State of Idaho, to seek their fortunes in the Kootenay lake district in British Columbia. They were aided in their venture by James Cronin, afterwards locator and owner of the St. Eugene mine at Moyie. Two months later the party broke up, Sullivan and Cleaver crossing the mountains from Crawford bay on Kootenay lake to the head waters of the St. Mary's river, the course of which they followed down to Fort Steele. Here they found a good deal of excitement about the North Star mine, and, joined by "Ed." Smith, who was familiar with this part of the country, they determined to return and prospect in its vicinity.

Jan 1, 1924

By John C. Luck Jr.

"DEVELOPMENT of oil emulsion mud dates back to the early days of rotary drilling when oil was added to the drilling mud solely for the purpose of freeing stuck drill pipe. After the drill pipe was freed, and drilling resumed, this oil was considered a contaminant. Efforts were made to remove the oil but some of it remained and was emulsified with the drilling mud, thus forming a mechanical emulsion.During the late 1930's, operators found that adding crude oil to drilling muds seemed to alleviate 'sticky-hole' problems and so oil was allowed to remain in the mud. This practice was adopted when it was found that faster drilling rates and longer bit life were obtained. These observations led to the development of emulsion drilling muds. During the past five years their application has become more widespread because of the lower fluid losses obtained, greater lubrication qualities, faster penetration rates, and generally better hole conditions.An emulsion may be defined as a two-phase system consisting of a mixture of either finely divided oil droplets in water or of finely divided water droplets in oil. The surrounding liquid is known as the continuous phase. The emulsifiers reduce the interfacial tension, making the droplets tend to repel each other so that they remain dispersed and stabilized. These emulsions are classified as oil-in-water or as water-in-oil, depending upon whether water or oil, respectively, is the continuous phase. Briefly, close inspection shows that they consist essentially of globules of• the one liquid suspended in a continuous mass of the other liquid. Oil emulsion muds are usually of the oil-in-water type. Two basic types of emulsifiers •commonly used in Canadian muds are soaps and lignites."

Jan 1, 1954

By D. R. Lentz, J. A. Walker

"Abstract -The Flat Landing Brook Zn-Pb-Ag deposit of the Bathurst Mining Camp occurs within a narrow thrust-bound nappe containing felsic volcanic and volcaniclastic rocks of the Tetagouche Group. Within the host nappe, the Tetagouche Group is represented by the Nepisiguit Falls Formation and the overlying Flat Landing Brook Formation. The Nepisiguit Falls Formation is divided into two members: quartz- and quartz-feldspar-phyric volcaniclastic rocks ± minor lavas (Grand Falls member), and aphyric, fine-grained volcaniclastic rocks (Little Falls member). The Flat Landing Brook Formation consists of aphyric rhyolite flows and interbedded pyroclastic rocks. Several gabbroic intrusions occur in both the footwall and hanging-wall sequences. These gabbros locally cut out the mineralized horizon at shallow levels, and are considered to be feeders to tholeiitic basaltic flows (Forty Mile Brook member) of the Flat Landing Brook Formation. The Flat Landing Brook deposit has many of the characteristics typical of volcanogenic massive sulfide deposits occurring within the highly productive Nepisiguit Falls Formation in the eastern part of the Bathurst Mining Camp. Mineralization occurs within or at the top of the Grand Falls member and comprises four or more massive to semi-massive sulfide lenses that vary in thickness between 3 and 5 m. Massive lenses are laterally gradational to, or underlain by, zones of disseminated sulfides up to 38 m thick. The deposit contains an estimated resource of 1.7 Mt grading 4.9% Zn, 0.94% Pb, and 19.54 g/t Ag to a depth of approximately 150 m. From 150 to 300 m below surface, mineralization is low grade and mostly disseminated. However, below 300 m, ore-grade (>10% Pb+Zn) massive sulfide lenses have been intersected over mineable widths. Oxide facies iron formation overlies and (or) grades laterally into the sulfide lenses. The oxide facies has strong positive Eu anomalies and gently sloping rare earth element (REE) profiles suggesting that it was formed from relatively hot acidic fluids that had interacted with felsic volcanic rocks in the footwall. In contrast, the silicate facies iron formation that is more distal to sulfide accumulations has very weak positive Eu anomalies and gently sloping REE profiles, suggesting either cooler hydrothermal fluids or dilution of the hydrothermal component by detrital material. Hydrothermal alteration has affected most footwall rocks. Most notably, albite-destructive alteration has resulted in Na2O depletion, whereas mass addition of K2O is manifested in the formation of sericite (white mica). In more intensely altered quartz- and feldspar-phyric volcaniclastic rocks of the Grand Falls member, feldspar destruction is accompanied by chlorite alteration, producing quartz-phyric rocks similar to those in the footwall of many Bathurst Camp deposits."

Jan 1, 2006

By Louis Frost

"1N 1951, the Dominion Steel and Coal Corporation, as part of a programme of modernization in their coal mining operations at Sydney Mines and Glace Bay, Nova Scotia, undertook the development of two large cross-measure tunnels, which were to be used for the purpose of raising the coal from the underground workings by conveyor belts direct to wash plants located on the surface.These tunnels were to reach from the surface to central loading points underground located at a depth of 600 and 900 feet, respectively. They were to be driven on a pitching gradient of 11 degrees to the horizontal, and they were to reach a length of 3,600 feet in the Sydney Mines area and 10,000 feet in the Glace Bay area.The longer tunnel, 19 feet in diameter, was driven a distance of 1,500 feet and, for domestic reasons, bas not yet been •completed. The other tunnel, in the Sydney Mines area, 18 feet in diameter, is steel supported and concreted throughout its entire length. This tunnel has been completed and will be in operation at an early date.The development of this particutar tunnel posed an additional problem, as the rock through which it had to pass was considered to be water-bearing. In the sinking of Princess Colliery shafts in 1866, a great deal of water had been encountered, and it had been necessary, while sinking, to line the shaft with cast-iron tubbing through the water-bearing strata. The shaft had to be lined for a depth of 300 feet at the upper end. It was anticipated that we would meet with difficulty in driving the tunnel through this strata."

Jan 1, 1955

By F. M. Clement

British Columbia, unlike the Prairie Provinces, cannot lay claim to vast prairies. She can, however, claim many valleys, uplands and plateaus that are capable of marked agricultural development. It has been said that British Columbia is not an agricultural province. This may or may not be true, but at the present time agricultural production in this province stands second only to that of forestry. The industry has advanced from a total production of 8 millions in 1908 to a total production of 60 millions in 1924, a total increase of approximately 650 per cent in 16 years. In the last 10 years production has increased from 30 millions to 60 millions. No other industry can point to such a rapid development. In 1908 British Columbia imported 12 million dollars worth of foods compared to the 8 millions which were produced at home. In 1924 she imported 20 million dollars worth of foods compared to the 60 millions worth produced at home. In addition we exported foods to the value of approximately 10 million dollars. British Columbia is therefore self-sufficing in-so-far as values ar.e concerned except for approximately 10 millions of dollars. It is not to be expected that this province will ever grow all the coarse grains that she may require: these, along with certain meats, will always be a heavy item in the imports. We are concerned at the present time more with the value of the products than with the quantities produced: in other words, with quantities only in-so-far as ? quantities improve value.

Jan 1, 1925

The JKRBT (JK Rotary Breakage Tester) is a newly developed impact breakage testing device for rapid ore breakage characterisation, and has recently been commercialised after a three year comprehensive validation study, involving five major mining companies and six industrialised JKRBT units deployed worldwide. Comparisons of breakage mechanisms and characterisation data between the JKRBT and the Drop Weight Tester (DWT) indicate that, despite the differences in the breakage modes, the JKRBT can provide statistically similar A*b parameters, by using a data reduction procedure which takes into account the difference in the number of contact points, strain rate and potential for secondary breakage. Feedback from the validation sponsors has indicated higher productivity and better repeatability of the JKRBT compared with the DWT. This better precision, combined with the JKRBT?s wider particle size capability and wider specific energy range, provide a more powerful tool, ideally suited to rapid mapping of ore hardness in geometallurgical and comminution applications.

Jan 1, 2012

By B. I. Whittington

This paper examines the effect of cation type (i.e. NH4+, Na+ and K+) and anion type (i.e. SO42- and C1-) on the extraction of nickel during the pressure acid leaching of a Western Australian laterite ore. The results are compared with testwork conducted with other Western Australian nickel laterite ores and the possible process implications of adding an additive to a plant autoclave are considered. Addition of either (NH4)2SO4, Na2SO4 or K2SO4 increased both the nickel extraction and the acid consumption, provided that the level of additive was not too great. For example, the nickel extraction of 93% increased to above 96% in the presence of additives, but decreased to 94% when, for example, NH4 levels increased from 7 kg/t ore to 21 kg/t ore. The relative stability of the jarosite species formed when additives were present influenced the amount of jarosite in the residue and, hence, both the final free acidity and overall nickel extraction. The use of Cl- versus SO42- salts as additives had little effect on overall nickel extraction or overall free acid values, although the presence of SO42- additives appeared to enhance nickel extraction kinetics over the first 60 minutes of the reaction. In contrast, manganese extraction was enhanced by the presence of Cl- additives.

Jan 1, 2004

By R. D. Brown

Higher employer costs and increased employee benefits will result from the current sweeping revisions of the un-employment insurance system now receiving consideration before Parliament. The new legislation, the Un-employment Insurance Act, 1971, will substantially increase the unemployment insurance costs of many employers through an increase in the level of employer contributions -generally, employer contributions will go to 1.4 times employee costs -as well as by extending coverage to many classes of employees now exempt. Under the new legislation, executives, technicians, teachers, institutional workers and others will be covered, and eligible for the higher benefits which it provides. For the first time, absence from work because of illness or accident may qualify individuals for unemployment insurance benefits.

Jan 1, 1971

By T. H. Patching, D. F. Coates

The Sub-Committee on Rock Classification, Canadian Advisory Committee on Rock Mechanics, has evolved a classification of rocks which should prove useful in studies of rock mechanics. Considered in two stages -actual rock substance and rock mass -the five-point classification involves the geological name of the rock, the rock strength and rock deformation, and, in the second stage, the gross homogeneity of the rock mass and the formation continuity.

Jan 1, 1968

By E. N. Gilje

"IntroductionDURING the past five years, over two miles of shaft sinking have been completed at Falconbridge. As sinking has continued, we have improved our equipment and technique with a resulting increase in efficiency. Throughout this period, all sinking has been done by contracting firms, under our direction and to our equipment specifications, with highly satisfactory results. Since 1949, Riddell shaft mucking machines have been successfully used in conjunction with the •benching method of sinking. Our most recent practice can best be illustrated by describing the method used in sinking No. 1 shaft at the Fecunis Lake mine.No. 1 Shaft, Fecunis Lake MineNo. 1 shaft, consisting of six compartments and measuring 13 ft. 11 l/2 in. by 19 ft. 9 3/8 in., outside timber (Figure 1), will be sunk to a depth of 4,170 feet. It was designed to accommodate two 10-ft.diam. Koepe hoists."

Jan 1, 1955

By D. Furrer, M. Dallaire

The arrival of Image analysis in the last 20 years has changed the world of quantitative metallography. Many standard measurement techniques which were previously manual can now be done with fully automated systems. This reduces subjectivity and operator fatigue and therefore enhances the quality of the statistical results. In many laboratories, Titanium Alloy microstructures continue to be evaluated by traditional methods, where quality of results is subject to operator fatigue and level of experience. Advances in Camera technology have tremendously improved image acquisition. One can often see clearly at 500x what can not be observed at 1000x, allowing for a larger area to be analyzed, without the inconveniences associated with very high magnification objectives. Powerful and versatile Image analysis software combined with a high precision motorized stage gives access to a multitude of applications, which were extremely challenging or impossible until now. Image Analysis tools such as Multilayer Grab, which reconstructs an uneven image into one plane of focus (ex. Observation at high magnification of texture resulting from etching) and Mosaic which builds an image from a number of fields of view (ex. Reconstruction of very large grains at low magnifications) expand even further the power and flexibility of IA systems. This presentation will describe how automated methods are applied to the point count method and grain size measurement. We will show how cameras and software work together to permit quantitative measurements of primary alpha and prior beta microstructures, as well as lamellar alpha plate thickness in titanium alloys.Automated and semi automated quantitative measurements of various Titanium microstrures have been assessed, using the Clemex Vision PE. Examples of the methods and steps used are presented.

Jan 1, 2006