Search Documents

By Sunil Koppalkar, A. R. Laplante

"A Pilot Plant was installed in one of the grinding circuits of the Dome Mill, Ontario, Canada. Tests were conducted on a KCCD12 Knelson Concentrator to systematically analyze the effect of operating variables on the performance. The main objective of this test work was to explore the effect of very coarse (6 mm) feed size on GRG recovery and performance of the Knelson concentrator. Preliminary results have shown that coarse feed size is deleterious to maximizing recovery. Size-by-size GRG recoveries have shown an unusual trend in the sense that recoveries do not decrease monotonically with decreasing gold particle size. Similar trend observed in one other full-scale unit has been compared. The observed trend is probably linked to the feed size distribution and top size.INTRODUCTIONKnelson Concentrators are the most widely used semi-continues centrifuge gravity separation units for the recovery of gold and platinum group minerals (Xiao and Laplante 2004). The main advantages over the competing centrifugal gravity units are their design, operating simplicity and good separation efficiency that make them the most common choice for gravity circuit. Despite some characterization at bench scale and a limited characterization at full scale, there is a lack of a comprehensive study of impact of operating variables on efficiency that reflects realistic full scale operating practice. GRG characterization studies, at bench scale, on these units provide information about the occurrence of gold in ore samples but fail to provide adequate information about the effect of operating variables for full-scale units. It is well known fact that such work is difficult to undertake on full-scale units owing to the difficulties involved in sampling and systematic variation of operating parameters. To tackle these problems, a pilot facility consisting of a 12-in CD Knelson Concentrator, a feed screen and tailing pump was installed in one of the grinding circuits of Dome Mill. This paper describes the work carried out and the results.Porcupine Joint Venture (PJV)Porcupine Joint Venture was formed in 2002 between Placer Dome Inc. and Kinross Gold Corporation. The JV utilizes the milling capacity of the Dome Mill to process ore from Placer Dome and Kinross mines. The Dome Mill circuit has gravity concentration, cyanidation and CIP circuits to recover gold. Gravity recovery has been used at Dome Mill since inception to recover gold: first by using conventional jigs, which were eventually replaced by two Knelson Concentrators in 1993, one in each of the grinding circuits. Three more Knelsons joined the circuit in 2002 to improve gravity recovery. An Acacia Intensive Leach Reactor was also added in 2002 to process gold concentrates replacing shaking tables (Chong et al 2004)."

Jan 1, 2007

By N. W. Kirshenbaum

"The Marconaflo slurry system was originally developed to reduce costs and solve technical problems in the marine transport of mineral cargoes. In the short time since its inception, it has been found to offer economies and advantages for land-based and in-plant materials handling. This efficient method of reclaiming and slurrying particulate materials at very high pulp densities can be directly utilized in a wide variety of mineral process systems. These include: storage-reclaim applications, where even cohesive, compacted materials can be reclaimed from settled storage ""on demand""; the growing number of hydrometallurgical operations wherein slurried materials are processed to extract or yield metals; certain applications associated with pyrometallurgical treatment; and as a means of augmenting the performance of conventional mineral dressing equipment, such as thickeners.INTRODUCTIONIn the continuing effort to lower costs of producing minerals and extracting metals, the field of handling and transportation often receives too little attention from those engaged in the mining and winning of ores and metals. This comment, which pertains to ferrous and non-ferrous as well as to non-metallic producers, is especially pertinent to products having relatively low value, where transport costs can be a major portion of the delivered selling price to the minerals receiver.One method which was developed recently for the purpose of reducing costs and solving technical problems in marine transport and handling of mineral cargoes is the MARCONAFLO slurry system. A notable feature of this system is its versatility; in addition to its use in marine transport1*, some of its diverse applications have included the mining and reclaiming of tailings2 and in-plant materials handling3. As the concept and fundamentals of this system have been well explained previously4,5, the mechanics of the system will not be elaborated upon here. Rather some specific ways in which MARCONAFLO can be applied to processing and extraction will be explored."

Jan 1, 1973

By B. P. Simser, R. K. Brummer, A. Mortazavi, P. P. Andrieux

"A large-scale panel destress blast was fired at Brunswick mine in the fall of 1999 in order to reduce the ground stresses in a critically important neighbouring mining region. This work, sponsored by the Mining Division of CAMIRO and Brunswick mine, consisted in heavily choke-blasting — and subsequently leaving in place — a massive waste sulphide pillar in the southwest end of the 1000 m level. This paper describes the approach and design methodology used to try to maximize breakage in the rock mass in the area to destress, while minimizing damage to critical infrastructures in the vicinity. The loading operations, as well as the results of the blast — in terms of its field performances, as recorded by near-field blast vibration monitoring equipment, visual postblast assessments and measured impact on the regional stress field — are discussed as well. A brief comparison between the measured stress changes and inelastic numerical modelling of the test site is also presented.Un tir à grande échelle de relâchement des contraintes dans un pilier a été effectué à la mine Brunswick à la fin de l’automne 1999 dans le but de diminuer les contraintes de terrain dans une très importante zone de production adjascente. Ces travaux, financés par la division minière de CAMIRO et la mine Brunswick, consistaient à tirer violemment sans aucune face libre, et à laisser en place, un pilier de sulphures massifs au sud-ouest du niveau 1000 m. Cet article décrit l’approche et la démarche conceptuelle utilisées pour tenter de maximiser les fractures dans le pilier visé, tout en minimisant les dommages collatéraux à des infrastructures critiques se trouvant dans les environs immédiats. Les opérations de chargement des explosifs et les résultats du tir — en termes de ses performances, telles qu’évaluées par de l’équipement de monitoring rapproché des vibrations de tir, d’observations visuelles, et de son impact sur les contraintes de terrain locales — sont également discutés."

Jan 1, 2003

By Tatiana Ravani von Ow, Leandro Bomvisinho

"The size of mills driven by ring-gear or by a gearless solution has significantly increased in the last years. This has created additional challenges for the driven equipment. The requirements for the mechanical devices and the power grid have become more demanding. Controlled soft starting and operation, especially in dual pinion mills, as well as the protection of the equipment has gained importance. The selection of the drive solution for the mill therefore becomes more critical. Besides the classical criteria such as performance, efficiency and capital costs other factors come in the evaluation of the system such as flexibility and optimization of operation, reliability and the ageing of the grinding equipment.Variable speed solutions offer significant advantages over conventional fixed speed drives due to their application specific features and process optimization capabilities, even for ball mills where these are not seen yet as a must.The initial capital costs are higher than some of the direct on-line solutions however the benefits for the operation during the lifetime of the mill generated by the use of converter solutions justify the additional higher investment.INTRODUCTIONThe method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said; almost every decade in the last half century had its own trend. The trend was dominated by the market demand, by the process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology.All has started about 50 years ago with mill diameters less than 20 feet driven by fix speed synchronous or wound rotor motors with the power of about 2 MW. Around 10 years later, the mill sizes increased, but the necessary torque could not be transmitted by one pinion therefore dual pinion solutions were developed to power the mills. However, realization of the dual pinion solution was only possible when load could be evenly shared between the two pinions."

Jan 1, 2010

By M. Sturzenegger

This paper documents a field survey using long-range terrestrial digital photogrammetry at the Palabora open-pit mine, South Africa, for multi-scale characterization of rock mass discontinuities. Stereomodels covering the entire mine were generated based on photographs taken from a distance of 1600m across the pit, using a series of f=20-400mm lenses. Details on the methodology used and its accuracy are discussed. Preliminary results on discontinuity orientation, persistence and intensity are presented, highlighting the effect of observation scale. The potential uses of long-range terrestrial digital photogrammetry in open-pit mine and large natural rock slope environments is emphasized. The use of an f=400mm lens from distances larger than 1.5km may represent an important step forward in the geotechnical characterization of inaccessible remote rock faces.

May 1, 2009

By Cameron J. Clayton

Cumberland Resources Ltd. is currently planning to develop the Meadowbank Gold Project located some 70 km north of Baker Lake, Nunavut in the eastern Canadian Arctic region. The Meadowbank Gold Project currently consists of up to 6 main gold bearing deposits within relatively close proximity to one another which are planned to be mined primarily as a truck-and-shovel open pit operation and using conventional gold milling and extraction. The mining plan indicates that approximately 20 million tonnes of ore will be mined over a mine life of 8 to 10 years. The operation will generate approximately 160 million tonnes of mine waste rock and about 20 million tonnes of tailings. The site is located in an area of continuous permafrost with mean annual average air temperature of -11 °C and average annual precipitation in the range of 100 to 200 mm. Lakes cover a large portion of the site, including some of the ore deposits. The location of the site, and the physical environment, pose challenges to development. This paper presents some of the designs considered to effectively manage and utilize the waste products of mining at the project.

May 1, 2004

By Colin Hardie, Simon Pelletier, Rakan Rhabani, Guy Comeau

"In order to improve the nickel concentrate thickener operation at Raglan Mine, two pulp deaeration cyclones were installed. These units obtained from Outotec Pty Ltd, also called the FrothBuster®, have been in continuous operation since mid-October 2006. The primary objective of the de-aeration cyclones is to lower the solids content in the thickener overflow by de-aerating the concentrate pulp before it enters the concentrate thickener. This dearated slurry should help decrease the nickel particle losses that report to the thickener overflow because of the flotation effect within the thickener.Optimizing the de-aeration cyclones has been a slow and ongoing process, however, initial testing is encouraging. The latest test results indicate a 50 % reduction (0.070 to 0.035 % solids) in nickel losses to the concentrate thickener overflow resulting in an additional $350,000 in annual revenues.This paper will present an overview of installing the de-aeration cyclones within a limited space, as well as the preliminary commissioning and testing challenges. This paper will also discuss the most recent concentrate thickener operating results since the de-aeration units were installed.INTRODUCTIONThe Xstrata Nickel Raglan Concentrator, located at the northern limit of Quebec’s Nunavik Region has been in production since 1997. In early 2002, the concentrator implemented the Zero Process Water Discharge (ZPWD) project to recycle the process water to decrease fresh water consumption and reduce discharges to the environment. Due to this initiative, the chemistry of the process water changed significantly resulting in flotation concentrate streams, which were very frothy and difficult to manage. This phenomenon has resulted in operational challenges in many areas of the concentrator including slurry pumping, flow measurement and concentrate thickening.In October 2005, the Raglan Mine underwent a conversion from an AG mill to a SAG mill operation in order to increase throughput and to optimize key process areas. As part of this project, the first two North American pulp de-aeration (FrothBuster®) units from Outotec were installed to improve the operation of the concentrate thickener. The primary objective of the deaeration technology was to lower the solids content in the thickener overflow by de-aerating the concentrate thickener feed pulp. This in turn was to reduce the froth, which accumulates on the thickener surface, and more importantly reduce valuable nickel losses to the thickener overflow because of the flotation effect within the thickener."

Jan 1, 2008

By Olaf Andersen

Crucible melt extraction yields short metal fibers with eqivalent diameters as low as 50 µm from almost arbitrary metals and alloys. Highly porous components can be made from such fibers by suitable deposition and sintering methods. This technology is being developed at the Dresden based Department of Powder Metallurgy and Composite Materials of the Fraunhofer Institute for Manufacturing and Advanced Materials (IFAM) and has been applied to gold alloys and iron-base alloys containing small additions of precious metals. From the manufactured gold fibers, sintered structures were made for decorative applications. Additionally, it was found that due to rapid solidification during the fiber formation, precious metals can be finely dispersed in ironchromium- aluminum (FeCrAl) and FeAl20 alloys. Good catalytic activity at elevated temperatures was found in compositions containing 3 wt.-% Ce and 0.5 wt.-% Pt.

Oct 1, 2003

By Véronique Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modeling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioniong of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

May 1, 2003

By Manqiu Xu, Glen Robertson, Steve Wilson, Pete Quinn

"The middlings circuit, once called the pyrrhotite rejection circuit, at Inco’s Clarabelle mill was a single flotation stage. It used to process a combined feed consisting of the main flotation scavenger concentrate and the non-magnetic portion of the magnetics flotation circuit tails. The typical circuit metallurgy was 55% nickel recovery at 6.5% Cu+Ni concentrate grade. In the past few years, a research project with the objective of improving the circuit metallurgy was initiated between Inco’s research laboratory and the Mill’s Process Technology group. This project has gone through three steps: a) initial laboratory studies, b) on-site pilot plant investigation, and finally c) full plant implementation.The present paper describes the initial laboratory test work. The development of a two-stage circuit consisting of separate rock and pyrrhotite rejection stages to replace the simultaneous rejection of both rock and pyrrhotite in a single stage is discussed. A two-stage circuit simulation based on batch laboratory flotation data is also presented. Further development work, including the on-site pilot plant test work and the plant implementation of the new circuit design, will be described in a later publication.INTRODUCTIONThe milling operation at Inco’s Clarabelle mill, Copper Cliff, Ontario processes a rich complex sulfide ore from several large production mines around the Sudbury basin (Agar, 199 1). The sulfide mineralization is simple, consisting of chalcopyrite (Cp), pentlandite (Pn) and pyrrhotite (Po). The main gangue minerals are pyroxene, feldspar and quartz with minor amphibole and talc. Estimates of mineral composition are routinely calculated from Cu, Ni and S assays. In the mineralogical calculations, all gangue minerals are conveniently grouped and treated as rock (Rk)."

Jan 1, 2000

By J. Coffin, R. Multani, C. Deredin

Glencore’s Strathcona Mill has recently evaluated a pyrrhotite depressant combination of diethylenetriamine (DETA) and sodium metabisulfite (SMBS) to improve its overall plant pyrrhotite- pentlandite (Po-Pn) selectivity, with the aim of producing a higher quality nickel concentrate. In a previous paper, key findings from a comprehensive lab-scale program (completed at the XPS Centre) were summarized where, of the depressants tested, DETA/SMBS combination was found to be the most effective in improving the Po-Pn selectivity. The present paper describes the metallurgical program recently completed at Strathcona Mill; DETA/SMBS evaluation on select plant “grab” samples as well as the major results of three DETA/SMBS plant trials conducted on several plant ore feeds (long-term testing). Interestingly, it was found that there was variable success in using DETA/SMBS depressants on the different plant ore feeds; DETA/SMBS (dosage: 25/50 g/t milled feed) on lower Cu feeds demonstrated a ~2% Ni recovery increase at the same Ni grade. On the other hand, higher Cu feeds demonstrated virtually no benefit from DETA/SMBS at the same plant dosage, suggesting that higher DETA/SMBS dosage (at specific locations) than that tested is required to overcome the increased Cu-DETA complexation for these particular feeds. Glencore Nickel – Sudbury Integrated Nickel Operations owns and operates Strathcona Mill which has been processing Ni-Cu ores from the Sudbury Basin since 1968. The valuable sulfides are pentlandite (Pn) – (Ni,Fe)9S8 and chalcopyrite (Cp) – CuFeS2, majority of the sulfide gangue is pyrrhotite (Po) – Fe(1-x)S [0 < x ≤ 0.125] which is present in two forms: hexagonal Po (Fe9S10) and monoclinic Po (Fe7S8) (Multani & Waters, 2017; Lawson et al., 2014). Currently Strathcona Mill processes ore mined from two primary sources from the Sudbury area and produces two concentrate streams: (1) nickel-copper concentrate that is sent to the Sudbury Smelter; and (2) copper concentrate that is shipped to the Fonderie Horne (Glencore Copper, Rouyn-Noranda).

Jan 1, 2019

By Hannu J. Häkkinen

Metal clusters exhibit unique size-dependent physical and chemical properties that differ from those of bulk materials or large particles. Here we discuss recent theoretical investigations of the catalytic properties of free and MgO-supported gold clusters. The catalytic activity of gold clusters depends sensitively on the environment, charge state, and chemical composition of the catalyst. Relativistic bonding effects stabilize large planar structures for gas-phase gold clusters, and non-compact ?quasiplanar? structures are present as important isomers also for surface-supported clusters. The hybridization of the atomic 5d and 6s states is significantly enhanced by the relativistic effects, and large spatial variations in the nature of the local electronic structure make the low-coordinated gold atoms preferable adsorption sites for oxygen molecules. The adsorbed oxygen molecules are activated to superoxo- and peroxo-states via charge-transfer from gold, and Eley-Rideal and Langmuir-Hinshelwood reactions with CO proceed via low-barrier formation of intermediates, which do not require O-O dissociation as precursors. This facilitates the low-temperature (below 300 K) activity of gold nanocatalysts in CO oxidation. Other gold nanostructures, such as mono-atomic gold nanowires, may also become important prototype systems in chemical sensing and nanocatalysis; here we show that they are active promoters of hydrogen dissociation.

Oct 1, 2003

By S. H. Ward

An account of a new method of investigating the electrical .properties J the earth&apos;s crust is presented. The method, called AFMAG, employs, as a source, natural alternating magnetic fields of audio and sub-audio frequencies. Measurements of the distortion of these fields caused by geological features are made with the aid of search coil detectors at several discrete frequencies. Many results of field surveys made with the method are presented and they illustrate its advantages and limitations when applied to the search for massive sulphide mineralization. The advantages far outweigh the limitations and in fact indicate that a major breakthrough in geophysical exploration technique and instrumentation has been made.

Jan 1, 1958

By Alan M. Jessop

This paper discusses the distribution of frozen ground in the zone of discontinuous permafrost in relation to the pattern of surface temperature. The importance of understanding permafrost in relation to surface construction and open-pit mining operations is stressed.

Jan 1, 1972

By A. L. Mular, R. P. Edwards

"The operation of flotation circuits is often regarded as a combination of art and science. Expert systems offer a method by which the art may be captured and supervisory control of flotation circuits fully realized. Operating knowledge, the art, can be consistently employed to enhance regulatory control through the judicious application of an expert system. Using an expert system, a supervisory control routine was developed, and successfully implemented, in the copper flotation circuit at Brenda Mines Ltd.The expert system ran in conjunction with regulatory PI controllers on a personal computer. The expert system received assays via an on-stream analyzer and adjusted regulatory loop setpoints as required in real-time. From its commissioning in November 1989, to the end of the mine's operation in June, 1990, the ES was enthusiastically embraced by the operators and attained operating levels superior to those achievable manually.INTRODUCTIONExpert system (ES) software springs from research into artificial intelligence and is currently making significant inroads into business and industry. Proponents of ES's make many attractive claims; they are a means of capturing the knowledge of experts and they can be programmed by non-programmers. To date, most uses of this software in the process industry are in off-line applications, meaning that the applications are not tied directly to operating (on-line) environments. Moreover, in on-line environments, they are typically employed as advisors and only suggest changes. Human operators are required to close-the-loop to the process. Yet, ES's should be applicable to operating environments and, if the claims of the proponents are valid, should also be better than existing tools. As an intelligent controller an ES must use the knowledge of experienced operators, apply it directly to a process and do this without the intervention of human operators. On-line applications have been successfully employed in the closed loop control of SAG circuits (Herbst et al., 1989) and flotation circuits (Hales, 1989). Harris and Kosick (1988) detail an implementation for flotation control at the Polaris Mine."

Jan 1, 1991

By M. W. Lewis

A mine&apos;s inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine &rsquo;s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By M. W. Lewis, B. Sambirsky, J. Werner

A mine’s inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By Sengpasith Houngaloune

Arsenic, which is a toxic and carcinogenic element, causes serious environmental problems throughout the world. It is also known as a major contaminant in the non-ferrous mining and extractive metallurgical industries, thus its disposal is one of the most important environmental issues for the mining and metallurgical industries. In order to ensure a safe disposal environment for the final wastes, stabilization of arsenic has been studied extensively with various approaches. Solidification/stabilization (S/S) represents one of the most effective methods to reduce the availability of arsenic in soil and waste by transforming toxic or potentially hazardous phases into less hazardous ones. Cement based S/S processes could reduce the solubility of arsenic in solid waste, using inorganic binders such as cement, lime, and pozzolanic materials. A new tailings management technique, called cemented paste backfill (CPB), has become widely employed for improving mining techniques and for tailing storage purpose and this technique could also enhance arsenic stabilization, by fixing the contaminants in the binder matrix. Disposal of arsenic in the form of scorodite (FeAsO4?2H2O) has been widely accepted as currently the most suitable method for stabilization and the safest known storage material. The Bio-scorodite process has been reported to be more economic and environmentally friendly method than the chemical crystallization processes. Retention of arsenic by schwertmannite (Fe8O8(OH)6SO4), a metastable ferric oxyhydroxy sulfate mineral, has gained more attention in the recent years. Schwertmannite has a large specific surface area and high capacity to adsorb arsenic in solution. Several researchers have reported that the transformation of schwertmannite to goethite could be retarded by the presence of adsorbed arsenic; therefore schwertmannite might be viable alternative for long-term storage of arsenic. In this paper, various approaches used in arsenic stabilization are reviewed with emphasis on the development in the recent years.

Aug 1, 2013

By C. Larsen, D. Fragomeni, A. Vien, D. G. Fisher

"MOCCA is a Multivariable Optimal Constrained Control Algorithm developed specifically for non-square industrial control applications with practical difficulties such as interactions, time delays, constraints, modelling errors, etc. MOCCA consists of an off-line simulation/translation module, for tuning the control parameters, and an on-line module that implements the designed control law.This paper describes an evaluation of MOCCA on the Hemlo grinding circuit which comprises one open circuit ball mill and two closed circuit ball mills in series. In this case a 4x4 unconstrained control problem was considered. The manipulated variables included the fresh ore feed rate and three pump box water additions. The controlled variables were the grinding circuit product particle size and three pump box levels. In this application soft constraints were implemented through control action and control error weighting. The feedforward capability of MOCCA was used to compensate for a measured water flow disturbance to one of the pump boxes. MOCCA performed very well during plant evaluations when compared to the original classical multi-loop control strategy and proved to be quite robust. Perhaps most importantly, the process engineers and plant operators have a high level of comfort both in understanding MOCCA's general operating principles, and with its demonstrated performance."

Jan 1, 1991

By P. A. Riveros, W. D. Gould, R. Molnar, D. W. Koren, P. Bédard

This paper reports the results of the field demonstration campaign of a new process for removing and destroying ammonia from mining/ metallurgical effluent solutions. The 50-day campaign was carried out at a uranium plant in Saskatchewan, Canada. The process was developed by adapting and integrating two well established technologies: zeolite adsorption/ elution to extract the ammonia from the effluent stream and to produce a concentrated ammonia eluate; and conversion of the ammonia in the eluate to innocuous nitrogen by applying bacterial nitrification-denitrification (NH3 = > NO3 - => N2). The data show that reasonable target criteria were met, under very challenging operating conditions. Problem areas and possible causes for poor performance are identified. Preliminary and generic cost estimates of the process are also presented.

Jan 1, 2003