Search Documents

By Gordon King

The City of Atlanta Water Department required the construction of a two sludge tanks and a wet well at the existing Chattahoochee Water Treatment Plant. Western Summit won a design build contract to build the project and proceeded to evaluate the wet well size options, and construction procedures. The final design required the construction of a 1 million gallon tank. The proximity of the underground tank to adjacent roads and existing plant structures ruled out laying back the excavation. As a result a tied back sheet pile retaining wall was initially proposed.

Jan 1, 2003

By A. F. van Weele

In general cast-in place piles will have an irregular pile shape. However, it is possible that these irregularities are so large that they may lead to pile deficiencies. It is very rarely possible to examine the pile foundations visually. Also the performance of a static or dynamic load test on each individual pile is not practical and much too expensive. This is the reason why pile integrity tests have been developed: to reduce the risk of inadequate pile foundations by performing a simple test. Pile integrity tests are non destructive tests which are carried out after a pile has been installed. Over the years a number of techniques have been developed of which the most important techniques are briefly described in this paper. Of all pile integrity testing methods, Sonic Integrity Testing is the most widely used method in western Europe. This method has been developed by TNO some 15 years ago. Since then the method has been improved, largely due to advances in micro-processing. A major improvement was made by the introduction of digital signal processing techniques. This made the Sonic Integrity Testing method more accurate (smaller defects can be detected), faster (more than 200 piles can be tested on a single working-day) and more reliable (the results are easier to interprete). A few cases will be presented which will show the usefulness of the Sonic Integrity Testing method. In one of these cases, a helpful tool for interpretation of the results is explained: the Sonic Integrity Testing Simulation program TNOWAVE. Notwithstanding the fact that Sonic Integrity Testing is a powerful method, it has also some strict limitations. These will be discussed at the end of the paper.

Jan 1, 1987

By Wolfgang G. Brunner

A 3800 m long temporary water-retaining dike has been constructed under extreme conditions in the harsh northern climate to enable two of the kimberiite pipes at the Diavik Diamond Project reserve to be mined using open pits. The Diavik Diamond Project is located on East Island at Lac de Gras in Canada's Northwest Territories, approximately 200 kilometres south of the Arctic Circle. The dike which has been constructed in up to 25 m deep water from crushed granite quarried from the site projects into Lac de Gras encircles the first two of the kimberiite pipes to be mined. An 800 mm wide diaphragm cut­off wall constructed of bentonite, cement and crushed rock, totalling 33,000 m2, and a two-phase jet grouted curtain wail at its base, totalling 8,400 m2, have been installed through the dike and underlying till foundation into bedrock. The cut-off is designed to minimise water seepage from Lac de Gras through the dike. In order to ensure that the dike had adequate internal stability and diaphragm wall construction could proceed safely, the crushed rock fill material dumped into the lake was first compacted by TR 75 deep vibrators. In 2000, Bauer Maschinen GmbH of Schrobenhausen, Germany were awarded the contract for the supply of all specialist foundation equipment required on site and for providing technical support to the Canadian main contractor Lac-de-Gras-Construction throughout the construction of the cut-off walls during 2001 and 2002. Installation of the cut-off walls was completed in July 2002, three weeks ahead of schedule, and dewatering of the inner dike areas commenced just 5 days later and has continued throughout August and September. After completion of extensive testing of the diamond recovery plant, the mine is scheduled to go into full open pit production in February 2003.

Jan 1, 2003

By S. Bang

In recent years, suction piles and suction anchors have been used as underwater foundations for various offshore structures. They have been proven very versatile, effective, and environmentally friendly. This paper describes the load resisting mechanism, installation, and design of suction piles and suction anchors. Also included are brief descriptions of three offshore structures that have recently been constructed using suction piles and suction anchors. They include: a new breakwater system utilizing gravity-type concrete caisson superstructure on top of concrete suction piles; a floating breakwater system utilizing embedded suction anchors; and a foundation system utilizing suction piles for temporary mooring of underwater tunnel elements.

Jan 1, 2009

By Frederic Masse

With widespread acceptance in the market place, many engineers are choosing ground improvement techniques to provide suitable foundation subgrade at sites that would have traditionally required deep foundations. This paper discusses the Controlled Modulus Columns (CMC) ground improvement technique and some case histories highlighting the use of this technique for retail development sites. CMC are a sustainable and cost-effective ground improvement technology that transmit load from the foundation to a lower bearing stratum through a composite CMC/soil matrix. The CMC installation is also an attractive option from an environmental perspective because it utilizes reverse flight augers, which displace the soil laterally. This installation technique achieves two goals: it densifies the soil around the CMC, which improves load transfer into the element and avoids spoil and its disposal. Through the introduction of two cases histories, we will present the key benefits of the CMC technology. Each case history will clearly illustrate how a CMC solution can reduce the overall cost of a project when compared to a more traditional type of deep foundations. They will also show how the use of CMCs has benefits that relate to the overall sustainability of the project. While CMCs are an attractive financial and sustainable option, they have also demonstrated that the performance of the system is comparable to that of deep pile foundations. Because CMCs are a relatively new technology many potential users are not aware of its benefits. While we discuss the use of CMCs to support buildings in this paper, CMCs also have been used for a variety of other applications including foundations for tanks, mechanically stabilized earth (MSE) walls, and embankments

Jan 1, 2011

By Arturo Ressi di Cervia

From the times when men in lacustrine environments drove wooden piles into the mud to elevate their dwellings, until the beginning of the twentieth century builders reacted to the conditions found in the location of their proposed structures by attempting to distribute their loads in ways that could be supported by the foundation's soils; or, if those were unsuitable, by moving the structure, whenever possible. While many major structures were built on stable ground (the pyramids were founded on rock), others were built on [ ]

Jan 1, 2000

By Ekhlaq A. Khan

"The new third Bridge over Narmada River at Bharuch which was recently completed is characterized by some aesthetically appealing elevations of the pylon and large size of the deck. This paper gives an insight to design and construction technique adopted for foundation construction of Extra-dosed span - 3 rd Narmada Bridge at Bharuch over river Narmada, Gujarat. Site being located in intertidal zone had its unique geological characteristics and own set of difficulties during construction.INTRODUCTIONThe Indian subcontinent offers diverse subsoil conditions. With current modern and future trend of long span bridges the substructure design often demands large size foundations. The foundation of theses bridges are usually deep and large in size. The execution of such foundations in maritime environments often involves important temporary works, in order to provide a safe workplace, comply with environmental requirements and achieve high quality standards.Often Pile foundations are preferred solution now a days, but due to various statutory and environmental regulations their construction poses a challenge. With better equipment and corresponding quality control, construction of large diameter pile foundation has emerged as a faster and reliable option.OVER VIEW OF THE PROJECTThe first two lane bridge on NH-8 (Vadodra – Mumbai) known as Sardar Bridge was constructed in 1977, subsequently an additional two lane bridge was constructed in 1999-2000, 29 m downstream of the first. In view of rising volume of traffic and as part of upgradation of NH8, National Highways Authority of India (NHAI) proposed to construct 3rd new 4 Lane Bridge 100 m downstream of 2nd Narmada Bridge, based on Central Water and Power research Institute (CWPRS) study and recommendation.The general layout (fig. 1) of the 3rd Narmada bridge has 8 spans of 144 m and 2 spans of 96 m with total length of 1344 m, supported by132 nos. of 1.5 m diameter piles of about 50 m depth. The substructure has leaning “Y” shaped lower pylon of height 30 m together with cast in situ pier diaphragm. The piles are of M40 and superstructure & pylon of M50 grade of concrete."

Jan 1, 2017

By Matthias Pulsfort, Markus Herten, Rolf Breitenbücher, Claudia Fierenkothen

"Secant bored pile walls are frequently used as retaining walls in watertight excavations to cut off ground water aquifers and are subsequently exposed to ground water pressure loading in addition to earth pressure loads. To avoid extra loading from ground water pressure in soils with limited permeability, it can be useful to arrange drainage windows within secant bored pile walls by means of single primary piles filled with porous concrete without reinforcement cages, which usually have to be placed within casings in submerged conditions. This concrete may serve as a horizontal arch between the reinforced secondary piles, but it must however enable vertical draining between load carrying construction beams and the bottom of the excavated pit. In the present submission, the results of several material tests with different mix designs of porous concrete with certain admixtures are presented together with first and important experiences with a wellsuited placement technique for porous concrete casings in small- and large-scale laboratory tests. It can be shown that the usual placement technique of employing a tremie pipe is not suited for this type of unsaturated concrete. Instead, pouring with a particular kind of cone and an open conductor pipe has proven successful.Additionally, special testing methods are currently developed for judging the suitability of the desired concrete mix design in preparation for an upcoming real-scale experimental pile installation in Germany.1. INTRODUCTIONRetaining walls are often built as secant bored pile walls in order to cut off aquifers saturated with groundwater against deep building pits. In soil types with relatively low permeability, however, seepage flow may be permitted, because the quantity of groundwater to be pumped is limited, and the range of influence due to dewatering is not reaching far. Thus, the hydrostatic water pressure on the retaining wall can be considerably reduced, leading to a more economic design (see Fig. 1).In unsaturated soils, the dewatering effect can be achieved by means of porous pervious concrete with a uniform grainsize distribution of aggregates typically placed in a borehole under dry conditions. With regard to the use of porous concrete to be placed at the ground surface in road pavement applications, experience is sufficiently available as shown, for instance, by Neithalath et el. (2010). However placing the porous concrete in a bored pile using a tremie pipe under submerged conditions is a challenge and a completely new approach, because there is a considerable risk of segregation of the fresh concrete, separating the cement lime paste from the aggregates when in contact with water and leaving only neat gravel on the one hand as well as a tight cemented area at the bottom of the pile on the other hand. If this concrete placement is successful, additional dewatering by means of extra wells behind the retaining wall can be avoided. Of course the seepage flow in the adjacent soil needs to be regarded seriously."

Jan 1, 2017

By Richard K. Sandaas

Start Date: April 4, 1988 Completion Date: Dec. 29, 1989 Contractor: SCI Contractors Past and present transportation centers will come together at International District Station, located at the south entrance to the tunnel next to the turn-of-the-century Union Station train depot. The area will bustle once again with activity as commuters and visitors converge on the modern transit station at the edge of Seattle's International District. Buses coming from south Interstate 5 and Interstate 90 will enter the tunnel through this station. [ ] International District Station is an open-air station, 1,060 feet long and 82 feet wide (about 15,400 cubic yards of concrete were used to build the station). A concrete lid over the southern portion of the station staging area is held in place by 131 support piles. The station will include entrances on Jackson Street and King Street. Union Pacific Realty is planning to build an office and retail complex upon the lid. The station also has an international flair. Symbols of the Chinese zodiac will be etched into the station plaza floor. The station platform walls will be lined with large steel panels embellished with designs in origami?a Japanese folded paper art form. [ ]

Jan 1, 1990

By Lin Daoyi

In this paper, we have adopted the high pressure jet-grouting curtains to seal the sea-water, and to consolidate the wall of the well for deep foundation diteh, make a pladge of building and construction of deep foundation was primarily on progress without water. This paper, we have been given a test for pumping water under mainly the circumtances of sealing condition and to report in advance the capacity of seawater seeping into the gam curtains in the process of building and construction of deep foundation.

Jan 1, 1991

By Jay A. Berger

Nondestructive testing of deep foundations for integrity problems made great strides in the late 1980's. Inexpensive portable computers have allowed the immediate and rapid processing of field measured acceleration records which can provide insight into the relative structural integrity of a previously installed foundation member. Although the gathering, processing and displaying of the data is now straightforward, interpretation remains at times rather challenging. This paper provides a brief introduction into the theoretical basis for data interpretation and the hardware necessary for data acquisition. Five case studies are discussed which demonstrate the varied applications of low strain integrity testing of deep foundations and the efficiency at which they are completed. BACKGROUND One dimensional wave mechanics, when applied to a linear elastic pile with a length that is an order of magnitude greater than its width, provides a straightforward basis for the interpretation of motion measurements made at a pile top. When impacted, a stress wave travels through the pile at a wave speed, c, which is a function of the elastic modulus, E, and mass density p (i.e., E=pc2). The applied load F, and particle velocity v, at a point are related by the equation F=Zv. For a cross-sectional area A, the proportionality constant Z is equal to EA/c. Because Z is a measure of the pile's resistance to change in velocity it is called the pile impedance.

Jan 1, 1990

By G. T. Hong

A numerical model for use in design is developed to predict the stresses and axial and bending displacements in a drilled pier in expansive soils. The prediction is based on the horizontal swelling pressures and uplift forces which act on the side of the drilled pier. The exponential suction envelope with the depth within the moisture active zone is estimated based upon the equilibrium suction, moisture diffusion coefficients obtained from laboratory tests, and minimum suction at the ground surface of the site based on field conditions. The volume change of soil is based on suction variations, soil properties, overburden pressures, crack influences, and the relationship between moisture contents and suctions. Considering the movement active and anchor zones on a soil-pile system in expansive soils, horizontal swelling pressures are formulated using the shear strength of an unsaturated soil and the Mohr?s circle and failure envelope. The movement active zone has two sub-zones in which horizontal swelling pressures are attributed to passive earth pressure failure and suction change in the upper and lower sub-zones, respectively. Horizontal swelling pressures which occur in the anchor zone are assumed to be in the at rest condition. The shear stress generated on the vertical surface of a drilled pier is supported by the nonlinear curves of load transfer versus relative displacement. The axial behavior and lateral bending of the pier in expansive soils are simulated using a beam column approach. The computed axial and bending displacements and stresses are used to provide structural design of the pier. Figures of computed results for typical cases are presented.

Jan 1, 2007

By Ke Yang

Drilled shafts are widely used as foundation system for sound walls to resist lateral loads. The design method based on the ultimate lateral capacity, such as Broms method, is often used for sound wall foundation design. Allowable Stress Design (ASD) is currently used for deep foundation design. However, by October 2007, all states Department of Transportations are required to use the Load Resistance Factor Design (LRFD) approach for the design of foundation in highway projects. There is a need to develop a calibrated resistance factor in LRFD lateral design of drilled shafts supporting sound barrier walls. This paper provides resistance factors for design of laterally loaded drilled shafts supporting sound walls using Broms method based on the study using reliability based method and fitting to ASD method. Additionally, the resistance factors for static lateral load tests are recommended. Furthermore, a methodology to update the resistance factors using Bayesian approach by incorporating the on-site full-scale lateral load test results is presented. To illustrate the Bayesian update methodology, two lateral load tests in Colorado were employed to develop the updated resistance factors.

Jan 1, 2007

By Bret N. Lingwall, Byron Foster

The problem of reliable extreme event modeling of large diameter piles under enormous structural or kinematic loads has gained more attention in recent years. In particular, the soil response around the foundation and impacts to buried adjacent infrastructure has gained interest. One of the principal shortcomings with analysis of large diameter pile foundations under extreme event lateral loading is the reliance on conventional beam on elastic foundation methods, which do not model the soil field response around the pile. These methods are limited for large displacement problems, and for large diameter piles. However, the fundamental interactions between steel and concrete, and structure to soil are difficult to constrain, especially in large strain problems where the structural elements become inelastic. The non-linear interaction of the structural materials and soil is desirable so that assessment of stress changes in the field and effects on adjacent facilities can be modeled. A numerical modeling methodology that addresses these shortcomings has been developed. This method utilizes the interaction of brittle concrete with discrete steel reinforcing and casing in a robust manner capturing inelastic non-linearity in both soil and structure. This paper presents a comparison study of the method, wherein three different validation studies were made to data from full scale laterally loaded pile testing. INTRODUCTION Extreme event lateral loading of deep foundations comes in many forms including earthquakes, landsliding, tsunamis, hurricanes, surface fault rupture, liquefaction induced lateral spreads and many more. These extreme events induce loads on foundations far greater than service or strength loads. Perhaps the most dangerous extreme event loads are those of large soil displacements such as landslides, lateral spreads, and surface fault rupture, wherein the soil surrounding the foundations can move laterally 100 mm to 3 m! In these extreme event loading scenarios, small diameter foundations are pushed past their limits and many engineers prefer large diameter deep foundations for these situations. These deep foundations of diameter 900 mm or greater may be auger cast in place piles, cast in drilled hole piles, cast in steel shell piles, cased or uncased drilled shafts, bored precast piles, etc. For convenience in this paper, large diameter deep foundations will be referred to as Large Diameter Shafts (LDS). In LDS, steel may or may not used as a shell around the perimeter of the concrete and/or as internal tensile reinforcement. The interaction between brittle concrete and ductile steel within and/or along the perimeter of the LDS is critical to understanding the non-linear inelastic behavior of LDS for problems of large lateral displacements from extreme events.

Jan 1, 2018

By Federico Pagliacci, Marco Chiarabelli, Salvatore Miranda

The paper describes the adopted technologies and performance controls related to a special geotechnical engineering solution provided within the scope of the Galataport Project, in Istanbul, Turkey. The scheme is the one applied to the new quay of Salipazari, which is a combination of retaining structure and ground improvement, formed by a combi-wall, a reinforced concrete diaphragm wall and a soil improvement by deep soil mixing (Turbojet). The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high profile Project. The results of the in-situ and laboratory tests carried out on the improved soil are also presented. Main discussed points are: • History of Galataport and main Project details. • Design principle and soil condition for the new quay of Salipazari. • Difficulties encountered during execution of DSM. • Preliminary field trial tests conducted to establish the operational parameters, with relevant in-situ and laboratory tests executed. • Preliminary tests on material used for DSM (seawater and CEM IV SR). • Electronic equipment mounted on the rig, which allows the automatic execution of DSM columns. • Final QA/QC tests conducted to verify the performance of DSM, mainly consisting in: coring with relevant laboratory tests on samples (UCS + Es), seismic refraction tomography and seismic cross hole tomography. Correlations between UCS and Es, and between Es and Edyn are also presented. • A cross section of the executed treatment could be inspected on site during excavation. Photos and considerations are also presented.

Jan 1, 2018

By Alan B. Wagner

Data from seven instrumented pile load tests in Milwaukee, Wisconsin and two other instrumented load tests reported in the literature, one in Evanston, Illinois and one in Houston, Texas were reviewed. The data were for pipe piles having diameters from 9-5/8 inches to 18 inches, driven to depths between 36 and 96 feet. These data were used to develop a relationship between effective vertical stress and unit side friction and unit end bearing. These relationships were based on readily measured soil parameters, undrained shear strength, Cu, and Standard Penetration Test (SPT) values. This Beta (ß) and Nt approach and four other methods were then used to calculate the bearing capacity of the nine cases analyzed. The results from each of the methods are compared with the measured results.

Jan 1, 1991

By D. E. Sherwood

Recent developments in high torque hydraulic rotary rigs has lead to the construction of secant bored pile walls by rotary drilling methods in circumstances where earlier methods were difficult and in some cases impossible. The evolution of secant bored pile wall construction is described including classical, rotary drilled and continuous flight auger construction methods. The paper then details the restraints which have been created in recent inner city redevelopment, many of which were not relevant in the early days of the technique. Typical examples of walls are presented to show the adapatability and advantages of the secant bored pile wall method. A number of in-situ retaining wall construction techniques are then compared in detail with regard to relative cost, technical quality and practicality.

Jan 1, 1989

By Cristhian C. Mendoza, Renato da Cunha, Bernardo Caicedo, Max Barbosa

"Abstract This paper shows that a raft alone is not sufficiently appropriate to address the uncertainty of underlying soil variability; therefore, a piled raft system is a better option for mitigating such uncertainty. To study the variability of soil, the behavior of the Piled-Raft Foundation was analyzed with a type of self-drilling micropiles: the ""Alluvial Anker"" (common name for this pile type in Brasilia city). These micropiles have been used in the city and have the advantage that the drill pipe also serves as reinforcement. The studied parameters belong to an elastoplastic constitutive model for strain-stress analysis of soil; variability of these parameters can be intrinsic and/or epistemic. Simulations were performed for a hypothetical Piled-Raft Foundation subjected to vertical loading using the random finite element method. The average parameters of the constitutive model were obtained through laboratory tests. The simulations of the load test were compared with results of a real scale experimental test conducted exclusively for this work in the field. It is analyzed the relative importance of the variability of some geomechanical parameters and their variation with depth is considered. In addition, it is discussed a comparison between the uncertainty of the geomechanical parameters and the uncertainty of the results of the vertical loading test. Finally, this paper shows that a decrease of the safety factor may occur when taking into account the variability of the parameters.IntroductionBrasilia is located in a highly weathered residual tropical soil (lateritic & latossol on pedogenetic concepts). This soil presents high content of alumina and iron due to the lixiviation process of the upper layers. As a consequence, the cemented structure is highly unstable and it can generate strong changes of volume (i.e. collapse) due to changes in both moisture and state of stresses. Therefore, a greater understanding of the construction of Piled-Raft Foundation systems on this particular soil conditions is needed – especially because it covers more than 80% of the surface area of the Brazilian Federal District.Thereafter, this work investigates the influence of the variability of the soil parameters over the uncertainty of the Piled-Raft Foundation design. The studied parameters belong to an elastoplastic constitutive model for strain-stress analysis of soils. The simulations were performed for two hypothetical Piled-Raft Foundations subjected to vertical loading by using the stochastic finite element method. The results were compared to real load tests in Piled-Rafts with “Alluvial Anker” pile types."

Jan 1, 2014

By Giuliana A. Zelada

This paper reports on a study of 43 compression load tests (five fully instrumented) and ten pullout tests of auger cast-in-place (ACIP) piles in sand. Eight design methods reported in the literature were used to predict the measured pile capacities. Ultimate load capacities of the ACIP load tests were determined using two different definitions of ultimate capacity and compared with predictions. Load transfer behavior was determined from a study of the fully instrumented pile tests and compared to predicted values. Recommendations are made regarding the design approach most appropriate for these foundations and the best procedure for estimating ultimate capacity from pile load tests.

Jan 1, 2000

By Arturo Ressi di Cervia

The utilization of diaphragm wall construction in Hong Kong began in 1974 with the construction of the New World Center, the first diaphragm wall job built in the British Colony. That landmark job of which I am presenting a few slides and a schematic description, embodied all of the difficulties and problems which are encountered in the difficult geology of Hong Kong. A small rocky island in the South China Sea, Hong Kong provides one of the finest natural harbors in the world. It is its splendid harbor, coupled with the enterprising attitude of the Hong Kong Chinese and the laissez-fair attitude of the British government which has resulted in the explosive growth of this speck of land soon to revert to the political control of mainland China.

Jan 1, 1993