Search Documents

By J. L. Miller, R. W. Burns

This paper sets out the various phases of bringing a merchant bar mill into operation from feasibility consideration through financing, design and scheduling to completion.

Jan 1, 1967

By T. Donkin, B. Patterson, M. I. Guthrie, J. T. Ross

"The interest in the use of sensor-based particle ore sorting has increased significantly with the recent advances in the sorting technologies and higher capacities per unit. This technology has the potential to provide great value in processing lower grade ores from the mine whilst delivering higher grades to the mill as well as in upgrading waste rock into ore. Typically, the focus is on the amenability of the ore to ore-sorting and associated reductions in the consumption of energy, water and consumables. However, layout has a significant impact on the installed cost of a concentrator and the layout impacts from fitting an ore-sorting circuit into the concentrator plan need to be carefully considered. This paper examines layout considerations that play an important role in ore sorting projects. These include additional crushing and screening requirement, transportation of the rejected material back to the waste stockpile (mine fleet requirements) and effects on concentrator footprints.INRODUCTION Ore sorting has been practiced throughout history with an early report by Agricola in 1556. Metallic and non-metallic minerals were extracted from rocks by laboriously breaking them with hammers and picks and hand-picking selected material with higher grade off a table. The concept has not changed but the sorting technology has evolved significantly over the last 20 years. Ore sorting is usually a dry process in which a portion of the material is rejected based on mineral properties and/or grade. The methods used for sensing ore particles cover a large range of physical properties. A variety of sensors are available that differ on the discrimination technique that is used, which include: photometry, radiometry, conductivity, magnetism, microwave, X-ray transparency: X-ray transparency and luminescence and UV fluorescence (Sivamohan and Forssberg, 1991; Wotruba, 2006). There are two main ore sorting techniques: particle ore sorting and bulk ore sorting. According to Nadolski et al (2018), the potential for sorting is determined though analysis of grade heterogeneity within the orebody (greater heterogeneity represents more opportunity to add value to a project) at the scale of the intended sorting unit size."

Jan 1, 2019

By P. O. Parfitt

At the McIntyre mine, there are two distinct operations: a gold mine with narrow veins, mined by cut-and-fill methods, and a copper mine with large, open, long-hole stopes. The application of the Critical Path Method to scheduling work in the copper mine, where it has been used successfully for several years, is de-scribed briefly. This application is relatively simple. Use of C.P.M. has now been extended to the gold mine. To replace the former method of scheduling from bar-charts, a procedure was developed for scheduling automatically. To handle an operation of this size and complexity, a computer was essential. Improved schedules are now being produced, with a saving in time.

Jan 1, 1967

By E. Thune, F. Stålesen, E. O. Stensholt, O. M. Dotterud, E. E. Henriksen, P. O. Ramsdal

"The development and commercial operation of the Falconbridge chlorine leach process have been described in papers in 1985 and 1987. Since this time, various process improvements have been implemented and the capacity of the Kristiansand refinery has been increased to 85 000 t/y Ni, 40 0000 t/y Cu and 4500 t/y Co. The focus has been on continuous improvements in productivity, the use of energy and other costs. Several environmental issues have also been eliminated or reduced since 1987. IntroductionThe first nickel refining operation in Kristiansand, Norway, started in 1910 based upon raw materials from Norwegian mines. In 1929, Falconbridge Nickel mines purchased the refinery to acquire information and the patent rights to the Hybinette refining process that was practised at the small Kristiansand refinery. Falconbridge ownership has now, for more than 70 years, provided a strong base regarding raw material supply, financial resources and technical support for further expansions and major technical improvements at the refinery.The main concepts of the new chlorine leach process were developed in the laboratories from 1966 to 1969 and the process was piloted from 1970 to 1972. The main stages in the commercial plant were started in the 1975 to 1981 period. After 1981, there have been a number of process modifications, plant expansions and improvements to operating practices. The developments up to 1988 have been described in previous publications (Stensholt et al., 1986, 1988).This paper presents an overview of the process and how it is practised at Falconbridge Nikkelverk AS (FNA) today and describes some of the main changes that have been implemented since 1988. During this time, the nickel capacity has been expanded from 54 000 t/y to 85 000 t/y and the cobalt capacity from 2000 t/y to 4500 t/y. The paper describes how these expansions were achieved together with continuous improvements in operating efficiency and also gives an overview of the main environmental concerns at the refinery."

Jan 1, 2001

By Lorrie Fava

Two needs in the mining industry, to enable overall process improvements, are open systems and network connectivity in underground mines. The Pando project, a collaboration between Symboticware, Vale and Xstrata Nickel, and supported by CEMI, addresses these issues, and leverages the solution platform to deliver intelligent applications. An open system is one that uses publicly available standards for its key interfaces. Vendor-neutrality and ease of information flow are two main benefits that result from the use of open systems. By facilitating the interoperability of systems, open systems allow information to be available when and where it is needed for decision support. Network connectivity in underground mines is typically limited, with hotspots in strategically chosen areas that are relatively static. Mobile equipment moving through a mining work cycle experiences intermittent connectivity; in this situation, seamless remote equipment monitoring is impossible. The Pando project establishes an open technology platform, adhering to the IREDES and OPC UA standards. It enables the collection and integration of information generated by mobile equipment? seamlessly while there is a network connection, and as a store-and-forward gateway to manage intermittent connectivity. The platform capabilities are leveraged to support embedded intelligent applications. This open platform, the SymBot, is a rugged hardware and software device. The platform complies with open standards for industrial automation and systems interoperability. The SymBot platform is capable of providing advanced real-time decision support at the device level, and is designed to be remotely configurable. Applications being developed through the Pando project include engine monitoring, a dynamic load weighing system, machine location monitoring and automated activity monitoring including production and maintenance reporting.

Oct 1, 2010

By D. F. Scott

"DEFINITION OF THE REGION AND ITS BOUNDARIESTHE REGION of Western Canada covered by this re-port lies between the Precambrian rocks of the Canadian Shield and the structurally deformed rocks of the eastern Cordillera, extending northward from the international border to the 60th parallel. It is some 487,000 square miles in area, with a total sedimentary fill of about 535,000 cubic miles0>. It includes parts of the prairie provinces of Manitoba, Saskatchewan and Alberta and the northeast corner of British Columbia and forms part of the geological region known as the Interior Platform, commonly referred to as the Western Canada Sedimentary Basin. The bedrock comprises carbonates and evaporites of Paleozoic age that lie on Precambrian crystalline rocks and are over-lain by a relatively thick blanket of Mesozoic and Tertiary elastic rocks. The nearly flat-lying bedrock, covered by a thick mantle of glacial drift, forms the Interior Plains physiographic province."

Jan 1, 1970

By Mario A. Morin

Mine design, planning and scheduling is a very complex, iterative process comprising several interrelated and interdependent activities. Understanding how this process works, identifying the critical pieces of information and the decisions to be made is key to initiating business process improvements (BPI) or business process reengineering (BPR) activities. Fundamental to most BPI and BPR work is some form of systems analysis. Structured Analysis is a powerful systems analysis technique that is well suited for modeling and analyzing complex process activities. Through a series of diagrams, this paper presents a vertical slice through the analysis work performed for formally describing the underground hardrock mine design and planning process. These diagrams illustrate how simple graphic constructs can be used to decompose the most complex situations into easily understandable diagrams that facilitate understanding, communication, improvement and reengineering.

May 1, 2002

By G. V. Sirianni, G. E. Viens, R. A. Campbell, G. N. Banks, R. L. Sachdeva

"A combined shaft-electric furnace for the smelting of ores and the melting of metallized iron pellets is being developed. The materials are preheated, and in some cases pre-reduced, in the shaft before being transferred to the electric furnace, where melting or smelting is completed. It has been demonstrated that this combination of equipment will enable much of the relatively expensive electrical energy to be replaced by cheaper energy in the form of oil or natural gas, and preliminary experiments indicate that the total energy requirements for a melting or smelting operation are significantly reduced. Projections based on results obtained from the preliminary experiments indicate that further improvements will be possible when certain modifications to the equipment are completed."

Jan 1, 1968

By Jack G. Hazan

The Critical Path Method is the modern scientific answer for solving the planning and scheduling problems inherent in today's complex projects. With this method, nothing is left to chance. All resources are controlled and kept to the minimum. The various phases are properly planned and strategically determined. Optimum conditions are evaluated for the most economical and fastest way to complete a definite project. The method must be fully understood and implemented with positive data and continuous feedback to obtain the best results. This paper covers the various aspects of the Critical Path Method and mentions some of its applications in the mining and metallurgical fields. T 0 progress to a higher state of human welfare necessarily involves sacrifices. The greatest sacrifice is to relinquish social freedom in favour of economic freedom. In the old days, for example, a cobbler was free to work at whatever time of the day he chose; today, he can't. He is now forced to adapt himself to environment and to work at stand-

Jan 1, 1965

By Edgar Stansfield

Introduction First, I should define more closely the vague term 'recent work' that appears in the title of this paper. Following the period of depression that was an aftermath of the first Great War, the Research Council of, Alberta carried on for ten years without a Council and without a financial yote by the Legislature. In November, 1942, a new Council was formed, under the chairmanship of the Hon. N. E. Tanner, Minister of Lands and Mines, and a vote was granted by the Legislature early in 1943. By 'recent work', I mean work during the present regime. The Council is now going full steam ahead, or would be if it could get suitable technical assistance and required apparatus and materials. Lack of these has so far made unnecessary my responsibility for seeing that we do not exceed our estimates. The Annual Meeting of the Research Council will be held in November (1945), and at that meeting the programme of work for next year will be discussed. The present time is therefore the correct time for any of you who may have ideas as to work which might profitably be undertaken by the Council, to submit these ideas for consideration. I propose to discuss my subject under several headings, and to give enough of these to show that the Council has wide interests.

Jan 1, 1946

By George W. Bain

Mr. Geo. W. Bain: Dr. H. C. Cooke's discussion of 'The Geology and Mineral Deposits of the Harricanaw and Bell River Basins' possesses many of the elements of a good political address; perhaps his long residence in Ottawa has some bearing upon his method of discussing geological work. The three essential parts of the address are all included. First, the plank - "Contributed discussion on the Geology and Mineral Deposits of the Harricanaw and Bell River Basins"; second, the personal attack upon the opponent, to show antipathy to the opponent as well as to his ideas; and third, controversion of a number of statements, which have been made to appear as planks of the opponents platform, even statements and work which are in no way connected with one under discussion. In the following pages, I will confine my attention to a defense of my work in the Harricanaw and Bell River basins, leaving discussion of the other areas mentioned by Dr. Cooke until results of the re-surveys are published. It is intimated that it was impossible to make a geological examination of an area of 1,600 sq. miles on a scale of four miles to the inch (base map supplied) in three and a half months, because "the area is accessible only from the railway along the northern edge together with a few roads close to it, and from rather wide separated streams?. There is one way, known to most geologists, whereby a place can be reached other than by railway coach or motor boat, and that the oldest of all -- walking. Most of the region was reached in this fashion. The boundaries of all the 18 townships included in the map are surveyed, nine are divided into lots, and the north-south and east-west centre lines of most of the others are surveyed and have mile-posts placed.

Jan 1, 1927

By A. McLean, Q. R. Yang, Y. D. Yang, G. F. Zhang, P. Wu

A considerable amount of waste slag from the pyrite roasting process is discharged every year. Recovery of iron from the waste slag is of great interest for comprehensive use of mineral resource, reduction of environment impact and improvement of economical benefit to related companies. The objectives of the present work are focused on: (1) Compare various procedures for recovery of iron from the waste slag and select a best procedure for industrial trial which is roasting of the waste slag under reducing condition followed by magnetic separation; (2) Investigate the optimum conditions for maximum recovery of iron from the waste slag. The experimental result shows that under the treatment condition found in this work about 36 to 40% of the iron oxide was recovered from the waste slag, where the iron content in the concentrate is 57%. The total recovery ratio of iron, up to 70%, from the waste slag was achieved. After the treatment, sulphur content in the waste slag was reduced significantly and gangue materials, such as SiO2, Al2O3 and TiO2, were reduced effectively.

Jan 1, 2011

By Louis Frost

The coal-mining industry of Nova Scotia, particularly of the island of Cape Breton, today faced as no other industry with economic problems calling for progressive engineering with production on an economic basis, must soon enter upon a phase of reorganization wherein all factors conducive to the cost of producing coal relative to the prolongation of the life of the collieries with the ultimate winning of the maximum submarine area must be closely reviewed. Bearing this in mind and applying the process of elimination to coal-mining costs generally, we are left with only three channels through which we may approach the problem of cost reduction in producing coal: (a) intensive mechanization (b) reduction in the cost of labour (c) reduction in the cost of materials. Assuming that mechanization has reached an economic stage and that labour costs have reached an economic limit, we must turn our attention to the general material costs, which may be classified as 'live' and 'dead' costs. The former take in all things which can be accredited with a fractional depreciation and written off the balance sheet over a period of years. On the other hand, the ?dead'costs-of which the cost of supporting the underground workings form part must be completely written off: for these, no return may be expected, other than the economic return in the reduction of the cost per ton of coal produced.

Jan 1, 1928

By W. E. Newton

THE following notes are offered primarily to show that industrial minerals or their products have a much more important place in the metallurgical industry than is perhaps generally realized, and with the hope also that some statement by the metallurgical consumer of the relative merits of various materials for particular requirements or services will l;>e of value to the industrial mineral producer. These notes are not in any way presented as complete. Also, some of the statements made may be debatable. The grouping adopted is as follows: (1) Refractories; (2) Fluxes; (3) Construction materials; and ( 4) Miscellaneous applications. Fuels are not dealt with in the present paper. REFRACTORIES GENERAL: Refractories are materials which will withstand high temperatures with-out melting or becoming markedly soft or pasty. While their primary function is to withstand heat, they are usually called upon to resist one or more of the following destructive influences: abrasion, pressure, corrosion by slags or fluxes, and rapid changes in temperature. Refractory materials may be conveniently divided into three classes: (1) Acid refractories-consisting of silica, or containing silica as their chief constituent. They combine more or less readily with metallic oxides, forming silicates, and are hence termed 'acid'. The most important of these are quartz, quartzite, siliceous sand, tripoli, Dinas rock, and ganister. Most fire-clays, although generally considered neutral sub-stances, contain relatively small amounts of free silica and are, to that extent, acid. (2) Neutral refractories-the term is merely relative in most cases, since, at high temperature, many of the refractories that are classed as neutral will react chemically with a strong base, functioning as a weak acid; or, conversely, with a strong acid, functioning as a weak base. Chrome and graphite are the most nearly neutral of all the commonly used refractory materials.

Jan 1, 1936

This paper discusses three case studies conducted at Highland Valley Copper mine (HVC) that illustrate operational improvements and insights which resulted from using the McGill University gas dispersion sensors. In the first study, the superficial gas velocity (Jg) sensor was used to implement a gas profiling control strategy for the rougher, scavenger and first cleaner cells in the Cu/Mo separation circuit. The data showed a 40% reduction of down-the-bank Cu recovery at constant Mo recovery which resulted from operating the cells at the target profiles. In the second study, the bubble size analyzer was used to better understand two mechanisms of bubble formation in the two flotation columns that make up the final Mo cleaning stage: the conventional rubber-sleeve sparger and the Microcel(TM) system. The data showed a considerable reduction of bubble size in the Microcel column which resulted in a significant increase in concentrate quality (1-2% Mo absolute) and a dramatic (4-5 fold) increase in concentrate production rate compared to the typical operation. The estimated economic benefit resulting from the improved column flotation operation was an overall 4% increase in Mo circuit recovery. In the third study, real-time measurements obtained from the gas holdup and bulk density sensors were used to infer the pulp density (% solids) in a rougher cell of the bulk flotation circuit. Validation tests demonstrated that this approach provides reliable pulp density measurements. Although promising, more work is required before implementing this approach at HVC.

Jan 1, 2009

By E. B. Wright

THE property of Falconbridge Nickel Mines, Limited, is in Falconbridge township, approximately thirteen miles northwest of Sudbury. From the mine and townsite, a gravel road leads to Sudbury and a branch line of the Canadian National railway to Sudbury Junction. The ore deposit is at the southeastern corner of the 'Sudbury Basin'. It lies in a sheet-like mass, striking in an east-west direction, between norite to the north and greenstone to the south. The general attitude of the ore-body is vertical, but with frequent variations in dip of as much as 10° to the north or south. The deposit is very irregular in outline, the width varying from a few feet to eighty or ninety feet. In the vertical plane, rolls are frequently encountered. Gouge is very often present at one or both ore contacts. The norite to the north shows much jointing. The chief ore minerals are pyrrhotite, pentlandite, and chalcopyrite. The nickel content of the ore is usually double the copper content, average assays ranging from 2 to 2.5 per cent nickel and 1 to 1.5 per cent copper. The ore is of three main types: massive, breccia, and disseminated. The breccia ore, the most common type, consists of sulphides containing rounded inclusions of highly-altered country rock, which, in places, are so large that sorting is necessary in the stopes. In the norite, the breccia ore may grade into disseminated sulphides, which frequently are sufficiently concentrated for profitable mining. In places in the breccia ore, concentrations of solid sulphide masses occur. Until early in 1935, all mining at Falconbridge was by shrinkage scoping, but this method was found to be less and less suitable as greater depth was attained. When mining had reached the 1,000-foot level, ore drawn from large shrinkage stopes was found to have been diluted as much as fifty per cent by sloughing of the wall-rocks, caused by increased rock pressure and insufficient support. It was apparent that this method of stoping was un-suitable and -Mr. E. J. Martin was engaged to superintend the introduction of a method of cut-and-fill stoping.

Jan 1, 1938

The extractive industry has the potential to impact the health and well-being of workers, families and surrounding communities. In the current environment of social performance, project planning considers that activities should be conducted in the best environmentally, socially and economically acceptable way across the development cycle (i.e. from exploration ? post-closure). In this context, health impacts of mining can be mapped and extend over the Life of the Community and can encompass worker injury and disease, exposure to communicable and non-communicable diseases, and health outcomes specific to family and community health and well-being outside the fence. To contribute to an emerging field focused on Health and the Extractive Industry, this paper reviews and compares health activities extracted from social and environmental reports published by selected major mining, oil and gas companies with operations in Australia and Canada. The objective of this review is to map corporate approaches to public health management across our previously developed Life-of-Mine within Life-of-Community (LOMLOC) framework in order to identify and compare trends and behaviour in corporate health investments across the project cycle, as well as identify the level of prevention targeted by this investment activity (i.e. primary, secondary and tertiary prevention of detrimental health impact). With the extractive industry facing ongoing rapid growth worldwide, this paper provides preliminary comparative information about corporate health spending by some companies in Australia and Canada. This information serves as a resource for minerals industry managers, civil society and regulators regarding current health management approaches in this sector.

Aug 1, 2013

By H. Q. Fan

Construction equipment is an important type of resources of heavy construction contractors. Since equipment breakdowns can cause project delays and significant financial losses, the contractors are eager to know those factors causing equipment failures directly or indirectly, related to equipment design, maintenance, and operations. Although Bayesian network can be used for diagnostic analysis of failure events or making predictive analysis, building a Bayesian network for such purpose can be difficult as the cause-effect relations can be subjective and their conditional probabilities change with a wide variety of causal factors. A hybrid approach is proposed in this paper to update the Bayesian diagnostic network structures and parameters using real life data, the conditional probabilities and cause-effect relationships can be dynamically updated with observed failure records to reflect the real life situations of a complex equipment system. A case study is conducted to show the benefits of the hybrid approach in construction equipment diagnostic analysis.

Aug 1, 2013

By H. Stutchbury

Alberta is labouring, and has laboured, under serious difficulties in the marketing of ?her coals, due to a number of conditions which now obtain, but all of which appear capable of solution, and their elimination would insure a very largely increased market for the vast coal resources of that province. It is perhaps necessary to again mention the fact that 15 per cent of the world's coal resources are to be found in Alberta; 21 per cent of that of North America; 72 per cent of that of the British Empire, and 87 per cent of that of all Canada. While we talk largely of the great wealth of Canada, the immensity of her vast natural resources, it is axiomatic that the mere presence of any natural product in a country does not in itself constitute wealth for that country, unless these raw materials can find a market, either in their raw state, or by the process of manufacture. There are many factors, however, which enter into the marketing of any commodity. The chief of these, in my opinion, is price competition. High costs of production materially reduce the radius in which any product can be marketed, and this applies particularly to coal. Mining costs in the province of Alberta are necessarily high at the present time, due in a large measure to the ease with which the 'gopher hole' mine can be opened with small capital.

Jan 1, 1925

By W. D. Mulholland

"I ASSUME that any effort on my part to deal with the question of the importance of the mining industry is going to be largely an exercise in preaching to the converted, but there are one or two aspects that I'd like to particularly mention.The first is that, in terms of almost all factors, the mining industry is a very important industry in Canada. It is important in terms of employment in relation to the gross national product of Canada and it is particularly important in the international trade of Canada. So far from being insignificant domestically, it is also an extremely important factor in the international picture. That's an important point to bear in mind, because as we talk about all the other matters we never can lose sight of the fact that mining management always has to be conscious of its international competitive position. It is something that one forgets at one's peril, and to a somewhat greater extent than is true of many other industries, those managements have to compete in an international context for their markets, to some extent for their people for specialized skills and of course for finance. In the evolution of domestic policies it is a very, very perilous step to take to impair that competitive ability of the domestic mining industry."

Jan 1, 1972