Search Documents

By A. Abadías Llamas, N. Bartie, M. Stelter

Evaluating the economic viability as well as the sustainability of the Circular Economy (CE) system requires a deep understanding of the distribution of all elements, compounds, alloys, materials etc. in flows. In this paper, the circularity of the copper value chain, including primary and secondary processing, is rigorously evaluated. The studied system comprises the metallic copper production from primary sources (from mineral to metal), copper-containing commodity production (copper is mixed with other metals) and copper recycling through secondary smelting to close the loop. This is linked to photovoltaic (PV) panels and battery storage. A simulation model of this system is created using HSC Sim, considering more than 30 elements (and its various compounds), 180 unit operations and 800 flows. From the mass and energy balances obtained through the simulation, an exergy analysis is conducted to evaluate the resource consumption from a second law (entropy) perspective. Additionally, these results are complemented through a Life Cycle Assessment (LCA), the recovery of technology elements and by-products is discussed, while quantifying the losses through the value chain. Through the digitalization of the complete system, a better CAPEX and OPEX understanding of the metal recovery and losses can be obtained, as well as the associated resource consumption and environmental impacts. New flowsheets and technologies can be evaluated. Several scenarios show how the resource consumption and the environmental impacts are affected by the recovery of different materials to produce different products. INTRODUCTION A key challenge of the circular economy (CE) is the linkage and optimization of both resource and energy efficiency of the (renewable) energy infrastructure and the resource cycle depicted by Figure 1 simultaneously. In addition, the CE requires the linkage of all stakeholders as shown by Figure 1. This has been discussed in some detail by Reuter and Bartie (2019) and Reuter et al. (2019). Copper and all its associated technology elements is one of the key enabling metals that is an economical copper colored thread through CE society (Reuter & Kojo, 2014). The Metal Wheel (Figure 2) shows the linkage of and recovery of various elements associated with copper and other carrier metals. This reveals that copper acts as an important carrier metal because of its properties i.e. the wealth of technology elements it carries from geological ores, but also its capacity to act as solvent of valuable elements and thence a key closer of various complexly connected element and material cycles when these technology elements are released during copper refining. The same applies to all other carrier metals of modern CE society as shown for example recently in a lead policy brief (Blanpain, Reuter & Malfliet, 2019).

Jan 1, 2019

By S. Yano, S. Takagi, Y. Nagaya, T. Akai, T. Ishida, Z. Bennour, T. Suzuki

"It is often reported that the concept of single-plane-fracture is not sufficient to account for the productivity from shale gas/oil wells. Many researchers introduce the concept of the stimulated reservoir volume to describe observed production behaviour. However, the characteristics of the stimulated reservoir volume are not well understood. In this study, to investigate the characteristics of fractures and surrounding region induced by the hydraulic fracturing, a devised hydraulic fracturing experiment was conducted using the cylindrical shale specimens in the laboratory.Two resins were prepared as the fracturing fluid for the experiments: cyanoacrylate, an instant glue, mixed with a fluorescent paint (resin A), and methyl metaacrylate, a thermosetting acrylic resin, mixed with a fluorescent paint (resin B). These resins were able to fix within the specimen after fracturing. This is because the present study aimed to only detect fractures induced by hydraulic fracturing. Cut sections of the specimens were observed under ultraviolet light irradiation. It is expected that the hydraulically induced fractures and the surrounding regions will be detected because the induced fractures filled with the resin should emit light, while the other parts will not.The specimens, which were collected from the Kushiro Coal Mine in Hokkaido, Japan at the depth around 275 m, were roughly 85 mm in diameter, 170 mm in length, and cored normal to the sedimentary planes. An injection hole with a 10-mm diameter was drilled onto the center of the specimen parallel to the sedimentary plane to simulate hydraulic fracturing in shale gas development. The experiment was conducted under a uniaxial loading condition of 3 MPa and the fracturing fluid was injected into the sealed injection hole at a constant flow rate using a syringe pump.After the fracturing experiment, the resins were fixed in the specimens and then the cut sections were observed under ultraviolet light irradiation. As a result, the hydraulically induced fractures, which were filled with the resin, are clearly observed. Detailed microscopic observations show that the main fractures are tortuous and are accompanied by many thinner ramified fractures. Additionally, fractured regions where the resin penetrates significantly are observed around the main fractures in the specimens fractured by the resin B. These induced fractures and fractured regions are considered to be the stimulated region in which permeability is improved. The necessity of estimation on the features of fracture tortuosity and ramified fractures is indicated for more accurate understanding of the well production and the stimulated reservoir volume."

Jan 1, 2015

By S. D. Normani

A Deep Geologic Repository (DGR) for Low and Intermediate Level radioactive waste has been proposed by Ontario Power Generation for the Bruce Nuclear site in Ontario, Canada. The DGR is to be constructed at a depth of about 680m below ground surface within the argillaceous Ordovician limestone of the Cobourg Formation. The objective of this paper is to apply paleoclimate boundary conditions to a regional-scale groundwater flow model for the DGR site and to describe the influence of glacial loading and unloading on flow system evolution using the FRAC3DVS-OPG flow and transport model. The regional-scale domain encompasses an area of 18,775km2 extending from Lake Huron to Georgian Bay in southwestern Ontario, Canada. From a hydrogeologic perspective, the domain can be subdivided into a shallow zone, an intermediate zone, and a deep zone comprised of the low-permeability units of Ordovician and the more permeable Cambrian where present. The deep groundwater zone is characterized by units containing stagnant water having high concentrations of total dissolved solids (TDS) that can exceed 300g=L. The high TDS values at depth require density-dependent coupled flow and transport calculations within FRAC3DVS-OPG. The computational sequence involves the calculation of steady-state density independent flow that is used as the initial condition for the determination of pseudo-equilibrium for a density-dependent flow system that has an initial TDS distribution. The 1,000,000 year pseudo-equilibrium heads and brine concentrations are used as the initial condition for the paleoclimate simulations. Over the past 900,000 years, the Canadian Shield has experienced approximately nine episodes of complete glaciation. During the glaciation cycles, the entire Canadian land mass has been covered by a series of continental ice-sheets whose maximum thickness reached 4 km and whose southern extents reached, in some cases, beyond the present-day Canada-U.S. border. The glaciation phase of a single glaciation-deglaciation episode is typically 90,000 years in duration, while the deglaciation portion proceeds relatively rapidly and has an average duration of approximately 10,000 years. Output from the University of Toronto Glacial Systems Model, a continental scale North American glacial reconstruction of the most recent 120,000 year glaciation event developed by W. R. Peltier, is used to supply the paleoclimate boundary conditions used in this paper. Permeabilty reductions due to the presence of permafrost are also considered in the paleoclimate simulations. This paper will demonstrate that the choice of rock properties can significantly affect residual pore water pressures within the rock matrix, as well as the migration of glacial meltwater.

May 1, 2009

By Gunther F. Leichtle, James A. Finch, Colin A. Hardie, Cesar O. Gomez

"The recycling of wastepaper has become an important and common process worldwide. Techniques similar to those used in the mineral processing industry are used to produce high quality recycled fibers for use in newsprint. The mineral processing group at McGill University in conjunction with the Pulp and Paper industry (Mechanical and Chemi-mechanical Wood Pulp Network) has adapted one of these techniques, column flotation, for the purpose of deinking wastepaper. This article describes the typical process of recycling wastepaper from a mineral processing point of view. It also presents results from McGill University's flotation column test work at a Quebec wastepaper recycling facility.IntroductionThe recycling of wastepaper has become an important and common process worldwide, including Canada which is now the world's largest importer of wastepaper (CPPA, 1996). Much of the current drive to increase the utilization rate of recovered paper is a reaction to the solid-waste disposal problem that faces many Canadian and U.S. municipalities. The real problem in the disposal of solid waste is not the absolute amount of garbage that must be disposed of each year but this amount in relation to available disposal capacity.Environmental restrictions on the creation of new landfill sites and incinerators (the two main options for disposal of municipal solid waste) have tightened the demand/supply balance in the solid waste disposal market. This shrinking availability of waste disposal sites in the face of increasing population with greater disposal requirements defines the Developed World's solid waste crisis. Not only are there fewer disposal sites available, but the costs of using them is skyrocketing. These factors have increased government regulations mandating recycled paper content in newsprint. Conservation and environmental issues make the current drive for wastepaper recycling a real issue and business opportunity.A key to the success of producing quality recycled fibers from wastepaper is the deinking technology. The production of tissue papers, paper towels and newsprint requires regenerated fibers which are substantially free of ink particles. Of the various options available, mineral processing techniques can offer the most economical, environmentally acceptable and versatile strategies (Yoon, 1993). Today, it is recognized that flotation is one of the most effective processes for removing ink particles in the production of a high quality product. In a collaborative program with the Pulp and Paper industry, the mineral processing group at McGill University has adapted column flotation technology for this purpose. This article will describe the typical process of deinking from a mineral processing point of view (Part A). It will also present some results from McGill University's flotation column test work at a nearby paper recycling facility (Part 8)."

Jan 1, 1998

By Nordau R. Goodman

T-he Ojibway Salt Mine near Windsor, Ontario, produces almost two million tonnes of97% pure rock salt annually. The salt is mined from the middle F horizon of the Silurian Salina Formation. The salt beds have a gentle dip into the Michigan depositional basin. There is no evidence of deformation. The rock salt is buff coloured and has a number of thin carbonateanhydrire bands. Secondary salt crysrallization occurs throughout the mine.

Jan 1, 1984

By Sebastian Siebert

Unmanned Aerial Vehicles (UAV) as a data acquisition platform and as a measurement instrument have become attractive for many surveying applications in civil engineering. However, their performance is not well understood for these particular applications. The specific scope of the presented work is the performance evaluation of a UAV system that was built to rapidly acquire mobile 3D mapping data for large earthmoving construction sites. Details to the components of the developed system (hardware and control software) are explained. A novel program for photogrammetric flight planning and its execution for the generation of 3D point clouds from digital mobile images is explained. A performance model for estimating the position error was developed and tested in several realistic construction environments. Results to these tests are presented as they relate in particular to large excavation and earth moving construction sites. Results and experiences with the developed UAV system are in particular useful for researchers or practitioners in need for successfully adapting UAV technology for their application(s).

Aug 1, 2013

By Yves Pépin, Sylvain Lefebvre, Dimitrios Filippou, Guillaume Hudon

"Titanium dioxide pigment plants using the so-called “chloride process” produce considerable amounts of chloride waste, which contains predominantly iron chloride. In most cases, this waste is dissolved in a weak hydrochloric acid solution and then neutralised. The metal content of the waste is dumped as hydroxide sludge, while its chloride content is lost in an effluent.Rio Tinto Iron & Titanium has developed a new proprietary process whereby pure metallic iron and chlorine gas are recovered from chloride waste by electrolysis. This process uses a two compartment cell separated by an anion exchange membrane to prevent iron cycling between its trivalent and divalent valence. The cathode is made of titanium Grade 7, while the anode is a dimensionally stable one of the type “metal–mixed metal oxide” (MMO) for the evolution of chlorine gas. The catholyte is concentrated and pH-adjusted iron-rich chloride solution originating from chloride waste. The anolyte is recirculating solution containing alkali or alkali earth chlorides such as MgCl2, NaCl, etc. Current efficiencies above 90% can be achieved at temperatures about 80°C using catholyte solutions almost saturated in iron chloride and other chlorides.In this paper, we discuss the details of this process, and how this could be integrated within a chloride pigment plant for the treatment of chloride wastes."

Jan 1, 2016

By V. Maazallahi, A. Rouleau, A. Saeidi

"The geometry of the terrain topography before and after the failure are the essential factors for analyzing a landslide and for the design of remedial works. This paper presents a method to determine these factors, considering that the determination of the slide surface profile is difficult and costly using traditional methods and the pre-slide topography data is often not available. The presented method to locate the 3-dimensional geometry of the slide surface is based upon determining the slide surface in 2- dimensional vertical sections. This method utilizes post-slide topography of the area to determine the pre-slide topography and uses equations to estimate the pre-slide situation using a statistical process applied to points located on the sliding mass. This method is tested on the Maskun landslide in Iran. The results indicate the applicability of the proposed method to obtain the key factors for the back analysis of a landslide in a cost effective manner.INTRODUCTIONProbably the most reliable method of determining the strength of soil and rock mass is to back analyze a failed or failing slope (Caia et al. 2007; Wyllie & Mah, 2004). This method is used in geotechnics for estimating geotechnical parameters of the rock and soil mass (Sakurai et al., 2003; Frayssines and Hantz, 2009; Cepuritis et al. 2010), but it requires that the failure mode is well established and that there is complete and precise information available on the slide surface and the sliding mass (Sjöberg, 1996). Measurement of the slope profile before failure provides the basic information required for a back analysis (Hock & Bray, 1981). The post-slide topography is another key factor. The back analysis process for determining the actual strength parameters of soil or a decomposed rock mass after a landslide requires knowledge of the sliding mass geometry, both before and after the sliding event. Many studies are reported in the literature about the application of back analysis for determining geotechnical and geomechanical parameters of rock and soil mass (Sakurai et al., 2003; Cepuritis et al. 2010; Frayssines and Hantz, 2009, Hussain and Stark, 2011), but they generally present little information about the geometry of the slide surface, and the weight of rock and soil mass that slid, although these factors are the most important parameters for back analysis process. Liang and Xue-song (2012) determined the slip surface having the minimum factor of safety (called critical slip surface in deterministic analysis of slopes) and the slip surface with the minimum reliability index (called critical reliability slip surface), but they have not considered the actual profile and geometry of the slide surface. Rocscience (2013) proposes the back analysis option in the Slide software for slope stability study, but it requires an imposed slide surface as input; alternatively, one can estimate by a finite element analysis the surface with the minimum factor of safety. However, this estimated surface is very likely different from the actual sliding surface, considering the uncertainties in input data of the finite element method."

Jan 1, 2015

By A. A. Lavrinenko, N. I. Gluhova, L. M. Sarkisova, D. V. Makarov

"The investigated sulfide Cu-Ni ores are characterized by low PGE contents and emulgated impregnations of pentlandite and palladium minerals in the main ore-forming mineral pyrrhotite, which hinders their selective separation, requiring a collective flotation of sulfides to concentrate, and hydrometallurgical processing. As revealed by studies of floatability of Pt-Cu-Ni ore in a mixture of butyl xanthate and chelating phosphorus containing reagents, the most effective additive is Aerophine 3416 (a phosphinates mixture) manufactured by Cytec. Using collective flotation with a butyl xanthate – Aerophine 3416 composite in the ratio of 1:3 has afforded to enhance the Pt, Pd, and Ni recovery by 13.6 %, 9.2 %, and 9.4 %, respectively. The optimal ratios of Aerophine 3416 to butyl collector for the collective flotation are the following: 1:1 for Pt and Pd and 3:1 for Ni. The effect of these reagents on the electrode potential and surface hydrophobicity of pyrrhotite, pentlandite, and platinum black has been investigated. The extraction UV spectrophotometry experiments demonstrate that DIBDTPI exists on the pyrrhotite surface mainly in the form of disulfide in weak acid medium and in the form of compounds with Fe on the mineral surface in minute amounts. There appears some disulfide and few amount of (DIBDTPI)2Ni on the surface after interaction of DIBDTPI and pentlanditeINTRODUCTIONXanthates are widely used in flotation of copper-nickel ores containing platinum group metals (PGM) as sulfides collectors which can concentrate the most part of PGM connected with the sulfides. Though xanthates are hardly efficient for flotation of free PGM, the latter are floated more slowly compared to the sulfides of base metals. The reasons for poor floatation of free (mineral) forms of PGM are under-researched, however the key accepted reasons are: fine disseminations of free PGM, insufficient interaction with xanthate and negative influence of blue copperas and sulfur-containing ions which are sulfides oxidation products (Penberthy et al. 1999; Shackleton et al., 2007). That’s why an additional collector, normally dialkyldithiophosphates, is used during flotation of PGM-containing copper-nickel ores. A reagent DP-4 is used for recovery of PGM at Norilsk mining and metallurgical plant. The reagent represents a slightly-soluble organic calcium sulfonate which is given to flotation pulp in the form of water emulsion of 5% - solution in automotive diesel oil."

Jan 1, 2016

By S. Papanakli, Th. Rondoyanni, N. Sabatakakis, K. Kavoura, G. Tsiambaos

"A representative composite fault-related landslide of the Corinth Gulf graben named “Panagopoula” is reported that considered to be one of the most prone to slope instability sites along the main motorway and railway connecting Athens with the city of Patras. The presence of tectonically highly sheared and weathered geological formations, including Alpine basement (mainly flysch) contributes to the site instability, triggered/reactivated by seismic activity and heavy rainfalls. Although a series of remedial measures have been already constructed, the inclinometer readings during the last twenty years time period show a continuous very slow movement which indicates that the landslide is still ""active"". This fact has resulted to divert the axes of the new motorway and railway through twin tunnels which are under construction. INTRODUCTIONThe spatial and temporal evolution of landslides in the case of structurally complex slopes is lithologically and often structurally controlled while their type and frequency are mainly related to tectonic and lithological anisotropy (Baron et al. 2005; Hradecky et al. 2007). The triggering mechanisms mainly include: (a) excessive rainfall generating high pore pressure and (b) strong earthquakes resulting in dynamic loading conditions at the failure surface. Data such as past earthquakes or the precipitation records are useful to be gathered when a landslide model is examined since they could act as a landslide triggering mechanism. Recording of the movement through surface and inclinometer measurements as well as combination of the above information with historical records of failure could lead to a more accurate estimation of the location of the failure surface and understanding of the landslide mechanism.Slope instability in the southern segment of the Gulf of Corinth, Northern Peloponnesus, Greece, is ubiquitous and ranges from deep-seated bedrock failure to secondary earth flows in recent deposits. In this part of Greece, the periodically induced landslide events triggered by heavy rainfall, earthquake and anthropogenic activity are closely related to active fault tectonics. The Gulf of Corinth is considered as a typical example of a relatively simple asymmetric half-graben with major border faults to the south and a flexure of the northern shore. Panagopoula landslide is located along the trace of a WNW trending normal fault (dipping northwards) (Figure 1). The area is considered to be one of those most prone to slope instability along the E95 motorway and railway connecting Athens with the city of Patras."

Jan 1, 2015

By Masashige Makifuchi, Hiroki Kumakura, Kota Nagai, Takahiro Kikuchi

"A large amount of platinum group metals (PGM) are used in automobile catalyst. It is important to recover the metals from wasted catalyst. Nomura and Kageyama (2013) suggested recovery process that PGM oxides were absorbed to perovskite-type oxide based on LaScO3. In their process, the PGM in wasted catalyst as absorbed to the perovskite-type oxide as PGM oxide. It has potential to each element in the process if the perovskite-type oxide is selected properly. In this study, the PGM oxide absorption properties of various perovskite-type oxides are investigated to develop a new recovery and separation process. The various perovskite-type oxide were synthesized with metallic platinum, palladium, rhodium at high temperature in air atmosphere. And the PGM contents in the perovskite-type oxide after the experiment are determined by chemical analysis. Some of them have the properties to absorb specific PGM oxide selectively. In addition, in order to increase the amount of absorption of PGM oxide and composition of the perovskite-type oxide experimental temperature was investigated. Then it is also found that doping another specific element to the perovskite-type oxide is effective to increase the amount of absorption of PGM oxide. Then a new recovery process of PGM from wasted automobile catalyst, in which PGM can be separate to each element, was designed.INTRODUCTIONA large amount of Platinum (Pt), Palladium (Pd), and Rhodium (Rh) are used in automobile catalysis (Figure 1) (Platinum, 2013). Natural supplies for these metals are limited and PGM mining can detrimental environmental impact. Therefore, the recycling of PGMs from wasted automobile catalysis is very important. The Rose process (Figure 2) was developed as a process to recover PGM from wasted automobile catalysis. In this process, the automobile catalysis is first crushed mechanically, and then extracting agent, copper (Cu), and flux are melted at high temperature. The mixture separates into a metal phase, (Cu alloy containing PGM) and slag. The PGM is enriched by oxidizing. Cu to Cu oxide. The PGM are then recovered and separated to each element in a wet process. However, it is hard to dissolve the PGM with acid because they are chemically stable and strong oxidation agent such as aqua regia is used. Moreover, to separate the PGM to each individual element, a solvent extraction process is required."

Jan 1, 2016

By H. K. Olsen, B. Thomassen, H. K. Schønwandt, L. Grahl-Madsen, H. Stendal

Abstract-The central part of the early Proterozoic Ketilidian orogen in South Greenland consists of an I-type granitoid batholith transected by four regional NE-SW-trending shear zones. The batholith was probably emplaced during subduction, from the south toward the Archaean craton in the north, in a sinistral transpressional system. A regional sediment sampling program covering 5000 km2 shows a close connection between a gold-mineralized trend and one of the major shear zones within the epizonal facies of the batholith. The gold mineralization is not directly related to the major shear zones, but occurs in quartz-veined and silicified second-order structures. High-grade (up to 114 ppm Au over 6 m) low-tonnage mineralization is found within these second-order structures cutting both amphibolites and granitoids. The mineralization is characterized by negligible or small alteration halos. Gold is associated with various element combinations of enhanced As-Bi-W- Cu, which indicate that the mineralization is mesothermal in origin.

Jan 1, 1995

By H. K. Olsen, B. Thomassen, H. K. Schønwandt, L. Grahl-Madsen, H. Stendal

The central part of the early Proterozoic Ketilidian orogen in South Greenland consists of an I-type granitoid batholith transected by four regional NE-SW-trending shear zones. Thebatholith was probably emplaced during subduction, from the south toward the Archaean craton in the north, in a sinistral transpressional system. A regional sediment sampling program covering5000km2shows a close connection between a gold-mineralized trend and one of the major shearzones within the epizonal facies of the batholith. The gold mineralization is not directly related to the major shear zones, but occurs in quartz-veined and silicified second-order structures. High-grade(up to 114 ppm Au over 6 m) low-tonnage mineralization is found within these second-order structures cutting both amphibolites and granitoids. The mineralization is characterized by negligible or small alteration halos. Gold is associated with various element combinations of enhanced As-Bi-W-Cu, which indicate that the mineralization is mesothermal in origin.

Jan 1, 1995

By P. K. Kaiser, F. Amann

"Rock mass characterization for deep underground construction and mining offers many challenges. This paper first describes some of the key challenges when characterizing highly stressed brittle rocks and then offers some guidance on how to arrive at reliable rock mass strength parameters for deep mining applications. Focus is placed on characterization for rock mass strength determination. It is illustrated how the common use of currently available rock mass characterization systems tend to underestimate the strength of rock at depth. Modifications to currently adopted approaches, i.e., the use of Geological Strength Index GSI for rock mass strength determination, are presented.INTRODUCTIONFor green fields projects, the first challenge of rock mass characterization stems from a lack of access to examine the rock mass at scales larger than typical core sizes (i.e., ~63mm in diameter) until late in the mine design when the flexibility for making changes is constrained. Hence, rock mass characterization often has to rely on information derived from boreholes alone (e.g., core, logs, etc.). This challenge is lessened when mines are expanded from existing operations. A second challenge is related to changing rock mass behaviour with increasing depth and stress. At depth, the rock is highly stressed, thus closer to failure, and often highly confined which leads to a higher interlocking with elevated strength but more brittleness. The goals of rock mass characterization are to be tailored to the technical goals of an investigation. For example, for cave engineering, the workflow includes the assessment of five key engineering aspects (Brown, 2007): Caveability; fragmentation; cave performance; extraction level stability; and mine construction (rock support). Each engineering aspect has to address specific engineering questions and each design component is influenced by different rock mass behaviour aspects and thus is dominated by different rock mass properties, e.g., the vulnerability to stress fracturing (spalling), the bulking characteristics for flow control and support selection, and the confining stress impact on pillar or support design. An effective rock mass characterization program, including logging, mapping and laboratory testing, thus has to collect and interpret features that are relevant for the above listed purposes. Some of the predominant factors are: block volume of defected and non-defected rock; spalling strength; tensile strength of defects; rock mass modulus; and rock mass strength parameters for application to low and high confinement design aspects."

Jan 1, 2015

By V. Schenk

Dust exposure resulting from the exploitation and winning of natural resources below ground has presented a serious health problem since the beginning of mining. The boom phase of the German hard coal mining industry after World War II with at times up to 500,000 employees saw an increase of dust exposure of miners below ground as the mechanization of road heading and mining increased significantly. More and more miners were diagnosed with coal-workers-pneumoconiosis (CWP), a chronic and irreversible lung disease resulting in a significant impairment of pulmonary function. This realization led to a reduction of CWP in the German hard coal mining industry in the 1960s. The successful fight against CWP began with the introduction of technical dust prevention measures. By infusing the coal seam with water before mining, sprinkling and spraying of heading and mining machines as well as canopies with water, aspiration in places with high amounts of dust and the suppression of dust with chemical substances it is possible to significantly reduce the miners? dust exposure. All operating points below ground are checked and measured regularly with regard to dust exposure. Through the combination of these values together with the individual shift data a relatively precise profile of individual dust exposure can be obtained. This profile allows the targeted work assignment when certain predetermined limits have been reached, moving the miner to a work place with less dust exposure and thus reducing the chronic dust exposure. The state of health of the individual is known because since about 60 years ago extensive occupational health checks have been carried out regularly at least every two years which means that work restrictions can be imposed depending on the findings. Since the beginning of the 1980s more value has been attached to not only situational but also behavioral prevention. Given the comprehensive provision of protective masks, having a protective effect as well as the required comfort when being worn, each miner has the opportunity to protect his respiratory organs depending on the specific dust exposure. Through a combination of all these measures the German hard coal mining industry has succeeded in beating the classic coal miner?s disease CWP. For mines in the Ruhr valley this means that a miner who started work after 1978 will no longer develop CWP.

Aug 1, 2013

By C. Zangerl, T. Strauhal, S. Perzlmeier, M. Holzmann

"In high mountainous regions, deep-seated rock slides are often observed in foliated metamorphic rocks such as paragneisses, micaschists and phyllites. Given that comprehensive investigations of deepseated rock slides are extraordinary costly and therefore are rare, most studies are related to investigations in the surroundings of infrastructures and human settlements. In the framework of this study there is an excellent opportunity to gain new insights in the fundamental processes and mechanisms of slowly moving deep-seated rock slides from a case study in the surrounding of a large dam reservoir in Austria. New fundamentals for comprehensive slope stability analyses and hazard assessments and sound prognoses focussing on the long-term stability and deformation behaviour of slopes under changing boundary conditions (e.g. impounding of a reservoir) and/or concepts for mitigation measures can be obtained. Within this contribution, geological field surveys, deformation monitoring, geophysical and drilling data were analysed and presented. Based on the compiled and analysed data, some key-properties of the rock slide will be presented, whereby special attention will be given on the geometry and internal structure, the slope kinematics, as well as hydrogeological and geomechanical aspects.INTRODUCTIONIn high mountainous regions, deep-seated rock slides are often encountered in highly foliated metamorphic rocks such as paragneisses, micaschists and phyllites (Agliardi et al. 2012). Critical situations may occur when deep-seated rock slides fail in a rapid manner characterised by very high sliding velocities, and/or when they develop into long run-out rock avalanches. However, many rock slides in foliated crystalline rock masses either do not move at high velocities nor do they accelerate seriously and form extremely rapid slides. Displacement rates in the range of a few millimetres or centimetres per year are common for this type of rock slide (Bonzanigo et al. 2007, Tentschert 1998, Watson et al. 2007). Nevertheless, some case studies show an activity behaviour characterised by acceleration phases reaching velocities of even metres per day. However a slope collapse is not expected and these slopes decelerate to much lower base activities. The trigger for these phases can be manifold and include heavy rainfall and snow melt, initial reservoir impounding and water level fluctuations, changes in the slope’s equilibrium state due to antecedent slow deformation processes, ongoing erosion processes along the toe of the slope, and others (Zangerl et al. 2010)."

Jan 1, 2015

By Silvio E. Kruger

Real time measurement of wear and corrosion provides crucial information needed to determine an optimal schedule for corrective maintenance and is a powerful tool to maximise equipment availability and reliability. It also leads to savings from optimized spare parts handling and helps to avoid costs of accidents and their negative impact on safety and the environment. This paper presents the technology of ?painted-on? ultrasonic transducers that can be integrated to structures and accurately measure the remaining thickness and therefore determine wear or corrosion losses. These transducers have a small footprint, a performance comparable to other commercially available ultrasonic transducers and can sustain temperatures as high as 400ºC. The application of this technology to mining equipments and its potential benefits are discussed.

Aug 1, 2013

By K. Thuro, S. Schneider, H. Kasling, P. Ellecosta

"One of the most important methods for material testing is the characterization of the hardness, which is defined as the resistance of a material to the penetration of another one. The methods according to Brinell, Vickers, Rockwell and Knoop are today the most common and standardized tests for metal. As they are developed for predominantly ductile materials like steel, they can’t easily be applied to rocks which react much more brittle under indentation. But just as steel, rock is composed of different minerals and has a specific microstructure. Its mechanical parameters are connected with the particular grains, their cohesion and interlocking, just like steel.The abrasivity of rocks and the accompanied wear of drilling tools today are mainly determined by simple and fast laboratory tests such as the Cerchar abrasivity test or the rubber wheel test. Such laboratory tests are good tribological tests, but there are limits. The Cerchar abrasivity test for example has weaknesses in extreme cases, that mean soft or very hard rock types. This leads to an underestimation of abrasivity, e.g. in poorly lithified sandstones or very hard, fine grained and extremely abrasive rocks. As mentioned, hardness characterizes, depending on the type of deformation, predominantly plastic (metal) or elastic properties (rubber). Rocks are in the range between these two extremes. Since the rock drilling process can be seen as a kind of penetration process on macroscopic and microscopic scales, we picked up the idea to characterize the interaction of rock materials and TBM-disc-cutters with hardness tests. In addition, this supports for a better understanding of the wear process on disc cutters. We used the hardnessdisparity concept after Cardu & Giraudi (2012) because wear can be understood as the interaction between the wear part and the material which causes the wear (tribological system). Several rock-forming minerals and some fine to coarse-grained monomineralic and polymineralic rocks were tested. In contrast to Cardu & Giraudi, we used in the first step of investigations the method after Vickers with loads up to 294.2 N (HV 30), depending on the estimated hardness to get bigger indentations and therefore as well information about the cohesion and interlocking of the minerals/grains. We also tested several associated disc cutters. First results show that with higher loads (HV 5 - 30) and at least 15 indentations, we get a structural hardness in fine-grained rock samples, which allows a good characterization of the elasticity and brittleness. Nevertheless, for the coarse-grained rock samples we need up to 40 indentations for a good characterization. Using this method, a prediction of disc cutter wear is feasible taking into account the hardness of the disc cutter steel. In this paper, we would like to present this approved method in material sciences to derive an additional parameter for the characterization of rock abrasivity and wear."

Jan 1, 2015

This paper generalizes open stopes into elliptical cross sections and applies the results of calculations based on the mathematical theory of elasticity to indicate stress distribution on the boundaries of such stopes. These show both compressive and tensile stresses and provide an ex-planation for the development of excessive dilution in shrinkage toping. Introduction T HE stress pattern around shrinkage stopes is identical with that around other stopes under the same physical conditions. However, a shrinkage stope ends as an unsupported open stope, and the method i limited to the stress range within which the rock is generally self-supporting. If it is acceptable to generalize the outline of a shrinkage stope into an elliptical cross section, then the graphs of Geldart & Udd (1) (see also Panek (2) and Denkhaus (3)) provide a good base for approximating the stress distribution as mining progresses. However, with failure conditions in the walls, the axis ratio, as cut

Jan 1, 1964

By R. K. Kandasami

"Naturally occurring geomaterials such as sandstone, limestone and other soft rocks, residual soils are composed of a particulates held together through a cohesive matrix, usually composed of argillaceous or siliceous cementing agents. Geo-materials such as these have been reconstituted in the laboratory using ordinary Portland cement in lieu of the naturally occurring cohesive matrix, in addition to using sand particulates. This cohesive frictional granular ensemble is an ideal model material for understanding the mechanical behaviour of transitional geomaterials such as soft rocks. An important consequence of this cohesion that pervades the inter particulate system is the enhanced tensile strength when compared to a purely granular ensemble. The assessment of strength of these soft rocks and cemented sands is often understood in the framework of continuum mechanics, i.e. considering the cemented sand to be a continuum, and performing simple elemental tests such as uniaxial compression or tension tests. A simple model to describe the behaviour of these cemented sands has been to use elements such as springs, sliders, and dashpots in parallel to describe the existence of a cohesive and frictional component of strength (Jiang et al. 2007). In the framework of continuum mechanics, the mechanical response of these cemented sands have been modeled using traditional plasticity theory, for example utilizing variants of the traditional Mohr Coulomb model, Modified cam clay (Sun and Matsuoka 1999) etc. The typical sand models are amended to include the effects of cohesion, as proposed by Lagoia and Nova (1995).The mechanical response of cemented sands is understood to be transitional to the behaviour of a typical particulate assemblage and a quasi-brittle material. However, the effect of length scale in these material systems has not been investigated. This paper presents a series of uniaxial compression experiments conducted on weakly cemented sand specimens of various sizes. The effect of length scale in these weakly cemented sands is investigated through unconfined compression tests."

Jan 1, 2015