Search Documents

By O. Neves, C. G. González Beca, M. C. Sol Pereira, H. Sousa Vale, R. A. Guedes de Carvalho, M. N. Sampaio

"As sulphide ores are usually concentrated by flotation , the material is very finely ground <37um), wet and impregnated with the chemicals used in flotation. These conditions are favourable to the development ofchemical reactions which are largely influenced by atmospheric conditions (temperature, humidity, wind, etc.) as well as by the geometry of the piles.Physical and chemical properties of a chalcopyrite concentrate were determined by laboratory tests. The knowledge of these properties was considered necessary in order to establish a correct design of the storage and handling operations of the sulphide ore concentrates obtained by flotation.The properties studied in this work were: transportable moisture limit, flowability, effects of vibration, hygroscopicity, ""caking"", chemical alterations by humidity, oxidation and self-heating (auto-ignition, dry and wet oxidation, self-heating by humidification and its prevention).INTRODUCTIONIn order that the handling and the transport of a powdered material may be carried out correctly, it is necessary to know certain physico-chemical characteristics. Transportable moisture limit (TML), apparent density (both aerated and compacted), compressibility, angle of repose, angle of spatula, cohesion and angle of slide(l-4) are characteristics (among the flowability parameters) worth knowing.Moisture content of the powdered material is fundamental, because if this is too low heavy losses will occur when the product&apos;s particle size is very small, if it is too high, separations between solid and liquid phases may occur. In the latter case, the centre of gravity of the system may change suddenly and cause accidents, mainly if transport is by sea or by river."

Jan 1, 1989

By E. M. De Souza, A. M. Coode

"When Canadian potash was brought into production in the 1960s substantial research was carried out to develop the technology needed to cope with the unique conditions in Saskatchewan mines. The intense research has established Saskatchewan&apos;s position as a leader in production technology on a world scale, and as a leader in setting international standards for potash production. The industry is now more than two decades old and, although the mines operate efficiently, there are a number oj prominent areas of concern. High among these is the prediction, prevention and control of sodium rich brine inflows. Control has proven difficult or elusive in the potash mining horizon, but work continues in this area. Control of brine in the superincumbent limestone formation has proven to be easier and more conclusive.The first part of this paper describes the rehabiltation, diamond drilling, and grouting completed at Central Canada Potash, which reduced the brine inflow from approximately 82 l/min . at the beginning of the work to O.9/1min. when the backfilling was placed.The second part of the paper describes the rationale for choosing the rock mechanical instrumentation, the reasons for their placement and the rock mechanical data recorded with some interpretation.IntroductionCentral Canada Potash is located approximately76 km southeast of Saskatoon, near the Yellowhead Highway. The commercial production of potash at CCP started at the end of 1969 at a depth of 1021m below surface. The potash zone, which is presently mined, is approximately 3.35 m thick . Stress relief methods using yielding pillars are used in the design of the mining layouts. The planned extraction ratio averages 35070 . The mine is designed to produce approximately 3.3 million tonnes of sylvinite per year to give approximately 1.3 million tonnes of finished product (muriate of potassium) per year."

Jan 1, 1990

By W. J. Kuit

"Complex facilities which provide for the collection, management and treatment of effluents emanating from the Sullivan mine and concentrator tailings were made operational in October 1979. Key features of the system are the use of upgraded tailings ponds for the storage of up to 800 million litres of metals-contaminated effluents, a treatment plant employing lime in a high-density sludge process and a sludge-impoundment facility designed for maximum long-term environmental safety. The completed works are capable of satisfying a difficult range of operating requirements imposed by highly variable weather conditions, drainage flows and soluble metals loadings. Final capital expenditures for the project approached $10 million and annual operating costs are about $0.8 million.This paper discusses the Kimberley effluents treatment project and the major considerations in its development. The treatment process, major plant equipment and initial operating experience are also described.IntroductionCominco Ltd. has worked the Sullivan orebody at Kimberley, B.C. since 1909 and has operated a concentrator some 5 km distant from the mine since 1923. Over the last 70 years, in excess of 120million tonnes of ore have been mined, and production continues at an average rate of 6,500 tonnes per day. It is a well-known fact that the contribution of this operation to Canada&apos;s mining industry and, in particular, Cominco&apos;s development has been significant. However, this success has not been without some undesirable side effects.Unfortunately, the Sullivan is one of only a few major Western Canadian orebodies which may be classed as ""acidic"" in nature. That is, the primary economic minerals, galena and marrnatite, are enclosed in a siliceous host rock with abundant pyrrhotite, but with little or no accompanying alkaline gangue minerals such as calcite and dolomite. The unavoidable consequence of mining such an ore is that contact with air and water generates an acid mine drainage containing various soluble metals orginally present as minerals.This problem also arises in the concentrator&apos;s tailings ponds, which, in the case of the Sullivan, are two separate impoundments of different materials. The 1,100 tonnesl day of ""iron"" tailings are primarily pyrrhotite which is surplus to the requirements of a separate operation that produces sulphuric acid as an intermediate to phosphate fertilizers. Inert gangue minerals with only a minor sulphide content are the main constituents of the 1,200 tonnes/ day of siliceous tailings. Corresponding to the relative proportion of sulphides in the solids, the decant from the iron tailings is substantially more contaminated than that from the siliceous pond."

Jan 1, 1980

By M. P. Tixier

Abstract In a review of the application of electrical logging in Canada, examples are .given of long and short distance correlations by means of the electrical logs. The use of MicroLogging for the determination of permeable and porous formations is explained. The question of log analysis for the quantitative determination of fluid saturation and porosity is .discussed. An example is provided to illustrate the significance of the resistivity gradient. The advantages of the new method of the Laterolog are shown, chiefly for the case of wells filled with high-salinity mud. Introduction Electrical logging techniques developed rapidly in Canada at the time an intensive drilling activity started for the exploitation of the Devonian series in Alberta, namely, at the beginning of 1947. The conventional service was soon thereafter supplemented with the latest technica1 improvements. Canada has been among the first regions to take advantage of MicroLogging*, which has proved a most powerful .tool for the investigation of permeable and porous formations; also, the more recent development known as the Laterolog has ?been introduced in Canada. The Laterolog provides a better determination of .the formations, particularly in the case of salty mud where the conventional logging is greatly handicapped. The various methods of electrical logging are now commonly known in oil industry and have been described in numerous publications ( 1) ( 2) (3).

Jan 1, 1951

By A. D. Hunter, J. M. JR. Moore

"The Aldermac deposit and associated prospects occur in the Noranda Archean volcanic centre of the Abitibi greenstone belt. Over two million tons of are grading 1.65% copper, with minor gold and silver, were mined between 1933 and 1943. The deposit has features in common with the Vauze and Millenbach mines in the same district.Recent detailed mapping, geochemistry and petrography combined with data from former diamond drilling and mining operations permit a re-interpretation of the Aldermac area. The orebodies and spatially related sulphidic zones are con eluded to be volcanogenic.The host rocks are a chemically bimodal suite of mafic and rhyolitic flows, volcaniclastics and related subvolcanic intrusions. Massive sulphide lenses are spatially related to a quartz-feldspar- phyric rhyolite dome and siliceous, volcanic-exhalative sedimentary rocks, The succession is cut by gabbro and syenite, related to later stages of volcanism, and by post Kenoran diabase dykes. Regional metamorphism attained the low greenschist facies, but the rocks lack penetrative deformation.Hydrothermal alteration is primarily an intense silicification of mafic volcanic rock s enveloping, or lying below, sulphidic zones. Chlorite and sericite alteration zones, including dalmatianite, are more locally developed and have a closer spatial relation to mineralization, as do epidote, calcite and calcic garnet.The structure is complex and cannot be explained by isoclinals folding; rather it reflects concurrent faulting, and extrusive and intrusive activity. Fault blocks were rotated and exhibit opposed facing; the original selling was possibly a submarine graben.Sulphidic zones occur within mafic and felsic volcanic rocks and at the interface between the two; there is thus potential for discovery throughout the known stratigraphic succession. Exploration conducted according to a volcanogenic model is advisable, particularly in the light of recent discoveries in similar rocks of the Amulet area."

Jan 1, 1983

By S. Masambi, S. M. Bradshaw, C. Dorfling

The presence of iron in base metal leach solutions complicates nickel and copper recovery processes. Leach solutions are commonly purified by precipitating iron as hematite, jarosite or goethite. Fast oxidation of ferrous to ferric is an important step to remove iron by precipitation at low pH values. This study reviews the ferrous oxidation mechanism and reaction rates in chloride media using molecular oxygen. This work contributes to the development of a better understanding of iron precipitation processing steps, which continues to be an important matter in hydrometallurgy. The specific objectives were to investigate (1) the effect of key process variables (acid concentration, copper concentration, and temperature) on the rate and extent of ferrous oxidation by dissolved oxygen and (2) the oxidation mechanism by varying chloride and hydrogen ion concentrations separately. Batch oxidation tests were performed using synthetic chloride solutions containing 45 g/L Fe and 3 g/L Ni at 50 and 80°C, dissolved Cu concentrations (0.3 to 3 g/L) and HCl concentrations (2 to 4.6 M). Regression analysis indicated that the significance of the effect of different variables on the extent of oxidation achieved after five hours decreased in the following order: HCl concentration > Cu concentration > temperature. Increasing the HCl concentration from 4 M to 4.6 M caused the degree of oxidation achieved after two hours to increase from 58.3% to 98.1%. The catalytic effect of dissolved copper on ferrous oxidation was more significant at low acid concentrations. Experimental data suggest that rapid oxidation of ferrous is possible at high HCl concentrations for two main reasons. First, the formation of ferrous chloride complexes allows ferrous oxidation to proceed without the formation of superoxide as an intermediate product (the rate limiting step in dilute acid solutions). Second, the formation of ferric chloride complexes stabilises the oxidation product.

Jan 1, 2016

By R. D. Brown

"Concerns over possible additional involvement of governments in Canada&apos;s mining industry and its adverse effects on the industry &apos;s growth were a frequent topic of conversation at the recent Annual General Meeting of the CIM.Still painfully fresh in the minds of industry leaders are the disastrous results of the federal/provincial scramble over resource revenues which followed the relatively high metal prices witnessed in 1973/1974. At current metal prices, it is not surprising, then, that a nagging fear persists that these governments may once again restructure tax and other rules to the detriment of the industry and the country.This month, Tax Notes recalls some of the progress which the industry and governments have made in 1979 in the taxation of the resource sector, and urges that higher metal prices be viewed in light of the costly exploration, development and production efforts which will be required for the industry to continue to play its important role in our economy.IntroductionAt the Annual General Meeting of The Canadian Institute of Mining and Metallurgy, held in April, 1980, it was abundantly clear that there is widespread concern in Canada&apos;s mining industry that this country&apos;s tax regime may once again be blasted by ill winds of change.A stable and more favourable tax climate, as well as higher metal prices and profits, made 1979 almost a golden year for Canadian mining. However, from the tax viewpoint at least, there are some spots on the silver lining as apprehensions grow that the well-heralded battle between federal and provincial governments over oil and gas may spread to the mining sector, with serious damage to the industry and its newfound federal-provincial cooperation."

Jan 1, 1980

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed.The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grade, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the final cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure I."

Jan 1, 1995

By K. Hashiba, Y. Z. Liang, K. Fukui, M. Koizumi

"Efficiency and penetration rate during percussive rock drilling significantly affect the speed of tunneling and excavation. Many researchers and engineers have continuously engaged in the advancement of rock drilling performance. Development and modification of the rock drills based on test data are timeconsuming and costly. Hence it is essential to make effective use of numerical simulation. However, most of the numerical models proposed in previous studies were too simple in comparison with the actual percussive rock drilling in which many factors are involved. The objective of our research project is to construct a new realistic numerical model of continuous percussive drilling, which is based on the previous Okubo-Nishimatsu’s model. In this study, the parts of the previous model involved in stress wave propagation and attenuation were modified. The two models were prepared for HD712 hydraulic rock drill mounted on crawler drills and HD210 hydraulic rock drill mounted on drilling jumbos. Stress wave propagation was computed with the discretized one-dimensional wave equation. The calculated results were compared to the stress waves measured on a rod during percussive drilling. In both models for HD712 and HD210, the measured stress waves can be reproduced with the one-dimensional model of the same acoustic impedance as the actual piston, shank rod and rod combined with the CI+spring model as a rod joint. The calculated results indicate that the spring constant in the model of a rod joint needs to be set appropriately depending on drilling conditions. INTRODUCTIONEfficiency and penetration rate during percussive rock drilling significantly affect the speed of tunneling and excavation. Many researchers and engineers have continuously engaged in the advancement of rock drilling performance. Components related to the percussive drilling are a drill body, a piston, a shank rod, rods, rod joints, a bit and rock. The piston in the drill body is reciprocated by hydraulic pressure and collides with the shank rod a few thousand times per minute. Stress waves generated by the collision propagate and attenuate in the rods and rod joints, and then reach the bit. The bit penetrates and crushes rock. During percussive drilling, the components mutually affect each other and self-induced oscillation occurs. The number of blows and the rate of penetration are determined by the practical drilling conditions such as hydraulic pressure, thrust force, number of rods and mechanical properties of rock. Development and modification of the rock drills based on test data are time-consuming and costly. Hence it is essential to make effective use of numerical simulation. However, most of the numerical models proposed in previous studies were too simple in comparison with the actual percussive rock drilling in which many factors are involved."

Jan 1, 2015

By Bruce C. Fielder

"The concentration of uranium in orebodies discovered in the Athabasca Basin of northern Saskatchewan over the last 20 years has increased by a factor of 100. These high grade uranium orebodies are associated with high concentrations of radionuclides, complex mineralogy and an elemental makeup that includes base metals, arsenic, and molybdenum. Exploiting these high grade ores has required metallurgical advances in milling, tailings disposal and effluent treatment as well as changes in the design of uranium mills.This paper describes the most significant advances, including advances in dealing with the environmental issues which have become more prevalent in recent years. The milling processes of the Cluff Lake Mill, Key Lake Mill, Rabbit Lake Mill, and McClean Lake Mill are compared to illustrate both similarities and differences necessary for milling different orebodies.BackgroundUranium mining in Saskatchewan started in 1953 when the Beaverlodge Mine, owned by Eldorado Nuclear Limited (Eldorado), came into operation at Uranium City. Development in the Athabasca basin started in 1975 when the Rabbit Lake mine came into operation. This was followed by the start-up of the Cluff Lake mine in 1980 and the Key Lake mine in 1983. The McClean Lake mine is forecast to start up in the near future. The McArthur River mine recently received construction approval and the Cigar Lake Project and the Midwest Project are currently in the environmental approval process.The Beaverlodge operation ceased production in June 1982 after nearly 30 years of operation. The Rabbit Lake mill processed Rabbit Lake ore from 1975 until 1985, Collins Bay R-Zone ore from 1985 until 1993, and is currently processing ore from the Eagle Point mine (Bharadwaj, Jarvi and Lam, 1996). The Cluff Lake mill processed ore from the D- Orebody from 1980 until 1984. Since then the Claude orebody has been processed and the OP and DS orebodies are presently being milled (SRK. Senes and Melis, 1987; and Cogema Resources Inc. 1994 ). The Key Lake mill processed ore from the Gaertner ore body from 1983 until 1989 and Deilmann ore has been processed since (Cameco Corporation, 1992b and I 994a). Processing of McArthur River ore in the Key Lake mill is scheduled for 1999. The McClean Lake mill will be processing ore from the JLR, Sue and McClcan orebodies associated with the McClean Lake mine. In future ore from the Cigar Lake and Midwest projects will be processed in the McClean Lake mill. (Minatco Limited. 1991a)."

Jan 1, 1998

By J. E. Nesset

"This paper discusses the importance of considering residence time distribution (RTD) in the design of flotation and mixing circuits and in the analysis of operating problems. The experiences and successes of Brunswick Mining in this area are covered and include: the development of a practical RTD measurement technique using pulp conductivity, baffle installation to improve the RTD of existing process equipment, and the method in which RTD considerations have been used to design the newest flotation and conditioning operations IntroductionThe use of residence time distributions (RTDs) in the design and analysis of unit operations is well understood by the chemical engineering profession in while mineral processing engineers have tended to rely on empirical and rule-of-thumb factors. For example, in scale up from laboratory and pilot test results to full size flotation plant design, empirical rule s are often used to establish residence time and number of cells in the bank. Coleman suggests a factor of at least 2, and up to 5 for gold ores, be applied to laboratory determined flotation times. This is further illustrated in Table I, taken from Denver equipment. The number of cells in series to achieve the required retention time while minimizing short-circuiting has generated a variety of conclusions (Table 2). Obviously there is less than complete agreement on the subject. Young notes that a clear difference of opinion has emerged and cites as extremes, (i) the publications of Outokumpum showing unimpaired recovery for its largest machines (38 m3) compared to equivalent retention times for numerous smaller machines, and (ii) the experiences of Eastern European countries where the practice is to install banks of 30 unit s or more, operating in series, often with unit retention times of only a fraction of a minute.The empirical factors used by engineers presumably account for other than tested feed conditions, inefficiencies in large continuous machines, inevitable day-to-day circuit disruptions, gradual equipment deterioration and any other safety factor the engineer feels compelled to incorporate. An understanding of RTD concepts and techniques should help the practicing mineral engineer to develop more soundly based factors. Thi s paper relates the experiences of Brunswick Mining in using RTD techniques in the unit operations of flot ation and mixing"

Jan 1, 1988

By J. E. Nesset

"This paper discusses the importance of considering residence time distribution (RTD) in the design of flotation and mixing circuits and in the analysis of operating problems. The experiences and successes of Brunswick Mining in this area are covered and include: the development of a practical RTD measurement technique using pulp conductivity, baffle installation to improve the RTD of existing process equipment, and the method in which RTD considerations have been used to design the newest flotation and conditioning operations. IntroductionThe use of residence time distributions (RTDs) in the design and analysis of unit operations is well understood by the chemical engineering profession in while mineral processing engineers have tended to rely on empirical and rule-of-thumb factors. For example, in scale up from laboratory and pilot test results to full size flotation plant design, empirical rule s are often used to establish residence time and number of cells in the bank. Coleman suggests a factor of at least 2, and up to 5 for gold ores, be applied to laboratory determined flotation times. This is further illustrated in Table I, taken from Denver equipment.The number of cells in series to achieve the required retention time while minimizing short-circuiting has generated a variety of conclusions (Table 2). Obviously there is less than complete agreement on the subject. Young notes that a clear difference of opinion has emerged and cites as extremes, (i) the publications of Outokumpum showing unimpaired recovery for its largest machines (38 m3) compared to equivalent retention times for numerous smaller machines, and (ii) the experiences of Eastern European countries where the practice is to install banks of 30 unit s or more, operating in series, often with unit retention times of only a fraction of a minute.The empirical factors used by engineers presumably account for other than tested feed conditions, inefficiencies in large continuous machines, inevitable day-to-day circuit disruptions, gradual equipment deterioration and any other safety factor the engineer feels compelled to incorporate. An understanding of RTD concepts and techniques should help the practicing mineral engineer to develop more soundly based factors. This paper relates the experiences of Brunswick Mining in using RTD techniques in the unit operations of flotation and mixing."

Jan 1, 1988

By Karl J. C. Harries

"3.1. INTRODUCTIONThis chapter discusses briefly the common law concepts of fiduciary relationship, constructive trust, and breach of confidence. Following a discussion of confidentiality agreements, the last section of the chapter compares and comments on two common law cases, the LAC Case and the Metalore Case. Civil law readers should not ignore this chapter or § 3.5. the comparison as, to a large extent, the concepts and comments are universal, even though the procedures for applying them may vary.1It should be appreciated that, regardless of the legal system, if the Court sees that a wrong has been done, it will attempt to right that wrong, either by awarding monetary damages against the wrong-doer to compensate the injured party or by attempting to make the injured party whole again by such means as negating an agreement (as in the Metalore Case) or returning property to a wronged party (as in the LAC Case). The methodology for accomplishing either of these results will vary with the jurisdiction, and the two are not mutually exclusive.These two Ontario cases have been chosen, not because they are the only ones available – they certainly are not – but because both are relatively well known within the minerals industry and they deal with problems that may face any explorationist (although it is to be hoped that the facts of the Metalore Case do not represent “normal” behaviour). Each judgment offers useful guidelines, as well as insight into a judge’s approach to problems, the type of information he expects to receive, how his mind works, and, particularly in the Court of Appeal judgment in the Metalore Case, how he might reason through and “justify” his decisions.3.2. SOME LEGAL CONCEPTS In order to appreciate some of the matters discussed in this chapter, it is necessary to have some idea of the common law considerations of fiduciary relationships, constructive trust, and breach of confidence."

Jan 1, 2003

By Ross L. Sherlock, David J. Scott, Gordon MacKay, Wayne Johnson

"Abstract - The demographics of Nunavut indicate a very young and poorly educated population spread over wide areas in small isolated communities. The current economic sectors will be unable to expand and meet the demands of this emerging workforce. Given the realities of Nunavut, the most promising direction in which the economy may expand is through mineral development. The Nunavut Land Claims Agreement (NLCA) has established the legislative framework for sustainable development in Nunavut through mineral development. The NLCA has transferred ownership for much of Nunavut’s potential mineral resources to beneficiaries of the lands claim. Royalties generated from mining operations on subsurface Inuit-owned lands, and to a lesser extent on Crown land, will flow back to beneficiaries of the lands claim through their administrative company, which may then be invested in the communities. Additional benefits of mineral resource development in Nunavut will be realized through impact and benefit agreements.To realize the benefits from mining operations, Nunavut has to be able to attract and support exploration and development companies through the release of high-quality geoscience data. However, due to Nunavut’s isolation and the expense of conducting geoscience fieldwork, the jurisdiction lags far behind the rest of Canada in terms of quality and quantity of government geoscience. About 70% of the territory is inadequately mapped to attract exploration companies or to make informed land-use decisions. The role of government-funded geoscience in Nunavut is to stimulate exploration and discovery through new framework mapping and focused thematic projects. The timely delivery of high-quality geoscience products will attract exploration companies to Nunavut and further their efforts to discover and develop mineral resources in order that the subsequent benefits of this activity may flow to the beneficiaries of the NLCA as well as all other residents of Nunavut."

Jan 1, 2003

By Lorne Sivertson, Peter Kitrredge

"World metallurgical coal imports totalled 110million tonnes in 1978. Of this amount, Japan imported 50 million tonnes, making it by far the largest and most important coking coal market . British Columbia and Alberta exported 12.0 million tonnes of coking coal in 1978, or 11% of the world total. Virtually all of these exports were directed to Japan, making up 22% of total imports.Some observers have suggested that because Japan is almost the exclusive buyer of British Columbia and Alberta metallurgical coal, the benefits of the coal trade may be primarily on the side of the powerful Japanese buyers. Buttressing this suspicion is the fact that Japanese trading companies have taken substantial equity positions in B.C. coal mines, thus presenting the possibility of non-arms-Iength transfer arrangements. There is then at least some evidence to support the hypothesis that Canada&apos;s western coal producers receive prices that are less than would prevail in a more competitive market; that is, that they are exploited.This paper produces evidence that Canada&apos;s coals are not underpriced in respect to U.S. and world markets. The conclusion is drawn that British Columbia and Alberta metallurgical coals receive prices that are equal to prices known to be competitively determined. This conclusion follows an in-depth analysis of prices, coal qualities and the economic characteristics of all major coals traded in the Japanese market. A by-product of the analysis is an equation capable of predicting the value of any metallurgical coal sold to Japanese buyers, or, for that matter, any buyer. Hopefully, this can be of some use to coal producers in developing their marketing strategies."

Jan 1, 1980

By J. A. Finch

"This paper describes major technical developments in rod mill design and operating practice since its introduction into the North American minerals industry over fifty years ago. The basic operating characteristics of the wet, overflow rod mill are described, and significant operating variables are reviewed in terms of their effects on mill power draw, power efficiency, and practical aspects of circuit operation. Key factors for improving the economic performance of rod milling circuits are identified. IntroductionThis paper summarizes the findings of a detailed review of available technical information on the operation of rod mills. One of the basic problems in historical comminution testwork has been the lack of a standard measure of circuit performance. The Bond Operating Work Index, not introduced until after 1950, has proven of immeasurable value in this regard, but first has to be carefully considered in terms of its utility and limitations. Its prescribed use is described in a later section of this paper.During this review, it became apparent that rod mill performance is generally not well understood. Because of combined interactions, the effects of different operating variables may be difficult to assess, and even at times appear erratic. It is obviously difficult to rationalize plant testwork or circuit adjustments when the results are highly unpredictable. The purposes of this review, therefore, were:a) to establish what basic facts have been learned about rod mill performance;b) to define some genera l guidelines for efficient rod mill design and operation; and,c) to establish a basis for specific recommendations for plant tests or adjustments with minimum risk, and maximum potential for circuit performance improvement."

Jan 1, 1986

By Derek E. McBride

"Exploration work in the Beardmore - Tashota area has led to a reinterpretation of relationships between gold mineralization and the geologicalevolution ofthe area. The host volcanic rocks form two parallel volcanic belts connected by a much smaller cross-cutting band, which trends northeast from Beardmore to Tashota. This connecting band consists of mafic and felsic volcanic, plus clastic sedimentary rocks in a sequence conformable with the contact of the Onaman Lake Batholith to the east. A metamorphic aureole or incorporated xenoliths are lacking along this major contact and the only intrusive relationship observed is chilling between mafic dikes and a cold host granite in proximity to it. Granite dikes are totally lacking in the volcanic succession, or the overlying sedimentary sequence. A major part of this sequence consists of a polymict basal conglomerate with granite boulders and volcanic clasts in a fine-grained chloritic matrix. The nearest source for these boulders is the Onaman Lake batholith.Gold mineralization in significant economic quantities (+ 50 000 ounces) occurs at the top or above the mafic volcanic succession as quartz bands. In the Northern Empire Mine, the band is conformable, folded, boudinaged and the mineral zoning shows a relationship to variations in the host rock, not structural overprinting. In general, where the host mafic tuff is medium-grained, the quartz band is thicker, up to a metre wide, and carries economic grade; where the tuff is finer-grained and bedded, the band is very thin and low grade.Stratigraphic control and metal zoning shows that the mineralization formed as part of the development of the volcano- sedimentary succession. The other major deposits in the area (Leitch and Sturgeon River) have a similar structural history suggesting that they are also syngenetic in terms of the stratigraphic development. Regionally, these deposits were emplaced prior to any significant tectonic deformation but at the end of the mafic volcanic event.The mafic activity was related 10 a period ofextension which caused the volcanic troughs to develop along centres of rifting. The hiatus at the end of this event permitted extensive hydrothermal systems to form and deposit siliceous exhalite bands within sedimentary or terminal mafic volcanic environments in promixity to major thermal sources. Subsequently, the Kenoran Orogeny deformed the entire succession into upright folds with a sub-vertical schistosity. Evidence shows that the deposits have remained intact since deposition."

Jan 1, 1987

By W. G. Q. Johnston, J. S. Fox

"A semi-continuous belt of Aphebian magnesian extrusive and related sub volcanic rocks has been delineated by the authors over a distance of 150 kilometres in the central La Ronge lithostructural domain in Saskatchewan. They range in composition from peridotite to basalt and attain true thicknesses of up to 800 metres. For the most part, they are confined to a basal position in the La Ronge/Wasekwan metavolcanic sequence, and appear to have been extruded onto sialic crust. However, at Lynn Lake, Manitoba, in the eastern continuation of the domain, similar rocks seem to be found only at a relatively high stratigraphic level.Although metamorphism seems to have obliterated any quench textures that may have existed in these rocks, ultramafic pyroclastics, pillows and amygdules as well as intercalated, fine-grained clastic sediment attest to the volcanic nature of these rocks. Bulk chemical analyses indicate that these rocks are heterogeneous, with komatiites, tholeiitic picrites and even rocks with some of the characteristics of boninite all being present. The close temporal and spatial relationship of ""boninites"" and komatiites in the belt may suggest a high degree of Aphebian mantle inhomogeneity in the domain.Nickel-copper mineralization has been found in differentiated tholeiitic stocks within the La Range domain (e.g., at Lynn Lake), but none has yet been found in the ultramafic volcanics. However, the tholeiitic picrites do host one economic gold deposit - the Agassiz Mine at Lynn Lake .Because of the depleted nature of their mantle source, the ""boninites"" of the domain are not considered to be likely hosts for mantle-derived nickel sulphide mineralization. However, the opposite is true of the komatiites, and this points to the need for whole-rock geochemistry in setting priorities for nickel exploration in the belt. In contrast, all of the magnesian rocks of the domain probably have the same gold potential. Inasmuch as the geophysical response to gold mineralization in the domain is likely to be unpredictable, lake-sediment geochemistry, followed by base-of-till and/or alteration oriented lithogeochemistry, should be emphasized during gold exploration."

Jan 1, 1981

By R. A. Horn, S. M. Telfer

"Canada has a per capita GDP second only to Japan among the G7 countries and a positive trade balance which ranks third among the world&apos;s major economies. International trade represents a very large part of the national economy and as a proportion of GDP is larger than that of all the other G7 countries with the exception of Germany. On the negative side the Canadian current account deficit relative to the size of the economy is significantly worse than that of all major industrial countries, due mainly to the cost of servicing an immense foreign debt and to a large and worsening negative trade balance in manufacturing.The outflow of money may be reduced by increasing the productivity and competitiveness of those sectors of the economy in which Canada already has a leading competitive position and which have the potential for further growth. The mining industry is uniquely qualified in this respect in that Canada is the western world&apos;s largest producer of metals and mineral products and has the geology and the exploration skill to replenish reserves assuming that an adequate level of investment is maintained. In 1989 the minerals industry contributed $8 billion to the country&apos;s balance of payments and with the exception of forestry is the only sector of the economy which has shown consistently increasing foreign earnings over the long term.In recent years there has been a decline in exploration in Canada and a significant increase in countries such as Chile. The demand for hard currency to finance the development of the newly emerging capitalist economies of the CIS and Eastern Europe is also driving these countries to seek foreign investment to allow them to exploit their natural wealth more efficiently. Canada is therefore facing growing international competition for risk capital and in the future its trade surplus will probably decline in the face of lower cost foreign production.Canada rightly exercises a high level of environmental control on its mining operations; however a significant deterrent to investment is the fundamentally unjust application of the many provincial and federal environmental laws, under which a mining company, even if it takes every measure to protect the environment, runs the risk of eternal and unlimited future liability. If this situation is not rectified the effect will be an increase in global pollution as mines in countries with more lax application of law and regulations controlling environmental damage replace those of Canada. Tax benefits and incentives are a more efficient means than arbitrary regulations in minimizing environmental damage."

Jan 1, 1994

By James F. Kelly

"Research and development on the production of liquid fuels from coal is rapidly expanding worldwide. AImost every industrialized country is engaged in coal liquefaction research and process development. In Canada, the federal government, through CANMET, is actively supporting coal liquefaction research and development in a number of areas.A review of the basic principles and some of the processes in the production of liquid fuels from coal is presented with reference to the characteristics of the Canadian coal resource base. An overview of the CANMET coal liquefaction contract program is presented and specific results from the batch autoclave studies carried out with Saskatchewan lignite and Nova Scotia high-volatile bituminous coals are discussed. The development of a laboratory-scale continuous-flow coal liquefaction unit at the Energy Research Laboratories of CANMET to investigate the co-processing of coal and bitumen/heavy oil is also described.IntroductionThe CANMET coal liquefaction program is made up of two interrelated parts. The first part consists of the research and development work being carried out at the Energy Research Laboratories near Ottawa, Ontario. The second focuses on contracted research and development as part of the Coal Conversion Program of Energy, Mines and Resources Canada. The long-term objective of the liquefaction program is to contribute to Canadian liquid fuels production through the definition, research, development and demonstration of different coal liquefaction technologies for the Canadian marketplace.In coal liquefaction, the main objective is to produce liquid hydrocarbons with a higher hydrogen-to-carbon (HIC) ratio than the coal feedstock while reducing heteroatom (S,O,N) content, removing mineral matter and minimizing gas production. Typical atomic HIC ratios for a variety of Canadian fossil fuels are shown in Figure I. Canadian coals have about 500/0 of the HIC ratio present in tar sand bitumens and heavy oils and only about 20% of the ratio available in methane. In general, the cost of synthetic fuels production is related to the cost of hydrogen and, therefore, to the increase of HIC ratio between feedstock and products. On this basis, the production of liquid fuels from coal would be expected to be more costly than liquid fuels produced from bitumens and heavy oils. However, for mined tar sands and some heavy oils this difference tends to be offset by the large sand content (>90 mass %) of tar sand bitumens and the increased production costs of viscous heavy oils. For example, it can easily be shown that for equal weights of distillate <525°C) yield, current coal liquefaction processes required between two and three times less mined coal by weight than the mined tar sand s required for the most technically advanced processes proposed for bitumen upgrading."

Jan 1, 1981