Search Documents

By George Brien, O&apos

The history of the lighting of mine workings dates back to the early part of the 18th century, when small candles known as tallow dips, were used. These were set or held in a lump of wet clay. When looking for gas the flame of. the candle was reduced to a mere glimmer by surrounding the wick below the flame with clay. The candle was then very cautiously raised from the floor toward the roof, the observer screening the brighter portion of the flame with his hand and watching for the first appearance of the pale blue cap above the flame, even at that time, known to indicate the presence of gas. When this appeared the candle was lowered quietly and its flame extinguished before attempting to drive out the gas. A very common and dangerous practice adopted at that time was to get rid of the gas by firing it. This was done by a person selected for his nerve rather than for his caution. Dressed in a? suit of dampened sackcloth or leather, this man well termed a "fireman", would lie prone on the floor of the roadway and light the gas above him by raising his candle fastened to the end of a long stick. If he survived, which was not always the case, he would withdraw promptly to fresh air after the flame had passed over him.

Jan 1, 1924

Mineral engineering is defined as those engineering activities that relate to the discovery, development and utilization of mineral resources. Using petroleum engineering as an example, it is shown that the breadth of the field to be studied is a major educational problem. Breadth of field is aggravated by the rapidity with which technological demands may change. At present, special short courses serve to update engineering education. Recent experience suggests an increased rate of change for the future. The fact that engineers have typically human needs and goals, and the fact that engineers respond to these in our free society, introduces a third class of problems. One approach to the solution of these problems is the unified engineering curriculum based on a core of subject mat-ter common to all engineering. Experience suggests that the unified curriculum is an effective method to minimize the importance of the first two problem areas presented, and shows a degree of success in handling some problems within the third area. Perhaps, for the good of all segments of society, it is best to have both career-oriented and unified curricula represented by educational institutions of high quality.

Jan 1, 1963

By T. A. Wedge

This paper suggests a crude correction for the impact of raw material quality on factor productivity in the Canadian mining industry. Such a correction would give a figure more dependent on the changing efficiency of the use of labour and capital, and less dependent on the effects of unquantified changes in inputs.

Jan 1, 1973

By E. G. Joe

"This paper summarizes the main conclusions derived from twenty-two technical presentations made at the 1973 meeting of the Canadian Mineral Processors. Results of two surveys with response from over seventy mines were reported on Canadian milling practice for water re-use and on elimination of cyanide from mill effluents. Water and solution recycle in Canadian mills were detailed for copper, copper-zinc, lead-zinc-copper, nickel-copper, iron and gold mines. Cyanide elimination from mill effluents was reported under current practice and under requirements for further treatment by various other processes. Three recent process equipment entries into Canadian mills have been the on-stream particle analyzer, the new gravity concentration tables for recovery of fine tin and other heavy minerals, and solution-jet slurry equipment for reclaiming ground ore from storage. The principles of operation of this equipment were described along with the practical limitations that were found in their application to mineral processing. Capital costs and milling cost reductions were shown in some operations. Computer control of flotation mill processing was a major item on the program. Four major mining companies outlined their mill process control strategy, computer programs and on-stream analysis equipment. Some capital costs and personnel changes were presented, together with gains in concentrate grade and mill recovery. Recent development work has shown the effect of the type of grinding and of aeration on the recovery of sulphide minerals in flotation. One mining company reported a significant depressing effect on copper sulphide flotation while floating ore ground with mild-steel balls; also, pyrite appeared to be activated in the subsequent zinc flotation step. One company with extensive experience in the application of aeration to copper sulphide flotation showed significant improvement to copper recovery by pre-aeration. Both the effects of grinding and aeration were subject to the constraints of the chemical condition of the ore pulp. The metallurgy of silver recovery by combination grinding - gravity treatment and of gold recovery from a complex gold-sulphide ore were reviewed in two papers on precious metals. The latter paper further described the recovery of gold from the Cottrell collectors and the final disposal of arsenic from the dust collectors."

Jan 1, 1973

By T. Patching

"THE FOLLOWING notes on coal mining in the Edmonton city area are based, in the main, on scattered reports and accounts as little coal mining has been done in this area for about 20 years and few people are left who were involved in what was at one time an important industry of northern Alberta. Although coal mining is not likely to be permitted in the city area itself in the future, a record of this work is warranted to indicate the ·conditions and problems that may be encountered if underground mining again is proposed in the district in the same geological formations and in similar strata. Coal mining in the Edmonton area developed with the influx of settlers in the latter part of the nineteenth century and the first part of the present century. Probably local coal was used by the Fort's blacksmith as early as 1841, and the early settlers probably were 'gopherholing' into the outcrops along the river banks by the 1870s. The first report of commercial coal mining was in 1880 when a contract was let by the Hudson's Bay Company for the provision of 300 tons. As the population in the city and northern parts of the province grew, many new mines were opened along the river and in the district, and coal was even shipped by barge to points in Saskatchewan(1 ,2) By 1909 the Department of Public Works reported that 'Edmonton stands as the second largest domestic coal producing centre in the province'. It continued to hold this position until 1942. From about 1912 to 1951 annual production from mines in the city and surrounding district ranged between 0.38 and 0.65 million tons, depending on weather, wars and strikes. Production began to decline in 1951 because of the increasing availability and consumption of natural gas which was piped into the city and then provided to other towns and rural areas in the northern part of the province. Taylor noted that between 1880 and March 1970, when the last mine within the city area closed, the total of mines and prospects within the Edmonton city area rose to 153. Most of them were small; not more than 20 produced more than a quarter of a million tonnes during their entire life, and only three produced a million tonnes or more. As described by Taylor ""within the city district workings extend discontinuously from the apex of a narrow triangle near Groat Bridge to the base of the triangle in the Clover Bar area"". The larger mines were in this latter area. Approximate locations of the old mine workings in the city are shown in Taylor's atlas. A number of other coal mines were worked in the Rabbit Hill, Big Island, St. Albert, Namao, Cardiff and Morinville districts around the city."

Jan 1, 1985

By Hong-wei Ma

With social development and technological advancement, mine rescue robots used in complex environments have developed as a research hotspot. This paper reviews the progress of research on coal mine rescue robots, and key technologies of rescue robot design are put forward, such as mechanical structure, self-navigation and self-orientation, multi-sensor information fusion, multi-robot cooperation, and wireless communication technology.

Aug 1, 2013

By T. R. Stanley

Introduction The purpose of this paper is to interest mining men in the economic possibilities of sand deposits suitable for modern foundry work. Many members of the profession are constantly travelling over the country and it is felt that some knowledge of the necessary properties of foundry sands will enable these men t0 recognize such deposits. It is the experience of the writer that good sands suitable for the varied work of a foundry, such as that of the Consolidated Mining and Smelting Company, at Trail, are almost impossible to obtain from western Canadian sources. It is hoped that the following discussion may arouse some interest in the search for such sands. Sands are used in foundries for two purposes. The main use is for making moulds suitable for receiving hot metal. The mould must retain the? required shape until the metal has solidified. The second use of sand in the foundry is as an abrasive in sand blasting. This is a relatively minor use, and consequently will not be dealt with in detail. Any coarse sand with a high content of quartz will serve this purpose, but round-grained sands are superior to angular types, because they have not the same tendency to shatter on impact with the casting. Sand plays an extremely important part in the successful production of sound castings. This is more evident today than ever before, due to the greater variety of castings and alloys, each of which requires special sand characteristics. Poor sand is responsible for a great many foundry troubles which formerly were attributed to bad? metal; in fact, one investigator goes so far as to say that ninety per cent of bad castings can be traced directly to the sand. Very little of the vast amount of sand distributed over the earth's surface is suitable for moulding. It is the purpose of this paper to describe briefly the properties which are essential in good moulding sand. Sand for this work must be able to withstand the wash and hydrostatic pressure of molten metal, and yet be sufficiently porous to allow the gases generated in the mould to escape.

Jan 1, 1935

By W. F. Baker

Location and History God's lake is in the northeastern part of Manitoba, about 400 miles northeast of Winnipeg, or about 250 miles due north of Red lake, Ontario. The lake is quite large, having an overall length of 54 miles and a maximum width of 18 miles. There are numerous islands in the lake, the largest of these, known as Elk island, being about 15 miles long and 3 miles wide in the widest part. The accompanying map (Figure 1) shows the location of God's lake and of the mine. The God's Lake area has long been regarded as promising country for the prospector, but, due to its inaccessibility, practically no prospecting was done prior to 1927. In the years 1927-1931, inclusive, a few prospectors visited the area, but no discoveries were made. In 1932, Bob Jowsey and Archie McDonald entered the area from Island lake. They first prospected in the vicinity of Knife lake, which is immediately south of the main part of God's lake, and then moved on to the latter lake, heading for the north shore of Elk island. The first afternoon on God's Lake, when looking for a place to camp on the north shore of what is now known as Jowsey island, Jowsey discovered a quartz porphyry dyke which was cut by a number of gold-bearing bluish quartz stringers. On the strength of this discovery, he and McDonald began at once to stake the Reno group of claims. Rumours of the discovery brought in other prospectors, and other groups of claims were staked to the east, along the north shore of Elk island. A second discovery was soon made by Dan McCrea on his Gold Standard claims, three and a half miles to the east of the original discovery. Staking still continued to the east, along the north shore of Elk island, and Bob Brown and Harvey McKenzie staked the Akers group on a discovery approximately two miles east of McCrea's discovery. Through the efforts of Jowsey, the Reno, Rand, Elk, and Cona groups, belonging to the original syndicate for which Jowsey and McDonald staked, were combined with the Gold Standard, Greenstone, and Akers groups, and the Company known as God's Lake Gold Mines, Limited, was formed. Several additional groups of claims were later taken over by the Company and a considerable area of adjoining ground was staked to round-out the property.

Jan 1, 1935

By A. Bauer

This paper describes the trends in recent years in explosives formulated to produce larger blast-hole spacings and over-all lower drilling and blasting costs in hard formations. A consideration of current rotary drilling costs per ft of hole and per ton of muck versus hole diameter indicates that it is now possible that we shall see much further use of lower-energy-content, lower-cost slurries and dry mixes, and larger-diameter and, in many instances, cheaper blast holes. These will be drilled on current or slightly larger blast patterns to yield the same energy input per ton of rock and similar fragmentation at lower costs.

Jan 1, 1968

By J. F. Henderson

THE National Advisory Committee on Research in the Geological Sciences was established seven years ago - in 1949. In 1952, shortly after the Committee had really begun to function and had issued its first report, a paper ( l) was presented describing the objectives and organization of the Committee and the progress to that time. Another four years have gone by and the Committee feels a further progress report may be of interest. HISTORY Ten years ago, in 1946, the Geology Division of the Institute set up a Committee on Geological Research. This Committee, under the Chairmanship of Dr. J. E. Hawley, recommended that "a National Advisory Committ.ee on Research in the Geological Sciences be formed" (2). With the backing of the President and Council of the C.I.M. this recommendation went forward to the then Minister .of Mines and Resources and, with his approval, to the Committee on Scientific and Industrial Research of the Privy ?Council. As a result, the National Advisory Committee was set up in 1949.

Jan 1, 1956

By G. M. Behrend

"The mining and processing of mineral ores is a very old industry which is steeped in tradition. Rising demand for metals has recently forced the exploitation of lower-grade orebodies which require extensive beneficiation. The high capital expenditures involved, together with market pressures for high-quality concentrates and pellets, have forced the development of new process technologies which are heavily dependent on automatic process control. Development of suitable instrumentation has been rapid and it is being applied to mining processes today with a high degree of sophistication. The drive for higher efficiency and profitability goes on and has reached a level at which modern digital computers appear to be the only answer. However, the efficient application of a digital process computer is extremely complicated and is therefore approached by the mining industry with considerable hesitation.Some of the benefits promised by the digital computer can be obtained today by other means, which are more manageable and can provide immediate payoff. The result would be a building-block system which would utilize the digital process computer as its final component, to perform true plant optimization, free from routine chores."

Jan 1, 1971

By C. E. White

The depletion of higher grade mineral reserves will accelerate the trend toward production from progressively larger and lower grade deposits. The discovery of adequate reserves of leaner ores will require the development of improved exploration techniques with a greater depth range. The principal challenges to the Canadian mining industry are to find the mineral resources required to meet fast growing world demand and to develop mining methods and equipment to ensure production costs which will strengthen our position in export markets in the face of in-creasing world competition. The challenges cannot be met without intensive efforts to attract more technical men to the industry and to improve their training.

Jan 1, 1967

By C. Holmes, T. Holmes

Engineered-in material handling problems are responsible for significant unrealized value in mineral processing plants. At the root, is a lack of awareness and understanding of bulk material handling science and how important it is, especially in early design stages. Mineral processes add value to mined raw feedstock through physical and chemical transformations in unit operations, but only if the material can flow through them. Essentially, each unit operation receives a unique feedstock and produces a unique product to be collected, transported, and fed into the next unit operation. Such material-handling systems can only be expected to achieve design throughput if the system equipment is designed to the materials’ characteristics, over their full range of conditions. This requires quantification of flow properties to support the necessary customized equipment designs. Too often, assumptions or “library values” of a material’s properties are used as the basis for flow modelling and conceptual, and sometimes even detailed, design. This is especially true for hazardous materials like uranium ore, for which the additional precautions, costs, and time necessary for safe handling are often used to rationalize postponing or even bypassing testing. The surprises that often transpire in the wake of insufficient material handling consideration can have acute and costly effects. Fortunately, there is a better way.

Jan 1, 2020

By C. W. Drake, J. H. Walsh

"The Canadian Carbonization Re-search Association was formed during 1965, with seven founding members representing four integrated steel companies, two coal companies and one high-temperature tar processing company. The purpose of this paper is to review the circumstances which led to the formation of this new research association and to discuss its general objectives. Also discussed will be the organization of the Association, the nature of its relationship with the Department of Energy, Mines and Resources in the early stages, and some of the technical programs which have now been initiated."

Jan 1, 1967

By John L. Bonus

"WITHIN THE BROAD PARAMETERS implied by the title of my speech, I propose to deal more particularly this evening with a subject the many aspects of which have constituted the essential elements of one of the main thrusts undertaken by the MAC in the past two years, i.e., to create among Canadians a much greater awareness of the importance of mining and to demonstrate to them what are the many and varied benefits they derive from mining activities across their country. In other words, MINING - WHAT IT MEANS TO CANADA.I also intend to discuss some aspects of government-industry relationships.I am very conscious of the fact that I am speaking to an audience made u in large part of experts in several fields of mining and exploration activities. They will be familiar with many of the points I intend to discuss. However, without in any way suggesting that familiarity breeds contempt, might I emphasize that even in this particular forum there is justification for reiterating some of our basic philosophies and suggesting ways whereby they might be better understood and promoted.Let us first summarize the present dimensions of the Canadian mining industry."

Jan 1, 1971

By M. S. Badollet

Introduction Very little fundamental research has been done on asbestos fibre to cake maximum advantage of its properties and to determine in what commercial products it can best be utilized. For the research chemist who is associated with asbestos development work, a thorough study of mineralogical information on asbestos deposits would furnish reliable information on the rock formations and the mineral impurities closely associated with the asbestos. Furthermore, ?he must have an intimate knowledge of the uses of the fibre in various products so that he can visualize the importance of the fibre and the role it plays in industry. Some of the properties of asbestos fibres such as strength, composition, length, harshness or softness, and mineral associates are of considerable importance to the manufacturer because they are responsible for many production difficulties. Fibre Strength It has been known for some time chat asbestos filaments have considerable tensile strength. These strengths have been referred to merely as 'weak' to 'very strong'. Not until recently have numerical values been applied to the strengths of asbestos fibres. But today we can take a thin fibre filament and mount it between two holders and apply a gradually increasing load or pull until the fibre breaks. By measuring the cross sectional area of the filament and the amount of load applied, we can calculate the tensile strength of the fibre in terms of pounds per square inch. This type of test is slow and rather difficult, but the fundamental data obtained furnish important basic information that can be applied to mechanical processing equipment and to certain asbestos products.

Jan 1, 1948

By L. J. Cunningham

I THINK it can be safely said that no mining operation, whetl1er open-pit or underground, is ever entirely free of water. It follows that every ton of ore bears a charge which represents, either directly or indirectly, the cost of keeping the mine workings as dry as possible. Water problems occur in all phases of mining operations. They cause difficult and costly drilling conditions during the exploration stage, they often seriously delay mine development, they can slow mine production and reduce efficiency, and they are a continued burden over the life of the mine. It is therefore in the interest of all mining men to be familiar with the methods and materials used for grouting. The most common grouting material is cement. Cement grouting is old and well established, and many engineers are familiar with its uses and limitations. The technique of cement grouting is relatively simple and fairly well understood, and the materials utilized are relatively in-

Jan 1, 1962

By PAULL. BROUGHTON

Commercial deposits of sodium sulphate are harvested from alkaline lakes that are widespread throughout semi-arid southern Saskatchewan and adjacent southeastern A lberta. Concentration of sodium sulphate occurs in undrained basins under semi-arid conditions. Precipitation runoff from land adjacen1 to 1hese basins leaches 1he mineral from the soils and carries it in solu1ion 10 the basins. The process may be largely subsurface, wherein spring seeps feed basins associated with buried (preg/acial) river valleys. Evapora1ion during summer concentrates salts in the brines, and chilling of water below sa/Uration poin1 during win1er resu//s in deposi1ion of sodium sulpha1e (mirabili1e) crystals on lake bo//oms. Sodium su/pha1e, commercially known as sa/1 cake, ranks second only 10 po1ash in cen1ral-wes1ern Canada's nonme1allic mineral production. // is recovered from su,face brines, directly from intermittenl salt beds, and, until recently, by solution mining of shallow subswface deposits. Sodium sulphate is extrac1ed from seven alkaline lakes and sail f/a1s in Saska1chewan and one in Alberta. Annual produc1ion is approxima1e/y a halfmillion tonnes. Manufacture of kraft paper is the mos1 significanl marke1 for salt cake, but addi1ional quantifies are used in the glass and detergent manufac1uring indus1ries.

Jan 1, 1984

By M. Piche

The western part of the Hauy Formation of the Opemisca Group, occurring near the town of Chapais, is described in this paper. As it has been defined previously, the Formation is composed of a succession of subaerial andesi tic lava flows with some interbedded proximal volcaniclastic sediments. Towards the East, these volcanics yield to coarse grained fluviatile sediments having similar composition to the interbedded lavas. Further east, the composition of these sediments is more arkosic with dioritic and tonalitic fragments. It is proposed that these arkosic sediments are a part of the Stella Formation which has been described by Dimroth et al. (1982).

Jan 1, 1984

By John A. C. Fortescue

There is a need for better communication between scientists who plan and carry out mineral exploration research in glacial terrain and the exploration geologists who look for mines. In this paper, four ways in which workshops could be used to close this communication gap are described and discussed in relation to the solution of this problem in Canada.

Jan 1, 1973