Search Documents

By M. C. Bétournay

Mine site infrastructure for storage and delivery of hydrogen must be standardized and acceptable for routine and safe industrial use before fuel cell technology is adopted as a major power source. An initial study reviewed possible options for production, storage and delivery of hydrogen for underground equipment. The high level review included assessment of economic, operational, technical, and health and safety risks. Following this review, a subsequent theoretical study to select typical minesite infrastructure and for construction at an operating research mine is outlined.

May 1, 2007

By Michael Drozd

"The operation of an activated charcoal system has five separate unit operations. These unit operations have common points for CIP, CIL and CIS system, which vary widely in application.The unit operations are:a. Absorptionb. Desorption (Stripping)c. Acid Washingd. Reactivatione. Carbon Handling (carbon transportation, sizing, dewatering, etc.)Cost optimization starts with the basic operating parameters (design philosophy) set down at the time of engineering design. These parameters undergo almost immediate change due to site specific ore requirements, throughput changes, operator requirements or reagent availability.Activated charcoal is sometimes viewed as simple, uncomplicated reagent that requires not optimization. To some extent, this statement is true, but under most circumstances, if the time necessary to optimize the use of activated charcoal is available, the effort is rewarded with significant savings. CPL-Carbon Link has embarked upon a program of supplying technical support with its activated charcoal. Several operations in the United States have undertaken to have CPL-Carbon Link do an operational survey to determine if potential savings are possible. CPL-Carbon Link has offered to do these surveys for projects that are clients or simply would like to have CPL-Carbon Link review their operation. The information accumulated by CPLCarbon Link is being used to attempt to fashion industry standards so that a common reference point can be established for activated charcoal usage."

Jan 1, 2008

By J. Ran

Ground instability is among the major causes of serious incidents and production disruptions in the mining industry and has a significant impact on safety. Mining companies may have operations in a number of jurisdictions with varied regulatory requirements for ground control management. As these companies expand into countries where mining regulations are formative or lacking clear definition, ground control practices are usually developed by local mine personnel based on their experience. In many cases, inconsistent procedures and standards are generated, which can lead to an increase in occurrence of underground incidents due to difficulties and confusion in implementation. This situation has forced some mining companies to standardize their ground control practices by geographic regions or divisions. Though this approach is an improvement, it may not lead to effective management of ground control issues across all operations of a global mining company. Barrick Gold Corporation, with operations in North and South America, Australia and Africa, decided to adopt a global approach to ground control management. This global approach requires all Barrick operations to prepare and implement an effective ground control management plan (GCMP) based on site specific conditions and company guidelines. It is also required that the GCMP be developed through application of sound geotechnical engineering practices and be consistent with local regulatory requirements and Barrick safety policies. All Barrick underground operations have GCMPs in place, and its surface operations are now involved in the initiative. This paper presents Barrick?s global approach to underground mine ground control management and outlines the content and process for the development of a GCMP.

May 1, 2006

By R. E. Whitehead

"Alkali/alumina and MgO/alumina molar ratio plots graphically portray both chemical and mineralogical changes accompanying potassic, phyllic, argillic, chloritic, and alunitic alteration of quartz monzonites and granodiorites hosting porphyry (as well as lode and greisen) ore deposits. The molar ratio plots can be used to identify different types of alteration. In most cases, the identification based on molar ratios coincides with petrographic data. In those instances where the molar ratio and petrographic identifications do not agree, the mineralogy might need to be re-examined. Hydrothermal alteration studies using trace elements could benefit from the application of complementary alkali/alumina molar ratio plots.Le diagramme des rapports molaires alkali/alumine et MgO/alumine illustre clairement les changements chimiques et minéralogiques qui accompagnent les altérations potassique, phyllique, argillique, chloritique, and alunitique des monzonites à quartz et des granodiorites encaissant les gîtes de type porphyrique, ainsi que des veines et des greisens qui leur sont associés. Les diagrammes de rapports molaires peuvent être utilisés pour identifier divers types d’altération. Dans la plupart des cas, l’identification basée sur les rapports molaires est en accord avec celle basée sur les données pétrographiques. Là ou il y a désaccord entre les rapports molaires et les données pétro-graphiques, il peut être nécessaire de réexaminer la minéralogie. Les études de l’altération hydro-thermale accompagnées d’une étude des éléments traces auraient avantage à utiliser un diagramme des rapports molaires alkali/alumine."

Jan 1, 2009

By Balakrishnan Nanthakumar, Marek Pawlik, Dennis Grimm

"The anionic flotation of a high-iron phosphate ore from Agrium - Kapuskasing Phosphate Operations was investigated through batch flotation tests in the presence of soda ash. The flotation data were supplemented by titration of the flotation pulp with soda ash, analysis of process water chemistry, and determination of the mineralogical composition of the ore. The results of lab tests were applied to the flotation circuit design allowing the flotation plant to efficiently process problematic ores. Process control measures (pH, conductivity) were also developed.Calcium cations and sulfate anions were identified as the dominant ions present in the process water when the difficult-to-process ores are beneficiated in the flotation plant. The concentrations of calcium and sulfate ions were consistent with the presence of a small amount of a calcium sulfate mineral in the ore although an oxidation/weathering process of iron sulfide minerals present in the ore could also be responsible for the observed water chemistry and subsequent flotation problems with the ores. The latter possibility suggests that the long-term stockpiling of such ores may have a highly negative impact on the flotation process.The role of soda ash in the flotation circuit is to precipitate metal cations from the pulp thus allowing the tall oil-based collector to selectively interact with the phosphate components.INTRODUCTIONPhosphorus minerals are the main source of this element for the production of fertilizers, and the froth flotation process is the most important technology for beneficiating phosphate ores. The flotation concentrate from Agrium-Kapuskasing Phosphate Operations (KPO) is transported to Redwater Fertilizer Operations in Alberta (also operated by Agrium) where the phosphate concentrate is converted into a phosphate fertilizer and other important chemical products. The KPO phosphate ores differ widely in mineralogy and phosphate grades, and are broadly divided on-site into three classes. The easy-to-float A-type ores do not pose any major flotation problems, but the B-type and “marginal” ores, which are quite common in the KPO igneous phosphate deposit, are not always readily-floatable using the current reagent suites and process parameters (pulp density, feed particle size, pH). In fact, marginal ores are presently considered impossible to process by flotation. A-type ores contain normally more than 15% P2O5 and less than 8% ferric oxide equivalent (Fe2O3). B-type ores are approximately of the same P2O5 grades as A-type ores but their iron content may reach 30% Fe2O3. Any material containing less than 15% P2O5 is rejected as waste rock."

Jan 1, 2008

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The slurry systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1500-2000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed with a larger diameter impeller and increased vane lengths, and is expected to triple Aurora’s mission length for hydrotransport pumps.INTRODUCTIONSlurry Pumps are Critical Equipment at SyncrudeSlurry pumps are a critical component in Syncrude’s operations. In a typical Aurora application, each pump stage helps move over 8000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1500-2000 hours, or 12-16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in higher than optimal impeller vane speeds for the service conditions.PROJECT BASISSlurry Pumps are the Reliability Bottleneck at AuroraSlurry pumps are currently the shortest-lived components that determine the overall system run length at Aurora, in Hydrotransport, Extraction and Tailings. Vibrating screens and piping had been previous bottlenecks, but their reliability has been improved through upgrades in equipment design and wear materials. Both vibrating screens and piping can now achieve 4000 hour mission lengths."

Jan 1, 2013

By E. Esponosa-Gomez, J. A. Finch, A. R. Laplante

"Water quality plays an important role in oxide flotation. The effects on selective flotation of fine (1-16 um) pyrochlore of two types of water used at the Niobec concentrator, potable and plant recycle, were assessed. Several pyrochlore collectors and silicate depressants were tested. Water effects were different for each mineral-reagents) combination. In general plant recycle water decreased selectivity and increased reagent consumption. Interpretation of results is given in terms of electrokinetic effects, hydrolysis of cations, and mineral-collector interactions. Two techniques of treatment for plant recycle water, cation precipitation and zeolite adsorption were assessed. The former was found to be more effective under the tested conditions but recycle water continued to give poorer selectivity than the potable.INTRODUCTIONWater quality plays an important role in selective flotation. Specific effects have been reported by many workers (1-6) and in general the better the water quality the more selective is flotation. Water composition depends on origin and the minerals being processed. For example pulp containing salt-type minerals (calcite, apatite, dolomite) will contain more Ca and Mg cations than that from a sulphide deposit. Another source of water contamination is the flotation reagents added to the pulp, particularly if water recycling is practiced."

Jan 1, 1986

By Flavio Rojos-Tapia, Oscar Pereira-Cerda, Samuel Sánchez-Pino, Samuel Sánchez-Baquedano

"Pneumatic flotation was introduced to the Chilean Copper Mining Industry in 1993 by Ingeniería de Minerales S.A. (IDM). The technology is based on the designs of Dr. Rainer Imhof from Germany, who is the designer of several different types of pneumatic flotation cells, already sold through his Company Maelgwyn Mineral Service Limited (MMH). The company is represented by Ingenieria de Minerales S.A. (IDM) in South America.Pneumatic flotation, has been used in tough industrial applications .It has been successfully used for metallic ores such as copper sulphide and oxide minerals, copper slag, silica and silicates from iron magnetic preconcentrate (reverse flotation) and gold. It has also provided promising results when applied to molybdenum flotation. The latest applications, with ultrafine molybdenum particles in operating plants, is showing the V and G Cell (end model designed) as a real technological alternative to conventional flotation., The G Cell is an extremely high speed flotation machine with high selectivity which introduces the possibility of producing a final molybdenum concentrate with only one stage of cleaning. This is a completely new development in molybdenum flotation in the industrial circuit which has the potential to dramatically reduce the circulating load in the cleaning circuit. As a consequence the capital costs of future Molybdenum plants may also be reduced. The suitability of the G Cell will have to be determined on a case by case basis but it provides the metallurgist with an alternate flowsheet for consideration.The good performance of the G Cell can be explained by the high gas hold-up and very effective micro-turbulence which helps improve the attachment of solid particles to the bubbles. This technology may change our traditional concept of residence time in flotation. Additionally, the rotation phenomena introduced in the vessel of the G Cell ,creates radial separation forces which are critical to achieving a more rapid separation of the target minerals from the tailing. This results in a much reduced residence time requirement in the flotation machine. Some benefits associated with the use of the new G Cell are: less energy consumption, less maintenance costs, simple and reliable circuit to operate and a small area required for installing the circuits.As a result of the industrial experience in the Chile, the pneumatic flotation type G Cell can be regarded as a technology which must be considered as a replacement technology for the rougher and cleaner stages for fine particle flotation."

Jan 1, 2008

Ontario Operaations Mining Garson Stobie Copper Cliff North Copper Cliff South Creighton Mcreedy East Milling Clarabelle Mill Smelting Smelter Matte Processing Anode Casting Refining Copper Cliff Nickel Refinery Port Colborne Cobalt Refinery

May 1, 2007

By D. R. Tesarik

Researchers from the National Institute for Occupational Safety and Health (NIOSH)1 and engineers from Placer Dome, Inc.2, conducted an underground rockfill span test at the Turquoise Ridge Mine near Golconda, Nevada, USA with the purpose of improving safety and increasing productivity by using a bulk mining method instead of drift and fill. A rockfill sill was constructed by mining and backfilling six adjacent, parallel drifts and then undercutting the sill with a 13.7 m (45 ft) wide and 30.5 m (100 ft) long room. Displacement measurements from vertical borehole extensometers installed in the mine roof and rockfill indicated that the sill remained stable with a maximum vertical deformation of less than 5 mm (0.2 in). These results were confirmed by visual observations and calculations from a validated three-dimensional numeric model of the sill. The numeric model was also used to simulate load on the sill produced by dislodged roof material in the shape of a 11.0 m- (36 ft-) high triangular prism with base measurements equal to those of the sill. Failure in the bottom third of the sill occurred with this additional load.

May 1, 2007

By Karl Nienhaus

The BGMR has developed a method for an online-analysis during drilling processes in cooperation with Fraunhofer Institute for Laser Technology in Aachen and various industrial partners. This allows for efficient utilization of deposits, maximum recovery of desired minerals and frequent and costefficient updates of deposit models. The used method, namely laser-induced breakdown spectroscopy (LIBS), was implemented into a compact demonstrator in order to analyze drill dust and loosened material within mining environments and directly on drill rigs. The consequently developed OFURanalyzer (OFUR ? online-analysis of mineral deposits) provides possibilities for exploration and visualization of deposit models in real-time and thus creates an opportunity for innovative applications, such as contactless, continuous quality control of minerals throughout the extraction process. A major challenge in the execution of this project was the necessity to develop a laser system that could withstand rough mining environments dominated by dust, shocks, vibration and therefore would be suited to operate under such conditions.

Oct 1, 2009

By Kjell Winther

"Hydralift Scanmec introduced early in the eighties a new and different mill design for very large grinding mills. The design described has actually no size limitation upwards and is so far suggested with motor power up to 40 MW. The mill is furnished with gearless ring motor drive transmission. It is totally fabricated, without heavy castings. The first installation, an 8, 1 MW ball mill dia. 6,5 m x 9,65 m length, has been in continous operation in 13 years without problems. Total grinding costs has been reduced with 3 0% compared to traditional smaller mills. Reductions has been achieved in maintenance cost, power consumption, liner wear and grinding media consumption.So far 3 ball mills of the described design are delivered and in operation, one grinding Iron ore and two grinding Nickel ore.IntroductionThe design of mills for mineral ore dressing has basically been unchanged since grinding in mills started some I 00 years ago, in spite of the fact that mills have grown larger and larger. This has resulted in structural and mechanical problems, causing expensive failures and loss of production.Hydralift Scanmec engineers were designing mills for more than 20 years according to the old «rules». As they experienced interest for an increase in the mill size at the time when reports about failing mills were published, they started analyzing the different mill parts to find new solutions. One goal was to only use elements from proven technology in the new design. Two key items were ring motor (wrap around motor)(Isch et al. 1977, Meintrup and Klein 1982, Ranze 1983) and large diameter pad bearings (wrap around bearings)(Fuller 1984), both acknowledged from other industries."

Jan 1, 1995

By Trevor Yeomans

"NVI Mining’s Myra Falls Operation is a forty year old underground mining operation feeding a 4000 mtpd concentrator.The current Mill, built in 1985, was designed to process a large massive sulphide ore-body. This ore-body, known as the “HW”, contains about 50% pyrite. Value minerals are chalcopyrite, and sphalerite, with precious metals occurring in all mineral types.By 1997, mining of a new ore-body, known as “Battle-Gap” commenced. Mineralogically complex, the new orebody contains about 15% pyrite, copper minerals including primary chalcopyrite, secondary bornite, chalcocite and tennantite, combined with increased galena and sphalerite.Flotation performance generally decreased with increasing amounts of Battle-Gap ore types, with both copper concentrate quality (increased lead and zinc content) and copper recoveries being affected.Following significant metallurgical testwork, a new fully sequential copper-lead-zinc flotation flowsheet and reagent scheme was developed.This sequential flowsheet was progressively installed and commissioned during 2006.Copper concentrate lead and zinc smelter penalty contents have been reduced by some 40%, whilst increasing copper recovery by 10%.INTRODUCTIONNVI Mining operates the Myra Falls Operation near Campbell River on Vancouver Island, BC. The complex has been in operation since 1966 with mining being predominantly underground. One unique feature of Myra Falls is that the mine operates within a BC Provincial Park.In 1985, a new large massive sulphide ore-body (HW) had been defined, and metallurgically tested. A new concentrator was built based upon this massive pyrite, chalcopyrite, and sphalerite mineralization producing copper and zinc concentrates by conventional flotation methods."

Jan 1, 2008

By James A. Finch, Stéphanie Somot

"The self-heating facility developed at the Noranda Technology Centre [Rosenblum and coworkers, 2001; 1995] has now been established in the Department of Mining, Metals and Materials Engineering at McGill University. A research program into mechanisms has been initiated (with support now from four industrial partners under Camiro). The first investigation is into the role of pyrrhotite (Po), the most commonly suspected mineral to trigger self-heating. Following a standard experimental protocol, self-heating was assessed on samples of Po mixed with sand as an inert material. With increasing Po content, self heating progressively increased but, interestingly, the samples visually appeared less and less oxidized. A high Po content, it was hypothesized, may give a more reducing environment favouring formation of H2S. The presence of this gas could be significant as it has a high exothermic heat of reaction with oxygen. The system was modified to test the hypothesis by including copper pieces and copper sulphate to react with (and therefore reveal) the gas as copper sulphide. Evidence is presented in support of H2S production, which to our knowledge has not been shown before and introduces a potentially important avenue of investigation into self-heating mechanisms.INTRODUCTIONSelf-heating of sulphide minerals poses potential environmental and safety hazards in mining of ores, and storage and transport of concentrates. While some conditions are known to be critical, the reactions remain poorly understood making self-heating difficult to predict and control.A major advance in measurement was introduced by Rosenblum and co-workers [Rosenblum et al., 2001; Rosenblum and Spira 1995]. A self-heating assessment method was developed and applied to various sulphide-bearing materials The method is based upon automated calorimetric cells with data acquisition, now available to McGill researchers and which have been used for the study reported here."

Jan 1, 2006

"Increasing demand for timely and accurate information about flotation plant performance requires metal accountants to increase the scope and reporting frequency of plant production. This trend has brought in-process inventory estimation at the forefront of metal accounting issues. Such significant in-process inventories can be locked in diverse process equipment (bins, holding tanks, flotation cells, thickeners, pipeline, etc.) or in stockpiles (ore, concentrates, tailings, etc.). Practice has shown that boldly ignoring these in-process inventories or the errors associated with their estimation lead to unreliable metal balances thereby creating confusion in plant production planning and operational performance assessment. To this extent, the characteristics (physical bounds, spatial heterogeneity and residence time) as well as the available measurements (volume, density, humidity, mass, composition, etc.) of each unit/section found in a generic flotation plant are jointly reviewed with respect to the particular metal accounting issues they present. The daily and monthly metal accounting tasks are then reviewed together with possible methods for obtaining reliable inventory estimates including different procedures for end-of month reconciliation.INTRODUCTION Most of the cost reduction initiatives of the mining industry aim at improving capital efficiency and asset utilization. Among the possible paths through which these goals can be achieved are mine-to-metal optimization, real-time plantwide process control (Hodouin, 2011) and knowledge sharing databases (Bascur & Linares, 2006). However, the successful implementation and subsequent monitoring will ineluctably results in an increased demand for timely and accurate information. This more than often requires metal accountants to increase the scope and reporting frequency of plant metal production. A striking example of such scope expansion is the Minas-Rio iron ore project in Brazil (Anglo American, 2013) having a pipeline route of 525 km between the concentrator and the concentrate shipping area. Several other mining companies have also set an increased frequency for their key performance indicators thereby shrinking the metal accounting period from monthly to weekly and daily. Those concurrent trends have brought in-process inventory estimation at the forefront of metal accounting issues. Indeed, as illustrated in Figure 1, improving trading reactivity requires improvements in production planning which strongly impacts the requirements for reliable metallurgical accounting. Furthermore, practice has shown that boldly ignoring significant in-process inventories or the errors associated with their estimation can lead to unreliable metal balances. In other words, since metal balances are the cornerstones of metal accounting, some of the risks associated with important business decisions are linked to errors associated with in-process inventory measurements."

Jan 1, 2014

By Luc Harnois, Gabriel Voicu, Marc Bardoux, Robert Crépeau

"Abstract-Detailed petrographical and geochemical studies have been carried out on the igneous and sedimentary rocks in the Omai area, part of the Paleoproterozoic Barama-Mazaruni greenstone belt, Guyana. The stratigraphic succession at Omai begins with basalts, associated with mafic-ultramafic intrusives and poorly-sorted conglomerates; these are overlain by andesites and quartzfeldspar porphyries, with pelites and tuffaceous sediments at the top. The volcanic-sedimentary succession was intruded by a quartz-monzodioritic stock (Omai stock) and granophyric rhyolite dikes. Several generations of mafic dikes were intruded discontinuously from the Mesoproterozoic to the Permo-Triassic. Volcanic rocks range in composition from subalkaline basalt to high-silica rhyolites, with a gap between 60% to 70% SiO2, which suggests the suite is bimodal. Major, trace, and rare earth element criteria were used to subdivide the rocks into tholeiitic and calc-alkaline types. The tholeiitic rocks are characterized by flat to moderately sloping chondrite-normalized REE patterns. On the basis of immobile trace-element ratios, the tholeiitic mafic rocks from Omai have characteristics of immature intra-oceanic island arcs, or of E-MORB basalts affected by a strong arc signature, as is commonly reported for back-arc basin basalts. The andesites, quartz-feldspar porphyries, rhyolites and quartz monzodioritic stock are calc-alkaline, with strongly sloping REE patterns, enrichments in the large-ion lithophile elements, and depletions in the heavy REE and high-field-strength elements, features which are typical of more mature island-arc settings.At Omai, two types of gold-bearing veins can be distinguished: vein sets (± stockworks) and tension veins, both post-dating the regional metamorphic peak at the level they were emplaced. The relationship between the gold mineralization and its host lithologies does not seem to be genetic. Rather, the emplacement of mineralization was strongly influenced by the rheological contrasts between the intrusive/subvolcanic bodies and the volcanic/sedimentary country rocks. These contrasts helped to focus the regional stress upon the more competent intrusive subvolcanic bodies, resulting in brittle fracturing, and therefore in greatly enhanced permeability to hydrothermal fluids. The Omai gold mineralization can be classified as late tectonic, with its emplacement controlled by the last brittle to brittle-ductile stages of the Trans-Amazonian orogeny."

Jan 1, 1997

By Gabriel Voicu, Harnois Luc, Marc Bardoux, Robert Crépeau

"Detailed petrographical and geochemical studies have been carried out on the igneous and sedimentary rocks in the Omai area, part of the Paleoproterozoic Barama-Mazaruni greenstonebelt, Guyana. The stratigraphic succession at Omai begins with basalts, associated with ma?c-ultrama?c intrusives and poorly-sorted conglomerates; these are overlain by andesites and quartz-feldspar porphyries, with pelites and tuffaceous sediments at the top. The volcanic-sedimentary succession was intruded by a quartz-monzodioritic stock (Omai stock) and granophyric rhyolitedikes. Several generations of ma?c dikes were intruded discontinuously from the Mesoproterozoicto the Permo-Triassic. Volcanic rocks range in composition from subalkaline basalt to high-silicarhyolites, with a gap between 60% to 70% SiO2, which suggests the suite is bimodal. Major, trace, and rare earth element criteria were used to subdivide the rocks into tholeiitic and calc-alkaline types. The tholeiitic rocks are characterized by ?at to moderately sloping chondrite-normalized REE patterns. On the basis of immobile trace-element ratios, the tholeiitic ma?c rocks from Omai have characteristics of immature intra-oceanic island arcs, or of E-MORB basalts affected by a strong arcsignature, as is commonly reported for back-arc basin basalts. The andesites, quartz-feldspar porphyries, rhyolites and quartz monzodioritic stock are calc-alkaline, with strongly sloping REE pat-terns, enrichments in the large-ion lithophile elements, and depletions in the heavy REE and high-?eld-strength elements, features which are typical of more mature island-arc settings.At Omai, two types of gold-bearing veins can be distinguished: vein sets (± stockworks) and tension veins, both post-dating the regional metamorphic peak at the level they were emplaced. The relationship between the gold mineralization and its host lithologies does not seem to be genetic. Rather, the emplacement of mineralization was strongly in?uenced by the rheological contrasts between the intrusive/subvolcanic bodies and the volcanic/sedimentary country rocks. These con-trasts helped to focus the regional stress upon the more competent intrusive subvolcanic bodies,resulting in brittle fracturing, and therefore in greatly enhanced permeability to hydrothermal ?uids.The Omai gold mineralization can be classi?ed as late tectonic, with its emplacement controlled by the last brittle to brittle-ductile stages of the Trans-Amazonian orogeny."

Jan 1, 1997

By M. W. Grabinsky

Better in situ performance data is required in order to advance the rational geomechanical design of cemented paste backfill systems. A few in situ test programs have been conducted, but these have suffered from too few measurement locations within the stope and have not used enough different types of transducers to fully capture the information of significance. In this paper the important geomechanical design aspects are listed, the underlying physical phenomena are described, and some previous in situ measurement efforts are reviewed. A new approach to in situ measurement campaigns is then described including measurement techniques, locations, and the logistical aspects of mobilizing transducers in an active mining environment. A work-in-progress is used to illustrate the principles and concepts involved.

May 1, 2007

By Ernest Baafi

A simulation model RoadSIM using the ARENA modelling system has been developed to evaluate roadway development options for a given development panel configuration. The RoadSIM simulation system has provisions for variability/randomness in operations including cutting and loading at the face, tramming and discharge of coal to the boot end and availability of equipment. The modelling system provides a means for assessing the operational limitations of roadway development practices at a particular coalmine. It is a ?what if? tool that allows a range of equipment, configurations and operating practices to be assessed in terms of achievable advance rates and equipment utilisation. Output from the system is in the form of a dynamic visualisation as well as summary reports and detailed logs of operations over time.

Oct 1, 2009

By David M. R. Stone

Underground mining in the gold industry is gaining popularity in Nevada, and with it the use of cemented rockfill is becoming mainstream. Even with today?s high metal prices, however, mining companies are very sensitive to the margins they realize, and are constantly looking for ways to reduce costs or improve efficiencies. Given that the backfill is one of the largest cost centers in underground mining, mines are constantly under pressure to reduce backfill costs. This paper will present an overview of the factors that impact cemented rockfill quality in Nevada mines based on the authors many years of consulting experience. Cemented rockfill quality can be linked directly to binder consumption, hence programs aimed at improving quality generally result in lower binder costs, better performance in the fill (hence less dilution), and improved safety. The paper will conclude with the key elements of a comprehensive program of backfill quality assessments and backfill QA programs. Comparative laboratory and minesite data from a number of operating and proposed mines will be presented.

May 1, 2007