Search Documents

By A. F. Banks

"IntroductionThe typical potash processing plant recovers and/ or upgrades from 10% to 20% of its production through the recrystallization process. The feed to the recrystallization section consists of preconcentrated slurries of fine crystal size that cannot be raised to the required product grade by flotation and fine dusts also of low grade and too fine for compaction feed. It produces high grade white potash crystals that can be marketed as a high grade product or blended into the flotation products to raise their grade. In this chapter, a typical leaching (dissolving) and recrystallization operation will be discussed.The crystallization process makes use of the three phase system chemistry of NaCl, KCl, and H,O. The normal potash process operates on a temperature range of 75°F to 95 °F. A three phase slurry feed to the dissolving circuits will be within that range. The potash (KCl) is dissolved by heating the slurry in the presence of sufficient brine to a temperature of 190°F to 200°F. As the slurry is heated, the potash (KCI) dissolves and the salt (NaCI) precipitates. The potash rich brine is then clarified and the salt and other undissolved solids removed by thickening. Clarified brine becomes the crystallizer feed.The hot brine is cooled in evaporative cooling crystallizers. In cooling, the potash precipitates as a high grade white crystal. Crystallization is done in multiple effects to permit energy recovery and control of the process. In a four effect crystallizer the cooling is done by recycling mother liquor counter currently through the first two effect condensors and using brine pond brine for the cooling of the last two.The crystallizer product is removed from the last effect as a slurry at normal process temperature and is fed either to its own centrifuging and drying circuit or blended with the flotation product for centrifuging and drying."

Jan 1, 1989

By S. M. J. Mirazimi, F. Rashchi

Recovery of vanadium from LD (Linz-Donawits) converter slag was evaluated by means of microbial leaching. Vanadium leaching was performed in two stages. In the first stage, the bacteria were grown in a culture medium and in the second stage; vanadium containing slag was added to the metabolites produced by bacteria. Bioleaching was performed using heterotrophic bacteria Pseudomonas Putída. Control tests without bacteria inoculation were also performed and the results were compared with bioleaching outcomes. Optimal conditions for the bioleaching of vanadium containing slag were determined.

Jan 1, 2011

By M. Rafati

In this investigation, the effects of T4 and T6 heat treatments of AZ91 magnesium cast alloy have been studied. The effects of different microstructural details such as morphology, size and distribution of precipitates and their influence on fracture mechanisms were investigated by optical and scanning electron microscopy. The mechanical strength of the alloy after T6 treatment was found to increase in comparison to the T4 treatment, due to the formation of discontinuous precipitates in the grain boundaries. Precipitation in this alloy occurs in two ways: continuous precipitation, which nucleates and grows inside the grains, and discontinuous precipitation, which forms at the grain boundaries. During ageing, the length of the continuous precipitates increases, and, hence, interprecipitate distance decreases. The formation of discontinuous precipitates causes initiation and propagation of cracks at and the weakening of the grain boundaries. This is the principal reason for the reduction of the ultimate tensile strength in T6 heat treatment in comparison to the T4 condition.

Jan 1, 2006

By C. -K. Fang, T. H. Chuang

"Temperature effects on the erosion of the 6063 aluminum alloy were investigated. Erosion experiments were performed by sandblasting silicon carbide particles of 80 grit size. The target volume loss, and worn depths of the eroded material were investigated at different temperatures. It was found that the temperature had only a minor impact on the peak attack angle. The effect of temperature on erosion damage depended on the relative humidity (RH) of the environment. IntroductionThe synergy of wind and sand or dust may result in the erosion of materials. However, the severity of erosion damage in different areas and in different seasons might be varied, depending on environmental variables such as temperature and humidity. As a result, determining the effect of environmental variables on erosion damage is important in selecting or ranking materials for their suitable applications in diverse areas.The relationship between erosion wastage and temperature is governed by many factors including temperature dependent properties of the material (strength, ductility, toughness, and dynamic hardness, etc.), mechanical erosion characteristics, the rate of oxidation, and the mechanical properties of oxides. Although the effect of temperature on erosion has been studied for engineering materials (Smeltzer et al., 1970; Gat and Tabakoff, 1978; 1980; Levy et al., 1986; Levy and Man, 1986; Chinnadurai and Bahadur, 1995; Howard and Ball, 1997; Colclough and Yeomans, 1997; Suckling and Allen, 1997), published literature dealing with aluminum alloy is rather limited."

Jan 1, 2000

By Seher Ata

"Virtual reality, a three-dimensional computer generated environment, has become recognized delivery system for many forms of education. This article describes the application of virtual reality to mineral processing education. An interactive mineral processing visualisation module has been developed at University of New South Wales (UNSW), Australia. The module provides students with an overview of a base metal concentrator, details about each stage of the process, as well as revealing how the mined ore progresses from stage to stage. The module also involves developing a number of instructional based plant layouts and flowsheets in the virtual environment that are intended to assist the user in understanding the essential components of the base metal concentrator.INTRODUCTIONVirtual Reality (VR) is the creation of an artificial environment that is experienced through sights and sounds provided by a computer (Squelch, 2001). The simulated environment is achieved through a host of technologies such as three-dimensional graphics, audio feedback and special peripheral devices to produce interactive environments.VR has been used in diverse fields including medicine (Riener & Harders, 2012), entertainment (Hsu, 2011), military (Manojlovich, Prasithsangaree, Hughes, Chen, & Lewis, 2003), manufacturing (Zimmermann, 2008; Jiang, 2011), and chemical processing (Schofield, Lester, & Wilson 2005; Squires, Andersen, Reklaitis, Jayakumar, & Carmichael, 2014). VR is also becoming recognized delivery system for many forms of education, including engineering education (Bell & Fogler, 1996; Bell & Scott, 1998; Shin, 2002). For example, virtual laboratories have been designed and developed to teach students fundemental features of the heterogeneous catalytic mechanisms and absorption columns (Bell & Fogler, 1995), the multi-phase and multi-component blast furnace iron making process (Babich & Senk, 2009) and to guide students to identify various safety measures while working in real laboratory (Bell & Fogler, 1996)."

Jan 1, 2016

By W. L. Stuewe

The Dominion Steel and Coal Corporation requires enormous quantities of bricks each year for its Sydney steel plant operations. Clay brick of all types are purchased, while silica brick is made in the Company's plant at Sydney. A description of this plant was given in a paper presented by H. B. Gillis and F. C. Morrison at the 1938 Annual General Meeting of the Institute. The rock used to make silica brick was for years obtained from a quarry at Leitches Creek, about eighteen miles from Sydney. Due to the gradual deterioration of this deposit, the Corporation was forced to look for other sources of supply. In 1945, the problem was presented to the Nova Scotia Department of Mines and, through the efforts of Dr. A. E. Cameron and Mr. J. P. Messervey, an examination was made of a silica-rock deposit some six miles northwest of Yarmouth, N.S. Preliminary samples proved satisfactory, and arrangements were made with the Department of Mines to ship to the steel plant at Sydney a fifty-ton car load for the purpose of further testing. Brick made from this sample shipment stood up very well in the furnaces. At the same time, two hundred and fifty tons of silica rock from a deposit at Lac Bouchette, Que., were purchased from the Industrial Silica Corporation, and brick made from this rock also was found suitable for our requirements. Comparative transportation costs, however, led to a decision to open the Yarmouth deposit. The silica rock, or quartzite, of this deposit outcrops at Chegoggin point along what is known as the 'Pembroke shore', a northerly trending section of the coast-line at the extreme southwest of the Province, in Yarmouth county. The country here is fairly flat, with elevation averaging about twenty feet above high tide, and is for the most part mantled by a growth of brush and some scrub trees, chiefly small fir. Bed-rock is generally concealed beneath three to four feet of clayey soil, but scattered outcrops of the quartzite indicated that a band of this rock, some 260 feet wide, extended inland in a northeasterly direction from Chegoggin point at least to Utleys lake, a distance of about three miles.

Jan 1, 1947

By R. R. Potter

"New Brunswick became a separate province in 1784, shortly after the influx of a large number of Loyalists from the United States. Many of these people settled along the Saint John River, including the area of excellent farmland near the present town of Woodstock. There were indications that some of these early settlers recognized iron formations in the vicinity of Woodstock about 1820, however the nature of the deposits was not known until 1836 when Dr. C. T. Jackson, a geologist commissioned by the State of Maine, investigated the mineral potential of the area. Jackson(1) described the ""ore"" as compact red hematite yielding 44 per cent pure metallic iron, and suggested that sizable tonnages may be present. It was about this time that an extensive limonite deposit was found in north-central Maine, near Mt. Katahdin. Other iron depostis were found in the Nictaux area of Nova Scotia, and a few years later at Londonderry* (Fig. 1). In 1837, Richard Ketchum of Jacksonville, on whose land iron ores had been found, petitioned the provincial government to incorporate a company. After much study, the York and Carleton Mining Company Bill was passed on March 15, 184 7. Several other petitions were passed permitting the company to construct roads, obtain woodland, etc. (2) . The first blast furnace was erected in 1848 on the west bank of the Saint John River near the mouth of Lanes Creek."

Jan 1, 1999

By Y. G. Seredkin, A. A. Vasiliev, A. Y. Senchenko, A. V. Aksenov

"Autoclave oxidation, bacterial and chemical liberation, roasting, acid oxygen processes, atmospheric oxidation prior to cyanidation are applied to process refractory sulphide concentrates. It is obvious that the processes with the maximum effect regarding gold recovery are those in which complete destruction of sulphides takes place and gold becomes accessible for further cyanidation through liberation from sulphide “capsula”. But the significant recovery increase is often accompanied by a process complexity, high expenses for equipment purchase and maintenance. It makes material processing costinefficient. Process optimization has led to progress in ultrafine grinding, bacterial and autoclave oxidation processes. In our opinion sulphide atmospheric oxidation processes are the most interesting as oxidation there runs without high temperature (up to 100°?) and excess pressure (open units), and with acid environment close to neutral. The process of sulphide concentrates treatment named “Albion” (Albion Process™) represents a combination of ultrafine grinding and oxygen oxidation without pressure and external heating. The process has a number of advantages: sodium cyanide consumption decrease during gold leaching and high ecological compatibility. TOMS institute in collaboration with Glencore Technology Pty ltd (Australia) tested Albion technology aiming at liberation of finely disseminated gold from flotation concentrate produced from refractory ore of one Russian deposit. The testing has shown that Albion technology makes it possible to process refractory products with quite small capital investments. It enables involving medium and small refractory gold deposits into processing.INTRODUCTIONThe considerable part of the world Au-bearing reserves is present by refractory ores with finely disseminated gold. Gold in such ores is often associated with sulphide minerals and locked in so called “sulphide capsula” since it is closed inside dense sulphide grains and inaccessible to recovery by cyanidation. To treat refractory sulphide concentrates containing gold a number of processes were developed and they can be divided into three groups (Figure 1)."

Jan 1, 2016

By Paul T. Fitzgerald

Risk financing solutions are emerging to fully address environmental liabilities for mining operations. Supported by specialized insurance and alternative risk transfer (ART) products, mine owners can fund, cap and guarantee the environmental liabilities and closure obligations of a mine within a financial structure that will be acceptable to regulators. An environmental risk financing program will permit an owner to transfer the liabilities and indeed the ownership of a site to a third party that has the ability and resources to responsibly execute the closure plan. A properly structured program will be financially viable for the owner and will also respond to community and environmental opposition concerns about sustainable development and the environmental legacies associated with mining activities.

Apr 1, 2005

By K. Regl, J. Berneder

"AMAG investigated different aspects to improve the resistance against grain coarsening in aerospace alloys during recrystallization and was successful in finding several opportunities to minimize this effect. The studies show that one aspect to counteract grain coarsening is the chemical composition and subsequently all phases that are formed during homogenization. Starting with a fine grain (~ 50 µm) can lead to a final grain size of few mm. On the other hand with a coarse initial grain size (approximately 150 µm) and the right chemical composition the grain size can stay almost constant despite different deformation steps. Additional we investigated different sequences for the component production to eliminate the problem of grain coarsening as a coarse grain has a detrimental effect on product performance.INTRODUCTION In the aircraft industry, aluminium sheets are most commonly deformed in their soft state, followed by solution heat treatment and natural or artificial aging. If the preceding deformation is in a critical amount, during the recrystallization at solution heat treatment grain coarsening can occur. A subsequent deformation to this condition leads to an orange peel surface, which requires additional polishing. Next to this extra effort the coarse grain size produces a drop in the mechanical properties, often below specification limits. If there is no subsequent deformation, this effect is not visible and without destructive testing there is no possibility to detect the error. As mentioned before, this effect occurs during recrystallization, which is a process that is driven by the stored energy in the microstructure. The two most important aspects for an increase of the stored energy are the increase of the grain boundaries fraction (smaller grain size) and the increase of the dislocation density caused by deformation. The increase in dislocation density during the deformation arise from trapping of existing dislocations and from the generation of new dislocations. During recrystallization all grains are built completely new, so all dislocations are removed (Humphreys & Hatherly, 2004). There are three requirements for recrystallization:"

Jan 1, 2018

By Walter Koellner

Today?s large electric mining shovels are significant users of power and represent peak loads of more than 3.5 MW to a mine?s distribution system. The power swings during normal operation can influence the line voltage at the Point of Common Coupling (PCC). The static converters for the shovel?s motions also create voltage and current harmonics which are fed back into the mine?s power grid. In addition, shovels themselves are affected by the power quality of the mine?s distribution system. This paper introduces the use of active IGBT rectifiers, also called Active Front Ends (AFE), as alternative to conventional, line commutated SCR thyristor rectifiers. The AFEs convert the AC line input into a controlled DC-link voltage. This DC voltage is then used as input to IGBT inverters, which power the AC motors of the shovel?s Hoist, Propel, Crowd, and Swing motions. The introduction of AFEs creates the following operational improvements: i) reduction of the Harmonic Current Distortion THDi from more than 40% to less than 4%; ii) full regenerative operation; iii) the potential for line voltage stabilization at the PCC; iv) high tolerance for line voltage fluctuations; v) improved dynamic performance, and, as result vi) higher availability and productivity of the shovel.

May 1, 2001

By L. Mercier, R. Narendrula, F. Desmarais, L. Amaratunga, A. Aledresse

Thiosulfate is recognized as a promising alternative lixiviant to cyanide for the extraction of gold from ore bodies. Gold thiosulfate ([Au(S2O3)2]2), however, is not well-adsorbed by activated charcoal, making industrial scale use of thiosulfate for gold leaching impractical at present. Because of their high specific surface areas (500-1000 m2g-1) and uniform open-framework nanoporosity (pore channel diameters in the range 3-10 nm), functionalized mesoporous silicas are widely recognized as highly effective materials for the selective, rapid and high capacity uptake of mercury, gold and platinum group ions. In the present work, the efficient and rapid adsorption of gold thiosulfate by thiol-functionalized mesoporous silica (hereafter designated MP-HMS) is demonstrated, whereby the thiol groups in the materials bind with the gold complexes by ligand displacement. The adsorbed gold could be leached out using cyanide, regenerating the adsorbent for further uptake cycles. Functionalized mesoporous silica is thus a promising candidate for the preconcentration of gold from thiosulfate leachate solutions.

Jan 1, 2011

By K. D. Watson

"THE Mindamar zinc-lead-copper mine, owned by Mindamar Metals Corporation Limited, is at Stirling in Richmond County, near the south-eastern shore of Cape Breton Island, Nova Scotia (Figure I). It is connected by several roads with the Canadian National railway at Sydney and St. Peters.The deposit is said to have been discovered around 1895 as an outcrop in the bed of Copper brook, but the details are obscure. Not until 1925, when it was optioned by American Cyanamid Company, was it developed underground. Between 1927 and 1938, the 1-nine was operated intermittently by The British Metal Corporation (Canada) Limited, and yielded approximately 200,000 tons of ore averaging about IO per cent zinc, 2 per cent lead, I per cent copper, and small quantities of silver and gold. In December 1950, Dome Exploration (Canada) Limited made an agreement with Mindamar Metaî Corporation Limited, which was exploring the old mine, to assume management and prepare the property for production. Production started in April 1952 with a new mill and a new four-compartment shaft, and between that time and the end of 1954 it has totalled 545,347 tons of ore averaging 5·89 per cent zinc, 1·35 per cent lead, 0·66 per cent copper, 0·032 oz. gold, and 2 151 oz. silver.The Mindamar orebodies are irregular lenses and large veins lying within a wide, almost vertical shear zone of remarkable persistency. The shear zone consists mainly of well-foliated sericite schist derived from siliceous siltstone, and it contains a vast amount of dolomite and magne-site of hydrothermal origin. Most of the ore is extremely fine-grained and some of the high-grade material has a conspicuous thinly layered structure. The metallic minerals, in order of decreasing abundance, are pyrite, sphalerite, chalcopyrite, galena, and tennantite; the gangue minerals, in the same order, are dolomite and magnesite, quartz, sericite, talc, chlorite, barite, albite, and alunite.The geological setting of the deposit is shown in Figure 2. Except along streams and lake shores, almost all of the bedrock is concealed by glacial drift. The group of rocks in which the deposit occurs consists principally of greywacke, siltstone, tuff, brecoia, and Javas, and has been correlated lithologically with the Bourinot group of Middle Cambrian age. A short distance west of the mine, these rocks are in contact along the Stirling fault with conglomerate, arkosic sandstone, and quartzite belonging to the Middle River group of Silurian or Devonian (?) age, which elsewhere in the area overlies the Bourinot group unconformably. The large bodies of granitic rocks in the region, and the large lenticular masses of diorite and quartz diorite associated with them, have been assigned by Weeks (5, pp. 68-69) to the Devonian."

Jan 1, 1949

By C. Hari Manoj Simha, J. Gholipour, M. J. Worswick

Due to the high pressures involved in the hydroforming process, friction and lubrication play an important role and can affect formability of the material. Tubes of A1Mg3.5Mn aluminum alloy, of 76.2 mm (3 inch) outside diameter and 2-mm thickness were considered in this study. Three kinds of lubricants, Al070, Hydrodraw711 and water, were applied to the tubes and tubes were hydroformed to burst in a square shape die cavity. The key process parameters were recorded during the tests. An in-house Gurson-Tvergaard-Needleman (GTN) damage-based material model, implemented in LS-DYNA, was used to model the process and predict the formability of this material. The applied axial loads and internal pressures recorded during the tests were used in the computations. The effect of different types of elements (solid and shell) with different constitutive models (von Mises and GTN models) in predicting the strain distribution is studied. The GTN damage-based material showed a good ability to capture necking and displacement histories in this process. Both predicted and measured results showed that the lubricant with lower coefficient of friction can effectively increase the comer expansion.

Jan 1, 2006

By David J. Forrester

Light metals, most commonly aluminum, magnesium and titanium, and alloys containing them, are used in many industrial applications where lightness, hardness, ductility and resistance to corrosion are needed. However, these metals and their alloys can be potential ignition sources in underground coal mines. There have been documented cases in the past where coal mine explosions have been attributed to firedamp/coal dust ignitions involving light metals or their alloys. When light metals and their alloys are brought into contact with oxygen bearing material, such as iron oxide (rust) in the presence of heat, then a "thermite" reaction can occur. This source of heat can be generated from frictional contact or from merely a glancing blow. This paper outlines the hazards associated with light alloys, how to address the hazard and regulatory aspects.

May 1, 2001

By J. Shanks

In 1920 the writer presented some notes, embodying his experience with storage-battery locomotives as main under-ground haulage-motors at Brazeau collieries. (1) Since that date these motors have stood up well to the test of maximum output and heavy overloads, having accomplished all that was expected of them. The notes presented in 1920 gave a brief description of the conditions under which these motors were working at Brazeau collieries, also the cost, per ton mile, of operating them. The cost per ton mile has since then been appreciably reduced, by working the locomotives nearly to capacity and under more ideal haulage conditions, on both shifts. It is not the intention of the writer to repeat what was written in 1920, but rather to give members the benefit of his experience in operating different types or designs of locomotives; to draw their attention to the drawbacks of some designs, and to the improvements made in some of the more recent storage-battery locomotives put on the market, as regards efficiency, upkeep, and safety. Because of their flexibility storage-battery locomotives have advantages over any other type of haulage, where grades are suitable to their use. The number in use in the mines in the United States has increased enormously during the past few years, and this method of haulage is, at the present time, attracting the attention of British and Continental mining engineers.

Jan 1, 1924

By F. Fournier Dit Chabert, F. Tancret, J. François Castagné, R. Le Gall

During the repair of turbine blades by a laser cladding process, it is observed that interdendritic cracking occurs in the heat affected zone (HAZ). Auger electron spectroscopy, performed on sample broken at high temperature, reveals interfacial sulfur segregation, which is known to be one of the main causes of microcraking in the HAZ during welding processes. Moreover, thermal gradients generated by the process are responsible for important thermomechanical stresses. In the present work, the finite element code Comsol Multiphysics is used to simulate the laser cladding process in order to determine both the thermal field and, using an elastoplastic law, the stress field inside the component. The originality is that the temperature history calculated in the thermomechanical model is extracted then injected in a segregation model in order to calculate the local segregation behavior. This model can be eventually used to predict the risk of cracking as a function of process parameters and alloy chemistry.

Jan 1, 2006

By F. N. Smith

Corrosion was observed on the aluminum pressure plates and dress-caps that hold the glazing in place on a curtain-walled building, The multi-storey building in question is situated in the downtown area of a busy Canadian city, For aesthetic reasons, the original design required the dress-caps (which have L-shaped cross-sections) to be externally clad with thin copper sheet. Since the aluminum was in direct contact with the copper trim, galvanic corrosion developed that resulted in damage to the aluminum components, Soluble corrosion products washing off the copper trim may also have contributed to the accelerated corrosion of the aluminum, The aluminum pressure plates and dress-caps are being systematically replaced with components made of fibre-reinforced plastic. The outsides of these new components will be clad with thin copper sheet in order to preserve the original appearance of the building.

Jan 1, 2005

By LeRoy A. Thorssen

The use of lightweight aggregate as a constituent of concrete is not a recent development. Pumice was used by the early Romans, in pozzolana cement concretes, in the construction of many of their works. However, the recent development of manufactured lightweight aggregates, such as the expanded shales, vermiculite and perlite, has created a possible use for a whole new group of Portland cement concretes. Concrete can now be produced with unit weights ranging from 30 to 150 pounds per cubic foot and with various insulating, fireproofing, acoustical and structural properties. The tonnage of such materials being used has increased considerably in each of the past ten years, and can be expected to increase for the next several years as availability of the aggregates becomes more widespread and the properties of such concretes become more thoroughly investigated and more generally known. LIGHTWEIGHT aggregates of many types have become avail-able to the construction industry in most localities on this continent

Jan 1, 1963

By Mohammad. M. Khajeh

Rock mechanical properties are important parameters in geomechanical simulation. Considering stochastic heterogeneous models rather than conventional homogeneous layer cake models leads to more realistic simulation results and uncertainty assessment. These heterogeneous models are usually fine scale models generated by geostatistical techniques. Although considering high resolution property models is desirable, geomechanical simulation with a fine scale model is not computationally feasible for full?field, coupled geomechanical-flow simulation. Upscaling of property models is necessary to move from fine scale/high resolution property models to coarser scale/low resolution models appropriate for simulation. Local numerical upscaling was proposed by Khajeh et al. (2012) to describe the macroscopic elastic behavior of complex heterogeneous media and is expanded upon in this work. This numerical technique is not restricted to specific geologies as typical analytical techniques are. Moreover, transversely isotropic deformation is considered rather than the usual assumption of isotropic deformation. To compare the accuracy of the upscaling methodology, in this study shear strain is considered as the geomechanical response of a synthetic facies model and the response of the coarse scale model is compared to other conventional analytical averaging techniques. It is found that the numerical upscaling technique better approximates the geomechanical response of the fine scale model.

Jun 1, 2012