Search Documents

By S. Espley, G. Tan

"Inco's Little Stobie Mine is a low-grade nickel operation producing approximately 4()()() tons per day. Backfill has never been an economical option at the mine; therefore, the only viable type of mining in the upper zones has been by sub-level cave. This mining method allows for the draw-down of a rock cover into the empty stopes to provide stability to the over-all rock mass. In the lower areas of the mine, bulk blasthole mining methods have taken place, without rock fill, resulting in extremely large open stopes. As the mine reaches its final stage of recovery, it is inevitable that the hangingwall of the large voids will undergo tensile failure via spoiling.This paper deals with the collaborating efforts of Inco's Rock Mechanics group and the Little Stobie mining operations toward the successful recovery of the ore zone remnants such that the inevitable failure, and time of failure, of the rock mass is ""controlled"". Within the mining scheme, several key requirements had to be met to satisfy the operations: (1) production rates; (2) good blast fragmentation; and (3) secure pulling-horizons. A full-scale rock mechanics study was carried out involving: numerical modelling studies; pulling ellipse analyses; blast design, monitoring and analyses; laser profiling; and time domain rej7ectometry (TDR) instrumentation. The final recovery scheme, employing a controlled failure, involves recommendations on: (1) blasting techniques; (2) support systems; (3) mining sequences and scenarios; and (4) monitoring systems."

Jan 1, 1994

By Dan Currie, Tom Lamb, J. Coady Marsh, Gary Landry

"This paper describes the Cape Breton Development Corporation's experience with the Lovat M-300 tunnel-boring machine at the Donkin-Morien Mine. Between January 3 and December 21, 1984, the 7.6 m (25 It) diameter TBM advanced 3350 m (10 990 ft) . The authors will describe experiences with the machine and highlight the implications of tunnelling machines to underground coal mine development in Canada. IntroductionThe Cape Breton Development Corporation (CBDC) has recently completed the drivage of a 7.6 m (25 ft) diameter tunnel, 3.5 km (2.2 miles) in length , to access the Harbour Coal Seam at the Donkin-Morien Project. The tunnel was successfully driven with the first Canadian rock tunnel-boring machine (RTBM or TBM), designed and built by Lovat Tunnel Equipment, Inc. The initial mine development consists of the drivage of two tunnels to the first major coal seam. Future plans are proposed for the development of a 4 million tonne-per-year mine (Marsh et al., 1983, Gillman, 1982), which will require the drivage of a further two tunnels and could access up to four coal seams. The tunnel cross-sectional areas were designed to provide sufficient ventilation area and access for a production of 4 million tonnes per year."

Jan 1, 1986

By Bryon Cerklefskie, Michael Schulte

"This case study explores the usage of polymer ducting as a replacement to curtains and FRP for face ventilation in two coal mines. There are two mines looked at, one is the highest elevation underground coal mine in North America, the other is the gassiest mine in North America. The paper details the trials of both mines switching from FRP and curtain respectively to polymer ducting. The results discuss the ability for the mines to not only achieve consistent airflows and keep them in compliance but the unexpected positives. Mine A was allowed to do longer cross cuts due to increased air volume at the face. This drastically cut their costs of mining down due solely to modification of the ventilation cycle. Mine B saw economic benefits due to longer cuts between place changes. Both mines have documented lower dust, methane, noise, and improved wear and tear on their equipment as a result.INTRODUCTIONThe emergence of longwall mining in underground coal operations has resulted in new ventilation challenges. Numerous production crews strive to complete their development sections with enough time to adequately prepare for the upcoming longwall panel. Continuous miners will cut out two or three entry development sections per their ventilation plan, that is approved and controlled by MSHA (Mine Safety and Health Administration), which will drive amount of footage that can be mined at a time prior to installing roof support. At this moment the continuous miner, hereafter referred to as the CM, will back out of the entry and moves to the second entry to complete a similar cut. Typically, a roof bolter crew will pull in to the finished cut section and install ground support. This is called a place change style of production coal mining. There is an alternate method that includes a miner/bolter combination as well but that was not featured at either test site in this case study. Ventilation has to be provided to sweep the working face of each entry to control dust and gasses. Each task will have an MSHA prescribed ventilation requirement dependent on the dust levels and methane emissions of the rock for that particular mine. The CM, roof bolting and unused headings will each require constant ventilation but at different volumes. Since each working face is changing throughout the mining cycle the ventilation requirement in a working heading is never static and is changing with the working task.Traditional Ventilation ControlsTraditionally face ventilation for coal mining operations has been completed thru the usage of a curtain system and\or using auxiliary fans and ventilation tubing. Room and pillar mining systems typically utilize curtain systems, which use curtain walls that are installed by the miners by erecting wood framing and covering it with brattice curtain. This splits the drift width to allow fresh air to sweep the face and take the contaminated air and dust behind the curtain to the ventilation exhaust\return area of the mine. This method is difficult to adjust the airflow from entry to entry during changing cycles and requires that a wider drift is mined out in order to have enough room for the brattice wall. In operations that require roof bolting, this method limits the length of the cuts from the CM prior to advancing and can lead to not providing enough ventilation to keep dust and methane levels below compliance requirements."

Jan 1, 2019

By Allan A. Este, Bruce Arthur

"Rio Algom's Stanleigh Mine and Mill Operation Was' officially started up in August 1983. In September 1982, Rio Algom contracted Estonix International Inc. from Lively, Ontario, to develop and implement two innovative programs: (1) Work Renovation Planning, and (2) Systems Performance Training. This paper deals with the development and implementation of these two concepts relative to the plants technology from start-up to present and the exceptional results achieved. This paper discusses how a small but motivated workforce resulted in the smooth transition from startup to full production. It also deals with how these concepts were applied elsewhere in the organization which permitted a successful transition and downsizing of the over-all operation.IntroductionRio Algom Limited produces uranium in Elliot Lake, Ontario. In the late 1970s Rio Algom entered a contract with Ontario Hydro to supply uranium from its Stanleigh property, which had been idle since 1960. The mine was subsequently upgraded, and a new modem mill was designed and built, commencing operation in 1983.From then until September 1990,Rio Algom had three producing mines and mills in the Elliot Lake area. Quirke mill, with a capacity of 6350 tonnes per day, operated continuously from 1968. The Panel mill with a 3000 tonnes per day capacity, operated since 1979. Stanleigh mill continues to operate under long-term contracts, although at a production rate about 25070 lower than its rated capacity of 5000 tonnes per day.Both the Quirke and Panel mills, although not entirely similar, were conventional uranium mills utilizing crushing, grinding, leaching and ion exchange. As such, and in keeping with the traditional management style, there was a rather large mill operating workforce, which utilized a line-of-progression job classification system."

Jan 1, 1993

By Ellie Condolios

Hydraulic hoisting offers a number ~f attractive features over conventional hoisting methods: small shaft space requirements; great flexibility of layout, including pick-up or delivery of the material at points distant from the mine shaft; low investment and operating costs. However, limited practical experience with this type of hoisting dictates that careful design and, frequently, extensive testing be done by competent engineers before large-scale installations are built. This paper covers the following: basic laws and design criteria for hydraulic hoisting installations; a description of a coal hoisting installation which has been in industrial operation since 1960, with a vertical lift of 600 feet and an annual capacity of 500,000 tons of -3 ~-in. coal; and a tentative appraisal of the process, including cost estimates. THE transportation of solids in water flowing through a pipe-line has, for a number of years, been common practice in dredging, public

Jan 1, 1963

By J. G. Thomson

Development of the Canadian North, a subject of growing national interest, must in part await the development of better forms of trans-port. The estimated 500,000 square miles of muskeg terrain in the north combined with the" scarcity of roads make essential the early development of special purpose muskeg vehicles. Good progress has been made in the last eleven years in classifying muskeg and some progress has been made in determining its mechanical properties. Limited travel is now possible through the use of special purpose tracked vehicles which have been built without adequate design data. A program to provide data which can be used to optimize muskeg vehicle designs began in 1957. The results of the second phase of this pro-gram are presented in this report. It is shown that vehicle performance in muskeg is directly related to the mechanical properties of the muskeg. Further, it is shown that good de-sign practice for tracked vehicles expected to operate in snow, sand, soft clays and loams is also good practice for muskeg vehicles. All indications are that muskeg mechanics is properly a part of conventional soil mechanics.

Jan 1, 1961

By R. Roufail

Mineral exploration is in a race to employ drilling technology that can perform the exploration and drilling investigation in a fast and inexpensive manner. After an extensive study of the available drilling technologies in the market, coiled tubing was chosen as a tool to be employed for mineral exploration due to its flexible mobility and ease of operation with a minimum number of personnel. Since coiled tubing technology is primarily used in the oil and gas industry, it was important to re-design the coiled tube rig to drill hard rocks in a fast and feasible manner. The main requirements were to drill the smallest feasible hole diameter and go as deep in the ground as possible, in the shortest reasonable time. The drilled rock particles, cuttings, are to be collected and analysed at the surface for their metal mineral contents. The process also needs to be repeated multiple times at different locations for mapping, without the need to change the tube on the rig due to failure or potential failure. The focus of the new designed coiled tube, for drilling and mineral exploration, is three fold. First is to increase the rate of penetration in drilling by designing a small high speed turbo motor. Second is to determine the controlling parameters of cuttings transport to effectively lift the cuttings to the surface for analysis and third is to minimize the overall weight of the rig for manoeuvring and prolong the life span of the coiled tube string. In this paper, a small downhole turbo motor, 5cm outer diameter, is designed to achieve a rotation speed of up to 10,000 rpm to fit on a small bit, coiled tube drilling assembly. The motor design utilised multiple finite volume and finite element analysis softwares for fluid flow study and fluid structural interaction analysis. The paper is also introducing the concept of a flow slurry loop that is designed to lift the cutting particles to the surface for mineralisation analysis. The controlling parameters of the cuttings transportation are the particle?s physical properties such as size, density, concentration and shape, as well as the rheological properties of the carrying fluid, drilled hole angle, as well as the fluid flow rate and flow dynamics within the annulus gap between the coiled tube and drilled hole. Such parameters are addressed via experimental work as well as numerical analysis. The paper is also presenting the selection and testing procedure of the material type for the coiled tube string. The tube needs to be light in weight for overall rig weight and its transportability. The tube is also required to drill several dozens of investigation holes before failing due to fatigue. A fatigue bending machine is designed to test the endurance limit of candidate materials for coiled tube strings and a performance index methodology is followed for material selection of the optimum material. The coiled tube rig is designed to be light in weight for transportation and relocation. It is also required to speed the drilling operation with the minimum footprint and reclaim the drilled rock particles for mineral composition analysis at the surface.

Aug 1, 2013

By P. Coursol

The Noranda Reactor Process (NRP) has been in operation now for more than 30 years and this mature process has attained a high level of performance. The NRP at the Home Smelter of Xstrata Copper treats a wide range of feed materials and a thorough knowledge of both process control and smelting physico-chemistry has been beneficial to help meet the required plant flexibility. In this regard, some level of predictive knowledge related to slag chemistry, in particular, the liquid and solid phases such as spinels or olivines, has been found to be beneficial. In the last decade or so, the availability of commercial thermodynamic modeling packages, such as Factsage1m have been utilized with advantage to help the plant optimize slag chemistry and minimize problems from difficult slags, for example, those the could arise from undue feed variability. This paper illustrates the application of this software in examining a range of operating parameters such as: %Fe in product matte, the %Fe/%Si02 ratio in the slag, the levels of minor slag components including CaO, Ah03, ZnO, and MgO, and the level of oxygen enrichment on the operating conditions of the NRP. The slag composition boundaries at the conditions affecting magnetite control and solid magnetite/other precipitated solid phases, as well the conditions influencing the slag liquidus ranges of NRP slags are also discussed with respect to the overall process chemistry.

Jan 1, 2007

By Oleg G. Tovmachenko

We have studied optical properties of fluorescent nanoparticles. These particles consist of a metal (gold/silver) core, an empty and a dye labelled silica shells. The different dye molecules with moderate quantum yields (about 0.3) has been used. Almost all of types of nanoparticles show fluorescence enhancement. This enhancement is strongly dependent on the degree of the overlap between the surface plasmon band of the metal and the absorption/emission band of the dye molecules. The results are interpreted in terms of competition between local field enhancement and quenching of fluorescence by the metal surface.

Oct 1, 2003

By J. Dubinski

Poland is the ninth largest coal producer in the world and Coal Company is the largest Polish producer of this deposit yielding 51% of national production. Coal Company mines are located in the Upper Silesian Coal Basin. These are underground mines which operate in difficult geological conditions at great depths of up to 1200 m. One of the most common natural hazards in Polish mines are rockburst and seismic hazard impacting on surface infrastructure and habitants. In the assessment of the rockburst and seismic hazard methods of mining seismology play a leading role. This paper presents progress that was achieved in the last few years in the implementation of new seismic monitoring systems and seismic interpretation methods for the prevention of hazard deriving from seismicity induced by mining. This progress in assessment of rockburst hazard and impact of seismic activity on the surface infrastructure was achieved through close cooperation between the Coal Company and Central Mining Institute ? the country?s leading scientific institute in the field of mining seismology. New theoretical solutions are in the process of testing in mines of Coal Company where seismic monitoring systems are installed and controlled by well-qualified personnel. Some directions of further joint actions to increase the effectiveness of rockburst and seismic hazard assessment are presented as well.

Aug 1, 2013

By O. Hungr, V. Gischig, G. Preisig

Deep-seated landslides are characterized by slow time-dependent movements induced by constant gravitational creep, and periods of acceleration associated with stress changes within the rock and the preexisting fracture network. Natural stress changes are typically caused by seasonal variations in surface temperatures and groundwater pressures, but also by rare and more violent events such as earthquakes. These processes are responsible for cyclic loading and unloading that leads to rock mass damage, fatigue and progressive failure with time, and may explain sudden, unexpected rock slope acceleration phases. In this work, we present a set of distinct-element models to investigate and compare the role of hydromechanical fatigue and seismic fatigue in the history of a deep-seated landslide. Hydromechanical fatigue arises from the fluctuation of pore pressure in fractures accompanying periods of significant groundwater recharge. In alpine areas, there are usually one or two cycles per year associated with snow melt and intense rainfall periods. In the presence of a deep confined aquifer within the rock slope, the amplitude of pressure fluctuations may reach values of 0.25-0.5 MPa. Hydromechanical models considering such pressure changes are able to reproduce observed slope accelerations-decelerations phases. Substantial accelerations may occur even in the absence of a cycle of exceptional amplitude, depending on the current state of fatigue. At a given time, one or more fractures may be critically-stressed, and a small change in applied stress is enough to cause local failure and induce a crisis of enhanced slope acceleration. This is augmented if the rock slope contains planes of weakness associated with its tectonic history, glacial debuttressing, etc. The corresponding behaviour is analogous to laboratory experiments on rock and metal fatigue. Similar fatigue effects have also been proposed for repeated earthquake events in seismically active regions. Unlike hydromechanical stress changes that occur in a more localized portion of the rock slope, those induced by passing seismic waves involve the entire rock mass. Moreover, the frequency and amplitude of stress perturbations due to earthquakes are different than those induced by pore pressure variations, although both likely contribute in combination to the degradation and progressive failure of large deep-seated landslides when both are present. The results presented illustrate that: (1) assessment of slope stability near critical infrastructure (e.g., hydroelectric reservoirs) should not only consider static stability, but also failure mechanisms related to fatigue that evolve over time and may result in an apparently stable slope progressing towards a critical state due to relatively small but repetitive stress changes; and that (2) characterization of fatigue processes affecting a deep-seated landslide requires multiparametric continuous monitoring at different observation points.

Jan 1, 2015

By P. Carlone, A. Astarita, F. Rubino

Cold gas dynamic spray is an innovative technology allowing the deposition of thin metallic layers on a bulk or sheet substrate. Titanium on aluminum deposition is very attractive to the aeronautic industry, due to the enhanced corrosion resistance and wear properties of titanium coating as well as its improved compatibility with CFRP, preserving the reduced cost of aluminum substrate. One main drawback, however, is related to the micro-porosity of the deposed layer, negatively affecting the corrosion barrier performance. In this paper, the effect of selective laser post-treatment on pure grade 2 titanium coatings on AA2020-T3 sheets was experimentally and numerically investigated. Morphological features, microstructure and chemical composition of the treated zone were assessed by means of optical microscopy, scanning electron microscopy and energy dispersive X-ray spectrometry. Microhardness measurements were also carried out to evaluate the mechanical properties of the treated coating. A numerical model of the laser treatment, based on a finite volume scheme, was implemented and solved to simulate the process and discuss the experimental outcomes. Obtained results highlighted the key role played by heat input and dimensional features on the effectiveness of the treatment.

Jan 1, 2015

By G. H. Blackwell, N. I. Norrish

"At most operating mines, geostatistical are reserve estimation methods have been implemented by head office or consulting groups . With recent advances in small computer technology it is now possible for a remotely-located mine department to independently implement a geostatistical package.This paper describes the evolution of geostatistical routines to calculate the mineral inventory for porphyry type copper/ molybdenum or similar are bodies. The problems encountered in down sizing the geostatistical routines to run using limited minesite computing facilities are discussed. The high quality of the results, in spite of some compromises to geostatistical theory, is emphasized.The first stage entailed the development of a mineral inventory based on diamond drill data. The difficulties in fitting variogram models to two metals, copper and molybdenum, and the shortcomings of the mineral inventory due to the mixing of lesser quality exploration data with data from more recent diamond drilling are discussed.To improve the ore reserve estimates for short-term planning, a mineral inventory was produced using both the diamond drill and production blast hole drilling data. This inventory, when compared to actual grades, was found to be quite satisfactory for short-term planning. The inventory also provided a reliable data base for long range pit design and financial planning. By regularly updating the mineral inventory, many of the uncertainties of mining a low-grade orebody were minimizedIntroductionThe comparatively low grades of many Canadian mineral deposit s, the escalation of mine operating costs, and the volatility of metal prices in recent years, has required improvements to both short- and long-term mine planning.One of the prerequisites to improved planning systems is the need for accurate grade prediction. This paper describes the on-site implementation of geostatistical techniques for grade estimation of a porphyry I vein type copper/molybdenum ore body ."

Jan 1, 1987

By M. Zanini, D. Wong

ABSTRACT: Metals market improvements in 2005 drove the desire to increase nickel throughput and the production of nickel oxide sinter at the Vale Ltd. Copper Cliff smelter. Significant difficulties were encountered due to the unreliable quality of Bessemer matte being produced. Concentrate feed changes and the loss of technical and operational expertise during the previous market downturn contributed to the challenge of making the required improvements. Significant progress has been made in the converter aisle by focusing on employee engagement and standardizing best operating practices for a new generation of skimmers. This paper documents these initiatives and seeks to balance the art and science of converting.

Jan 1, 2012

"The successful commissioning and ramp up of the Albion Process™ at the GPM Gold Project relied on the successful scaling up of the process from batch and continuous pilot plant campaigns (Voigt et al., 2015). Critical information about reaction kinetics and residence time, grind size and pulp density were determined at the laboratory scale and successfully applied to the commercial scale. A limitation of small scale testwork, is that some parameters cannot be measured reliably and scaling up is a function of the physical size of the equipment which isn’t possible to test with laboratory scale equipment. Oxygen mass transfer rate is one such parameter since this is a complex interaction of many factors including slurry temperature, solution and slurry chemistry, slurry viscosity, agitator type, dimensions and power, oxygen bubble residence time, oxygen purity, tank geometry and oxygen injection technique. Oxygen generation represents an important operating cost for the Albion Process™. Pivotal to the Albion Process™ operating economically at atmospheric pressure is the capability to efficiently transfer oxygen while utilising as much oxygen injected to the process as possible. To respond to this Glencore Technology developed the HyperSpargeTM supersonic gas injector. This paper compares the HyperSparge™ against other sparging techniques to quantify the benefits of oxygen injection via a supersonic gas jet on scale up of the oxygen mass transfer system. The paper then examines plant survey data from the GPM Gold Project to demonstrate the very high oxygen utilisation that can be achieved with a correctly designed oxygen mass transfer system.INTRODUCTION One of the main challenges in chemical reactor design is the scale-up of processes from the laboratory to industrial scale. Processes which cannot be faithfully simulated with an experiment at the laboratory scale face challenges due to the physical dimensions and complexity of full scale operation. One example of this is the design of oxygen mass transfer systems in atmospheric oxidative leaching circuits such as the Albion Process™. A number of constraints associated with the use of laboratory scale equipment to design full scale circuits are involved in gas mass transfer processes in agitated slurries such as the Albion Process. Chiefly, typical laboratory and pilot size equipment lacks the required volume to provide useful design data without relying on empirical correlations: the specific agitator power input is artificially high, the bubble residence time in the vessel is artificially low, the oxygen partial pressure at the base of the vessel is artificially low and the oxygen delivery method may differ significantly to the industrial process. Further, the dynamic nature of the process introduces additional impacts on gas mass transfer, including the presence of solids, recycle streams and minor elements, plus the variances within the reality of a process plant such as disruptions or variance of feed quality."

Jan 1, 2017

By Yasuo Iizuka

We have had studied CO oxidation on unsupported Au powder (mean particle size, ca.100nm) manufactured by evaporating ultra high purity gold metal (>99.99%) in inert gas and reported that it showed some activity after oxidizing pretreatment in O2 at 423 K?453 K. However, recent XPS analysis of the Au powder revealed that it contains much amount of impurity metals such as Ag and In at levels which far exceed those expected from the impurity level of raw gold metal in the bulk. Several samples of Au powder containing different amount of impurity metals were prepared to examine whether the activity depends upon the existence of surface impurity or not. Activity measurements were performed at 273 K after undergoing the powder under various pretreatment conditions. Although the activity of Au powder varied to some extent according to the pretreatment condition, it is strongly correlated to the surface concentration of Ag. Such dependence was not found for In, indicating that the activity of unsupported Au powder is mainly due to the existence of Ag in the surface layer. The activity attributable to ?particle size effect? was not recognized for Au powder with a mean particle size larger than 80 nm.

Oct 1, 2003

By T. Senga, T. Namihira, S. Terada, S. Owada

"Electrical disintegration (ED) has been well known as a good comminution method to improve liberation of compositional phases because it was reported that electron avalanche could occur preferentially at phase boundary. But the detailed mechanism of the ED has been still not known. This paper describes the results of ED experiments using synthetic binary sample, copper/resin, under the conditions of various distance between electrodes, and discusses the energy distribution in the three kinds of phenomena in the ED process, which are(1) streamer progression in water, (2) electron avalanche in water, and (3) electron avalanche in solid sample, by measuring current and voltage with elapsed time. Then, it has been found that the energy distribution in the phenomenon (1) is quite low and that the distribution in the phenomenon(2) had a considerably large compared with that in the(3), which indicates that the shockwave generated in water could contribute much to the sample breakage.INTRODUCTIONElectrical disintegration (ED) has been well known as a specific comminution technology which enhanced selective breakage at phase boundary and lead to a good liberation among compositional phases1-6),but the detailed mechanism has not been clarified yet. This study describes energy distribution among the phenomena in the ED process by using a synthetic binary sample, copper/resin, the phenomena of which are (1) streamer progression in water, (2) electron avalanche and shockwave generation in water and (3) electron avalanche in solid sample usually at phase boundary. The energy distribution could be calculated from ED experiments and from voltage-current changes between electrodes as a function of elapsed time.SAMPLE AND EXPERIMENTALSampleThe sample used in this paper was a synthetic binary solid of copper/resin as shown in Figure1.Cut and polished pure copper lump was put into silicone mold and melted epoxy resin was poured into it and cooled, then, finally the binary sample was polished and molded in the form of 10 mm * 10 mm * 10 mm."

Jan 1, 2017

By Constantin Pitis, Paul Slatter, Behnam Pirouz, Laura Contasti, Markus Zeller, Sadegh Javadi

"The centrifugal slurry pumps feeding cyclones are critical components used in the grinding process. It is well known that for this type of pumps the performance degradation is very intense. To minimize downtime a complete stand-by slurry pump is always installed in a parallel circuit. The replacement decision of slurry pumps is sometimes set on specific periods of time that are empirically determined, based on previous experience; unless a pump failure triggers the second (standby) pump. Given the significant energy costs in the grinding process and a desire to increase competitiveness, engineers and scientists started research in this field while manufacturers also took actions in order to improve pumps reliability and performance. The lack of standardization regarding the methods used to benchmark and evaluate the energy performances of cyclone slurry pump systems in the mining industry makes it difficult for an enterprise to take informed decisions concerning the replacement or optimization of its process based on energy benchmarking of such slurry pump systems. This paper proposes a new methodology of benchmarking slurry pump performances using a new concept of Benchmark Energy factor (BEF) based on Mathematical Model Benchmarking. The concept of BEF has been proven successful in other industries. A new standard addressing the guidelines for benchmarking the energy performance of slurry pumps for cyclones was proposed within the Canadian Standards Association. This standard will provide a unified and consistent methodology for performing measurement activities with the ability to measure and verify the system energy performance in the field through the BEF approach. Practical examples based on the new concept are presented with comments."

Jan 1, 2017

By T. Narita

The diffusion barrier coating system (DBC system) was designed to suppress interdiffusion between alloy substrate and coatings in addition to ensuring slow oxide growth at high temperatures. In this report the concept of the DBC system will be introduced, and the results obtained for various heat-resistant alloys are presented. In this DBC system the s-phase of the Re-Cr-Ni system was selected as the barrier and is formed by electroplating Re-Ni and Ni films from aqueous solutions, followed by Cr and/or Al pack cementations. A typical DBC system consists of Ni-base superalloy / triple s-Re based alloy layer / ?’-Ni3Al and/or ß-NiAl (with or without Pt addition) / a-Al2O3. It was found that the DBC system maintained its structure for long time exposures because the s phase has tie-lines with the ? and ?’ alloy substrate and the ?’ and/or ß coating. The s-Re based alloy can suppress both the inward Al diffusion and the outward diffusion of alloying elements. The DBC system was successfully applied to various heat-resistant alloys such as Ni-Mo and Fe-Cr-Al based alloys, and these alloys with the DBC system were creep-deformed slowly under external applied stresses. A simultaneous diffusion coating process for Al and Hf was developed using Hf+NH4Cl+Al2O3 pack cementation. To obtain reliable and long-life coatings the combination of alloy substrate, coating, and external scale should be considered as a total system, to optimize oxidation resistance, structural stability, and mechanical properties.

Jan 1, 2010

By Troy Boisjoli, Sean Hillacre, Matt Batty

Discovered in 2014, the Arrow Uranium Deposit has undergone rapid development through successive drilling programs informed by geostatistical drill hole spacing studies. An independent third-party geostatistical drill hole spacing study was completed by Clayton V. Deutsch Consultants Inc. in 2017, evaluating the uncertainty of thickness, grade, density, and areal limit of the Arrow Deposit to determine a drill hole spacing suitable for Indicated Mineral Resources. Indicated spacing was defined to be 24 to 32 metres (“m”) to be within 15% of predicted for a nominal quarterly production volume with a probabilistic tolerance between 75 and 90%. The study not only defined the Indicated Mineral Resource resultant from the 2016 drill program, but also provided drill hole targeting criteria for subsequent drill programs aiming to convert Inferred to Indicated Mineral Resources. A subsequent geostatistical drill hole spacing study on the Arrow Deposit was completed by Clayton V. Deutsch with Resource Modeling Solutions in December 2018 to define Measured Mineral Resource spacing in support of the 2019 drill campaign. The study resulted in a drill hole spacing of 9 to 17 m to be within 15% of predicted for monthly and quarterly production volumes using an accepted industry probabilistic tolerance of 90%.

Jan 1, 2020