Search Documents

By Moe Momayez

Shotcrete is a practical and economical support system in many Canadian underground mines. Although shotcrete technology has gained acceptance in the mining industry, there are some problems that have emerged with respect to quality assessment and thickness measurement of the liner. This paper presents recent tests performed with a miniature seismic reflection device developed primarily for thickness measurement of this heterogeneous liner. Work was performed on site in an underground mine in Ontario, Canada. This paper also presents the results from laboratory tests performed on fibre reinforced and non-reinforced shotcrete panels that were used to assess the P-wave velocity in both materials. The results of these tests were used in a second on site investigation. The NDT thickness measurements showed good agreement with direct thickness measurement such as coring.

May 1, 2001

By S Sokhanvaran

Electrodeposition of silicon from a cryolite based electrolyte at a relatively low temperature (1000°C) is a promising approach to generate high purity silicon. In order to obtain fundamental data pertaining to electrowinning of silicon from Cryolite?SiO2 melts, density and electrical conductivity measurements were made. A range of temperatures and SiO2 contents was studied for each property. It was found that while density has an inverse relationship with temperature, the dependence for electrical conductivity is direct. Increasing silica content up to the saturation limit (~ 5 wt%) increases the density whereas further increase in SiO2, lowers the melt density. On the other hand, the conductivity is lower for the melts with greater SiO2 content, at any temperature.

Jan 1, 2011

By Qing-hua Tian, Li-then Cheng, Xue-yi Guo

In order to recycle valuable metals from silver separated residue, a novel method using alkaline smelting at low temperature was proposed. The main factors affecting the main metal recovery such as the smelting temperature, smelting time, liquid-to-solid ratio and alkali addition were investigated comprehensively. The behavior of the main metal elements, such as Pb, Sn, Sb and Bi in silver separated residue was also discussed. The results indicated that amphoteric metals such as Pb and Sn can be smelted into the melt, while other metal elements, such as Sb and Bi were left in the residue.

Jan 1, 2011

By L. Bichler

Lightweight magnesium alloys are gaining in popularity for applications in the automotive and aerospace industries, Their use, however, remains limited due to their relatively low strength and creep properties. Lost Foam Casting (LFC) is a new casting process and the strength of foam cast magnesium alloys has not been investigated in great detail thus far, In this research, magnesium alloy AZ91 E and three new alloys were cast by the LFC process to study the effect of varying aluminum and manganese content on the alloy's tensile properties, The study reveals, that the tensile strength of the magnesium alloy is closely related to the relative amount of aluminum in the system. Formation of ß-Mg17Al12 phase was seen to significantly affect the yield strength and ductility of the alloy, Furthermore, formation of manganese intermetallic compounds was seen to effectively increase yield strength of the base alloy, Individual alloy morphologies were analyzed via optical and SEM techniques.

Jan 1, 2004

By Peter Moon

THE mineral industry of Canada relies heavily upon the talent of its technical men. It is vital to the well-being of the industry that its supply of young, trained men be adequate. At the present time, the industry is acquiring only 200 new graduates a year. The shrinking supply is far below present and future requirements. Other industries and research organizations are competing for engineers and scientists. Dr. J. B. Mawdsley (1), Past-President of the Canadian Institute of Mining and Metallurgy, has recently outlined a program designed to attack the problem. Dr. J'. C. Sproule (2), another former President of the Institute, has stated that: "The need for selection of trainee material is commonly recognized, but little is done about it." The following paper contains a short discussion of occupational interests, and outlines research, using psychological knowledge and measuring techniques, aimed at the identification of desirable recruits for the mineral industry.

Jan 1, 1963

By Subagyo, Geoffrey Brooks, Ken Coley

The generation of droplets and their subsequent reaction in the emulsion is critical to the overall kinetics of oxygen steelmaking. High temperature experiments have been performed at McMaster University to study this behavior. The results from this work and other previous studies has formed the basis of a number of physical and chemical models that attempt to describe the critical aspects of droplet behavior in Oxygen Steelmaking. These models include semi-empirical models for predicting droplet generation rate, droplet size distribution and droplet residence time as a function of blowing parameters.

Jan 1, 2004

By R. Heikkilä

A large research and development program called RYM PRE (Process Re-Engineering) has been active in Finland since 2010. As a part of the program, a work packet Infra FINBIM is focused on the development of new national process model, specifications and requirements for the whole Finnish Infra Industry. In the Infra FINBIM, total 15 companies and main owners and 3 research organisations are included. The work is further continuing. The main achieved results up today have been the first specifications and requirements of the BIM based total process for infra sector, about 30 different pilot projects for testing of the new design and construction process models producing a lot of results and observations, a new open information transfer format Inframodel3 based on LandXML standard, the achieved acceptance of the Building SMART organization for support of international development, utilization and extension of the format within the whole infra industry, processes, software and other technical equipment. An evaluation of the results and this work will be drawn.

Aug 1, 2013

By Amir Asadi

Various damage modes that evolve with time in polymer composite laminates, such as transverse cracking, vertical cracking, delamination, and fiber fracture, as well as the interaction among them, influence the time-dependent degradation in modulus (creep) and strength (creep rupture) of polymer composite laminates. This study is focused on modeling the time-dependent evolution of transverse cracking in [90] plies of a multidirectional polymer composite laminate [0m/190n]. This model uses a two-dimensional variational analysis to determine the stress state at any given creep time. The elastic stored energy, determined using this stress state, is compared with a critical energy for fracture to determine the crack evolution with creep time. Model predictions are compared with experimental results to validate the model.

Jan 1, 2010

By Zhan Zhang, Hiromi Nagaumi, Zhen Li

"Recently, the remarkable strengthening effect of ??-Al(Mn, Fe) Si dispersoids at both ambient temperature and elevated temperature were found by several researches. A large amount of dispersoids can be formed by applying special heat treatments and within a suitable range of chemical composition of AA3xxx alloys. In the present work, the influences of Cr addition on the mechanical properties and microstructures of the Al-Mn-Mg-Si alloys were investigated. The mechanical properties at ambient and elevated temperatures were evaluated by micro-hardness and yield strength. Moreover, the microstructures in as-cast and heat-treated conditions were quantitatively analyzed by optical and electron microscopes. Results revealed that Cr also had effect on the number density and volume fraction of dispersoids. Micro-hardness and yield strength at ambient temperature increased with the increasing content of Cr, and the Cr addition increased the yield strength at elevated temperature as well. Moreover, the creep resistance at 300°C improved dramatically with the increasing content of Cr.INTRODUCTION Traditionally, AA3xxx aluminum alloys were widely used in packaging, automobile and architecture industries, because of its good formability, excellent corrosion resistance and weldability. And AA3xxx alloys were considered as non-heat-treatable alloys. However, the strengthening effect of dispersoids in AA3xxx alloys was discovered recently (Li & Arnberg, 2003;Li, Muggerud, Olsen, & Furu, 2012; Li, Zhang, & Chen, 2016; Liu & Chen, 2015).Alarge amount of dispersoids could precipitate by a proper heat treatment.In order to further improve AA3xxxalloys, the composition of the alloys should be optimized. A few previous studies were reported to investigate the influence of compositions on AA3xxx alloys. Adding Mn element could enhance the precipitation of ??-Al(Mn, Fe)Si dispersoids and improve the yield strength(Muggerud, Mørtsell, Li, & Holmestad, 2013), as long as the concentration of Mn was under the solid solution limit. Fe decreased the solubility of Mn and accelerated the precipitation rate of ??-Al(Mn, Fe)Sidispersoids(Li & Arnberg, 2003), the yield strength and creep resistance at elevated temperature could increase with an optimized content of Fe(Liu & Chen, 2016). Mg element would affect the nucleation process of ??-Al(Mn, Fe)Sidispersoids by forming metastable Mg2Si(Hirasawa, 1975; Li, Zhang, & Chen, 2017a; Lodgaard & Ryum, 2000), metastable Mg2Si precipitated during heating process and promoted the precipitation of ??-Al(Mn, Fe)Sidispersoids, moreover, Mg provided solid solution strength for AA3004 alloys(Li et al., 2016). Si increased the volume fractionof ??-Al(Mn, Fe)Sidispersoids(Muggerud et al., 2013)and decreased the size of ??-Al(Mn, Fe)Sidispersoids(Li, Zhang, & Chen, 2017b). With the addition of Mo, the size of dispersoids became finer with a higher volume fraction, the volume percentage of dispersoid free zones was reduced. Elevated temperature yield strength and creep resistance improved due to Mo addition (Liu, Ma, & Chen, 2017).However, the effect of Crelements on microstructure and mechanical properties of AA3xxx alloys were rarely reported."

Jan 1, 2018

By H. Chaouki

The aim of this work is to simulate the forming process of a green anode. For this purpose, a nonlinear compressible viscoelastic constitutive law is presented. The concept of natural reference configuration is considered. Within an isothermal thermodynamic framework, a Helmholtz free energy is proposed to take into account the nonlinear compressible deformation process occurring between natural reference configuration and current configuration. A dissipation potential is introduced in order to characterize the irreversible aspect of compaction process. Thus, the constitutive law is formulated through two equations: 1) an expression of Cauchy stress tensor and 2) a differential equation characterizing the evolution of the natural reference configuration. Material parameters are assumed to be a function of the bulk density. This allows capturing the micro-mechanical phenomena within the chosen macroscopic approach. An experimental study based on compaction tests is carried out in order to characterize the mechanical behaviour of the anode paste. A user's material VUMAT subroutine for finite element dynamic explicit analysis has been developed and implemented in the ABAQUS commercial software. To evaluate the model predictive capability, numerical simulations of the compaction forming process of anode paste were performed. Simulation results show that the constitutive law predicts the experimental trends and gives interesting physical responses. This constitutes a first step toward making a benchmark with experimental results on the forming process of anode paste.

Jan 1, 2011

By Gurinder Kaur

Selenium (Se) based materials find wide applications in rectifiers, solar cells, photographic exposure meters, data storage devices, xerography and anticancer agents. They are also used in the glass industry to eliminate bubbles and remove undesirable tints produced by iron. In addition, Se is highly reactive towards a wealth of chemicals that can be potentially exploited to convert Se into other functional materials such as CdSe, ZnSe, Ag2Se. Here, we report a review of structural investigations of Se based materials in glassy and nanostructured forms. Glasses having varying amounts of Se and Tellurium (Te) were doped with group IV and V elements such as antimony and tin. Structural changes accompanying the composition variation were characterized with x-ray photoelectron spectroscopy, differential scanning calorimetry and x-ray absorption near edge spectroscopy. At the same time Se-Te nanoalloys were synthesized in aqueous micellar phase using Na2SeO3/Na2TeO3 as the Se/Te source. Morphology change from nanoparticles to nanoribbons was investigated using Scanning and Transmission Electron Microscopy (SEM/TEM) techniques. Structural investigations were also done for well defined morphologies of Se based nano-biomaterials obtained in the presence of water soluble protein bovine serum albumin (BSA).

Aug 1, 2013

By Northeastern University, B. Y. Cui, B. Y. Wang, D. Z. Wei, W. G. Liu, Z. C. Guan, S. L. Gao

To recover iron values from low grade ores by reverse froth flotation method, further research on cationic collectors used in reverse flotation of iron ores is launched to promote the utilization efficiency of iron ores. In this paper, one new cationic surfactant, bis(2-hydroxylethyl) dodecylamine (BHD), that could be dissolved in water easily was used as collector for quartz flotation. Flotation results indicated that BHD shows stronger collecting performance on quartz than hematite. The maximum recovery of 96.30% to quartz is obtained at a collector concentration of 20.0 mg/L in the pulp pH range from 5 to 7. This collector can be used to float quartz from hematite. And optimal separation results with 86.59% iron recovery and 66.60% iron grade to synthetic sample were achieved at a collector concentration of 20.0 mg/L and pulp pH of 5.02 when hematite and quartz were mixed at a mass ratio of 3:2. The adsorption mechanism of the collector on quartz surface was investigated by XPS analysis, infrared spectroscopic analysis and zeta-potential measurements, which revealed that electrostatic attraction and hydrogen bonding adsorption occur between collector and quartz surface.

Jan 1, 2016

By A. H. Onur

Spontaneous combustion of coal is a significant hazard in underground coal mines. It causes serious problems for miners for many years after the fact. It threatens workers? lives and causes economic losses for companies. It disrupts coal production and makes it necessary to abandon the main drift where the spontaneous combustion occurred. Coal fires have to be prevented before they occur; otherwise they are very hard to control. Precautions thus have to be taken in potentially risky areas. For coal to spontaneously combust, it needs 3 elements: fuel, oxygen and heat. If one of them is missing, the fire cannot occur. The best way to prevent spontaneous combustion is to prevent contact between coal and air. Coating of the coal surface with an air-proof lining material would be a practical and useful solution to prevent spontaneous combustion of coal. In the scope of this study, a lining material for coating the coal surface was designed at laboratory conditions. Lining material to be used for preventing coal fires should be airproof, cheap, sufficiently strong, have low rebound, be water- and heat-resistant, and easily obtained and applied. It should also be safe for human health when in contact with mine ventilation. By considering these obligations, 3 kinds of gypsum (plaster, satin plaster, molding plaster), as well as lime, cement and fly ash and different mixtures of these materials were applied in laboratory conditions to form a lining material. Samples of lining material were subjected to uniaxial compressive strength tests to determine their behavior against roof loads. Although there is no need to carry any roof load, the lining material has to be sufficiently strong to stay in place on the applied surface. If the lining material is broken, coal and oxygen can react again. Air permeability and curing time of the mixtures were also tested in laboratory conditions. Then the tested mixtures were applied on a wall with a pump to test the applicability of mixtures. After all tests were performed in laboratory, the most suitable mixture was determined as the optimal lining material to prevent coal fires.

Aug 1, 2013

By A. Warczok

Metal losses in discard slag are the main factor determining overall recovery. The metals are present both in dissolved form and as matte or metallic inclusions, varying in size from 2 to 1000 µm. Pyrometallurgical slag cleaning usually consists of heating the slag, reduction of oxides and settling of matte/metal droplets. Heating the slag decreases viscosity and accelerates reactions. Reduction of magnetite liberates inclusions and facilitates co-reduction of dissolved metal oxides. A significant amount of the matte and metal is present as very fine metallic inclusions, too small for settling. The coalescence of these matte or metal inclusions is required to remove them from the slag. The developed new concept of slag cleaning combines DC furnace technology with an extra magnetic field for vigorous slag stirring, enhancing mass transfer to the reductant surface, accelerating the rate of reduction, and destabilizing the emulsion of matte or metal inclusions. Intensive slag stirring increases the probability of collision of inclusions, will accelerate their growth and will therefore improve settling. The process is carried out in a patented DC channel furnace, where the liquid metal or matte layer acts as a cathode and the floating coke bed on the slag surface is the anode. In the first part of the furnace, a superimposed magnetic field induces a Lorentz's force causing the slag to start an intensive circular motion. The next furnace zone does not experience any stirring and is dedicated for quiet sedimentation of the inclusions. A mathematical model of gravitational coalescence combined with forced slag motion showed the possibilities of effective removal of copper matte inclusions. The results of laboratory pilot scale tests of continuous slag cleaning showed fast slag reduction and confirmed the improved matte removal from the slag. Conceptual analysis shows the potential use of the technology in various other non-ferrous industries, like for example nickel plants. It is also possible to use this technique batch wise.

Jan 1, 2007

By D. K. Sarkar, J. Perron, J. D. Brassard

"Nearly perfect spherical shaped water drops rolling-off from the surface of lotus leaf is one of the beauties of nature. This kind of surface is called superhydrophobic, since the water does not like it. Physically, a superhydrophobic surface provides a contact angle (CA) of water over 150°. The combinations of both mico-nanostructure topography as well as low surface energy are essential to have such high CA on a surface. Nano-micro structured superhydrophobic surfaces have been developed in different methods. (i) Monodispersed fluorinated silica nanoparticles have been synthetized via Stöber Sol-Gel process and deposited on various surfaces, such as aluminium or glass, to obtain transparent superhydrophobic thin films. (ii) Similarly, zinc stearate nanocomposite coating has been fabricated by spray process on the same substrates. These thin films are found mechanically robust with drag reduction of coefficient 16% lower than as-received surfaces. (iii) By electrodepositing pure zinc on steel surfaces and further coating it with diluted room-temperature vulcanized silicone rubber, the surface become superhydrophobic. This superhydrophobic surface protects the steel against corrosion by increasing the polarization resistance from 1.5 k? on steel to 44.4 k?. This coating also reduced the ice adhesion on the steel surface 6.3 times as compared to bare steel substrates. Globally, these superhydrophobic surfaces have tremendous applications against corrosion reductions, drag reductions and ice adhesion reductions.INTRODUCTIONSuperhydrophobic coatings are increasingly attractive to the industry and academia due to their unique self-cleaning properties as a result of their water repelling characteristics. Fabrication of superhydrophobic coating is an inspiration from nature as water is seen to repel on many natural surfaces such as those of the lotus leaves, butterfly wings, water striders’ legs, and so on (Gao & Jiang, 2004; J. Huang, Wang & Wang, 2006; Neinhuis & Barthlott, 1997; Zheng, Gao & Jiang, 2007). This non-wetting phenomenon is well understood on lotus leaves, shown on the Figure 1 (a), and it is considered as the basis of the studies of superhydrophobicity. The existence of this binary structure on the surface of the lotus leaves allows a large amount of air entrapment and consequently reduces the contact area of water on it and the presence of low surface energy waxy components with reduced affinity to water together leads to the superhydrophobic properties. The phenomenon is shown on Figure 1 (b). Cassie and Baxter (Cassie & Baxter, 1944) as well as Wenzel (Wenzel, 1936) proposed two mathematical models to explain the wetting phenomena on rough surfaces that leads to superhydrophobic properties. By definition, superhydrophobic surfaces are characterized by a water contact angle value = 150° with the rolling off of water drops from the surfaces (Sarkar & Saleema, 2010). Superhydrophobic surfaces find tremendous importance in the technological world where it can applied in domains such as anti-corrosion, anti-biofouling, electrowetting, icephobic and even in drag reductions (Bushnell & Moore, 1991; Cao, Jones, Sikka, Wu & Gao, 2009; Carlborg & van der Wijngaart, 2010; Carré & Mittal, 2009; Y. Huang, Sarkar & Chen, 2010a; R. Karmouch, Coude, Abel & Ross, 2009). However, the most important challenge faced by industries is their feasibility large scale in an effective an economical manner."

Jan 1, 2016

By Bertrand Quiniou, Pierre Amadieu

Ion exchange technologies and processes are proven and established technologies widely used in numerous industries including hydrometallurgy for metal separation and recovery from metal bearing solutions. They have evolved through innovation which includes the development of countercurrent multistage (or multivessel) ion-exchange contactor systems with the benefit, for industrial operations, of greatly reduced footprints and ion-exchange media inventories, as compared to more traditional fixed bed contactor systems. Information on procedures for design and sizing of countercurrent multistage ion-exchange contactor systems is not readily available since it is most often proprietary know-how. The purpose of the present work is to develop a simple and innovative approach for the sizing and modeling of industrial countercurrent multistage ion-exchange contactor systems. The suggested approach builds upon published results and upon the following observation: in an industrial setting, knowledge of how component concentration or load on a contactor output streams vary with time t within a cycle duration (0 < t < T) is generally of little interest, only knowledge of time average of such concentration or load over a cycle duration T is sought for. The presented approach will be tested against current or past performances of industrial countercurrent multistage contactors of Orano Mining operations such as SNK‑3M moving packed bed contactors in Kazakhstan and NIMCIX fluidized bed contactors in Namibia.

Jan 1, 2020

By E. J. Schwarz, A. A. Winir

"Absolute magnetite contents were determined for asbestos specimens in various stages of milling by using a Faraday-type thermomagnetic balance. Comparison of these results with magnetic ratings (MR) supplied by the mining companies cooperating in this study reveals strong scatter. The main cause of this scatter is thought to be that the MR values were obtained in magnetic fields well below the saturating field of magnetite (5,000 oe). However, only the saturation moment is an intrinsic property and consequently must be used for the purpose of obtaining reliable estimates of the magnetite content. Curie points indicate that virtually pure magnetite and possibly Ni3Fe is present in all samples, and another phase, probably (Cr, Al) magnetite, is present in a few samples. The susceptibility in fields stronger than 5,000 oe is positive and falls in the normal paramagnetic range, whereas sy nthetic chrysotile exhibits weak diamagnetism. This suggests that, as a general rule, the least adulterated natural chrysotile concurs with the samples showing the smallest positive susceptibility above 5,000 oe. The magnetite appears to increase in quantity with a decrease in fibre length and to be somewhat more uniform in distribution for samples showing substantial fiberization (opening of the fibres)."

Jan 1, 1971

By Mohammad Reza Khalesi, Ruhollah Rezazadeh, Mohsen Izadi Yazdan Abadi, Mahmoud Abdollahy

"The rotary vacuum drum filter (RVDF) is widely used for dewatering in mining industrial. In general, different parameters have influence in the solid-liquid separation such as: solid percent, level of vacuum, particle size distribution, filter cloth and chemical additives. These parameters can influence on some variables such as cake moisture, throughput and filter cloth life time. The aim of this study is to propose some chemical additives to improve the rate of filtration and decrease cake moisture of Gol-E Gohar iron ore concentrate by using laboratory scale bottom feed vacuum filter and suggest a filter cloth with long life time (more than 400 hours). Effect of particle size distribution on filtration investigated in large scale by measuring the thickness of cake and cake moisture.Increasing molecular weight of anionic flocculant lead to increases throughput but cake moisture increases too; While the filter aid increases throughput and decreases cake moisture simultaneously; the combination of them show different behavior. TSS and filter cloth life time have directly relation with material and type of filter cloth weave. Depending to type of feed, two polyester and polypropylene filter cloth are suggested. More over twill and satin weave have the best results. To prove the laboratory results some industrial tests performed in Gol-E Gohar hematite iron ore concentrate plant.INTRODUCTION“The process of grinding and classification involves the use of large quantities of water. The separation of solids from liquids is usually achieved by gravity sedimentation in thickeners. For fine particles this is a slow process. In general, 75–80% of the water can be separated and removed by thickeners. For further water removal, filters are used where in excess of 90% of the water can be removed” (Gupta, 2006).“Many types of filters are available, which are broadly classified here as vacuum, pressure, precoat and depth filters. Each classification contains a number of sub-processes. A category of filter that uses vacuum induced driving forces and semipermeable media to facilitate the separation of solids from suspension. While pressure differences across the filter are limited to less than 85 KPa (usually 75 KPa), most units are capable of processing a wide range of feed materials in a continuous manner” (Rushton, 2008)."

Jan 1, 2016

By X. -G. Chen, K. Liu, N. Parson

"Precipitation-strengthening 6xxx alloys are widely used for building and construction and automobile industries due to their high strength, good weldability and corrosion resistance. However, their elevated-temperature properties (250–300°C) decrease rapidly due to the fast-coarsening of precipitates. On the other hand, dispersoid-hardening is one of the most efficient approaches to improve the elevated-temperature properties. Therefore, the evolution of dispersoids during heat treatment in Al-Mg-Si-Mn alloys was investigated in the present work. Various heat treatments with temperatures ranging from 300–500°Cfor up to 24 hours were performed. Electrical conductivity and microhardness were measured while optical and scanning electron microscopy combined with image analysis, were used to characterize the dispersoids. Special emphasis was placed on the evolution of the size and number density of the dispersoids under different heat treatment parameters. It was found that dispersoids started to precipitate at 350°Cfor 1 hour. Nucleation and growth were the main mechanisms at temperatures up to 400°Cwhile coarsening occurred at temperatures above 450°C. The quantitative results indicated that dispersoids precipitation reached the optimum condition after treatment at 400°Cfor 2–4 hours with a fine size and high number density, resulting in the highest hardness.INTRODUCTIONThe precipitation-hardening 6xxx aluminum alloys with major alloying elements of Mg and Si are one of the most widely used aluminum alloys for building and construction and automobile industries (Dinaharan & Murugan, 2012). In recent years, there have been increasing demands for aluminum structural components to be used at elevated temperatures (250–300°C) for different applications. However, the mechanical properties of 6xxx alloys at elevated temperature are typically reduced due to the rapid coarsening of precipitates at 250–300°C. It has been reported that the yield strength (YS) of AA6061 in the peak-aged condition drops from 276 MPa at room temperature to only 30 MPa at 315°C(Kaufman, 1999). Therefore, it is a key concern to improve the elevated-temperature properties of 6xxx alloys to expand their range of applications."

Jan 1, 2018

By C. K. Wilton

"The Agnew Lake uranium deposits were discovered in 1953 following the discovery of the Elliot Lake deposits to the west. The original property was optioned to Kerr Addison Mines Limited who added additional claims by staking. Agnew Lake Mines Limited was incorporated in 1967 to develop the property and a shaft was sunk to 1040 metres and five levels developed before work was suspended due to low uranium prices at the end of1970.In 1974-75 the mine was dewatered and production started in 1977. By 1978 reserves were estimated at 10,000,000 tonnes averaging 0.35 kg. U10 , per tonne. Underground operations were terminated in 1980 although a uranium leaching operation was continued until early 1983.The deposits lie near the contact of Huronian metasediments with underlying Algoman granite. The sediments consist of arkose, conglomerate, argillite and quartzite with the uranium mineralogy mainly confined to oligomictic quartz pebble conglomerate. The higher uranium values are related to conglomerate with highest percentage of pebbles. The chief uranium minerals are uranothorite and monazite. It is of interest that the uranium thorium ratio differs appreciably from that of the Elliot Lake deposits. This fact along with the fact that the Elliot Lake sediments were deposited by paleocurrents from the northwest whereas the Agnew Lake sediments were deposited by paleocurrents from the northeast indicates widely separate sources for the deposits. It is suggested that the Agnew Lake uranium deposits are syngenetic placers deposited under anoxygenic atmospheric conditions."

Jan 1, 1986