Search Documents

By Earl Gebhardt

"The planning and design of mining panels in the Potash Corporation of Saskatchewan Inc., Lanigan Division mine Block B involved a number of investigative techniques. The techniques utilized to gain insight into the viability of mining included2-D and 3-D seismic surveys, longhole drilling, exploration wells, photo lineament, magnetic and gravity surveys, and actual room excavation.IntroductionPotash Corporation of Saskatchewan Inc. (PCS) owns and operates four potash mines in the province of Saskatchewan. The Lanigan Division mine is located 110 Ian east of Saskatoon, Saskatchewan, near the town of Lanigan.The Lanigan Mine commenced production in August 1968under the ownership or Alwinsal Potash of Canada Limited. The mine was purchased by PCS in 1977.Lanigan Division's productive capacity is 3.4 million tonnes of product per year. Ore is extracted from the "" B"" zone or Layer III or the Patience Lake member of the Prairie Evaporite, more than 1000m below surface . The Patience Lake member (approximately 20 m thick) consists of potash interbedded with salt. The average run-of-mine ore grade is 21070 K20 (Fig. I).The mine was initially developed using the room-and-pillar technique. Improvements in mining resulted in the use or extensible conveyors in long panel rooms."

Jan 1, 1993

By J. C. Taylor, J. A. Davis

"Existing environmental, health and safety regulations have forced pyrometallurgical facilities worldwide to drastically change some of their traditional methods of operation. In extreme cases, a number of facilities have been closed due to their inability to conform to these existing regulations. Tougher future legislation and government policy will lead to more stringent regulations and enforcement policies. The efficient control of smelter secondary emissions will, therefore, become critical to successful smelter operation.Much attention has been paid to the smelter primary process off-gas systems, including the development of new process designs to reduce the number of uncontrolled transfer operations. However, even the most modem smelter design requires control of its secondary contaminant sources, which mayor may not be directly related to the process operation.This paper discusses some of the potential secondary emissions encountered in many of the present process technologies. A few of the emission sources presented are only periodic in nature, such as those caused by maintenance procedures, but which have the capability of forcing smelter shut-down because of their direct impact on worker health and safety. The paper deals with a variety of topics relating to the efficient control, maintenance and monitoring of secondary emissions in copper, nickel, aluminum, magnesium and lead smelters, as well as in iron foundries and steel making facilities. Examples of the typical problems encountered in each of the above process operations are presented, including fume control at furnace tapping and slagging locations, metal transfer stations, tapping launders, and ladle transfer operations. The parameters for the most efficient design of fume capture systems, problems encountered with the handling and clean-up of certain collected emissions, and examples of successful solutions in particular operations are discussed."

Jan 1, 1994

By Lar Liljeblad

"As demands upon the earth's natural resources continue to grow, exploration companies, mining organizations and others face the problem of the need to tackle increasingly more difficult strata to open up new reserves. Innovations in materials technology and tool design have steadily improved this capability, but none perhaps so drastically as a recently introduced cemented carbide in which tool wear resistance and/or toughness can be tailored precisely to the user's drilling needs.Introduction Until about forty years ago, the bulk of rock-drilling operations had to be carried out with hardened steels. Short life between re-grinds was common especially in abrasive rock formations. Shortly after World War II, Sandvik, Sweden, pioneered the development of sintered (cemented) carbide-tipped steel tools as a means of improving drill tool life. The new material was a composite of tungsten carbide and cobalt, the latter acting as a 'cement' to bind the wear-resistant carbide grains together, and the composite, in turn, was brazed to the steel. The immediate effect was a 100-fold increase in the service life of the tool.Intractable ProblemsWhile the carbide-tipped tools served the mining and quarrying industries admirably there were, nonetheless, some seemingly intractable limitations. The greater the wear resistance of the material - the quality for which it is selected - the more brittle it is. Also, rocks vary widely in hardness and abrasiveness and no single tool, either in terms of material or shape, meets every need. Specifically, for fast penetration of non-abrasive rock, toughness must be combined with a relatively sharp tool prome. Highly abrasive rock, on the other hand, demands a substantially broad area of extremely wear-resistant material on the tool if long bit life is to be assured. Between these extremes there are innumerable variations in rock"

Jan 1, 1991

By R. G. Bradbury

The paper uses two hypothetical, but typical, situations to show that hydraulic rock drilling equipment has very significant economic advantages over pneumatic equipment both in drifting applications (even in the situation where advantage is not taken of the high productive capacity of the hydraulic drill) and production drilling applications. Other factors, including the non-economic advantages and the disadvantages of hydraulic drilling, are discussed. The paper concludes with a brief analysis of why the Canadian mining industry has been slow to take advantage of this apparent broadly advantageous advance in rock drilling technology.

Jan 1, 1979

By A. I. A. Salama, M. W. Mikhail

"The existing methods of block diagram manipulation and vanishing variable for flowsheet simplification used in coal and mineral processing circuit evaluation and optimization cannot be easily implemented on digital computer.The signal flowgraph technique is proposed to represent and simplify determination of the relationship between intermediate or end variable and the feed in the flowsheet. Typical and existing circuits are used to demonstrate the application of the proposed technique which can easily be implemented on digital computers.IntroductionRecently there has been much interest in the analysis and optimization of coal and mineral processing circuits to assist in the pre diction of coal and mineral processing plant performance. The block diagram and the vanishing variable were introduced and utilized in the analysis of plant flowsheet. Although the block diagram approach is useful, it requires manual manipulation of the circuit block diagram which may present difficulties in the situation of complex circuits. Moreover, it may not be easy to implement on a digital computer.In this paper, the signal flowgraph technique is proposed to represent the circuit flowsheet and to simplify the determination of relationships between intermediate or end variables (fractional mass) and the feed for any coal and for any mineral processing circuit comprising size and density separators. These relationships are utilized in the analysis and/or optimization of the circuit. The proposed technique is illustrated by considering typical and existing circuits."

Jan 1, 1987

By J. C. Ingles

"A new technique is in the process of revolutionizing inorganic chemical analysis. Galled atomic absorption spectrophotometry, it combines the use of a special light source, a flame, and the equipment of conventional spectrophotometry, to provide a quick, reasonably accurate method for the determination of a large number of elements.This paper outlines the principles on which it is based, describes the commercial instrumentation"" available for exploiting it, and. summarizes current applications in process metallurgy."

Jan 1, 1966

By T G. Callcott

Australian coking coals are either class 434<tlj534<2l, at Port Kembla, or 634<3> at Newcastle. The former yield good blast-furnace cokes; the latter yield poor ones. However, increases in conventional strength indices, by methods applicable with normal coking ovens, seem unlikely to be economically attractive. Characterization of the coals has enabled an "economic" blend to be developed in the Newcastle area, and this has affected mining, preparation and handling operations. Coking studies have led to a specification for the making of strong coke, especially from the high-volatile Newcastle coals. Continuous coking studies, developed from the efforts to make very strong coke, have taken two directions. Firstly, coking thin layers of coal on strands; secondly, coking, in various types of vessels, compacts of coals with or with-out the inclusion of non-coking coals, iron ores or other inert materials. Gas, "sand" and hot metal coking have been tested for use in compact coking. Particular attention has been paid to pellets of coal and ore. The probable industrial problems in adopting any of the ideas are presently being examined.

Jan 1, 1963

By A. G. Eccles

Western Mines&apos; milling circuit produces three concentrates (copper, lead and zinc), with the tailings being disposed of at the bottom of Buttle Lake. In view of the mine&apos;s location and the method of tailing disposal, a comprehensive pollution control program has been in effect since start-up. Changes -in the ore over the past few years have required the use of increasing quantities of sodium cyanide in order to effect a good copper-lead separation. This led to the use of alkaline chlorination for destruction of ?residual cyanide and precipitation of dissolved copper contained in the tailing effluent. The development of Western Mines&apos; alkaline chlorination plant is discussed in detail, including initial test work and the evolution of procedures leading to the present operation. The current monitoring program is also reviewed.

Jan 1, 1977

By A. Christoffersson, T. Nillson-Wullf, H. R. Manouchehri

"Mining industry has been the building blocks for human development through millennia and will continue to play its role in sustainability and meeting society’s needs for raw material. In the way towards sustainability, the next generation of efficient and heavy duty of Sandvik’s crushers, CH860 and CH865, are introduced for efficient crushing. As the secondary, tertiary and/or pebble crusher, these new crushers are designed to over perform in tough mining environment. Featuring higher crushing forces relative to the mantel diameter and 500 kW motor, combined with advanced automation system, i.e., sophisticated HydrosetTM and Automated Setting Regulation (ASRTM), combined with overpressure system with dedicated air supply in dust collar, etc., the new crushers provide higher safety, productivity, and reliability with the same foot-print of conventional cone crushers.Since crushers are more energy efficient than mills it makes sense to effort in fine crushing to save energy and protect environment. That has been the logic behind development and introducing stronger and more efficient crushers by Sandvik. The results on crushing hard iron and gold ores by CH865 have proven its efficiency in fine crushing at a higher productivity, availability and reliability rates through increasing throughput for defined size fraction and extended crushing chamber liner life.Within this paper the performance of the CH865 to deal with two different ores are presented discussed with a glance at how the downstream milling process can be benefited by saving energy and reducing the operation cost. In plant practice, the implementation of the new CH865 provides between 25 and 30% of the crushed ore in the size range of first step milling, i.e., < 2 mm, that offers opportunity for reduction in energy consumption in milling and even changing the process plant configuration by directly forwarded that part to gravity separation. Furthermore, potential of converting the rod mill to ball mill to improve productivity has been considered by plant engineers. Furthermore, some potential applications for such efficient crushers are brought into considerations and discussed. The new developments provide about 30% higher crushing force to efficiently deal with competent ores and pebbles. The CH860 and CH865 crushers are well suited to replace conventional secondary and tertiary crushers respectively; nevertheless, CH865 is virtual option for pebble crushing in SAG and AG milling circuits."

Jan 1, 2016

By Noel G. Thomas

"This paper will identify where the industry is heading with iron· ore in the next ten years. From a customer&apos;s point of view, an indication of the changing, yet expanding, market will be made. This will progress further into the most likely changes in chemical and physical requirements of the ore products. No definite target can be set for 1990, but the logic from the direction of the changes will be established.IntroductionThe tonnage and quality of iron ore produced in the eighties will be heavily influenced by energy and investment considerations. That&apos;s not a great pronouncement, but this paper will explain how these two factors are :(I) influencing a disproportionate growth of electric furnace capacity and a greater use of scrap for iron units, in place of Iron ore;(2) influencing chemistry specifications; and(3) causing extensive examination of ore agglomerate form. Inflating investment costs are emphasizing the need for more productive blast furnaces, and the iron ore burden is under heavy examination as to how it affects productivity and coke rate."

Jan 1, 1981

By Robert B. Parsons

"The Whitehorse Mining Initiative (WMI) brought together all of the key stakeholders in Canada&apos;s mining industry to develop a framework whereby the industry can meet the challenges that it faces into the 21st century. The WMI Accord7 which was signed at the annual Mines Ministers Conference in Victoria, British Columbia, on September 137 1994, touches all of the important issues that confront the industry, including taxation. IntroductionSeptember 13, 1994, was a historical day for Canada&apos;s mining industry. On that day, on the occasion of the annual Mines Ministers Conference in Victoria, British Columbia, the Whitehorse Mining Initiative (WMI) Accord was signed by the leaders of the five principal stakeholders in the industry: industry; government; labour; environmentalists; and aboriginals. The Accord is the culmination of two years of hard work and intense collaboration by these stakeholders. But, the Accord is not the end result. The Accord can better be described as a springboard to a prosperous future for mining in Canada.The WMI had its beginnings at the Mines Ministers Conference in Whitehorse, Yukon, in September 1992 (hence, the name of the initiative). At that time, the mining industry was well aware of the serious challenges facing the industry, including significantly increased competition for mineral investment from other mining countries, coupled with an atmosphere of uncertainty surrounding land access, environmental regulations, and taxation. The diversion of investment abroad was hurting, and would continue to hurt, all Canadians. Something had to be done. At the 1992"

Jan 1, 1994

By A. B. Carino

Gulf Minerals (Canada) Limited&apos;s Rabbit Lake uranium operation is located in the northern portion of Saskatchewan, 198 miles southeast of Uranium City and /34 miles northwest of Lynn Lake, Manitoba. The paper follows the ore flow through crushing, grinding, sulphuric acid leaching, countercurrent decantation, solvent extraction, ammonium diuranate precipitation, thickening, drying and tailing neutralization.

Jan 1, 1979

By Robert B. Parsons

"In this period of improved metal prices and reported profits, valuable lessons should be recalled from the 1970s when a similar cycle lured the federal and provincial governments into thinking that they could grab bigger pieces of the pie without harming the minerals industry. It took years for the industry to recover from the damage inflicted by that unprecedented scramble for higher tax revenues. It is hoped that the current policy makers will have learned from the lessons of the seventies, and will realize that mining companies need to keep a reasonable share of profits realized during the good years in order to prepare for the inevitable downturn in the cycle.INTRODUCTION"", «. We have made clear to industry that super profits... will no longer be tolerated "".With that assertion, the Honourable David Barrett , Premier and Minister of Finance of the Province of British Columbia, announced the introduction of a new mining tax regime in his February 17, 1974 bud get papers . British Columbia producers would face a basic royalty and a royalty on so-called ""super profits"", resulting in some instances in tax rates exceeding 100070 of pre-tax profits.The ball started to roll. Mining tax changes knew no political or geo graphical boundary. On April 9, 1974, Ontario&apos;s Treasurer John White stated in his budget speech:""Increased demand by major industrialized countries has resulted in sharply higher metals prices and substantial wind fall gains for the mining industry in Ontario. With the prospective demand for minerals likely to sustain current price trends into the future, it is only fair that we secure for the people a higher return from our natural resources""."

Jan 1, 1989

By P. Karimi, A. Amini, H. Abdollahi, A. Mirzaeian

Due to detrimental effects of cyanidation process on the environment in gold industry, application of cyanide alternatives such as thiourea are being highly considered in recent projects. In this study, the extraction of gold from poly metal ore, using thiourea was precisely investigated. The representative sample contained 2.5 ppm Au and 160 ppm Ag. The sample was categorized as oxide gold ore, because the main part of its pyrite was changed to iron oxide and hydroxide such as goethite and lepidocrosite. According to mineralogy, the main gangue mineral was quartz. It shows that gold grains are free and interlocked with quartz matrix. Also, the presence of a high amount of silver in free and sulfide forms and also the low content of other sulfide minerals such as base metal sulfides is a remarkable point of these studies. In the gold extraction process with thiourea, there are several parameters that affect the rate of gold dissolution such as concentrations of thiourea as a gold lixiviant and ferric sulfate as an oxidant, pH and size fraction of feed and leaching time. The influence of these parameters on the gold dissolution rate were investigated and optimized. The results showed that the concentration of thiourea is the most influential parameter which could increase the gold recovery to 71% (at 10 g/kg sample). The optimal amount of ferric sulfate was determined as 6 g/kg sample. Also, the optimal levels of size fraction of feed and pH of solution were 88% under 75 micron and 2 as acidity; respectively. Leaching time was 6 hrs. In addition, this sample was leached with cyanide and the optimized values of size fraction of d88=75 microns, pH=10.45, 2500 ppm of sodium cyanide with time leaching of 24 hours were concluded for maximum recovery of gold in solution. Finally, the results of cyanidation tests were compared to the thiourea dissolution after optimizing all affected parameters in cyanidation process.

Jan 1, 2016

By Robert B. Parsons

"Ontario and Quebec taxpayers will have to dig deeper into their pockets to pay more tax, according to budget papers tabled in these provinces in May 1993. Individuals will be hardest hit, but corporations will also have to ante up in the face of higher rates, reduced deductions, and new taxes.Up, up, and away...Somewhere in the bleak picture of the 1993 Quebec and Ontario budgets, there is a bit of good news for the mining industry.Careful scrutiny reveals:• Ontario will correct a capital tax provision which inadvertently penalizes flow through share issuers;• Quebec&apos;s flow-through incentives will be extended to December 31, 1995; and • both Quebec and Ontario will allow deductions for mine site reclamation payments.The industry may also find some comfort in the fact that Ontario&apos;s new corporate minimum tax will be profit-based (unlike the federal minimum tax), so that non-producers should not face a liability for this tax. There is some concern though, about Quebec&apos;s announcement that the refundable credit mechanism in the Mining Duties Act will be reviewed."

Jan 1, 1993

By Alan G. Galley

"Advances in our knowledge of the petrochemical attributes of deposit environments and of the character and extent of hydrothermal systems associated with certain deposit types has resulted in increased application of lithogeochemistry to exploration programs. Lithogeochemistry can be used to vector an exploration program toward an area of high potential through the use of a series of collapsing scales of analysis from a tectonic subprovince down to a particular stratigraphic segment. In the case of volcanogenic massive sulphide (VMS) deposits this involves the recognition ofsuitable volcanic domains, and the identification of subvolcanic intrusions and cogenetic felsic extrusive complexes. The recognition of chemical vectors within regional-scale alteration zones and associated chemical sedimentary rocks allows the geologist to identify the stratigraphic units with the most potential for hosting a base metal deposit.An integrated lithogeochemical program requires the judicious use of major, trace and rare-earth element and isotopic analysis. Standard discriminant plots may be employed to identify suitable tectonic and lithologic environments. Analysis of the chemical and mineralogical variations in broad-scale, semi-comfortable alteration zones provides a useful set of vectors to VMS mineralization. These may include contouring raw data, element ratios on XY plots, normalizing data against known rock values, or calculating mass changes in alteration zones."

Jan 1, 1995

By A. R. Trusiak, C. Bazin, D. Hodouin

"The On-Stream Analyzer has proven, and is still proving to be, an extremely valuable tool for the control of flotation circuits. This paper examines the possibility of going further in the utilization of the analyzer results by using a real-time material balance program to calculate the mass flow rates within the streams of a circuit for process control, analysis and optimization as well as for the detection of sensor malfunction. The material balance algorithm improves measurements and give good estimates of unmeasured variables during normal operating conditions. The potential and limitations of the method are illustrated using results of an application to the Line 3 flotation circuit of Brunswick Mining and Smelting, New Brunswick.IntroductionThe On-Stream Analyzer (OSA) has gained, over the last two decades, the status of key instrument for the control of flotation plants. The OSA is currently used in almost every sulphide flotation plant and its application in oxide mineral flotation plants isincreasing. Commercial OSAs include a sampling system that collectssamples from various streams of a circuit and exposes thesamples to an X-ray beam. The sample then generates X-ray pulsesthat are converted into assays using multilinear regression programs(Leroux and Franklin, 1994). The estimated assays arepassed to the flotation operators via operator consoles, or to controlloops of various degrees of complexity (McKee, 1991), whichmanipulate reagent addition, aeration rate or froth thickness toensure an adequate operation of the plant. Although this applicationrapidly pays for the purchase of the OSA, one should ask:""Could we get more from the OSA?"""

Jan 1, 1995

By J. Donovan

Underhand cut and fill mining is being planned for selected areas at the David Bell Mine where high ground stresses have resulted in particularly challenging mining conditions. In order to test the placement and performance of a variety of underhand cut and fill paste mats three different designs have been installed and extensively instrumented along the A-Zone 9C ore sill. The sill is approximately 87m long, 4.0m high, and 5.0m average width. The sill was broken into 3 sections each of which will contain one of the sill mat designs. The underhand sill will be mined 3.75mW x 4.0mH, allowing for some overbreak while minimizing the risk of the back span exceeding the design limit of 4.0mW. Each test sill mat includes pre and post-support and includes 0.5m (18?) broken muck mat placed along the sill floor. Upon developing beneath these mats quantitative and qualitative measures will be used to determine which design is the most suitable for application in underhand mining at David Bell.

May 1, 2007

By D. A. Peterson, R. Pakalnis, G. Peter Mah

"Laboratory and trial installations have been completed to determine the potential of composite cable bolt reinforcement in Canadian underground mines. Several prototypes of glass fibre cable bolts have been developed and tested, two of which are currently available to the mining industry. Their evalualtion consisted of lab testing in Canada and the United States, along with trial installations in several underground mines throughout Canada. The objective was to develop a cost competitive composite cable bolt equivalent in strength to that of a 16 mm (Ys in.) diameter steel cable bolt. In addition to achieving equal or superior load carrying characteristics in tension, the glass fibre cables generally experienced an increase in the rate of installation due to their lighter weight. Unlike conventional steel cables, composite cables may be installed within mines which utilize continuous excavation and which require cuttable support. A market analysis of cable bolt usage in Canada has been completed. Glass fibre cable bolts are an effective means of rock reinforcement in mining applications. They prove to be a viable alternative to conventional steel cable bolting. IntroductionCurrent cable bolting practice consists of cement grouting one or more steel cables within a drill hole in order to support the surrounding rock mass. Cable bolts are a form of internal support and are generally used as pre-support in open stope and cut-and fill mining methods. They can be either tensioned (active support) or untensioned (passive support) and may be of any length, though for underground mining applications, are generally less than 20 m (65.6 ft) and are untensioned. A major advantage of cable bolts is that they are flexible and can be coiled to approximately 1 m (3.3 ft) diameter coils. This allows relatively long lengths (>20 m, [65.6 ft]) to be installed in areas with limited head room (1.8 m)."

Jan 1, 1994

By D. Stone, N. J. Aslin, W. Webb

In today&apos;s modem copper electro-refineries, increasingly higher average current densities are being employed. With these increases many refineries are approaching their limiting current density. The nearness of the average operating current density to the limiting current density has placed increasing emphasis on the need to maintain an even current distribution. This paper explores the importance of maintaining even current density and discusses the factors, processes and practices that are necessary to achieve and maintain high quality production at high operational intensity.

Jan 1, 2005