Search Documents

By H. F. Naldrett

"AbstractAt the end of May, 1950, Imperial Oil, Limited, had completed a total of 192 D-3 wells in the Leduc-Woodbend field, 62 of which lost circulation in the D-3 zone for periods ranging from two hours to fifty days. The majority of the remaining wells •lost some mud without actual loss of returns. In addition, independent operators completed 69 D-3 wells, of which 9 lost circulation. Included among the latter is the now well known Atlantic No. 3 well, which blew wild out of control for seven months. The well was finally brought under control through two directionally drilled wells, but not before the derrick fell and the well caught fire. Practically all known filler materials have been used in attempt3 to prevent or regain loss of circulation, but none has been successful, except in minor cases. Ordinary sawdust has come to be the most commonly used filler material and is added to the mud before the D-3 zone is contacted. In cases of serious loss of circulation, the on1y successful method of getting returns has been the use of a series of small cement plugs.IntroductionThe Leduc field is twenty miles southwest of Edmonton, Alberta. Geologically, it is on the east limb of the Alberta syncline, in the homoclinal belt. The main productive zones are in the Upper Devonian formation and are known locally as the D-2 zone and D-3 zone, respectively (see Figure 1).The D-3 zone is a dolomitized reef with fair average porosity and permeability, and shows considerable evidence of vertical fracturing. Porosity is mainly due to moderately uniform development of vugs which are interconnected by small crevices. However, the formation is known to be, locally, extremely vuggy and in places cavernous. These latter conditions create very serious drilling problems due to the hazard of loss of circulation, particularly in the gas cap, which has a maximum thickness of 200 feet. The D-3 zone is contacted at an average depth of 5,300 feet."

Jan 1, 1950

By S. S. Dimov, B. R. Hare

This paper describes two micro-beam analytical techniques(Dynamic SIMS and TOF-SIMS) which have become an intricate part of a comprehensive analytical approach for precious metal (PM) ore characterization and process mineralogy or deportment studies. The value of the D-SIMS technique is its capacity for accurate analysis in the sub ppm range along with the ability to produce high resolution elemental maps. The TOF-SIMS is significant for speciating and quantifying preg-robbed Au on the surface of carbonaceous material. In combination with traditional assays, the two techniques can provide invaluable information regarding the distribution of PMs within an ore along with providing insight into potential sources of PM loss in processing or where losses have occurred in process streams.

Jan 1, 2011

By B. M. Currell, M. J. Neate, P. W. Bowden

Historically the hydrogen fluoride laden fume emitted from the electrolytic cells in the aluminium reduction process is further treated in pulse jet dust collectors. These dust collectors act as dry scrubbers performing two duties: adsorbing the gaseous fluoride emitted from the cells onto alumina dust; and collecting the alumina dust minimising particulate and fluoride emissions to the environment.Patented StarBag (TM) technology has been used in aluminium smelters in Australia as a means of increasing the dust collection and fluoride scrubbing capacity of existing collectors. This technology provides an alternative to major capital equipment upgrade where increased capacity is required, and potentially lowers the production cost per tonne of aluminium where capacity limitations are being realised and production expansion is required. This paper presents the findings of on-site pilot scale, and full production scale comparative tests, highlighting the operational and variable differences observed utilising the Star-Bag(TM) technology at Boyne Smelters Ltd in Australia. The results illustrate how this technology can be utilised to increase the hydrogen fluoride scrubbing efficiency and dust collection capacity of existing capital equipment.

Jan 1, 2006

"In developing a backfill system handling tailings feed to and from the storage silo, it is necessary to establish a slurry laboratory to develop the technology and silo design criteria. This paper presents the principles involved in such development and the importance of testing principles for optimizing the slurry system. Evaluation procedure based on experiments is applicable to a wide range of materials and allows silo design by scaling up the data gained from model tests. Silo simulation has been successful to design and operation, so becomes an effective approach to backfill applications. IntroductionThe silo is a device comprising specialized equipment and operating with related procedures for storing and handling the mill rejects as backfill slurry. It provides a steady supply of the solids slurry, prepared at desired pulp density under the continuous feed conditions. Because the silo system is designed to accomplish specific objectives when dealing with a particular mill tailings slurry, it is necessary to characterize certain slurry properties, behaviour of the solids slurry and understand the silo performance to establish design criteria. Bench-scale, pilot-scale and dewafull- scale experiments were employed in developing the load-storage-discharge system, and routine procedures are now available for pre-design testing. Silo model experiments and full-scale tests were conducted to define the design parameters and evaluate the silo performance. A silo can be designed by scaling up the silo model geometry and data obtained during tests.Since the early 1960s, silo backfill systems have been widely established. The shape and size of the silo and the operation procedure, as practised, all appear to be relevant to successful operation. Understanding the basic material properties and behaviour of solids slurry retained in the silo will help perfect the silo design, operation procedure and, consequently, improve the silo performance."

Jan 1, 1997

By C. J. Edmonds, R. Bland, W. C. Ferguson, R. Whitehead

"In 1969, the Environmental Science Division of James F. MacLaren Limited received authorization from The International Nickel Company of Canada, Limited to carry out a water quality monitoring program in the Lake Shebandowan region of Ontario, where a new base metal mining and milling complex was expected to go into operation in 1972. The objective of the program is to establish base-line water quality characteristics. Fully realizing their corporate responsibility to minimize the effects of the proposed activities on the environment, Inco decided that it would be desirable to establish a program by which any change in the quality of environmental waters will be detected before detrimental conditions ensue, permitting prompt corrective measures to be taken. The program has been in progress for over two years. The waters are sampled and analyzed four to six times per year. Sampling stations are located in Lake Shebandowan and on the adjacent Gold Creek - Matawin River system. On-site analyses and measurements are made of flow, dissolved oxygen, temperature and pH. Samples also are collected for later analysis in the laboratory. These samples are analyzed for a wide range of chemical and biological characteristics. The paper discusses the extent of the sampling program, the techniques utilized and the value of such programs in maintaining the quality of the environment."

Jan 1, 1973

By W. van der Merwe

With the gold industry looking to process more complex ores, the online measurement and control of cyanide addition to the gold leaching circuit has become more crucial. This paper compares the two commonly employed "free" cyanide online analysis methods (amperometric and potentiometric end-point silver nitrate titration) with the common site laboratory rhodanine endpoint silver nitrate titration and ion selective electrode methods. Measurement differences between these methods are presented and discussed for cyanide solutions containing copper and zinc with varying cyanide to metal ion ratios. The resulting cyanide available to leach gold is also compared with these measurements.

Jan 1, 2011

By N. R. Andrade-Gonzalez

The present work was performed on four alloys containing Al-6 2 wt pct Si-3 5 wt pet Cu, with magnesium in the range of 0.02-0 40 wt pct, and strontium in the range of 0-165 p p m Tensile bars were cast in a permanent mold (ASTM B108-160) and heat treated at 495°C for 4 hours, followed by quenching in hot water. Two different artificial aging temperatures were applied at 180 °C and 220 °C for times from 0 5 h up to 8 h Tests were conducted with the intent of determining how the mechanical properties of an aluminum-based 319 alloy are affected when aging time and temperatures are varied In general, it is seen that the alloy does not exhibit the common peak-overaged aging condition due to the presence of several coexisting phases, indicating that they form through complex eutectic reactions late in solidification.

Jan 1, 2004

By W. A. Bain

"AbstractProduction from the Excelsior Reservoir has amounted to approximately one million barrels. This production has caused a 'Pressure •drop of 10 p.s.i. from the original pressure of 1,245 p.s.i.g. Volumetric balance calculations indicate that the pool as being produced by a water drive whose strength is •probably unsurpassed in Western Canada. It has also been shown by 'unsteady state' calculations that the reservoir will still be above the saturation pressure of 915 p.s.i.g. at the time of depletion. The average permeability of the producing formation is approximately 1,000 millidarcys and, consequently, well draw-downs are very low. The field is essentially a bottom-water drive and calculations have shown that gravity drainage will greatly assist the recovery of oil. Water flooding data on several cores •have placed the flushing efficiency at •approximately 50 per cent, which indicates a recoverable oil-in-place of 17.7 million stock tank barrels. Calculations and field data indicate that the MER for the early life of this field is probably as high as 8,000 to 10,000 stock tank barrels per day.IntroductionTHE EXCELSIOR NISKU oil reservoir is located about twenty miles northeast of Edmonton. The field was discovered in November, 1949, by Imperial Excelsior N.o.1 well, in Lsd. 13, Sec. 3, Twp. 56, R. 22, W. 4, at a depth of 3,850 feet.Since discovery, development has continued on a 40~acre spacing pattern. At the end of 1951, drilling over approximately 80 per cent of the estimated productive area of 1,680 acres had established 32 we1ls capable •of production. The field •has been fairly well delineated by dry holes on all but the eastern flank ."

Jan 1, 1952

By C. W. Davis

AN inclined shaft is usually more difficult to sink than a vertical shaft, yet it is often chosen because of the subsequent saving in cross-cuts required to reach an inclined ore body. This paper briefly discusses the factors which led to the choice of an incline and then describes the operations involved in the preparatory work and in the sinking. These operations included a programme of mining out the underground facilities and installing the structures required for a hoist-room, cable-raise, waste-pass, ore pass, two sets of skip dumps, and a collar station equipped with counterbalanced drop-rails. The shaft was sunk 1,000 feet and four stations were cut, each with loading pockets. As the sinking progressed, the rock changed from hard porphyries and dense cherts to blocky limestones and earthy rubble. These conditions called for a change in methods and it is to the red it of the shaft-sinking crew that they overcame the new difficulties as the shaft progressed, while maintaining a satisfactory monthly advance. The section mined out was nine feet six inches by seventeen feet overall. This gave room for three compartments: two skip compartments four feet three inches by five feet nine inches inside the timber, to handle two-ton skips, and a manway three feet six inches by five feet nine inches. The sinking began on December 16th, 1941, and was completed on February 15th, 1943.

Jan 1, 1945

By T. Takayama Filho

Votorantim Metais Zinco is a smelting facility which produces SHG zinc, zinc alloys, sulfuric acid, liquid SO2, copper sulfate, cadmium metal and silver concentrate. It is located at Juiz de Fora, Minas Gerais State, Brazil. This facility has been operating since 1980 and its current capacity is 95,000 tonnes of zinc per year, using mostly imported sulfide concentrates.The plant uses the conventional roast-leach electrowinning (RLE) process, in which iron is removed from the circuit as jarosite. The residues generated by the RLE process, which amount to about 200 t/day (dry weight), were until 10 years ago, deposited in tailing ponds having no impervious lining. More recently, jarosite and other wastes have been deposited in a properly built reservoir, but this is reaching its maximum capacity. In order to decommission these disposal operations and to reclaim the sites in an environmentally acceptable manner, Votorantim Metais concluded in 2004 a rehabilitation project for the old tailings pond and prepared detailed plans for managing the current and future disposal of jarosite-bearing residues. This paper describes the procedure for removing iron from the hydrometallurgical circuit and discusses the past and current status of the residue disposal sites, as well as the future challenges related to the environmentally acceptable handling of iron residues.

Jan 1, 2006

By W. J. Taylor, T. D. Parris

"Over 90,000 feet of raise have been bored at International Nickel underground mining operations throughout the Sudbury District since the advent of raise boring in the early part of July, 1964. With a total of 10 raise borers on hand at this time, techniques have improved steadily since introduction at INCO mines. The first unit, designed for use in rock of low compressive strength, had to be modified and redesigned to cope with Sudbury Area Precambrian rock. As equipment and boring techniques improved, a specially designed machine for larger holes was developed and is now in use. More powerful units, with a thrust capacity of up to 750,000 pounds, are under investigation. Raises have been bored up to 84-inch diameter, and the changeover to 5- and 6-foot flat reaming heads with improved cutter design has increased performance substantially. As a result, 5-foot-diameter raises have been completed to a length of 750 feet and 6- and 7-foot raises to over 500 feet. Reference is also made to the drilling of over 23,000 feet of drainage and sand-fill holes, ranging up to 7% inches in diameter, with smaller underground rotary drill equipment.Finally, a look into the future indicates the need for further improvements in equipment design to permit economic boring of 7- to 8-foot-diameter raises in Sudbury Area ground types."

Jan 1, 1972

By W. W. Bake

INTRODUCTION IN IN JUNE, 1943, the main pillars of the Beattie Mine glory hole failed, allowing over a million yards of wet clay and debris to flow into the mine, completely filling all workings to within seventy feet of the 3rd level. The resulting Job of clearing these workings and rehabilitating the mine represents a unique and hazardous operation, seldom, if ever, previously encountered in Canadian mining. The purpose of this paper is to describe one phase of this operation -that of cleaning and rehabilitating the mine from the 6th to the 9th level -to outline briefly the events which led up to this work and to describe the techniques and costs involved. It will be noted that such costs, methods, and performance figures as are dealt with in this paper refer only to work in the internal shaft and adjoining workings from the 6th to the 9th level, previous work having been done under other supervision and management. The Beattie mine is in Duparquet township, northwestern Quebec, twenty miles northwest of the town of Noranda and twenty-three miles southeast of the town of La Sarre. The mine and the town of Duparquet, which it?supports, are accessible by highway from Noranda throughout the year. Production at the Beattie mine began in May, 1933, and up to June, 1943, twenty-one million dollars in gold and silver had been recovered from five and a half million tons of ore.

Jan 1, 1951

By J. McCreedy

"The addition of Portland cement to hydraulic sand fill has resulted in the production of stable and self-supporting cemented sand fill. The use of cemented fill in the mines of The International Nickel Company has resulted in substantial economies in timber requirements, de-creased dilution of ore and greater flexibility in mining methods.Coupled with special mining techniques, it has permit-ted mining by both cut-and-fill and shrinkage stoping methods to much greater depths than heretofore. The use of cemented sand fill has permitted revisions to undercut-and-fill mining which have significantly improved the efficiency of this method.Automated mixing systems have been developed for preparing cemented sand fill in surface sand plants on a continuous throughput basis. Control of cement-sand mixtures is obtained by the use of a mass flow measuring system and weighing cement feeders."

Jan 1, 1966

By I. Filzwieser, A. Filzwieser

The Peirce Smith converter is the key metallurgical vessel in the majority of copper smelters. During the two step process, oxygen enriched air is injected through a row of tuyeres into the matte received from a primary smelting unit. Additionally, in the first step the iron content is oxidized into a fayalite slag by the addition of silica. During the second step, the remaining copper sulphide is converted into blister copper with a final sulphur content of approximately 200 ppm. The overall efficiency of this process is determined by the total reaction time, the slag quality and quantity, and the chemistry of the final blister copper. To increase the reaction kinetics during both stages, the METTOP Process Control and Regulation (MPCR) system was developed, which consists of four elements: OPC - Optical product control ACR - Automatic computer regulation GCU - Gas control unit GIS - Gas injection system The OPC system from SEMTECH records the optical spectrum emitted by the off gas flame providing immediate, detailed process information. Using this online data, additional gas can be automatically injected into the converter through a gas injection system opposite the tuyere zone. An improved oxygen distribution in the melt and the accurate determination of the process end point results in a significant reduction in the process cycle time. Furthermore, by maintaining the reaction closer to the equilibrium the final sulphur and oxygen content can be reduced compared to the conventional process. In particular, the final sulphur content can be lower than 70 ppm, eliminating the need for an oxidation step in the anode furnace.

Jan 1, 2007

By Jerry Gagnon, Matt Burr, Timothy Ellis, Abbas Mirza, Larry Webb

"The mechanical properties of RSR anode alloys (lead-calcium-tin, 009+ and lead-strontium-tin) were investigated as a function of time with an objective of developing lead anodes for use in high temperature electrolytic processes such as in copper liberator cells and in cobalt and nickel electrowinning. At a temperature of 70 oC, the mechanical properties of rolled RSR lead-calcium-tin (PbCaSn) alloy currently used in copper electrowinning decreased gradually while the mechanical properties of rolled RSR lead-strontium-tin (PbSrSn) decreased relatively quickly and stabilized at low strength levels. Cast PbSrSn started off as the weakest alloy but its properties remained stable with time. Rolled RSR 009+ anode alloy showed improvement in ageing properties over the other alloys tested. However, its mechanical properties did not stabilize in the study timeframe of 284 days. Further investigations are planned to study the effect of alloying elements on mechanical properties of RSR 009+ anode alloy over several years as a function of time at 70 oC. The mechanical properties will be evaluated to determine the time at which they stabilize. Comparative plant trials with rolled RSR PbCaSn and RSR 009+ will also be performed in copper liberator cells and in cobalt and nickel electrowinning tankhouses to determine their mechanical and electrochemical performance at temperatures of 65-75 oC.INTRODUCTIONLead-based alloys are the primary anodes used in the electrowinning of copper, zinc, nickel, cobalt and manganese from sulfate-based aqueous systems. Lead anode technology has evolved over the years migrating from pure lead and lead-antimonial alloys to the present day PbCaSn alloys for copper and PbAg and PbCaAg alloys for zinc electrowinning (Prengaman, Ellis and Mirza, 2010). It has also migrated from cast to rolled microstructures in search of improved mechanical properties and higher corrosion resistance. Although great strides have been made in the development of new lead anode alloys and production processes for lead anodes to be used in copper electrowinning, the industry still has some unresolved issues. These relate to the necessity of having higher mechanical properties especially for the lead anodes in liberator cells in copper electrorefining and for cobalt and nickel electrowinning as these tankhouses operate at temperatures of 65-75 oC compared to 40-45 oC in case of copper electrowinning."

Jan 1, 2016

By A. van As, J. McGaughey, M. J. Mol, R. Tosen

Geotechnical monitoring is a key element of the successful management of a block cave mine. The interrelationships between production and various monitoring datasets are often not realized due to a lack of data integration and appropriate 3D visualization. Timely delivery of information to ensure best cave management practices is only possible with an integrated cave management system. At Rio Tinto, a state-of-the-art cave management system (CaveCAD) has been designed and developed in cooperation with Mira Geoscience to integrate and analyze vast datasets and report this as instructive information regarding the current \u201cstatus\u201d of the cave.

Jan 1, 2014

By D. F. VanDine

The phases of a typical exploration program for sand and gravel resources include: (1) collection and assessment of existing information; (2) air photo interpretation and remote sensing; (3) ground investigation and mapping; (4) sampling and testing; and (5) data storage, retrieval, analysis and presentation. Depending on the purpose, time frame and funding available for the study, these phases, and the various techniques used within each phase, will vary. Once a sand and gravel deposit has been located, defined in size and quality, and found to be suitable for a given purpose, it can then be classified as a granular resource.

Jan 1, 1984

By C. J. Havard, G. C. Taylor, D. G. Cook, N. C. Ollerenshaw, D. K. Norris

"The area encompassed by this report is the eastern and northern Cordillera, shown on the composite map accompanying these background papers. It extends from the 49th pm•allel to the Arctic Ocean and from the Rocky Mountain and Tintina trenches to the Interior Plains. The Mackenzie delta is included in the discussions because of the implications of the bedrock geology of the Arctic Plateau and Coastal Plain on the hydrocarbon and mineral potential beneath it.The eastern and northern Cordillera forms the back-bone of the Western Canada sedimentary basin and from it most of the principles of orogenesis and epeirogenesis relating to the understanding of the structural, depositional and fossil record of the basin have been derived. It may be divided roughly into two parts, reflecting basic differences not only in structural style but also in mineral potential. The more easterly and younger rocks generally contain hydro-carbons, coal and non-metallic minerals; the more westerly and older rocks contain metallic and industrial minerals."

Jan 1, 1970

By D. Pawelus, J. Butra, R. Debkowski, M. Szpak

Impact of horizontal stresses on stability of underground workings in mines is a very important issue in underground mining. Identification of the initial state of stress in the rock-mass should be one of the main actions taken into account while designing and carrying out the mining activity in underground mines. The paper presents the tests on three dimensional stress pattern in Polish copper mines, owned by KGHM Polska Miedz S.A. Group, carried out in 2012. The research program covered 7 measuring stands in two mines; their average depth was about 1000 m. The main aim was to identify the values and directions of horizontal stresses in order to optimize the extraction and to improve the safety. The overcoring method with the use of CSIRO HI type probe was applied. The paper also describes the measuring technique which was developed for the purpose of specific mining and geological conditions of KGHM mines, taking into consideration the natural hazards encountered there as well as technical and operational capabilities with regard to drilling equipment. The experience gained during the underground measurements and the issue of making such measurements in underground copper mines in Poland are presented in the paper. The stress patterns obtained during the underground measurements are of application importance for the process of designing the spacing of mine workings and improving their stability and mine support selection.

Jan 1, 2015

By E. Wolmarans

The selection of the main mineralised zone (MMZ) concentrator milling circuit has followed a comprehensive route over the preceding 10 years. Many knowledgeable parties have contributed and assisted in developing the milling circuit according to the best available information. The final selection of the flow sheet was completed after DRA conducted a techno-economic study on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous (AG) milling. The results from all the above mentioned work indicated that it is possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding circuit. The flow sheet was designed to treat the main mineralised zone (MMZ) arising?s from both underground and open cast operations and incorporates a fully autogenous grinding (AG) circuit. Commissioning of the 375ktpm concentrator at Nkomati Nickel began in August 2009 with the first ore reporting to the mill on the 15th of September 2009.

Jan 1, 2012