Search Documents

By G. Stokreef, B. R. Davis, M. Kadiyski, T. LeBel, Alvear Montenegro, R. Parra, V. Montenegro

A drop tower and methodology were developed to study the impact of mineralogy on the flash combustion behaviour of copper concentrates. Reaction shaft conditions of a flash furnace were simulated using a drop tower reactor and different molar ratios of oxygen gas to sulphur in the feed. Five feeds were tested in the drop tower including pure minerals chalcopyrite and pyrite as well as two mineralogically distinct copper concentrates and a blend of the two. The behaviour of each of these five feeds were evaluated through analysis of the solid combustion products for elemental sulphur, mineralogy and particle size. Desulphurization curves for each of the feeds were produced. It is thought that the desulphurization behaviour of pure minerals can be used to estimate the behaviour of a concentrate and that a blending recipe could be developed, which can optimize the chemical and mineralogical inputs to the flash furnace and guide operations on the optimum furnace conditions. Overall, the drop tower has proven to be a useful tool for studying flash combustion processes. Experimental results suggest that mineralogy has a significant impact on the conditions required for the production of matte with consistent grade. This finding is especially significant for custom smelters, which may see several different blends in a day. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process that is used to produce copper matte from copper sulphide concentrates. Dried concentrate(s), silica flux, and secondary materials are blended to a target chemical composition, typically given by the Cu/S ratio, before processing. This fine, dried feed is dispersed throughout the heated furnace reaction shaft with an O2-enriched reaction gas. The particles heat up in the shaft of the furnace, ignite and undergo reactions that pre-oxidize the iron sulphide and some of the impurities in the feed. Oxidation reactions in the shaft of the furnace desulphurize the feed and produce an SO2-containing off gas. The reacted particles fall into the furnace settler and separate into a Cu-rich matte and an iron-silicate slag, while the SO2-containing off gas is carried out of the furnace for heat and dust recovery, as well as H2SO4 production. Some concerns during operation of the furnace are dusting, over or under oxidation of the feed, and a stable flame.

Jan 1, 2019

By Carricajo T., S. Nazari

This paper discusses a unique dynamic solution for optimizing comminution area in real time. The proposed technology is a combination of model predictive controller, optimization methods and real-time digital twin for mineral processing. For grinding area, the ultimate goal of an effective control strategy is to maximize the mineral processing, reduce energy consumption and stabilized size classification. To have a continuous and effective comminution operation, a reliable control system that minimizes the need for human intervention is necessary. The implemented advanced control strategy for comminution area consists of two layers in hierarchical structure. The lower layer objective is to stabilize the process stabilization using model based predictive controller (MPC) technique. The unique MPC used in this layer is called BrainWave™ chosen for its robustness, convergence and delay handling; furthermore, the developed platform offers stable and repeatable solution and has short implementation time. The upper layer is a supervisory control, which sends the preferred process operation points to the lower layer to drive the process towards optimal performance. The goal of this layer is to optimize the process targets, as well as making decision. To increase process performance, automatic ore characteristic adaptations are implemented in this layer. A digital twin of comminution area is built in the second layer that runs amongst the process in parallel. By communicating, the process data in real time, a virtual densitometer is built that is being used in our advance process control strategy. Our control strategy has been developed, tested and implemented in various areas of a copper concentration plant. The targets for implementing advance process control are usually increased throughput, decrease energy consumption and variability reduction in particle size distribution. Overall, the results showed in different mine sites are increase throughput between 2 and 5%, specific energy consumption reduction about 15% and process variability reduction up to 60%. In this paper we discuss the results of the recent implementation of this technology on Minera Los Pelambres, Minera Collahuasi and CAP Minería. Their concentrator plants have installed control systems with the most updates optimization features, for SAG mill, ball mills and thickeners.

Jan 1, 2019

By Liguang Wang

The froth phase in flotation has received much less attention than the pulp phase despite the fact that froth stability plays an important role in determining flotation performance. Froth stability is largely determined by the stability of thin foam films, which in turn has a strong correlation with the critical rupture thickness (Hcr) of the films. In the present work, a new approach to predicting the Hcr values of thin foam films in flotation froth phase was proposed and examined. The Hcr values were calculated using an advanced capillary wave model with input parameters being surface tension, film radius, capillary suction pressure, and intersurface force. The intersurface force was estimated by using the Stefan-Reynolds lubrication approximation to fit the measured thinning rates of single foam films formed in a Scheludko ring cell, where the film radii were less than 50 microns and were kept constant during the film-thinning process. A comparison between the predicted and experimental Hcr values was made for the films with the use of sodium chloride as background electrolyte and in the presence of various frothing reagents such as methyl isobutyl carbinol (MIBC), polypropylene glycol with an average molecular weight of 400 (PPG400), and sodium dodecyl sulphate (SDS), at different concentrations and film radii. It was found that the model correctly predicted the trends of Hcr-versus-concentration and Hcr-versus-film radius curves. Moreover, the predicted Hcr values matched well with the experimental ones of the foam films containing either SDS or PPG400. For the foam films containing MIBC, however, the model overpredicted the Hcr values. The reason for this discrepancy was discussed.

Jan 1, 2016

By David L. Huston, Wouter Bleeker, Bruce E. Taylor, Ron Cook, Bob Stewart, Elizabeth R. Koopman

"Abstract-Detailed oxygen isotope mapping of rhyolites in and around the Kidd Creek mine indicates that the orebodies are associated with relatively low (<12‰) whole rock values that extend up to 200 m laterally from ore. The zone of low d18O values is overlain stratigraphically by a carapace of higher (>13‰) values that extends up to 1.5 km laterally from and 300 m to 500 m above ore. Immediately above the stratigraphically highest orebody this carapace is cut by a zone of lower d18O values extending from the ore zone. Zones of higher d18O values also occur in massive rhyolite bodies that occur in the footwall of the orebodies.The zone of low d18O values partly coincides with a Na2O depletion anomaly associated with hydrothermal alteration, except that the Na2O depletion anomaly has a greater lateral extent, and the low d18O anomaly extends farther into the stratigraphic hanging wall. These data suggest that d18O mapping may detect hanging wall alteration above massive sulfide bodies more effectively than conventional lithogeochemistry. Zones of high d18O values, which define zones through which large quantities of low-temperature hydrothermal fluids have passed, may also have usefulness in exploration.Oxygen isotope variations at Kidd Creek record three stages of a hydrothermal system that evolved in temperature with time, as follows: (1) an early, low-temperature event that produced rocks with high d18O values, (2) a high-temperature event that produced rocks with lower d18O values, and (3) a later, low-temperature event that also produced rocks with high d18O values. The high d18O sig- nature of the massive rhyolite was recorded during early-stage, low-temperature (<200°C) alteration, and was probably preserved owing to decreases in permeability associated with low-temperature silicification. The low d18O signature of cherty breccia and chloritite was recorded during the thermal peak at >300°C. High d18O values in the carapace above the deposit were recorded as the hydrothermal system waned."

Jan 1, 1995

"This paper discusses the use of risk assessment and risk management techniques within the Australian underground coal mining industry, within the context of geotechnical risk. The industry works within a pro-active, “enabling” legislative framework, where companies and management apply a range of risk assessment tools as part of their everyday management processes. Different geotechnical risk factors and approaches are reviewed, together with application examples – ranging from mine planning and design, operations, and accident investigations.A particularly powerful resource in each of the above stages of geotechnical management is the RISKGATE system. RISKGATE is an assembled “body of knowledge” structured under different topics across the Australian coal industry, of which three topic areas address rock mechanics issues for both the underground and surface mining sector. This paper will provide an overview of RISKGATE in the context of risk-based rock mechanics applications in underground coal mining."

Jan 1, 2015

By P. J. van Staden

Several differences exist between the columns used for laboratory simulations of heap leaching and commercial heaps. Column walls support part of the weight of the ore and restrict the particle packing arrangements. Columns are typically of a diameter that is smaller than the dripper spacing to be used on the commercial heaps. The stacking practices that cause segregation and stratification on heaps are absent from columns. Intuitively, these physical differences would be expected to be the reasons behind the observed differences between column and heap leaching performance. But how can they be quantified, and what is the magnitude of the differences? Could some of these differences be built into column leaching experiments in order to better simulate commercial-scale heap leaching performance to ease the scale-up calculations from column leaching data? Alternatively, could heap construction practices be improved so that the ideal performance obtained in columns could be emulated on heaps? Data from a few heap leaching cases studies that permit direct comparisons between column and heap leaching performance is analysed, to reveal the extent of the differences in resistance to mass transfer. Discussion is provided on the implications for column and heap leaching practice, and for scale-up design procedures. INTRODUCTION Differences have been known to exist between leaching performance observed in laboratory columns and that of commercial-scale heaps. Both the heap leaching kinetics and finally achievable extent of extraction are generally found to be inferior in heaps compared to that achieved in columns. Heap leaching design engineers extrapolate the anticipated heap leaching performance by multiplying the time-axis of a column-leaching curve by a factor of about 2 and the extraction-axis by a factor of about 0.8, as explained by Jansen and Taylor (2002), Scheffel (2002), John (2011) and Scheffel, Guzmán, and Dreier (2016). The procedure is illustrated in Figure 1 by means of a hypothetical example. The solid line represents the leaching performance observed in a laboratory column, and the dashed line represents the anticipated leaching performance of a heap, extrapolated from the column leaching data using these empirical scale-up factors.

Jan 1, 2019

By Laxman M. Amaratunga

"The fine fraction of tailings is usually excluded from the backfill process and generally disposed on the surface in tailings ponds. Because of the ever increasing demand for fine grinding in the extraction process for improved liberation of valuables in the ore, increased production of fines in the tailings has resulted. The negative impact of surface impoundment of tailings on the environment is well known. Amaratunga and Annor (1989) first presented a concept of fine tailings agglomeration for backfill.This paper presents the development of the novel cold-bond tailings agglomeration (CBTA) technology for non-reactive fine gold mill tailings. For cold-bond agglomeration regular portland cement was used as a binder. In order to cut costs, alternate binders such as lime, and blast furnace slag cement were examined. The effects of binder dosage, curing time, and agglomerate size on the fracture load strength of the agglomerate were studied.Fine tailings agglomerates are mixed with coarse tailings or non-agglomerated fine tailings to make high density fill compositions to be used as underground backfill. Alternatively, the agglomerates can be used as aggregates for surface applications. The paper discusses the environmental and operational benefits of this total tailings utilization and disposal technology.IntroductionIn Canadian mines, mill tailings are probably the most commonly used material for backfill. However, only the coarse fraction of tailings is desirable for use as hydraulic fill or high density fills. The fines are disposed on the surface in tailings ponds since they are unsuitable for underground backfilling owing to the following factors:i) slow settling ratesii) longer percolation timeiii) excessive consumption of binder due to drainageiv) poor compactionFor improved value liberation more milling operations have resolved to fine grinding in their comminution circuits. Gold milling operations driven by down stream leaching processes grind their ores excessively fine. In general, gold mines use hardly any tailings for backfilling. This can result in periodic short falls and the need to search for alternate backfill material from other sources. Apparently, the gold producers are the most identifiable sector which suffer from a shortage of backfill materials ( Amaratunga and Annor, 1989)."

Jan 1, 1994

By C. B. Mapes, E. C. Dowling Jr.

"To reduce concentrate dewatering and drying costs, the Concentrator Division at Phelps Dodge Morenci, Inc. investigated available filtration technologies. Numerous methods were explored, including: drum, disk, belt, pressure, hyperbaric, and ceramic media filtration. An economic evaluation of the individual filtration technologies indicated the advantages of ceramic media filtration for Morenci concentrates. This paper discusses the technological development culminating in the first full scale application of ceramic media disk filters in North America. Low moisture contents are obtained at high production rates and greatly reduced operating costs.INTRODUCTIONPhelps Dodge commissioned the Morenci Concentrator Filter Plant in 1942 with four 8'6"" Dorr-Oliver cloth disk filters. That year, the filter plant processed 265,537 tons of concentrate grading 20.5% Cu. The filter cake production averaged 9.3% moisture. In 1944, the Extension Filter Plant commenced operation with three additional 8'6"" Dorr-Oliver cloth disk filters. This coincided with the expansion of the concentrator. Production that year totaled 451,567 tons of concentrate grading 23.8% Cu. Moisture averaged 9.4%.Through the years additional filter units have been added in response to increased concentrate production. An Eimco drum filter was installed on the extension side and an additional Dorr-Oliver disk filter was installed on the original side in the 1950's. In 1961, two 8'6"" Peterson disk filters were installed, one on each side to replace two worn-out DorrOlivers. The installation of four 10xl2 foot Peterson drum filters was completed in 1974, coinciding with the Metcalf Concentrator startup. An Eimco belt filter was installed later.The greatest change to concentrate dewatering at Morenci occurred in 1963 with the addition of a 10x60 foot rotary gas fired dryer. The installation also included a number of conveyors to deliver filter cake from both plants to and from the dryers. Other ancillary systems included dust scrubbers and their slurry pumps. The commencement of drying was undertaken due to the rapid increase in cake moisture as a result of the LPF process and the recycling of acid plant scrubber dust slurry from the smelter. In 1972, a second dryer system was installed to increase capacity."

Jan 1, 1993

By Joël P. T. Kapusta, Liam J. Watt

The last extended copper smelting and converting survey dates back to the 2003 International Copper Conference held in Santiago, Chile. The following year, the Minerals, Metals, and Materials Society of AIME (TMS) started a new series in its Journal of Metals (JOM) called JOM World Nonferrous Smelters Survey devoting its first Part to Copper. The copper smelting landscape has significantly changed in the past 15 years, both in geographical terms with the shift of copper smelting production from the Americas to China and in technological terms with the growing adoption rate of Top-Submerged Lancing (TSL) technologies and the development and implementation of Bottom-Blowing technologies. A copper smelting survey update, even if not as in-depth as the 2003 Copper Smelting Survey, is therefore in order. The authors will review the latest trends in copper smelting technologies and production worldwide in comparison to the landscape of the early 2000s. INTRODUCTION This 2019 copper smelting survey is different from previous surveys as our data does not originate exclusively from responses to a questionnaire sent to all the copper smelters. Our data comes from several sources. We are therefore very thankful to the International Copper Study Group (ICSG) and Wood Mackenzie for sharing some of their information and to ENFI, Outotec, and Glencore Technologies for helping us cross-check our numbers for the Chinese smelters, flash smelting, Ausmelt, and Isasmelt technologies. Our survey presents data reporting from a total of 96 operating copper smelters from around the globe, which is significantly higher than the 50 surveyed in 2003. Although secondary smelting numbers have steadily increased over time, this paper focuses on primary smelting operations with copper concentrate as feed material. The list in this survey is still far from complete, with missing information from several known smelting operations. The total primary copper production tonnage of the smelters we surveyed amounts to 18.3 million metric tonnes from 29 countries representing 92% and 94% of total world primary production for 2018 estimated by ICSG and Wood Mackenzie, respectively. This representation has increased from 2003 when the total was 9.71 million metric tonnes from 23 countries accounting for 73% of world production. The trends presented and analyzed within this paper have stronger significance because of the increase in production accounted for. The Chinese and Russian smelter information collected is more detailed than years past. Our complete dataset is summarized in Table 1 at the end of our paper.

Jan 1, 2019

By B. Krysa, A. Mitsui, T. L. Koehler

The presence of arsenic, even at trace levels, in copper processing leads to the risk of arsine gas where reducing conditions exist that can reduce any soluble arsenic present to its minus 3 valance state and generate hydrogen gas from the solutions. This risk is understood to be significant within the industry, particularly in the case of liberator cells where copper concentrations in solution are drawn down to remove the copper and impurities from the bleed stream. However, there are numerous other potential areas where the arsine gas risk exists including contact between active metal such as iron, zinc or aluminum and arsenic bearing solutions in pyrometallurgical dust treatment, refining and acid plant operations. In turn this breaks down to different mitigating strategies dependent on the risk scenarios considered; for example, how this risk interacts with Change Management, Confined Space Entry or Contractor Training. The ISO 45001 is an emerging standard meant to improve employee safety, reduce workplace risks and create safer working conditions all over the world. The paper shows a case study of how a framework consistent with the tenets of ISO 45001 has been used to provide a consistent assessment of this risk for a wide variety of copper operations and the expectations of how this may be used to effectively improve the effectiveness of barriers against future incidents. INTRODUCTION Arsine gas (AsH3), first identified in 1775, is a highly poisonous, colorless, non-irritating gas with a mild garlic odor that is heavier than air. Arsine gas is generated when reducing conditions are generated in the presence of hydrogen ions and arsenic compounds. Present permissible occupational exposure limit as defined by Occupational Safety and Health Administration (OSHA) as an 8-hour time-weighted average is ppm (0.2 mg/m3). Further increasing the risk, conventional respiratory protection utilizing half or full masks with gas filtering cartridges provide minimal protection against arsine. In copper processing plants, the risk of arsine generation is well understood in liberator cells, which are part of the electrolysis process. In this process, solutions containing copper are reduced in copper concentration removing not only the copper, but also arsenic, antimony and bismuth. The residual solution can be bled to control impurity build-up in the refinery. In this process, if the copper concentration is reduced to the point where As3- can form, arsine gas is generated via reaction with hydrogen ions generated during the plating process. The copper concentration at which arsine gas is generated depends on copper concentration at the cathode surface, the temperature and the acidity. As a result, there is always a risk of arsine gas generation in the liberator cell. Process measures to minimize or mitigate arsine evolution are tight control on final copper concentration, warm temperatures, fresh feed distribution and internal acid recirculation rates. Operator exposure protection measures are hooding, ventilation, arsine detection systems, restricted personnel access, automated shutdown controls and pre-defined evacuation plans.

Jan 1, 2019

By P. C. Holloway, M. J. Collins, K. R. Buban

Historically, there has been little incentive to process copper-arsenic concentrates by leaching, rather than via established smelting operations. However, with ever tightening environmental emission standards and more arseniferous concentrates being produced, increasingly sophisticated and upgraded off- gas handling facilities are required in smelting operations, generating greater quantities of challenging metallurgical dust. In this context, oxidative pressure leaching offers distinct advantages. The current state of pressure leach technology delivers high extractions from copper concentrates, while producing an environmentally stable process residue, without atmospheric emissions of sulphur dioxide or arsenic. However, as was shown in an earlier study, copper extractions and environmental leach residue stability are impacted negatively by arsenic levels above 2.5 to 3.0 wt%. In further studies on pressure leaching of copper concentrates, Sherritt has developed process conditions that allow even highly arseniferous (> 7 wt% As) feed materials to be converted into environmentally stable residues, with excellent copper extractions. At the same time, pressure leach residues can be generated that are amenable to silver recovery via direct cyanidation, without pre-treatment by lime boiling or hot curing. The results of pilot plant test work are discussed. INTRODUCTION As the production of copper has expanded over the years, resource exploitation has extended beyond relatively clean, high grade and easily accessible ores, and copper sulphide concentrates increasingly come with higher levels of contaminants, such as As, Hg, Sb and Bi, and lower copper and sulphide sulphur concentrations. However, as concerns on the impact of the emission of such contaminants into the natural environment have mounted, import/export restrictions have made the trading of copper concentrate more difficult, and, in particular, the export of concentrates with greater than 0.5 wt% As; under ever tightening environmental emission standards, these lower quality concentrates can be a significant strain on the off-gas handling facilities in smelting operations. The processing of arsenic bearing copper concentrates is, therefore, an increasing challenge as copper producers seek to exploit more complex mineralization and to extend the life of their operations. In this environment, processing arsenical copper concentrates with high temperature pressure leaching (>200°C) must be considered as an alternative to pyrometallurgical processing. Leaching kinetics for copper minerals at these temperatures are rapid and acid is generated for potential use in heap leach operations. Pressure leaching of copper concentrates eliminates gaseous emissions of arsenic and sulphur, while generating environmentally stable residues, as measured by the Toxicity Characteristic Leach Procedure (TCLP) (Kalanchey et al., 2007). Both medium and high temperature pressure leaching of copper concentrates have also proven themselves technically on an industrial scale (Marsden et al., 2004) with high copper recoveries.

Jan 1, 2019

By Szilvia Szabo, Jozsef Paulovics, Ljudmilla Bokanyi

"Waste recycling is one of the most important challenges of the XXI century. The recycling of wastes is closely related to and bases on the mineral processing. Many mineral processing techniques and equipment are applied in this field. The principles of the characterisation of wastes and design of technologies is rather similar to the classic mineral processing. Nevertheless, the diversity of the wastes and their complex composition and properties, as well as their environmental impact requires a special approach.Solar elements have sandwich structure of glass substrate and cover, as well as a very thin semiconductor layer. CdTe semi-conductor can be recycled by flotation. Within the RESOLVED (LIFE European Framework) R&D project on the recycling of solar elements the surface properties of pure CdTe semiconductor and pure glass were investigated by the measurements of zeta-potential using Zeta PALS Brookhaven instrument at University of Miskolc. Applied surfactants were: potassium ethyl xanthate; the anionic oxhydryl Aero Promoter 825 or Flotinor SM 35; the cationic Armoflote 43 or Armoflote 64, as well as Hostaflot LET (dithiophosphoric acid diethyl ester) and Hostaflot M91 (mercaptobenothiazole). The tested electrolyte was sodium-silicate. Zeta-measurements were carried out in full pH-range. Interfacial interactions were detected and interpreted. The basic results were verified by the flotation kinetic tests.Finally, the flotation technological experiments were carried out at a semi-technical scale using the real obsolete solar elements. The particle size at the liberation degree of 98% was as fine as below 5 µm. A special flotation cell providing the generation and distribution of very fine air bubbles was built. The pre-concentrate for the manufacturing of the test solar module was performed and transported to the BAM Institute (Berlin), the principal co-ordinator of the Project, and then further to the First Solar (USA) where a new panel was manufactured using recycled semi-conductor."

Jan 1, 2016

By Dirk Claessens

The term ?cost? is too small when describing the destructive power of safety incidents for mining companies. Breaches in employee or environmental safety are felt way beyond the bottom-line: human life can be taken; ecosystems tarnished; the ire of peoples, media and government inflamed; significant halting of production; and high levels of legal and financial challenges. According to a recent survey of Mining executivesi, ?ensuring workforce safety? was the most important issues identified above any other, with a plurality of 31 percent, reigning above capital projects, product efficiency, and equipment reliability. We accept that safety is a most paramount issue, yet for many reasons we keep approaching the problem the same way we have in the past. We need to stop doing the same things decade over decade and try something new. New innovations are significantly changing the fundamentals of how mining companies explore, excavate, produce, refine and distribute their valuable commodities. Technologies such as visualization, analytics, location awareness, and gaming simulation are making these enterprises smarter. Now, attention turns to an area we?ve long held as integral to our business: safety. By using the same breakthrough technologies that are changing our business, we can now boldly imagine ? and credibly strive for ? a world of zero incidents.

Aug 1, 2013

By J. Shibata, K. Manabe, A. Fuji, N. Matsunaga, D. Murakami, Yamaguchi University, T. Suzuki

"Spent hydrodesulphurization (HDS) catalyst contains rare metals such as cobalt, nickel (Ni), molybdenum (Mo), and vanadium (V). The overall objective of this project is to develop a hydrometallurgical process that provides a degree of high recovery and selectivity of these rare metals from spent HDS catalyst. As a part of this project, this study focused on (i) development of a solvent extraction-precipitation stripping process for separation of Mo and V from solutions and (ii) optimization of grinding conditions of alkaline leaching residue for selective Ni sulfuric acid leaching against aluminum (Al). Experimental results showed that effective separation between Mo and V can be achieved by the two-stage process; solvent extraction of Mo and V with TOA (tri-n-octylamine) and precipitation stripping of V with ammonium salt at pH above 8.0. Regarding grinding conditions of alkaline leaching residue for selective Ni leaching against Al, it was found that Ni leaching efficiencies increased by providing higher grinding intensity, while the Al leaching efficiency increased and then decreased with increasing grinding intensity.INTRODUCTIONHydrodesulphurisation (HDS) catalysts account for about one third of the total worldwide catalyst consumption and are extensively used for sulphur removal in petroleum refineries (Zeng & Cheng, 2009). Fresh HDS catalysts generally contain molybdenum (Mo) and nickel (Ni) on an alumina carrier, but various elements included in the crude oil such as sulphur, carbon, silica, arsenic, cobalt, and vanadium (V) deactivates HDS catalysts during HDS reactions. As a result, spent HDS catalysts contain high concentration of rare metals. For example, regarding to Mo and V, it has been reported in the literature that the concentrations of Mo and V in the general spend HDS catalysts are generally 10-30% and 1-12%, respectively (Zeng & Cheng, 2009), which makes it economically viable to recover these rare metals (Biswas et al., 1986).Among a number of processes proposed for the recycling of rare metals from spent HDS catalysts, alkaline leaching is often used for selective Mo and V leaching (Zeng & Cheng, 2009). However, the process which provides a high degree of separation between Mo and V from a leaching solution had not been developed. Therefore, the first objective of this study was set to develop a solvent extraction-precipitation stripping process for the separation of Mo and V from solutions. More specifically, using artificial aqueous solutions of Mo and V, a series of experiments was performed to optimize the extraction pH, stripping agent, and the stripping pH."

Jan 1, 2016

In the last 30 years numerous mining plants have been developed in North America but only a handful of these have required freezing the area where the shaft was sunk. The most recent mine shaft to be sunk using this technique is located on an island off the coast of Louisiana. The project required the input and skills of numerous people in several companies, including the owner, engineers and contractors. The Cote Blanche installation is one of several mines in the area which extract salt from a dome which extends under the Gulf of Mexico. The geology of this area is, however, markedly different from others in the region because there is approximately 460 ft of water logged soil above the salt dome. Because it is not possible to sink a shaft in ground that is this soft, the overburden where the shaft is located must be frozen before excavation can take place. The Cote Blanche mine is a producing facility which was built in 1958 by the Carey Salt Company. The original facility included a 14 ft diameter production shaft and a 7 ft-8 in diameter service/ventilation/escape shaft. This system was installed by The Cementation Company. In 1996 the owner decided to improve both the mine ventilation and production hoisting system by installing a third shaft. This shaft would be designed to extract 650 tons per hour from a depth of 1600 ft and provide 500,000 cfm of ventilation to the mine at a maxium design pressure of 4 in WG. These parameters resulted in a requirement for a 16 ft finished inside diameter concrete lined shaft and a headframe designed as a pressure bulkhead. Because the mine would operate from one level only, the most efficient hoisting system for the application was determined to be a ground mounted koepe running on rope guides. With these criteria fixed Cote Blanche embarked on a program which would see construction start in June 1998 with the first salt produced in February 2001 at a cost of $US18M. The major players in the design and construction were G.L. Tiley & Associates Ltd., BLM Bharti Engineering, Freezewall Inc., Phillips Mining, Geotechnical and Grouting Inc., Don Hart Consulting and Dynatec International.

May 1, 2002

By Virginia Lawson, Adam Price

The rougher flotation stage is used to reject liberated gangue at a coarse size. Base and precious metals due to their high specific gravity tend to recycle in the grinding circuit and report to the flotation circuit at a finer size than the gangue from which it is being separated. Generally liberation levels of greater than 50% are achieved in roughing and thus a portion of the feed can be immediately upgraded to final concentrate. The proportion increasing as the amount of liberated mineral in the feed increases. Scalping out concentrate from the rougher can reduce the size of the subsequent regrind and cleaner circuits. Examples of alternative process design for circuits demonstrates that you don’t need large volumes to effectively recover all of the minerals – you need smart flotation. Several case studies will be presented where circuits can be significantly reduced in size by designing smarter – not larger. This paper describes case studies to test the amenability of the Jameson Cell to produce final concentrate from rougher feed. Metallurgical performance and plant design implications are discussed. Froth flotation has been used extensively for mineral concentration for over 100 years. Although the flotation cell design has changed, it has generally simply increased in capacity rather than increase in efficiency. Cell capacities of over 600 m3 are now being used in rougher flotation particularly for the lower grade ores where the amount of surface area for flotation is deemed less significant than the required volume. The plant design volume in rougher flotation comes from laboratory batch flotation tests and/or pilot plants. The volume required for the plant is calculated based on the laboratory residence time multiplied by a scale- up factor. Examples of laboratory to plant scale-up design are given in Dunne et al. (2010 part 2). The factors are usually between 2 and 3. A laboratory residence time of 10 minutes would equate to a plant design residence time of 25 minutes using a 2.5 factor. The volume of the required flotation cells can then be calculated using the design tonnage and volumetric throughput. This scale-up factor takes into account the differences in performance between batch flotation efficiency and full scale plant. The differences are likely related to inefficiencies of bubble particle contact in large cells as well as froth recovery, which is essentially complete in a batch cell. Flotation cells, such as the Jameson Cells, are smarter designs that improve bubble/particle collection, bubble/pulp separation efficiency and operate with high froth recovery rather than simply getting bigger. The Jameson Cell was designed on the principal of improving the collection efficiency of fine particles by separating the contact zone from the separation zone and having the bubbles generated by the plunging jet shearing and entraining air. This means the method of bubble generation is not impacted by the wear of mechanical equipment as it the case in other flotation devices. Jameson Cells make bubbles less than 600 micron in size under most operating conditions (Ding, 2016).

Jan 1, 2019

By P. J. Poirier, J. A. Meech, H. Raabe

"An Expert System has been implemented to assist operators in applying knowledge about froth conditions in the control of the flotation circuit at Highland Valley Copper. For some time, the personnel at Highland Valley Copper have recognized that froth type is a useful indicator of good operating conditions. However, the operating strategy based on froth type recognition is an ad-hoc skill in which different operators use a variety of terms, features and procedures to identify and solve problems. The first phase of this project developed an on-line consultative system to advise and tutor so that the diffuse expertise could be rationalized and consolidated into a standardized format.The second phase has brought this knowledge into a real-time environment to advise the operators on the floor in identifying froth types and troubleshooting corrective action. This paper describes the steps taken to acquire the knowledge, to design the required system features and to implement the real-time version of this system.INTRODUCTIONThe use of expert systems in the mineral industry has been gaining popularity in recent years. Minnova Inc, Les Mines Selbaie, Wabush Mines, Potash Corporation of Saskatchewan are just a few examples of Canadian mining companies that use expert systems to monitor or control their plants. Applications in the field of flotation include Brenda Mines (Edwards, 1992), Mt Isa Mines Ltd (Lacouture et al, 1991), Outokumpu (Karhu, 1989) and Kidd Creek (Burrows et al., 1989).Expert systems are defined as ""computer systems that apply reasoning methodologies on knowledge in a specific domain in order to render advice or recommendations much like a human expert"" (Turban, 1988). The main areas of application are diagnosis, training, process monitoring and control, and design. There are basically two main types of expert systems: Consultative systems, which are off-line applications in diagnosis and design, and on-line realtime systems, used for supervisory process control and real-time advising."

Jan 1, 1993

By J. Mizera, B. Adamczyk-Cieslak, K. J. Kurzydlowski, A. Dobkowska

"AZ31 is the one of the most popular magnesium alloy using in the modern industry. It is well known, that compared with steel, magnesium alloys posse better properties, such as light mass, high specific strength or thermal conductivity. It should be noted that their application is limited by poor corrosion resistance. In this work the corrosion behavior of AZ31 magnesium alloy as cast and after heat treatment were described with the use of testing in neutral salt spray atmosphere.To characterise corrosion resistance and describe layers built on the surface it was necessary to do the metallographic observations with the use of optical microscopy. After that influence of heat treatment for AZ31 corrosion resistance was examined. Measurements were conducted by electrochemical impedance spectroscopy (EIS) and by neutral salt spray tests in artificial atmosphere. Surface and cross section morphology after removal of corrosion products were observed with the use of scanning electron microscopy (SEM).The weight loss measurements show that there is no significant difference between alloys as cast and with following heat treatment.INTRODUCTIONMagnesium and magnesium alloys are popular in modern industry because of the low density and good formability. Magnesium alloys are described by few properties which have got significant influence for their application in transportation and electronics industries (Feliu & Liorente, 2015). Their wide application is limited by poor corrosion resistance. As it is well known Mg is one of the chemically most active metal. Corrosion resistance of Mg alloys depends on several factors, such as impurities, chemical composition or working conditions (Cheng, Qin, Wang, & Zhang, 2009). That all causes that there are many different ways to find well defined and good solution of magnesium alloys processing to improve their corrosion resistance.There are many different versions about the influence of aluminum on the corrosion resistance of magnesium alloy. It is known that intermetallic compounds such as Mg17Al12 due to ß-phase content plays the minor role for corrosion resistance. It is proved ß-phase acts as cathode and it has good ability to build passive layer in broad pH ranges. However it should be noted that mentioned behavior depend on size and distributions of ß-phase in the microstructure (Singh, Singh, & Das, 2015)."

Jan 1, 2016

By C. B. Webber, L. S. Diaz

"The paper presents the approach taken by Craigmont Mines to grinding circuit control. A detailed description is given of a fully automatic control system which bases its control actions on the continuous measurement of particle size in the cyclone overflow stream. The control system holds a specified particle size in the cyclone overflow, and grinds rod mi 11 ore feed at increased rates. The principles of operation of the system used for continuous measurement of particle size are described, end the improvements in mill throughput and copper recovery over several months of continuous operation are presented.INTRODUCTION Craigmont Mines Limited is located in the south-western interior region of the province of British Columbia, approximately 230 road miles north-east of Vancouver, and ten miles west of the town of Merritt. A moderate climate, good roads and service facilities provided by the Canadian Pacific Railway, Inland Natural Gas Company, and the B.C. Hydro and Power Authority, have provided a very favorable mine and plant site.The preliminary metallurgical design of the Craigmont mill was based on the test results of samples obtained from the original 2500' level drift during 1959. Pilot plant runs and other research testing for design pur¬poses were conducted at the Canadian Exploration Ltd. Laboratory, at Salmo, B.C. The design flowsheet was altered in progressive stages from 2,000 to 3,000, and finally 4,000 tons per day as the ore reserves became better defined. Construction work on the 2,400' level mill site commenced in late 1960. The official opening of Craigntnt Mines Limited took place on September 15, 1961, a little over two years from the time of the metallurgical assessment of the original ore samples.Mill throughput to date has varied widely both on a daily and a monthly basis, due to the varying hardness of the mine ores. The grindability af the ore appears to be related to the oxide iron content, which varies from lows of 9% to highs of 20%. Daily tonnage has ranged from 5,000 tons per day with 10% iron in the feed, to 6,000 tons per day with 20% iron feeds."

Jan 1, 1973

By Shantanu Patel, C. Derek Martin

"The objective of this work is to develop a practical numerical approach for applying the confining pressure to discrete element cylindrical triaxial tests. A layer of membrane particles with very low stiffness and extremely high contact bond strength was created around the lateral boundary of the cylindrical numerical specimen. To prevent the membrane particles from penetrating into the rock specimen on application of confining forces and to provide a smooth boundary surface, the space between the membrane and rock particles was filled using small-diameter packing particles. The results of this method were compared with those of rigid boundary method with confining pressure of 20MPa. The results obtained show that new approach gives both peak strength and post peak response that are in closer agreement with laboratory findings. BACKGROUNDThe discrete element method (DEM) has become the cornerstone for simulating both intact material and discrete fractures for low porosity strong rocks (ISRM Classes R3 to R6). Despite the advances in its application, simulating realistic behaviour of intact rock using the DEM remains a challenge. The bonded particle model was introduced as a potential solution for simulating the complex mineral grains in strong rock and other granular materials (Potyondy and Cundall, 2004; Utili and Nova, 2008; Salot et al., 2009). While some issues were resolved, a remaining challenge is the lack of the bonded particle model to simulate the brittle response commonly observed in strong rocks during the triaxial compressive test. Such behaviour is shown in Fig. 1 for Lac du Bonnet Granite at a confining pressure of 20MPa."

Jan 1, 2015