Search Documents

By P. G. Hallof

The exploration staff of Campbell-Chibougamau Mines Limited has used past experience to delineate several areas of geologic interest under Lake. Chibougamau. Du• ring the winter of 1964-65, a reconnaissance induced polarization survey was carried out on the lake. First, several lines were surveyed over the known mu1.erahza-tion at the Henderson mine; the grid was then extended into the areas of interest. Several anomalous zones were located and drilled; one, of these proved to be of economic interest.

Jan 1, 1967

By D. Tao

Froth flotation is widely used in the coal industry to clean -28 mesh or -100 mesh fine coal. A successful recovery of particles by flotation depends on efficient particle-bubble collision and attachment with minimal subsequent particle detachment from bubble. Flotation is effective in a narrow size range outside which the flotation efficiency drops sharply. A fundamental analysis has shown that use of picobubbles can significantly improve the flotation recovery of particles by increasing the probability of collision and attachment and reducing the probability of detachment. A specially designed column with a picobubble generator has been developed for enhanced recovery of fine coal particles. Picobubbles were produced based on the hydrodynamic cavitation principle. Experimental results with one metallurgical coal and one steam coal have shown that the use of picobubbles in a 2" column flotation increased fine coal recovery by 10-30%, depending on the feed rate, collector dosage, and other flotation conditions. Picobubbles also acted as a secondary collector and reduced the collector dosage by one third to one half.

Jan 1, 2006

By A. F. Abd El-Rehim

The behavior of both transient and steady state creep of Al-4.5 wt% Cu and Al-4.5 wt% Cu-0.1 wt% In alloys was investigated using a constant stress where torsional oscillations of different frequencies and shear strain amplitudes were operated at various working temperatures. An augment in both transient and steady state creep rates was observed by increasing both frequency and shear strain amplitude of the applied oscillations. The mean values of the activation energy of both alloys for both creep stages were found to be equal to that quoted for dislocation intersection mechanism.

Jan 1, 2006

By B. S. Ignasiak, B. N. Nandi, D. S. Montgomery

The growing need to measure the extent of weathering of coking coal in storage and in transit prompted the comparison of the dilatation of coking coal on heating, which is known to be a sensitive index of oxidation, with the composition and volume of the gases produced by a mild pyrolysis of the same coal. It was found that the pyrolysis method had the advantage in that it could be used to study coking coals in advanced stages of oxidation, when the swelling properties had been largely destroyed. Of the various constituents in the pyrolysis gas, the most sensitive indication of coal oxidation was the volume of carbon monoxide evolved per gram of coal. For the coals examined, this index appeared to be at its best when the temperature of pyrolysis was approximately 35oC.

Jan 1, 1970

By H. M. Woodrooffe

IT IS WELL KNOWN that chrysotile asbestos from various occurrences exhibits varied physical properties and certain differences in chemical corn position, both of which conditions may have an important bearing on the industrial utilization of the fibre. The usefulness of a harsh fibre in the manufacture of asbestos cement products and of low-iron fibre for certain electrical uses are examples. It is also .possible to obtain a fibre with a texture too harsh and brittle to be of economic value. Much research into the structure of the mineral and to a lesser degree observations relating the water of combination to certain physical properties have ?been reported. This paper is an attempt to show that the pyrolysis of ?chrysotile takes place in three stages and that the conditions of pyrolysis are peculiar to the fibre and may afford some clue to the variations in physical properties of asbestos fibres which affect their utilization.

Jan 1, 1956

By M. Desjardins

The Hoyle Pond underground mine, located in the Porcupine Gold Camp, east of the city of Timmins, Ontario, Canada, is the cornerstone of Goldcorp Canada Ltd?s Porcupine Gold Mines. Cut and fill, shrinkage, longhole and panel mining methods are employed to excavate the narrow gold bearing structures. In order to meet increased flow requirements of 256 m3/s at the mine, a new Fresh Air Raise (FAR) and new surface fans were commissioned in early 2005. The newly acquired fans were capable of supplying the desired volume of air within a range of 1.5 and 2.0 kPa. Upon commissioning of the surface fans the total pressure was found to be exceedingly high; far beyond the design capabilities of the new installation. Consequently only one surface fan could be operated at any given time providing about half the required volume of air. Extensive work was immediately started aimed at reducing the system resistance in order to permit operation of the two fans in parallel and achieve the required mine flows. Larger booster fans were installed in parallel at the 900 m level, a 3 m raise bore linking the 450 and 900 m levels was developed to twin the existing fresh air circuit, and the FAR from surface to the 450 m level was twinned with the original FAR. This strategy, completed in 2012, resulted in a drastic reduction in system resistance and pressures, allowing the two surface fresh air fans to be safely operated in parallel and meeting the flow requirements. This paper describes details of the engineering design work and commissioning of the modified ventilation system, successfully ensuring the long term viability of the project.

Aug 1, 2013

By Edouard Asselin, Tasawar Javed

This study was conducted as a part of ongoing work to characterize sulphide concentrate leach residues generated under CESL (Cominco Engineering Services Limited) and Vale pilot and demonstration plant medium temperature (150 °C) process conditions. Three different samples were analyzed. Derivative samples were prepared by extracting gypsum, sulphur and amorphous/poorly crystalline iron oxyhydroxide phases from the leach residues. Thermal behavior of the samples was studied by thermal gravimetric analysis (TGA) and differential thermal analysis (DTA) in the temperature range 25 to 800 °C in both air and nitrogen atmospheres, with XRD analyses both before and after heating. Thermal transformation temperatures for different iron oxides/oxyhydroxides present in hydrometallurgical leach residues vary over a wide range which suggests the variable crystallinity of the phases. Raman spectroscopic analysis was carried out to help identify the type of iron phases in the residues. Furthermore, hydroxylamine hydrochloride (HaHC) and oxalate extractions were used to compare the fractionation of the amorphous/poorly crystalline iron phases in the residues. Given the compositions of the residues, any thermal events in the temperature range of 200 °C to 480 °C were attributed to amorphous/poorly crystalline iron phases.

Jan 1, 2014

By K. Tarr

Acid-producing mine tailings are present at many active and inactive mine sites and pose an environmental liability due to the potential for acid rock drainage. Acid rock drainage originating from a tailings pile, a waste rock pile, or exposed sulfide-rich rock, can cause discoloration and turbidity in receiving waters, and the loading of ions mobilized by the acid can cause a decrease in aquatic flora and fauna, and reduction in the quality of groundwater. The primary cause of acid generation is the oxidation of sulfide minerals, predominantly pyrite and pyrrhotite. Considerable mine tailings are being stored on surface in vast tailings impoundment areas across Canada. In the tailings within this study, from the Sudbury, Ontario area, the sulfide mineral of primary concern with respect to acid generation is pyrrhotite. Different tailings types show varying and progressive degrees of oxidation correlating to their specific sulfur contents. The degree of oxidation is determined by the relative extent to which the sulfides have reacted as well as the depth of oxidation within the tailings. Natural Resources Canada, CanmetMINING is dedicated to research supporting the Green Mining Initiative, a program reducing business risks by demonstrating practices that reduce environmental impacts. In cooperation with the Canada Mining Innovation Council (CMIC), applied research aims to reduce land disturbance, waste volumes, and releases to the environment. By reutilizing tailings from vast impoundment areas as a component in backfill, the potential environmental impact would be lessened considerably, due to the reduced tonnage stored on surface long-term. From an operating perspective, there is a need for supplemental feed for backfill from time to time. The reclamation of old tailings for use in backfill is also driven by the fact that old tailings ponds may not be structurally stable, and it may be more cost effective to remove the tailings than to upgrade the impoundment structure. However it is imperative that these old tailings be fully characterized to determine their suitability for use underground, in order to ensure the long-term integrity of the resulting backfill matrix. A study was conducted to investigate the feasibility of tailings reclamation from old impoundment areas as a significant component in backfill. The materials were first physically and chemically characterized, followed by preparation of samples to determine optimal mix proportions for strength development for both paste and hydraulic fill compliance. It was found that the amount of oxidized tailings included in the backfill material had a profound effect on both the segregation and settling properties of the backfill matrix, as well as the mechanical properties of the samples. The strategies for decision-making, based on the criteria for material characterization, mining plan, and cost effectiveness are discussed.

Aug 1, 2013

By H. Son

The three-dimensional (3D) reconstruction of as-built industrial plant models plays an important role in revamping planning, maintenance planning, and preparation for dismantling during the lifecycle of industrial plants. Recently, the 3D reconstruction of existing industrial plants was conducted using laserscan data to make surveying processes more efficient. However, the current 3D reconstruction process from laser-scan data is still limited due to the need for significant human assistance. Although a great deal of effort has been made to efficiently reconstruct 3D as-built industrial plant models, the presence of objects?such as equipment, pipelines, and valves of different sizes and shapes?in existing industrial plants significantly increases the complexity of laser-scan data and makes automating the reconstruction process more challenging in practice. The purpose of this study is to propose a knowledge-based approach for the 3D reconstruction of as-built industrial plant models from unstructured laser-scan data. First, pipelines were extracted from laser-scan data based on surface curvature information and knowledge about pipelines' sizes from existing piping and instrumentation diagrams (P&ID). Once entire pipelines were extracted, they were modeled based on skeleton features. Then, the remaining objects were clustered and grouped separately via the region grouping process. Afterward, clustered objects were retrieved and modeled based on global feature-based matching from the 3D database. Finally, the resulting model was checked to ensure that it was well-reconstructed according to the information regarding the relationships among objects abstracted from the existing P&ID. The preliminary results on actual industrial plants show that integrating knowledge into the reconstruction steps played an important role in the proposed approach and that this approach obtained accurate as-built industrial plant models from unstructured laser-scan data. The proposed approach could be successfully utilized to assist in many applications during the lifecycle of industrial plants.

Aug 1, 2013

By J. D. Bosman, L. J. Gardner

"The Bushveld Complex is a large layered igneous intrusion, located in the northern parts of the Republic of South Africa. The complex hosts the largest known reserves of Platinum Group Metals in the world. On the western limb of the complex, mining of the Merensky economic horizon and UG2 chromitite layer has been conducted for many years by several mining companies, including Impala Platinum Limited. Over the past decade, Impala has planned a new generation of greenfield vertical shafts, commencing with comprehensive geological and geotechnical studies. As part of the geotechnical studies, numerous tests have been conducted to quantify the mechanical properties of the various near-reef rock types. These tests include point load tests conducted in the field, as well as uni-axial compressive strength, triaxial compressive strength, and Brazilian disc tensile strength tests conducted in specialist laboratories. The authors have compiled an extensive database containing a large number of tests for different rock types, ranging from felsic Anorthosite to mafic Pegmatoid. The database was analysed to quantify the mechanical properties and values for Mohr Coulomb and Hoek Brown failure criteria for each rock type typically exposed by mining. The paper will provide a data set of rock mechanical properties typically used in numerical modelling and other design processes. Using the significant number of tests available, data describing the variability of the various parameters will be included."

Jan 1, 2015

By S. S. Al-Thyabat, A. M. Ghrair

"Printed circuit board (PCB) is the main part of any electric or electronic device, providing mechanical support and electric connection for the board eclectic components such as capacitors, resistors, diodes etc. PCB consists of non-conductive substrate overlaid with one or more layers of copper sheets. They also contain appreciable amounts of base metals (copper, nickel, tine, and aluminum) and precious metals (gold, silver, and rare earth elements (REE)) which end up in the landfill at the PCB end-of-life.PCB recycling E-waste in general is a profitable business; many valuable raw materials, precious and base metals, can be extracted with high purity. Approximately, one metric tonne of PCBs may contain 80-1500 g of gold and 160–210 kg of copper. The precious metals recovered from PCBs occur at concentrations higher than commercially mined minerals. Also PCB recycling is very important to our environment since many heavy metals (e.g. lead) may be leached from the landfills to the underground reservoirs. In Jordan, however, the work conducted on E-waste and PCB recycling in particular is limited; currently most of the E-waste is either exported or dumped in the landfill.In this work, a combination of physical (magnetic separation), physicochemical (flotation), and chemical methods (leaching) were used to compare metals concentrations in leach liquors produced from a concentrates resulted from a combination of these methods. It was found the leach liquor of the magnetic fraction of the PCB coarse size gave the highest concentration of Fe, Al, and Ni while concentration of Cu was higher in leach liquor of nonmagnetic sink fraction. On the other hand, metals concentration almost similar for both sink and float of the fine size fractions, indicating even distribution of metals concentrations in the fine size fractions."

Jan 1, 2016

By H. J. McQueen

Friction stir welding (FSW) generates complex microstructures in the nugget and thermomechamically affected zones (TMAZ) that have led to diverse explanations. However, consideration as an extension of microstructure development in piercing/extrusion can lead to a better understanding of flow patterns and microstructures during FSW. Furthermore, the intense strains in the nugget/TMAZ can be interpreted by comparison with ultra-high strains in torsion that exhibit dynamic recovery as extending into regions with high angle boundaries strongly serrated with spacing near the subgrain size defined by the high temperature. The subgrain diameter and extrusion pressure have been shown to be dependent on the Zener-Hollomon parameter Z (=t exp(Q/RT), Q activation energy, R gas constant) combining temperature T and strain rate E in the same mariner as for torsion and compression. Moreover, such tests exhibited steady state stress os above a certain strain Es (rising as Z increases) in which T, , subgrain diameter and dislocation spacing remain constant. Due to the subgrain boundaries (SGB, low angle <5°, i.e.,LAB), continually rearranging by migration, decomposition and reformation, the subgrains remain equiaxed in elongating grains, whose boundaries (GB) become serrated as they migrate to absorb SGB. As confirmed by straining in torsion at constant T and Z. , more subgrains bordering the greater GB area have several high-angle facets (HAB) ; these small cellular regions with a mixture of HAB and LAB facets are designated HAB-subgrains. As serrations in neighboring grain boundaries impinge, the grains pinch off becoming shorter; this occurs at higher strains as subgrain size decreases with rising Z. The pinching-off makes the neighbors thicker so the grains never become thinner than about two subgrain diameters. In conjunction with such geometric dynamic recrystallization (gDRX), GB&apos;s undergo a net migration into grains with denser substructure, enlarging those with larger subgrains. Consequently a better name has been proposed: grain dimensioning dynamic recovery (gDRV).

Jan 1, 2007

By Rodolfo Zanella

Au/TiO2 catalysts prepared by deposition-precipitation with NaOH (DPN) (~3 wt%) and urea (DPU) (~8 wt%) were tested in crotonaldehyde hydrogenation at atmospheric pressure. There is no differences in activity (mole.gAu -1 s-1) and selectivity between both DPU and DPN samples for a given activation treatment. This is due to the fact that DPU and DPN samples exhibit similar gold particle size distribution, although the gold loading in DPU is much higher that in DPN. The DPU samples were reduced under H2 at different temperatures (120-500 °C) or under air at 300 °C with various flow rates, to vary the average particle size within a large range, 1.7 to 8.7 nm. The selectivity to crotyl alcohol (selective hydrogenation of the carbonyl bond) is high, 60-70 %, and almost constant as a function of the particle size. The selectivity to crotyl alcohol is also constant for conversions between 10 and 50%. These results suggest that the adsorption mode of crotonaldehyde is of ?3 or ?4-type. In contrast, the TOF depends on the gold particle size, it drastically increases when the gold particle size is ~2 nm. Our results are in agreement with former studies that suggest that the gold atoms involved in the hydrogenation process are those of low coordination.

Oct 1, 2003

By Bertrand Robinson

Great advances have been made in rubber-lined pumps for the pumping of mill pulps. The Canadian Allis Chalmers alone report ov.er 300 such pumps put into service during the past four years. Pumps in which both the casing and the impeller are rubber covered have proved most economical in handling the usual run of mill pulps, effecting large savings in power, maintenance, and shutdown costs. For the handling of pulps containing comparatively large, sharper edged /articles, rubber-lined casings with hard iron impellers have been developed by the pumping departments of Hollinger and Noranda. These rubber-iron combination pumps show an appreciable reduction in overall pumping costs as compared with the all-rubber and the all-iron pumps. The power efficiency is lower in rubber-iron than in all-rubber pumps but higher than in the all-iron pumps, with lower replacement costs due to the cheap iron impellers used. Where continuous operation is essential, however, and duplication of units to take care of shutdown time for replacement of parts is not within the expenditure budget of the company, all-rubber pumps are being used t0 a greater extent. As in all items pertaining to milling operations, the economics of the situation must be studied as closely as the technical details, to arrive at the most advisable practice.

Jan 1, 1939

Arguably the SMC Test® has become the most popular laboratory hardness test in the world with over 17,000 tests having been completed to date, covering over 650 different ore bodies. It is now routinely used in design, optimisation and orebody profiling projects. The test is unique in that from relatively small amounts of drill core it simultaneously provides parameters that are used in simulation modelling of AG/SAG and crushing circuits as well as work indices that are used in power-based equations for predicting the specific energies of AG/SAG/Crushing and HPGR circuits. The very large data base that has been accumulated has provided the opportunity to study the differences in variability from deposit to deposit. This paper describes and discusses the trends that have become apparent from the study of this data base. Recommendations for appropriate selection of sample numbers are also made which are based on these trends.

Jan 1, 2012

By M. T. Shehata, R. W. Revie, M. Elboujdaini

Environmentally assisted cracks in linepipe steels are initiated either as a result of stresses in combination with environmental effects, as in stress corrosion cracking (SCC), or as a result of trapped hydrogen in the steel, as in hydrogen-induced cracking (HIC). To understand better the mechanism of the crack initiation process, key metallurgical and environmental elements that can affect the cracking phenomena were investigated and are reviewed in this paper. The complexity of both cracking phenomena results from the dependence of SCC and HIC on multiple metallurgical, mechanical, and environmental parameters that may all influence both crack initiation and propagation; e.g., composition, microstructure and non-metallic inclusions in the steel, applied stress, water chemistry in the field, and ionic concentrations in the groundwater near the pipe surface to name a few for SCC. In addition, for HIC phenomena, one can add the concentration of H2S in the fluids transported in the pipe as well as concentration of CO2, pH, etc. In this paper, cracking of linepipe steels is analyzed critically, with particular attention to the crack initiation process. The paper is divided into two parts: The first part covers SCC and the second covers HIC.

Jan 1, 2005

By A. Hutwalker, T. Plett

"Blast fumes are one of the major sources for NOx in underground mines. In 2016, the Occupational Exposure Limits for NOx in Germany were reduced by 90%. The task is to keep re-entry times after blasting at the present level and thereby ensure an economic operation of the mine. Measurements show that using ventilation solely is not sufficient. A new approach to reduce NOx from blast fumes is described. Laboratory experiments were performed and a reduction of NOx was observed. Measurements were conducted at an explosive factory’s testing facility and in an underground mine at blasting operations. INTRODUCTION Whether for production of ore or for drift development, the processes in an underground mine are always the same: 1) fracturing the rock, 2) loading the pile, 3) support the resulting cavity. The fracturing of the rock can be done mechanically, by cutting, for example by using continuous miners or tunnel boring machines, or by drilling and blasting. Drilling and blasting is more flexible than mechanical driving, as it can be used independently of the rock strength. Furthermore, this driving method allows a more flexible reaction to changes in geological and/or operational conditions. Thus, underground mining and blasting are almost inextricably linked with each other, and regardless of the size and level of technology of the mine, blasting is hardly avoidable. Depending on the mining method chosen and the existing framework conditions, such as the mechanical properties of the rock or the availability of machinery, blasting is an integral part of daily operations. Even in mines where blasting is not part of regular operations, it cannot be completely avoided. The blast fumes generated by the explosions are, in addition to diesel engine emissions, one of the two main sources of emissions of nitrous gases underground. Up to now, state of the art for dealing with blast fumes is ventilation. The fumes are diluted with fresh air and ventilated out of the mine. This treatment of blast fumes is more than sufficient with the former German Occupational Exposure Limits (OEL). The adaption of the OEL in Germany to the recommendations of the Committee on Occupational Exposure Limits (SCOEL), a committee of the European Commission, leads to big challenges for the mining industry in reducing the concentrations of these gases at the workplaces underground. On its meeting on May 2nd and 3rd 2016, the Committee on Hazardous Substances (Ausschuss für Gefahrstoffe, AGS), an advisory body of the German Federal Ministry of Labour and Social Affairs (BMAS), advised the BMAS to copy the OEL, as recommended by the SCOEL, to the Technical Rules for Hazardous Substances (TRGS 900). BMAS followed this advice, consequently the new OEL where published on November 4th 2016 and became part of the TRGS 900. Table 1 shows the former and new OEL for Germany. These new OEL became law after publishing, but two exceptions were made: For tunneling operations, they became law on October 31st 2017, for mining operations they will become law on October 31st 2021 (BAuA, 2004, 2016, 2017)."

Jan 1, 2019

By S. Bergquist

In this paper, it is investigated how different types of automation would affect the safety for workers in asphalt paving. The risk for the workers on road construction sites is consistently high in comparison to the average risk of the working population. Automation has been suggested as an alternative for improving the safety in roadside construction assuming that removing workers will inherently eliminate the risk of them being injured. In this paper, the potential for improving the safety using automation is analyzed in detail. By investigating accident statistics and understanding the type of accidents that appear, several different automated functions for increased safety are proposed and described. Based on available statistics, it is possible to estimate the safety benefit, as the reduction in fatalities, for several of the proposed functions. The highest safety benefit would be achieved by automating the road traffic driving through the work zones. This has the potential of reducing the total number of road worker fatalities with over 30 %. In addition, it would decrease the number of road traffic accidents in work zones. Automation of construction machinery and dump-trucks also has the potential to increase the safety.

Aug 1, 2013

By K. S. Coley, G. A. Irons, T. Kaneyasu

"It is very important to reveal the lime dissolution mechanism in steelmaking slag, to promote its dissolution without calcium fluoride, which is now almost forbidden for use in most industrialized countries. In this research, the purpose was focused on the development of an experimental method to measure the mutual diffusivity of Ca2+ under the condition of lime dissolution into slag. By forming diffusion couples using a ""vacuum slag aspirating technique"", the method was established. The following mutual diffusivities of Ca2+, in CaO-SiO2-FeO slag systems, imitating oxygen steelmaking slag, were determined using this method:4.1*10-10 m2/s at 1400°C for 27wt.%CaO-53wt.%SiO2-20wt.%FeO slag,4.3* 10-10 m2/s and at 1400°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag, and 1.3*10-10 m2/s at 1250°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag.It was also verified that, if the basicity and ferrite content of the bulk slag are low, then a calcium silicate film forms on the lime surface, and drastically deters the lime dissolution."

Jan 1, 2004

By D. D. Macdonald, G. Engelhardt

The accumulation of damage due to localized corrosion [pitting, stress corrosion cracking (SCC), corrosion fatigue (CF), crevice corrosion (CC), and erosion-corrosion (EC)] in complex industrial systems, such as power plants, refineries, desalination systems, etc., poses a threat to continued safe and economic operation, primarily because of the sudden, catastrophic nature of the resulting failures. Of particular interest in managing these forms of damage is the development of robust algorithms that can be used to predict the integrated damage as a function of time and as a function of the operating conditions of the system. Because complex systems of the same design rapidly become unique, due to differences in operating histories, and because failures are rare events, there is generally insufficient data on any given system to derive reliable empirical models that capture the impact of all (or even some) of the important independent variables. Accordingly, empirical models have generally failed to provide a robust basis for predicting the accumulation of corrosion damage in complex systems under realistic operating conditions. The alternative prediction philosophy is determinism, in which the development of damage is described in terms of valid, physico-electrochemical mechanisms with the output being constrained by the natural laws. The differential damage is then integrated along the corrosion evolutionary path for the system (i.e., over the future operating "history") to yield the desired integrated damage, which is the quantity that is most useful to an operator. In this paper, we review the theory of predicting corrosion damage within the framework of Damage Function Analysis (DFA), with particular emphasis on the pitting of aluminum in chloride solutions and on the accumulation of damage from SCC in Type 304 SS components in the primary coolant circuits of Boiling Water (Nuclear) Reactors (BWRs). These cases have been selected to illustrate the various phases through which localized corrosion damage occurs.

Jan 1, 2005