Search Documents

By L Munholand, G. Soucy, P. Quintal

This work presents early results from the first study to optimize the hydrodynamics of a Plasma Lift Reactor (PLR). The PLR is designed to break down organic contaminants in aqueous solutions. New experimental results are presented for air/water tests and for plasma degradation of organic contaminants in Bayer liquor. In addition, a multiphase Computational Fluid Dynamics (CFD) model has been developed which predicts the hydrodynamic behavior in the PLR. These results of this work suggest the PLR is effective at reducing contaminants in the Bayer liquor and that the CFD model adequately describes the hydrodynamic flow.

Jan 1, 2005

By Doug Milne

Linking Classification Systems with each other Similar Parameters between systems Different Rock Mass Properties Rock Mass Classification parameters and geology Different sources of data Commonly Used Rock Mass Classification Systems Q? = Q with SRF = 1.0 RMR? = RMR with no joint orientation correction RMR76 = 9lnQ + 44 RMR?76 = 9lnQ? + 44 RMR76 = RMR89-5 RMR?76 = GSI = RMR89-5 MRMR = ??MRMR

May 1, 2013

By S. Qian

Galvanic corrosion is a potentially major concern associated with the application of stainless steel reinforcement which is in direct (electrical) contact with carbon steel reinforcement in concrete structures. Judicious use of stainless steel rebar in both new construction and rehabilitation of older structures is a viable, cost-effective option for extending service life and reducing maintenance costs. Questions, however, had arisen about the possibility of increased corrosion due to galvanic effects. This paper investigates the galvanic-coupling behaviours of three different types of stainless steel and carbon steel. Tests were performed both in electrochemical cells and with specimens in concrete inside an environmental chamber. The results show that oxygen reduction on stainless steel is the rate-determining factor for galvanic coupling of these two metals. It is much lower than that of passive carbon steel. As a result, the galvanic coupling of stainless steel with carbon steel will not increase the risk of corrosion of carbon steel reinforcement.

Jan 1, 2005

By M. Elmadagli

Wear mechanisms of two commercial aluminum alloys, namely a spray formed and extruded Al-25%Si alloy, and a sand cast A390 alloy (18.5 %Si) that are known to be successful in cylinder bore technology were studied to have a better understanding of the requirements for wear resistant aluminum alloy design. From durability point of view these alloys are known to be successful for engine bore applications. It is interesting to compare the wear mechanisms in these alloys because they have significantly different silicon content and microstructures, and were produced using different techniques. The wear tests were done using a block-on-ring configuration, in controlled air atmospheres (5 % relative humidity). In spite of the differences in silicon content and microstructure, the wear mechanisms were similar and consisted of formation and destruction of hard tribolayers that are either formed by either mechanical or chemical interactions on contact surfaces. The differences in the wear rates between the two alloys arose from the differences in the hardness of the worn surfaces, and the alloy's ability to sustain the tribolayers on the worn surfaces.

Jan 1, 2004

By Davis. B. R.

There are a number of hydrogen storage systems proposed for automotive applications. However, all of the current suggestions fall short of the DOE targets for storage density and volumetric density. The DOE has suggested that only through radically new ideas will a practical solution to hydrogen storage for automotive applications be realized. This paper provides some background in chemical hydrogen storage and discusses roadblocks to the implementation of some proposed technologies.

Jan 1, 2005

By R. Heikkilä

Today road construction sites utilize more and more information modeling in design phases as well as model based 3-D machine control systems in site operations. For main contractor, the management and control of all the site operations is a demanding task including also many challenges created by continuously developing new technology. In the paper, the main requirements for successful dynamic site management are introduced. The dynamic management means real-time possibilities for information acquiring, transfer and further utilization of the information in the management. An integration model to expand the current way of management and the utilization of present 3-D machine control systems is introduced. Different practical test results using two new different dynamic management systems are presented and evaluated. The first experiments and the results have been provided using the prototype system developed in a research project called DigiINFRA by the University of Oulu and Technical Research Center of Finland. Also, there have been tested a new commercial management system developed recently in Finland. In the conclusion, an expectation for the next generation for more dynamic road construction management methods is concluded.

Aug 1, 2013

By Tai Sik Lee

Why ISRU into Space Exploration are important NASA and International Mission statements calls for the sustainable human exploration of the Moon, Near-Earth asteroids, and Mars Common Exploration Goals and Objectives are Strongly influenced by ISRU Extend Human Presence: Continually increase the duration and level of self sufficiency at all destinations Develop Exploration Technologies and Capabilities: Develop and validate tools, technologies, and systems that extract, process, and utilize resource to enable exploration missions Perform Science to Support Human Exploration: Characterize available resources at destinations Stimulate Economic Expansion: Encourage commercial services and create new markets, including markets for discovered resources Enhance Earth Safety: Test techniques to mitigate the risk of asteroid collisions with Earth

May 1, 2013

The AG/SAG circuit discharge P80 is now increasingly referred to as the ?Transfer Size? or T80 for short. From the literature it is apparent that in circuit design some approaches to the sizing of AG/SAG mills as well as the ball mills that they feed use this parameter. This paper reviews whether the use of the T80 is appropriate in this context. In the course of the review examples of AG/SAG discharge size distributions measured from range of operating circuits are used to illustrate the arguments made.

Jan 1, 2012

By R. C. Gilmore

Underground longwall coal mining sections may develop explosive mixtures of methane-air in the mined-out gobs. If the panel are operated as bleederless or sealed gobs, progressive sealing along the gate roads as the longwall face retreats limits the flow of fresh air into the gob and thus deprives potentially explosive atmospheres of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics (CFD) modelling to simulate the flow of gases in longwall gobs. Modelling indicates that targeted injection of nitrogen through the seals along the gate roads inbye the face can be used to control the size and location of methane and air clouds within the gob and to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures in longwall gobs.

Aug 1, 2013

By G. I. Mathieu

"An experimental study was carried out to evaluate the performance of column flotation versus conventional flotation for the recovery of molybdenite from a Newfoundland ore. The objective was to verify the claims made by the inventors of the flotation column, Messrs. Pierre Boutin and Remi Tremblay, that their apparatus reduces the entrainment of fine gangue and other mineral impurities in the froth product. The research included a factorially designed series of tests to determine satisfactory operating conditions of the column. These provided a basis for comparative flotation tests with column and Denver cells. In the course of the work, the action of a few depressants was studied. Results indicated greater selectivity in the column and reduced reagent consumption."

Jan 1, 1972

Between 1993 and 2003, a series of AG and SAG mill pilot plant trials were conducted using Hardinge Ical pilot plant scale SAG mills on numerous ore samples and ranging across a wide variety of operating conditions. The data from these tests were used to evaluate the design of SAG and AG mill circuits for over a dozen projects, of which about half were eventually constructed and commissioned. The data were also used in the development of SAG mill modelling, scale-up and simulation procedures by several consultants who had access to part of the data set. Recently, we have had the opportunity to bring this data together and further analyse the consolidated dataset. This paper reports on the outcomes of this analysis that has identified the impacts of different AG/SAG circuit flowsheets and operating conditions on energy efficiency and operating cost.

Jan 1, 2012

By F. Ajersch, A. R. Hekmat

Apparent viscosities of hypo-eutectic (Al-7% Al) and hyper-eutectic (Al-35% Si) binary alloys were measured in the semi-solid state using a Couette type viscometer at variable shear rates. Analysis of the microstructural evolution demonstrates the differences in the rate and degree of attrition of the primary phase particles which are characteristic of the thixotropic nature of the semi-solid alloy. It was observed that the Si primary phase in the hyper-eutectic alloy is much more difficult to fragment than the dendritic a-Al phase in the hypo-eutectic alloy. For the case of the a-Al, the dendritic structure is broken down by attrition and fracture of the dendrite arms whereas the fracture of the Si hexagonal crystals in the hypereutectic alloy occurs along the {100} and {110} cleavage planes. Results are presented for fixed solid fractions of the primary phase at isotherm condition for each type of alloy.

Jan 1, 2006

By M. B. Greyver

The results of laboratory tests on iron precipitation from non-decopperized nickel anolyte are discussed. The parameters (pH, oxygen consumption and stirring speed) for iron precipitation from the anolyte, using the oxygen in the air, were determined. In the experiments conducted under optimized conditions, the residual concentration of iron in the anolyte after precipitation was 0.7-2.7 mg/L, and the copper and nickel losses to the solid phase were 0.05-0.07% and 0.05-0.16%, respectively. The filtration ability of the iron slurry obtained was 2 to 5 times higher as compared to that after chlorine oxidation and oxyhydrolysis. The leaching of the non-ferrous metals from the iron cake made using the separate nickel anolyte purification process was possible by dissolution in sulphuric acid. It was established that after cobalt precipitation from the copper- and iron-depleted anolyte, the precipitates obtained had lower ratios of Fe:Co and Ni:Co.

Jan 1, 2006

By David Sanscartier, Elizaveta Petelina, Alexey Klyashtorin

This paper provides an overview of the radiological risk mitigation approach applied by the Saskatchewan Research Council (SRC) for the remediation of 35 legacy uranium mine sites in northern Saskatchewan where uranium exploration and extraction took place in the 1950–60s. Mining activities resulted in an irregular increase of the gamma radiation dose rate (up to 18 μSv/h). The radiological objectives for the sites include a gamma dose rate at a spot (<2.5 μSv/h above local background), and the dose rate averaged over a hectare (<1 μSv/h above local background). These objectives are generally achievable at the impacted sites through the installation of shielding soil cover. This method may be impractical for site areas with rough terrain (e.g., steep slopes) and/or difficult access. A risk assessment approach is applied to determine if these areas can be safely left uncovered or if additional mitigation measures should be implemented. The risk assessment approach is based on two factors: (i) the ambient radiation dose rates collected through gamma surveys, and (ii) actual land use data collected through various surveys of activities of local community members at the sites. Exposure scenarios based on four land uses are applied to estimate a potential annual dose load for members of the public. The estimated doses are compared with the criterion of 0.3 mSv/a recommended by the Canadian Guidelines for the Management of Naturally Occurring Radioactive Materials (NORM). If the criteria are not satisfied, a mitigation plan is developed, and post-remediation gamma levels are modelled using GIS tools to evaluate the performance of the proposed mitigations. The proposed approach allows the team to optimize resources for the site remediation so that public exposure to NORM are as low as reasonably achievable after remediation.

Jan 1, 2020

By Baisheng Nie, Longlong Yang, Tao Yang, Wenjie Jia

"Gas adsorption in coal is an exothermic and physical process. Temperature might change during the dynamical process. In order to get the temperature variation of gas adsorption process, the experiment system which can test the temperature variation and analyze the thermal effect was established. Gas adsorption experiments under different conditions were done by using the test system. The results show that temperature increases during the adsorption process. It is an exothermic reaction process. Also, the temperature variation and the variation gradient increase with the increasing of equilibrium pressure. The temperature variation value is smaller if the experiment temperature is higher. The paper will provide basic experimental data for explaining gas adsorption mechanism better.INTRODUCTIONChina is the largest coal producer in the world while it also has the most serious coal mine disasters. According to the statistics, there are nearly a thousand coal mines in China including more than 110 the key state-owned mines risking to happen coal and gas outburst. Hundreds of coal and gas outburst occur each year which often causes serious casualties and economic losses (State Administration of Work Safety, 2007). With the continuing exploitation of the coal resources, the depth of the Chinese coal mines increases about 100 meters every year which causes the situation of gas accident becoming more and more serious (Xie et al., 2006).At present, the real mechanism of gas adsorption, desorption and the diffusion process in coal and the influence factor of it are not so clear. And because of the limit of prediction method and the technological level caused gas accident prevention theory and technology not so valid."

Jan 1, 2015

By Fr. -W. Bach

In the past years the enormous weight saving potential of magnesium sheet has been demonstrated by various research projects all over the world. It has been shown magnesium flat products can benefit automotive, aviation, machine tool and consumer electronics industries. Major material problems such as poor formability, corrosion resistance and high production cost still inhibit the application of magnesium sheets in large scale production. The present contribution outlines achievements in casting and rolling technology. The authors developed an adapted strip casting process in which near-net-shape rolling feedstock of several wrought alloys has been produced. During the rolling process, various parameters were varied in order to modify the microstructure and surface quality of sheet. Several temperature cycles, strains, lubricants, roll surface structures and roll coatings have been analyzed. The sheets were examined and tested in deep-drawing experiments. Suitable rolling schedules have been developed for standard and modified wrought alloys. The study concludes with an overview of current industrial solutions and an estimation of the potential cost savings that might result from the adaptation of the process that has been developed.

Jan 1, 2006

By Y. Nara, N. Aramaki, M. Maruyama

Evaluation of three dimensionally non-uniform strain distribution in rocks under various conditions such as in water or under freeze-thaw cycles is of significant importance to understand their complex deformations and fracturing mechanisms. For this purpose, we developed an image analysis method which can evaluate or “measure” the three dimensional (3-D) strain distribution in rocks. The proposed method utilizes the 3-D images of rock under initial and deformed configurations, which are obtained by some imaging techniques such as X-ray computed tomography (X-rayCT). In the proposed method, the obtained 3-D images are divided into multiple sub-regions of interest. For each sub-region, the strain is evaluated utilizing 3-D affine transform with unknown coefficients to be determined. In the first step, 3-D voxel level displacements at multiple representative points in each sub-region are computed by 3- D digital volume correlation technique between the comparison images and the initial-guess of the transform coefficients are obtained. In the second step, referring to the initial-guess of unknown transform coefficient, they were optimized in sub-voxel level by finding optimum digital volume correlation between the comparison images, which can evaluate the transform coefficients with higher precision. From the calculated transform coefficients, the strain was directly obtained through the spatial derivative of displacement based on affine transform. In this paper, along with the description of the proposed method, the evaluation of deformation in a lignite specimen due to immersion in water was presented as an application example. As the 3-D imaging technique, micro-focus X-rayCT was applied. The result showed that the induced dilatational strain field due to the initiation and extension of cracks in the specimen was clearly captured. Therefore, authors believe that the proposed method can be applicable to various problems in rock mechanics.

Jan 1, 2015

By Qian Liu

Mining in highly stressed ground conditions has been an increasing challenge at the Brunswick Mine. Two large regional pillars were established on the 1000 m Level to support the ground for safe extraction of the surrounding ore. The South Regional Pillar contains about 5 million tonnes of ore and the North Regional Pillar has about 3 million tonnes of ore. In the fall of 2000, mining activities were suspended following a series of ground movements around the South Regional Pillar along weak geological structures. After extensive geotechnical investigations, a decision was made to carry out a mass destress blast in the West Ore Zone (WOZ) to cut the principal stress across an area of 135 m along strike and 86 m high. At the end of July 2001, the WOZ mass blast was successfully initiated. Following this success the mine decided to take a similar approach to destressing the North Regional Pillar (NRP). The final mass blast was taken in early February 2003. Advanced blasting technologies, including state of the art electronic detonators and blast simulation, played an important role in achieving the successful blasts. The high precision of delay timing and long delay duration of the electronic detonators ensured accurate and reliable initiations of over 800 blastholes in the WOZ mass blast. Orica?s DMC_Blast (Distinct Motion Code) simulation code was used to study different blasting blocks for the desired timing in the initiation sequence. This paper describes the process of applying electronic detonators in complex blasts, and discusses how blast simulation results were interpreted to guide engineering design of the mass blasts.

May 1, 2003

Building off the enthusiasm generated by Credit Suisse First Boston on the potential benefits of an industry-wide effort to market gold jewellery, a group of gold producers, led by Randall Oliphant, CEO of Barrick Gold, decides to investigate the long -term impact of launching a significant marketing initiative to stimulate demand for gold jewellery. The group establishes an international Steering Committee representing producers of differing sizes, members and non-members of the World Gold Council. This Committee comprises representatives from AngloGold, Barrick, Gympie Gold, Kinross, Randgold, and Sons of Gwalia and is supported by the Australian Gold Council, the Gold and Silver Institute, and CSFB. The Steering Committee hires McKinsey to assist it by conducting an independent review of whether investment in a large-scale marketing initiative for gold jewellery would be effective in increasing demand for gold, and ultimately of significant economic benefit of the gold industry. Based on McKinsey?s review* and its own discussions with key stakeholders across the industry, the Steering Committee strongly believes the case for marketing is compelling and sufficiently proven to persuade the industry to undertake a major initiative over the next few years. The Steering Committee, supported by McKinsey, conducts briefings with a range of gold producers to share its findings and to understand producers? perspectives on an industry-funded marketing campaign. The Steering Committee is asking for your support to bring this industry-funded marketing campaign to life.

May 1, 2002

By Walter Greaves

THIS paper describes a series of tests performed at the Hollinger mill during the past four years, in which both metal and rubber-lined pumps were used for pumping sand and slime. While conditions will not be the same at other mills, it is felt that the information gained from the tests should be of value to other operators and of assistance to them in selecting the most efficient size of pump and kind of lining for economical operation. For the successful operation of pumps with rubber linings there are certain conditions, which, if recognized at the outset, will save the operator a good deal of work and trouble. First is the necessity of keeping sharp pieces of steel, or anything that might cut the lining, out of the pumps. This can be effected by placing screens in the proper locations. Second is to recognize the fact that the rubber lining of the shell, and the rubber cover of the impeller, are subjected to very different conditions. The shell lining, :being at rest and well supported by the metal case, has a relatively easy job compared ? with the impeller covering, which is subjected to centrifugal force and has a tendency to tear itself away from the metal core. Also, the pulp travels through and past the impeller at a high velocity. These two factors, centrifugal force and velocity of the pulp, would appear to set a limit to the speed at which, for a given set of conditions, it is economical to run a rubber-covered impeller. Therefore, a pump should be large enough for the work to be done. To get the best mechanical efficiency, it must be operated somewhere near the limit of its capacity, but this may not give the best overall cost, because the saving in power, due to the high efficiency, may easily be lost through excessive wear on the lining. It would appear that this condition is more critical in a rubber-lined pump than in one lined with metal.

Jan 1, 1939