Search Documents

By P. R. G. Brandão, E. E. Ferreira

The presence of metallic cations in solution will affect the aggregation or dispersion of the fine hematite particles, depending on the type of cation adsorption: either specific or non specific adsorption. In this work, the zeta potential measurements were carried out on a sample of pure hematite as a function of pH and metallic cations concentration (Ca2, Mg2+, Mn2+, K+, Na+ and Al3+). The objective of these studies was to clarify the effect of these metallic cations on the surface chemical properties of pure hematite. The cations K+ and Na+ adsorbed as non-specific species and caused only the reduction on the values of zeta potential (in terms of absolute value) over the entire range of pH values tested. For the Al3+ cation, in the acidic pH range it adsorbed as a specific species and increased the zeta potential values. The cations Ca2+, Mg2+ and Mn2+, adsorbed as a non specific species at pH levels less than 6.0 and caused the reduction of zeta potential due to the compression of the electrical double layer. However, for pH values greater than 6.0, these cations adsorbed as a specific species causing the zeta potential to increase and became more positive as the pH value increased (alkaline). This effect could be due to the adsorption of some hidroxy complex species of these cations, which contributed to the positive charge. The effect of metallic cations (Ca2+, Mg2+ and Al3+ concentration, at pH 4.0, 7.0 and 10, showed the following results: a) at pH 4.0, increasing the concentrations of Ca2+ and Mg2+ resulted in on a small reduction in the value of the zeta potential. At this pH, increasing the concentration of A131 cations caused the zeta potential to increase due to specific adsorption of a negatively charged Al3+ hydroxy complex b) at pH 7 and 10, increasing the concentrations of Ca2+ and Mg2+ caused the zeta potential to change its charge from negative to positive.

Jan 1, 2004

By J. Lu, M. Mohammadi, C. Pelletier, B. Wassink

Chemical reduction of selenate by chromous ions is proposed as a novel method to remove selenate from sulfate-bearing solutions Chromous ions were generated by electrochemical reduction of chromic ions using an electrochemical cell. The investigation was conducted in sulfate medium and under various concentrations of chromous ions (0.0062 to 0.05M), pH 1 to 2.2 and temperature 10 to 60°C. Selenate ions were rapidly reduced by chromous ions to hydrogen selenide. The overall reaction at a chromous/selenate molar ratio of 8 or higher can be expressed by the following reaction. At an initial chromous/selenate molar ratio below 8, the products are hydrogen selenide and elemental selenium. At a lower chromous/selenate molar ratio and pH, more elemental selenium and less hydrogen selenide are produced. The reduction kinetics is controlled by both chromous ion and hydrogen ions concentrations. The reaction rate is first order with respect to selenate, hydrogen ion and chromous ion concentrations. It was found that the selenate reduction rate with chromous is independent of the concentration of sulfate present in the solution. The general rate equation was proposed and the rate constant was calculated as k= 0.38 M-2s-1. An activation energy of 58.7 kJ/mol was obtained in the temperature range from 10 to 50°C. Nearly 100% of selenate can be reduced to H2Se from solution containing 17 ppm selenate in less than 30 minutes at pH 2.2 and 60°C. Various strategies have been tested to remove the produced H2Se from solution. INTRODUCTION Selenium in nature is mostly associated with metal sulfide minerals such as copper, iron, zinc, and lead sulfides (Zingaro & Cooper, 1974). The extraction of metals from ores has the potential for selenium contamination of ground and surface water which can pose an environmental and health concern. Therefore, selenium contamination in the receiving environment is a key issue for many industries (specifically copper industry) and the treatment of wastewater contaminated with selenium is a growing challenge. The effective removal of selenium from contaminated water is very important to support sustainability in the copper industry and the other industries with selenium pollution issues.

Jan 1, 2019

By A. McLean, A. Hue, K. Le, Y. D. Yang, P. Wu

While the treatment of relatively inexpensive ferrosilicon alloys is a potential refining route in order to generate solar grade silicon, phosphorus is one of the more difficult impurities to remove by conventional processing. In this project, the use of an electromagnetic levitation technique was used to investigate the dephosphorization of ferrosilicon alloy droplets exposed for various times and temperatures to a hydrogen-argon gas mixture. It was found that approximately 40% of the phosphorus was removed from an 85%Si-15%Fe alloy after 20 minutes exposure at approximately 1673K, to a gas mixture containing 48.5% hydrogen. Further dephosphorization is expected with longer reaction times. The effect of increasing temperature was found to be insignificant, although processing at lower temperatures is not only economically advantageous, it also decreases evaporative silicon losses, thus resulting in a more efficient process.

Jan 1, 2015

By W H. Poole, E. R. W. Neale

A new style of tectonic map based on age of folding has been prepared for the Canadian Appalachian region as part of the Tectonic Map of Canada Project. This style of map pro-vides a clearer picture of the tectonic history of the region than any meth-od hitherto attempted. Precambrian blocks that were relatively unaffected by Palaeozoic de-formation are distinguished on the Great Northern Peninsula and in the Conception Bay region of Newfound-land. K/ A age determinations suggest that these blocks were intruded and metamorphosed during Grenville orogeny. Other Grenville-like rocks, on Cape Breton Island and in New Brunswick, were more actively involved in subsequent Palaeozoic orogeny. Taconic orogeny, the first phase of Palaeozoic deformation, took place in Middle and/or Late Ordovician time and was accompanied by intrusion of ultrabasic rocks. Evidence of the -

Jan 1, 1961

By T. S. Wanne

Tunnel sealing experiment (TSX) was conducted between 1997 and 2004 in the Canadian URL located in Manitoba. In the experiment, a tunnel was excavated parallel to the maximum principal stress direction, filled with sand and sealed with bulkheads at both ends. It was then pressurized and heated by injecting hot water. The rock mass response was monitored with seismic methods. The main interest in the numerical simulation was the damage formed during the heating phase. The large-scale PFC2D models replicated a central plane- strain section of the TSX chamber. The models captured the first-order phenomena observed in-situ displaying the difference in the damage in the roof and floor regions, respectively. This difference was due to the filling material confinement of about 100 kPa on the tunnel floor, which occurred in the course of the heated experiment.

May 1, 2009

By X. Cao, M. Xiao, M. Jahazi

Magnesium alloys have low hardness, wear, erosion and corrosion resistance. The repair of service-damaged aerospace components made of magnesium alloys is an attractive solution in terms of time and cost saving. The feasibility of applying laser beam technology to repair ZE41A-T5 magnesium alloy sand castings in the machined surface conditions was studied using a continuous wave 4 kW Nd:YAG laser system. The influence of process parameters such as laser power, cladding speed, wire feed rate and defocusing distance on the shape, size and area of single cladding beads is discussed using a process optimization software. Sound single clad beads with good geometric characteristics were obtained using strictly controlled laser process parameters. The overall results indicate that laser surface cladding using filler wire has the potential for repairing aerospace components made of cast magnesium alloys.

Jan 1, 2006

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By H De Beer

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Nov 1, 2011

By P. van Zyl, M. Lombaard

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By J. Holtzhausen

"An analysis of operating costs for underground mining operations in the current global economic climate considers the financial burden for a ventilation system to be in vicinity of 30–50%. These operating costs are often overlooked by management teams in the greater scale of things when looking to save money in the procurement phase. This oversight to operational costs can be as little as the effective delivery of ventilating air to the work zone. One of the biggest opportunities for substantial savings and improvements can be realized in the selection of a quality vent duct that is suitable and fit for purpose. The key component to the selection process for quality products is a solid selection criterion that is followed during the tender process. This allows the management team to filter out unsuitable suppliers and products. The case study identifies some of the key components that were considered in the procurement and selection process for lay-flat ducting products. These included the characteristics and strength of the materials. The selection criteria also considered a ducted performance comparison that offers the best aerodynamic performance with some of the following components. • Airflow at Duct Face (m³/s or cfm), Fan Pressure (Pa), Air Power (kW or hp), Assumed Fan Efficiency, Annual Running Costs, K – Factor or Lambda, Leakage Factor, Joining Method and available Duct Lengths with weights. • Critical components considered were the current Testing standards available for: o Bursting Strength AS 4878.5, Mass AS 2001.2.13, Tensile Strength AS 4878.6, Tensile Strength AS 2001.2.3.1, Tear Strength AS 2001.2.10, Tear Strength AS 4878.7 • Other key considerations were: o Warranty Claim, Damage claims, Local storage / operations, community engagement and relationships, current testing data, previous issues, after sales service with technical assistance, etc. Hidden costs associated with product failures and operational stoppages are often not quantified during the tender process. Buyer beware. INTRODUCTION The largest constraint underground mining operations currently face are their operating efficiencies and electrical costs. The overall cost of an operations ventilation system and its components requires more focus to identify what opportunities exist to maximise efficiency and effectiveness. This tender process may not always be clearly understood and it should be broken down into fewer components to achieve quantifiable results."

Jan 1, 2019

"One of the workhorses of the minerals industry is the autogenous grinding (AG) mill and its derivative the semi-autogenous (SAG) mill. These are relatively well understood, but not so Scrubbers. Scrubbers are mechanically of the same appearance/function, so what is the difference between an AG mill and a scrubber? When, or under what conditions should a scrubber be used and when should an AG mill be used? Can the processes within be mathematically modelled?In the past decades, the minerals industry has focused most of its attention on the modelling of unit processes such as cone crushers, HPGR’s, AG/SAG mills and ball mills within conventional processing circuits. Less attention has been placed on the modelling of scrubbers. This paper reviews the difference between scrubber and AG mill modelling, highlighting some of the similarities, with a view to confident comminution circuit designs.Engineering practitioners should be comfortable with these circuit designs and not shy away from considering AG mills for both small and large scale plants. AG mills can treat both harder or softer ore and scrubbers are for only softer ores. This paper differentiates scrubber and AG mill modelling in a similar way that overflow ball mills and grate discharge ball mills are analysed. Smaller scrubbers (600 kW) are suited to small scale soft ore (100-300 t/h) operations. Larger scrubbers up to 2,500 kW have the capability of very high throughput, in excess of 1,750 t/h with soft fine feed ore. AG mills are scalable up to 28 MW and are capable of treating harder ores at rates exceeding 2,000 to 4,500 t/h. Observations are that the specific energy requirements for the mill grinding duty is wide and varied. This is to a large degree the crux of the matter in sizing, as well as, differentiating, scrubbers from AG mills.INTRODUCTIONAG milling is a mature technology that has been used in minerals processing applications for more than 100 years. In the last 50 years, harder metalliferous ores have seen the introduction of steel balls to assist in the grinding/milling action. Tumbling mills used in such a configuration are called semiautogenous mills (SAG). The greater minerals industry is no newcomer to the use of fully autogenous (AG) mills. Perhaps scrubbers are. What is the difference? When should a scrubber be used versus an AG mill? How are they mathematically modelled?"

Jan 1, 2016

By J. Etcheverry, E. Seguel, R. Díaz, F. Parada, R. Parra, E. Balladares

A thermodynamic and kinetic model is proposed to explain the formation of bornite, chalcopyrite and magnetite during partial roasting of enargite-containing copper concentrates. The proposed mechanism involves solid-solid-gas and solid-gas reactions between chalcocite, pyrrhotite, gaseous sulfur and oxygen. The formation of bornite could be explained by a two-step reaction: the first one involving the formation of chalcopyrite by a reaction between Cu2S, FeS and gaseous sulfur, followed by a second step in which the newly formed chalcopyrite reacts with additional chalcocite to form bornite. Although thermodynamically the direct formation of bornite is more favorable than that of chalcopyrite, the lower diffusion kinetics of bornite formation could explain the preferential formation of chalcopyrite. If the reaction occurs with stoichiometric chalcocite and pyrrhotite in the presence of gaseous sulfur to form chalcopyrite, no bornite is formed, while for the stoichiometric reaction between chalcopyrite and chalcocite in the absence of sulfur, only bornite is formed. For the formation of magnetite and chalcopyrite the mechanism could involve the partial reaction of chalcocite and pyrrhotite in the presence of oxygen. The proposed model is thermodynamically consistent with the experimental results obtained in laboratory and pilot plant. INTRODUCTION The processing of high-arsenic copper concentrates with over 0.7 wt.-% arsenic by conventional smelting-converting normally require an additional arsenic removal step to reduce arsenic content to levels below 0.2–0.3%. One of these high-arsenic copper concentrates is the one produced by the Ministro Hales Division (DMH) of CODELCO, which has the typical chemical composition shown in Table 1. Enargite (Cu3AsS4), chalcocite (Cu2S) and pyrite (FeS2) are the main mineralogical species present in these concentrates, with over 75 wt.-%, as shown in Table 2. Partial or “neutral” roasting of these concentrates under controlled temperature and partial oxygen pressure conditions at 923–993K (650–720ºC) can remove up to 95% of the arsenic as As2S3 (As4S6), which has a high vapor pressure under these conditions, leaving a calcine with low residual arsenic. In copper concentrates, arsenic is present generally as enargite and arsenopyrite. This compounds as well as others such as pyrite and covelite, decompose readily above 770 K (500ºC), releasing, in addition to gaseous arsenic trisulfide, gaseous sulfur which by oxidizing to SO2 generates most of the heat required by the process.

Jan 1, 2019

By G. H. K. Pearse, R. P. Taylor

The Big Whopper, one of only four giant economic rare metal pegmatites worldwide, is set to become a producer of the highly valued lithium mineral petalite (LiAlSi4O10) used in glass, ceramics and the specialty glass-ceramics familiar as Corningware® and the new ceramic stovetops. The deposit has a strike length of 1.5 km, a width of up to 80 m and a resource, open in all directions, of 11.6 Mt, grading 25% petalite. It is amenable to open pit mining and Avalon Ventures Ltd. holds a patent on a flotation process that produces an exceptional quality petalite product. The project will also produce: superb quality Na-feldspar which, too, finds use in glass and ceramics; the unusual Rb- K-feldspar for high voltage porcelain insulators; tantalum, in high demand for electronics; lepidolite, an ore of rubidium; and mica and tin. A positive prefeasibility study has been completed and it remains only to undertake bulk sampling and a full feasibility study.

Jan 1, 2001

By Denis Yaychuk, Gary Billingsley

The economic eva luation of a mineral property or mining venture should include the quantification of ri k as part of the analy is. The re ults of such an analysis provide the decision-makers not only with the most likely financial outcome and the probability of achieving that or any other outcome. but al o with a ranki ng of the relative impact of all the ri sk factors. These type of resu lts offer more complete information for investment and technical deci ions than the traditional cash flow/ ensitivity analysis. In addi tion. by attempting to quantify ri sk. the personnel providing the va ri able input are forced to take a much clo e r look at the data involved, and are fo rced to work together. the reby increa ing substantially the awa reness of the impact their work and others· work has on th e outcome of the analysis.

Jan 1, 1986

By Hermann A. Derbuch

Twin Mining made a conscious decision when it changed from gold mine explorer and developer to become a diamond explorer in Canada?s Arctic. It was a decision of survival in an environment that saw junior gold companies either disappear or turn into dot com companies. Twin Mining learned fast and staked within weeks of that decision the first 50 sq. km of claims on, what became, its TORNGAT property at 59½° latitude on the east coast of the Ungava Bay in northern Quebec. This land position, 724 diamonds later (including 322 macro diamonds of gem quality, white and transparent) grew to 507 sq. km today. The 74° latitude called when Twin Mining exercised the option to acquire 3 claims owned by Helix Resources Inc. which revealed exceptional diamond potential. A gem quality 5.4 mm (0.768 carat white and transparent) diamond and the discovery of 16 pipes on 15.2 ha convinced Twin Mining?s board to sanction the deal. Both properties have outstanding features. Kimberlite Dykes and Pipes are in outcrop. The property locations have deep-sea access near existing infrastructure. Their locations are in an environment that is stable and development friendly and has a positive track record with successfully operating mines near-by.

May 1, 2001

By Gareth Barnes

Traditional approach to improvement is driven by good ideas from good people, but whilst the business case may sound good, when the project is complete, we often have not delivered on expectations.  Why not? The best way to successfully predict the outcomes of an improvement effort in a complex process is through using statistical modelling, which considers the impact of uncertainty within interacting processes.  Applying Theory of Constraints in a model helps leaders to quickly determine: Where the constraining process(es) is/are Where improvements will add the most value How much improvement should be targeted - before the next constraint takes over The confidence level of achieving a given target, which gives us a clear pathway to improvement. This paper presents an analysis of statistical modelling applications at Vale’s Manitoba Operations to achieve the 2025 targets. Using statistical modelling of the Business Structure, the team identified a series of process improvements through a Theory of Constraints Analysis. Value Stream Maps (VSMs) were used to define the required data, apply statistical modelling, and conduct training sessions enabling the Manitoba team to identify the constraining influences. Scenario testing in the Statistical models helped identify the Hierarchy of Constraints and specify the pathway to improvement. How to Improve a Business Video link https://vimeo.com/344418155

May 4, 2025

By L. Voisin, K. Itagaki

In the reductive smelting of the copper concentrate like a blast furnace operation using coke as fuel and reductant or in processing the copper concentrate which contains coal in the bulk, a sulfur-deficient matte phase often coexists with an iron base alloy in the bottom of the smelting furnace. This alloy is generally called furnace residue or speiss when considerable amount of arsenic or antimony is contained in the alloy and in the extreme case of reducing condition the alloy is saturated with carbon. As a fundamental study to know the behavior of some precious metals such as silver, gold and platinum between the sulfur-deficient matte and the furnace residue or the speiss which are in equilibrium under reducing condition, the phase relations and distribution of precious elements in the Cu-Fe-S-As and Cu-Fe-S-Sb systems saturated with carbon were determined at 1473 K by a quenching method.

Jan 1, 2007

Train on Different Equipment - * Immersive?s interchangeable cabin controls technology - ?clip on & off? * Change Simulator from one machine to another in minutes * No technical expertise required to swap * Real, functioning, controls and displays are used to aid rapid learning Immersive has produced a range of Conversion Kits to suit most equipment. Modular design - Easy to convert from one machine model to another with a Conversion Kit. Caterpillar Models Trucks - 769D, 773D, 777D Trucks - 785B, 789B, 793B Trucks - 785C, 789C, 793C, 797 Excavator/Shovel - 5130, 5230 Front end loader ? 992, 994 Dozer ? D10, D11 Komatsu Models Trucks - HD325, 785-5, 985-5 Trucks - 730E, 830E, 930E Dozers - D375A-3, D475A-3 Shovel - PC8000 P&H Shovels - 4100A, 4100XPB, 4100BOSS Hitachi Shovels - EX2500, EX5500 O&K Shovel - RH200 Bell Articulated Truck - B40C

May 1, 2003

By J .. Carignan, Y. Dembele, J .. Guha, A. Fowler, A. Gobeil

The Barlow Lake stratigraphic section comprises the top of the Gilman Formation, the Blondeau Formation and the three sills of the Cummings Complex. Representative samples were analysed to allow characterization of the chemo-stratigraphic profile and geochemical affinity of the six rock facies found in the section. All the mineralized horizons are associated with sedimentary units. Geochemical signatures associated with the mineralizations are either very weak or very localized and shown by increases in K20 around the mineralizations and Fe203 near them. The mineralizations are stratiform, synvolcanic but resedimented and remobilized by regional metamorphism and possibly by hydrothermal activity initiated by the intrusion of the Cummings Complex. The evolution of the sedimentary basin with the decrease of its depth is confirmed by the chemo-stratigraphic profiles. Stratigraphic position in the section is important in order that the chemo-stratigraphy may serve as a guide for mining exploration in the distal facies of the Blondeau Formation.

Jan 1, 1984

By Jin Li

The tensile properties and microstructure of AZ91 Mg alloy before and after equal channel angular extrusion (ECAE), and the fracture behavior during tensile testing for as-extrusion and ECAE AZ91 were investigated. The alloy was performed ECAE from one to eight passes at 498K. The elongation decreased with the pass number increasing after ECAE. Grains were refined, partial coarse ß-Mg17Al12 phase fell to pieces, fine ß-Mg17Al12 precipitated in the AZ91 Mg alloy after ECAE. During tensile test the a-Mg/ ß-Mg17Al12, a-Mg/Al8Mn5 interface and the grain boundaries in a-Mg matrix acted as the crack initiation sources. The frequency of micro-cracks at the a-Mg/ß-Mg17Al12 interfaces and grain boundaries increased after ECAE, which accelerated the growth and coalescence of the micro-cracks during tensile test and resulted in the decrease of elongation of AZ91 Mg alloy by ECAE.

Jan 1, 2006