Search Documents

By A. Pearson, F. A. Auld, S. O. Colbeck

"""The theory of buckling of shafts and Steel tunnel-linings"" was published by E. Amstutz in 1970 and commented on by S. Jacobsen in 1974. The authors have revised and enhanced Amstutz’s work to address Jacobsen's comments on its limitations and to extend its validity over a wider range of pipe/shaft geometries, including those commonly found in deep mine access shafts. The author has looked at Amstutz’s assessment of strengthening with flexible shear anchorages and adapted the theory of non-linear shear deformation response of bolts to develop a method of assessing increased buckling capacity utilising the full plastic shear capacity of studs. INTRODUCTION “Amstutz Buckling” refers to the buckling of pipe embedded in concrete under external uniform pressure. In terms of a mining environment, this relates directly to the design of a watertight shaft. This load case will commonly occur where a main shaft is cast against a geostatically stable primary liner and the only load applied to the final shaft is that of a uniform ground water load. Ernst Amstutz wrote his first paper on buckling of pressure-shaft steel linings in 1950 and subsequently improved his theory (Amstutz, 1970), which was then widely adopted for use within the industry. Years later, an alternative approach (Jacobsen, 1974) was proposed. Within his paper Jacobsen critiques Amstutz work, identifying some mathematical inconsistencies and highlighting limitations of the theory imposed by approximations adopted by Amstutz. Despite these limitations Amstutz work has still been used as the favoured design theory for use in the mining industry. In reviewing this body of work the author realised that with the advent of readily available computing software it was possible to adopt an iterative approach using Amstutz approximate formulae to find a solution to the original precise formulae, thus eliminating the limitations highlighted by Jacobsen The shear deformation to load characteristics of bolts has long been established (Crawford & Kulak 1968) and used for the plastic design of bolted connections in shear. This relationship is directly transferable to the design of shear studs, typical properties are well known, and actual values easily established in simple lab tests. The author has taken this relationship and modified Amstutz theory (Amstutz, 1970) for shear anchored strengthened liner buckling, to give a more efficient solution, using readily available material properties."

Jan 1, 2019

Iron control and iron residue management and disposal are significant issues in all zinc production processes. This paper briefly reviews the most important primary zinc production routes and discusses the challenges posed by iron control in each of them. The technologies and strategies that have proven successful in controlling and managing iron are discussed. SNC-Lavalin's experience in designing and commissioning zinc plants provides a unique perspective from which to review this aspect of zinc production.

Jan 1, 2006

By Hao Zhang

Site inspection is an important component of safety management system. In current practices, the inspectors evaluate the safety condition on a construction site with the assistance of a standardised checklist. However, the checklist emphasizes on evaluating the implementation of safety management system, but provides limited task-specific check items for assessing whether the individual construction tasks are conducted under safe condition and in a safe manner. To address this issue, the research presented in this paper aims to provide safety practitioners with comprehensive and taskspecific safety information to promote effective risk identification and facilitate strategic risk control during site inspection. Specifically, this research first builds a project-specific safety information database, which stores potential risks and control measures for each construction task. The research team then develops a mobile decision support tool to retrieve information from the database and support safer decision-making on site. The tool supports users in two ways: one is to provide daily risk checklists and risk control strategies to guide step-by-step inspection alongside the project schedule; the other is to let users input any safety-related keywords during the safety inspection process and the tool returns relevant safety information by applying text mining algorithms. It is ongoing research. This paper presents an overall research framework and discusses the progress in developing safety database and data retrieval concepts. The outcome of the project will help enhance safety management practices and reduce possible risky working conditions on a construction site.

Aug 1, 2013

By Claude Bourgoin

"The Copra massive sulphide deposit occurs as a continuous slab of ore dipping at approximately 40 degrees within a sericite schist formation. The orebody has been delineated over a distance of more than 5,000 feet down dip. This paper is mainly concerned with the mining procedure, and particular reference will be made to the use of steel mill holes and hydraulic roof supports. The gravel backfill line, which is operated both by gravity and hydraulically, is described. The paper mentions some of the operational problems, discusses the feasibility of longwall mining and presents the information obtained from stope testing."

Jan 1, 1966

By S. C. Radopoulou

Pavement condition assessment is an indispensable constituent in maintaining roadway infrastructure. Current practices for pavement condition assessment are labor intensive which introduce subjectivity in pavement rating and are time consuming. Automated methods rely on full 3D reconstruction of the pavement surface which introduces high equipment and computation costs. This paper presents a methodology for detection of patch type distresses in asphalt pavement images. This method uses filtering and histogram equalization for clearing and enhancing the image accordingly. It continues by applying the morphological process of closing, along with some rules based on the characteristics of a patch when captured in an image, to finally detect the area it occupies. Criteria for area, length, and width of a patch as seen in an image are taken into account to decide whether a probable patch is actually a patch. The method has been implemented in C#. The preliminary experiments demonstrate it produces promising recognition results

Aug 1, 2013

By G. Belzil, F. Robichaud, M. Fullam

ABSTRACT The Goldex mining and milling complex is operated by Agnico-Eagle and is located in the Abitibi greenstone region of northwestern Quebec, Canada. Commercial production started in 2008. Average gold recovery is 93.5% with approximately 68% of gold recovery coming from the gravity circuit. During the first three years of production, three gravity audits were carried out to optimize performance of the gravity circuit. This paper presents results of the audits and the development of a model linking gravity and overall gold recovery, and outlines improvements made to increase gravity performance and reduce operating costs.

Jan 1, 2013

The Nak?azdli First Nation and the municipality of Fort St. James are located in the Stuart Lake/Nak?al Bun area and are not unfamiliar to mining. These northern British Columbian communities have been associated with the historic Pinchi Lake Mercury mine and today are closely linked with British Columbia?s newest mine, the Mt. Milligan mine. Prior to the construction of Mt. Milligan, community health and social service providers were concerned about potential impacts that would occur from new mineral development activities. This concern has led to a partnership between the above communities and researchers with expertise in the area of mining and health. This paper describes: the current mining and health environment with a focus on British Columbia; mining trends in the Stuart Lake/Nak?al Bun area; the current community-based health research project funded by the Vancouver Foundation and the Canadian Institutes of Health Research, and; a suite of community-based health recommendations to mining companies on key issues to consider when developing projects near municipalities and Aboriginal communities in Canada, based upon one of the newest mines under development in Canada.

Aug 1, 2013

By M. Venkatraman

The limit of Hall - Petch relationship in ultra fine grained steels has been examined based on dislocation pile-up mechanism. When the grain size becomes small the dislocation multiplicity ceases resulting in very low work hardening rate in these materials. An approximate analysis of the theories of hardening indicates that H-P relation is obeyed up to 100nm. It appears that grain refinement is not the suggested approach to improve toughness as well as strength below a critical size.

Jan 1, 2004

By Rita Awwad

Building Information Modeling (BIM) has been gaining a significant edge in the construction industry over the last decade. BIM allows gathering all building information in one shared database that can help all construction entities better understand, integrate and visualize all work progress from inception to operation of the building. The main purpose behind BIM is to bring all project participants together (Client, Architect, Contractor, Consultant) since the initial stages of a project allowing them to cooperate and work as a team in the promise of an increased productivity, reduced cost, enhanced quality and faster delivery. However, a full-fledged implementation of BIM tools and benefits is not yet achieved in the construction industry and remains a debatable issue for researchers and practitioners in the construction field. This paper aims at assessing BIM awareness and usage in the Lebanese construction industry through conducting interviews with contractors, architects and consultants that are key players in the Lebanese market. A comprehensive literature review about BIM adoption in some developed countries and in the surrounding region is also provided in order to better evaluate the Lebanese industry status in comparison with foreign industries. This research sheds the light on BIM awareness of the different construction parties in the Lebanese market, assesses the extent of its current use, identifies the pertaining implementation challenges, and provides recommendations to enhance BIM role in the Lebanese construction industry.

Aug 1, 2013

By E. A. Morris

It has been shown that Alberta oil-sands fluid coke can be effectively used to reduce SO2 to elemental sulphur while simultaneously producing sulphur-impregnated activated carbon (SlAC). In the capture of mercury from industrial flue gases, SIAC has proven to be a highly effective adsorbent material. The current research aims at developing an existing SlAC technology to meet the needs of copper smelters for mitigating both mercury and SO2 emissions, while making elemental sulphur as a co-product. The challenge behind this undertaking is that these flue gases generally contain percent levels of 02 and H20 vapour (2-12%). The focus of this study is therefore on the feasibility of reducing SO2 using fluid coke under copper smelter flue gas conditions, as well as the optimisation of SIAC properties for capturing vapour phase mercury. It is hypothesised that mercury capacity is strongly affected by the 02 potential of the activation gas due to changes in surface sulphur types arising from different reduced sulphur species. To verify this, gas chromatography is used to analyse the reaction products while XPS and XANES will be used to describe the nature of sulphur on the SlAC surface. CVAFS analysis of mercury capacity will finalise the hypothesis assessment. Preliminary results indicate that 02 at 5% does not play a significant role in SSA or pore development. As expected, increased residence time contributes to SO2 reduction and elemental S yield.

Jan 1, 2007

By T. G. Joseph, M. Welz

ABSTRACT: Joseph (2002) introduced passive seismic monitoring to measure mining equipment performance. This paper evaluates the potential of passive seismic monitoring to correlate mining equipment operation with oil sands surface response, with a mining hauler as the seismic source. When applied to moving haulers, this action–reaction approach is complex. Vibrations from on-board equipment, such as pumps and tires, dirty the signal with noise. To facilitate any correlation, the signal must be cleaned up. Existing geophysical analytical techniques were manipulated to evaluate the noise problem and to filter sufficiently to permit an evaluation of whether a mining equipment action–ground response relationshipis in fact discernable.

Jan 1, 2011

By A. Ashrafi

The electrochemical deposition of polypyrrole coating on different pretreated aluminum-alloy 7075 substrates was carried out using cyclic voltammetry, The pretreatment of specimens consisted of mechanical polishing and/or electrochemical etching, In the latter case, an aqueous solution of phosphoric acid and ethanol was used, The electrodeposition solution was 0,25 M pyrrole and 0,1 M oxalic acid in double-distilled water, The cyclic voltammetry scan rate used was 700mv/s, Morphology of the coatings was examined using scanning electron microscope (SEM), Using the Tafel experiment, corrosion resistance of the coated substrates was investigated in 0.1 M NaC1 solutions, Results obtained revealed that electropolymerization of polypyrrole on 7075 aluminum alloy would increase the resistance against corrosion in 0,1M NaC1 solution, Also it was observed that, compared with mechanical polishing, electroetching pretreatment would be more effective.

Jan 1, 2005

By M. S. Fotheringham

Recognition of the Growing Importance of Iron and Steel Few Canadians have yet become aware that Canada's vast iron ore resources, the greater part of which is only now beginning to be developed, will inevitably have a profound effect on the entire Canadian economy, benefitting in some measure the lives of all Canadians. The great iron mining developments of Ontario, Newfoundland, Quebec, and Labrador are destined to make Canada one of the world's major producers and exporters of this material, on which our industrial civilization is?based. These developments will create new employment, new communities, new transportation facilities, and new investment opportunities. Iron ore is the foundation and the keystone of modern mechanized civilization. The most prosperous nations of the world are the highest per capita consumers of iron and steel, and in these countries the per capita consumption is increasing steadily despite the advent of light metals, plastics, and other competitive materials. Three-quarters of the human race have too little steel -and consequently too little mechanization -to provide for themselves the necessities and comforts of civilized living. Progressively they will demand, and acquire, the machines, the transportation and communication facilities now lacking, and they will win them by making greater use of the world's iron resources. It is the good fortune of this generation that Canada's 'iron age' is just getting well under way.

Jan 1, 1951

By R. R. Rogers

ABSTRACT The experiments described demonstrate that crude commercial lithium containing in the order of 0.5 per cent sodium can be refined, the resulting metal containing as low as 0.001 per cent sodium. During the process, the metal is vaporized and condensed at a gauge pressure of less than 0.04 micron. Considerable operating data and a detailed description of the experimental equipment are included. INTRODUCTION DUE TO THE unusual properties of lithium metal, its use is likely to increase considerably during the next few years (1, 2). This is of particular interest to Canadians because there are important deposits of lithium-containing minerals, especially spodumene, in Canada and it is hoped that lithium compounds and lithium metal will be produced from these deposits in the fairly near future. In order to assist in the development of this industry, the Mines Branch of the Department of Mines and Technical Surveys has initiated a programme of research in lithium metallurgy. In 1948, a paper (4) was published on methods of producing lithium metal and its alloys. Data on the corrosion resistance of some lithium alloys were included. In 1949, a paper (3) was published which showed that the addition of a small percentage of lithium to zinc anodes used for cathodic protection will improve their usefulness under certain circumstances.

Jan 1, 1951

By Douglas R. Piteau

"Assessing the stability of a slope cut in rock is basically a problem of engineering geology - geology, because it involves a sound understanding of the important aspects of geology, such as geological structure, ground water, weathering and other natural phenomena, which all relate to or exist in a geological environment, and engineering, in that quantitative evaluations and calculations are necessary, these being based on mechanics and relating to the strength of the geological materials and the forces causing instability of the slopes. The engineering geologist must make every attempt to. provide, in a quantitative way, information on those geological factors which are necessary for making calculations of the probable stability of the slope. These include numerical assessments of quantities relating to the characteristics of structural discontinuities, rock types, topography, hydrogeology, tectonic history and other environmental factors. Based on the development and extension of these general principles, both preliminary and final slope stability studies of some open pits in South Africa, Swaziland and Zambia have been conducted. Some of the basic concepts and techniques developed to carry these studies out are described."

Jan 1, 1972

By H. F. Maulson

For the benefit of those who are not familiar with the history of the western Provinces-Manitoba, Saskatchewan, and Alberta-as regards our natural resources, a few words of explanation may be in order before taking up the consideration of the Mines Act of 1930. In 1867, The British North America Act was passed by the Imperial Parliament. That Act, which is our constitution, created a union between the provinces of Nova Scotia, New Brunswick, and Upper and Lower Canada (now known as Ontario and Quebec respectively) under the name of the Dominion of Canada. Provision was made therein for embracing other parts of Canada from time to time. That portion of Canada which today comprises the Provinces of Manitoba, Saskatchewan, and Alberta and the lands to the north of them, was then known as Ruperts Land and the North West Territory. In the year 1670, King Charles II had granted by Letters Patent to Prince Rupert and his associates, known as ?The Governor & Company of Gentlemen Adventurers of England, Trading into Hudson's Bay?, commonly known as the Hudson's Bay Company, the lands and territories therein described, being roughly all the lands adjacent to and west of Hudson's bay; also the gold and silver to be found or discovered therein and other rights as more fully described in said Letters Patent. The land so granted was called 'Ruperts Land'.

Jan 1, 1930

By G. F. Vander Voort

Over the past twenty years, steelmakers have introduced improved practices for reducing the inclusion content of steels. The success of these practice changes can be monitored in a variety of ways. Chemical analysis of the bulk sulphur and oxygen contents provides a relatively simple means to assess the impact of these changes. However, microscopical test methods are still needed to assess the nature of the inclusions present. Traditional chartbased measurement methods have wide acceptability, and their data are well understood by both purchaser and producer for heat acceptance purposes. However, these methods do have inherent weaknesses which limit their usefulness for quality control, SPC, and database applications. Image analysis-based chart measurements are an improvement over manually generated chart ratings, but the data still do not lend themselves to databases and statistical comparisons. ASTM Committee E-4 on Metallography has developed a stereologicallybased image analysis standard test method, E 1245, which provides the necessary data in a form which is easily databased and analyzed statistically. This paper describes E 1245 and shows how data from different heats and melting practices can be compared statistically to ascertain valid test differences.

Jan 1, 1998

By E. Yan, M. Mankosa, E. Wasmund

"Rougher flotation in sulfide ore applications is typically performed using conventional flotation machines. The trend over the last 100 years has been for these cells to become larger in volume with cells reaching sizes of 600 m3 and in some cases even larger. The associated foundation loadings, transport and installation requirements along with building size have also increased. In an economic environment where projects must be executed with dwindling capital supply, bigger is not always better. More recently, industry is being challenged to identify new technology that allows for improved flowsheets and financial returns through efficiency gains. To meet this challenge, a novel high-intensity two-stage flotation system known as the StackCell™ was tested to potentially achieve installation volume and required retention time gains when compared to conventional flotation circuits. The results from on-site pilot scale work conducted on typical copper concentrator rougher flotation feed showed retention time gains on the order of 6 to 9 times when compared with conventional flotation equipment. This finding has the potential of reducing capital demands for rougher flotation circuit designs when incorporating the StackCell. The results from test work will be discussed in this paper showing comparative test data generated with a Denver bench batch test, pilot StackCell and large conventional cells, all receiving the same feed.INTRODUCTION Over the last few years, a number of flotation devices have been described as two-stage or multi-stage flotation units. The idea behind multi-stage flotation devices is that flotation performance can be improved by utilizing cells with multiple specialized units in series, but not all units of the same type, as is practiced in trains of multiple tank cells or columns. Instead, each unit is specially designed to provide the optimized fluid environment for each stage of the sequential flotation process. This idea has been proposed based on a study of the fundamentals of the flotation process, and the realization that the process consists of discrete sequential processes, that are each optimized with dissimilar process conditions (Finch et al, 1995), (Zhou, 1996). Instead of executing each step simultaneously in a homogeneous fluid environment, where the conditions would be a compromise between particle collection and froth recovery, the multi-stage flotation unit operates in a set of segregated process environments, each with a set of conditions optimized for that step."

Jan 1, 2018

By Lloyd W. Trevoy

Titanium and zirconium heavy minerals occur in the tailings streams from processing plants which use the hot-water extraction process for recovery of bitumen from tar sand. In a research program conducted by Syncrude Canada Limited, the crude tailings stream was upgraded to produce quality zircon and titanium mineral products. To process the tailings through conventional upgrading equipment, bitumen residues must first be removed from the mineral grains. Then, by gravity separation, fines and coarse sand grains were removed and a 71% heavy minerals concentrate was prepared which was further separated by high-tension equipment into zircon and titanium minerals concentrates. The zircon concentrate was upgraded by gravity, magnetic and high-tension cleaning to produce a high-quality 98% zircon product. The titanium minerals concentrate was separated into rutile, leucoxene and ilmenite fractions. Heavy minerals distribution in tar sand drilling core samples has been evaluated for various locations on Syncrude Lease 17, and expected annual production levels of heavy minerals have been estimated. A preliminary evaluation has been made of the potential for zircon, leucoxene and rutile production and for further upgrading of ilmenite and leucoxene to synthetic rutile for titanium dioxide pigment production.

Jan 1, 1978

By M. du Plessis, G. More O’Ferrall, A. Hartzenberg

"Lonmin Platinum has experienced several cases of large-scale hangingwall instabilities during the extraction of the Upper Group 2 Chromitite Layer (UG2) at a number of the Marikana operations along the Western Limb of the Bushveld Complex. These instabilities were all attributed to the presence and interaction of prominent geological features and highlighted that assumptions made in the design of the stable pillars and stable span were potentially overly simplistic in these areas. Investigations into the various case studies over the past ten years have resulted in the identification and classification of the rock mass characteristics of the geological structures causing the instabilities.In order to get a better understanding of these instabilities, it is important to understand the structural geology in general, and the sequence of events that led to the formation of the Bushveld Complex in particular. The tectonics involved in the formation of the various layers around the economic mineralized layers has been investigated, and the influence of these tectonic events on the stability of the UG2 stopes hypothesized.Following this investigation, the behaviour of the various layers in the hangingwall of the UG2 is better understood. This paper presents a description of the ground conditions being experienced in the underground stoping environment, the possible source of the associated structures and the resultant behavioural mechanism of these structures causing the rock mass instabilities."

Jan 1, 2015