Search Documents

By Aly M. Mohammad

The 12th and 14th Street Viaducts, which carry Route 139, are located west of the Holland Tunnel in Jersey City, New Jersey. The two viaducts, provide access to and from the Holland Tunnel (which connects New York City and New Jersey) and carry upwards of 50,0000 vehicles per day from Jersey City and New York City to points west. The New Jersey Department of Transportation (NJDOT) selected AECOM to perform design services including rehabilitation and seismic retrofit for the 12th Street and 14th Street Viaducts while maintaining traffic at all times. Building a new parallel bridge just north of the 14th Street Viaduct was essential in avoiding extremely costly traffic delays. Installation of the new foundation, in close proximity to the existing viaduct, required drilling through some of the existing timber piles supporting the bridge. As a result, the existing bridge was required to be reanalyzed for this new foundation configuration. This proposed structure consisted of 8 piers each supported on a single six (6) foot diameter drilled shaft. Currently this portion of the bridge structure has been constructed. The shafts were constructed with rock sockets that were five feet six inches (5?- 6??) in diameter and were extended 11.2 feet (3.4 meters) into rock. A 2300 ton Osterberg Load Test was performed on one production shaft to confirm the capacity of the shaft. The rock socket for the test shaft was in sandstone. This paper will present a description of the design methodology and construction methods adopted for the foundations. In addition, the paper will illustrate the Osterberg Load Test including: equipment used, number and locations of strain gages, and interpretation of results. Additionally, regarding the close proximity of the new foundation, the paper will present the type of equipment used to drill through the existing timber pile foundation while minimizing the impact on the integrity of the existing foundation. We will also present the method of analysis for analyzing the redistribution of load on the remaining piles. The results presented in this paper will assist the design engineer by providing a comparison between the geotechnical design assumptions and the actual measurements obtained by field measurements for this rock formation.

Jan 1, 2009

By George K. Burke

Jet grouting was first introduced into North America in the late 1970's, soon after the conception of the system in Japan. However, it was not until the mid-1980's that the technique began to gain acceptance through the renewed interest and efforts of specialist U.S. geotechnical contractors. Since this time, innovations by both American users and other users worldwide have further advanced the technology, with a corresponding increase in the range of practical applications. This paper discusses the evolution of jet grouting in North America, from simple single-fluid methods to more complex triple-fluid methods, to the energy-intensive double-fluid and SuperJet methods. Case histories, illustrating a variety of jet grouting methods and applications, are cited to support the newest United States applications.

Jan 1, 2002

By E. Mongilardi

The construction of large underground openings through cohesionless or weak cohesive soils and under the water table in particular, often requires a ground improvement to be done from the surface or ahead of the excavation face in tunnelling problems. To this purpose various injection procedures have been used in the past and new outstanding techniques have been developed recently, such as "jet-grouting", extending the feasibility range. The paper presents a review of basic principles and practical design criteria with particular reference to the newest trends of development. Case histories have been selected within the experience of specialist contractor Rodio Co. showing the variety of problems solved by manifold grouting procedures and layouts, in widely different soils ranging from the sandy-gravelly alluvia of Milan to the soft marine clays of Singapore.

Jan 1, 2010

By S. Kanai

Nodular piles is to be piles provided with several nodular projections along the pile shaft, as shown in Fig. 1. Nodular piles are usually installed through either driving method with hammer or preboring method. This paper presents that the bearing capacity installed through each method is considerably higher than that of cylindrical pile without nodules. This paper also proposes the statistically analyzed unique formulae of the bearing capacity of nodular piles.

Jan 1, 1989

By Mohammed Sakr

This paper presents the results of a full-scale axial compression and tension (uplift) testing program executed on large-capacity helical piles installed in very stiff to very hard clay till soils (i.e. cohesive soils). A total of ten tests including six axial compression tests and four tension (uplift) tests were carried out. The results of the axial compressive and tensile pile load tests and field monitoring of helical piles with either a single helix or double helix are presented in this paper. Helical piles are traditionally used to support light to medium loads (i.e. loads up to 500 kN or 56 tons). However the results of the present study confirmed that helical piles can support significantly higher axial compressive loads up to 2450 kN or 275 tons, which is about 5 times traditional design loads. The study also demonstrated the high tensile capacities of helical piles which was as high as 85% of their compressive capacity. Hence helical piles can provide a viable design option for foundations supporting relatively heavy loads.

Jan 1, 2012

By Yvone Franco Crosato

The dense population of Hong Kong requires the construction of tall buildings in reclaimed areas or perched on the slopes of the many hills. The large loads to be supported are carried by deep foundations. Many of those are bored piles, to rock, of diameters up to the 3.0 m. of today.

Jan 1, 2000

By Gerry Houlahan

The east span of the 3.5 km long SF-Oakland Bay Bridge is supported by different types of foundations along its span. Starting from the west, its first 460 m section comprising twin concrete box-girders is supported by sands and rock on Yerba Buena Island. A 620 m long steel suspension span then bridges a 25 m deep channel that is formed in sediments overlying rock. Twin concrete box girder structures, each 2.4 km long, complete the stretch over the remainder of San Francisco Bay to the engineered earth fill landing at its east end. For most of its length, the Skyway bridges water 3 to 10 m deep over soft surficial Young Bay Mud. The foundation types include spread footings with hold-downs, steel and concrete piles that are set in drilled rock sockets up to 3 m in diameter and 2.5 m diameter steel tubular piles driven to penetrations of up to 100 m. The design and construction-related considerations are presented. The different foundation types, influences of the site geology and earthquake demands on the substructures are discussed. The seismic motions of the bridge superstructures and substructures, as well as the depth-varying soil motions, influenced the foundation design. Together with performance-based design criteria, including post-earthquake footing displacement limits, these seismic demands influenced various aspects of the foundation design, including the use of battered and vertical piles.

Jan 1, 2005

By Chris G. Leach

"Abstract A seven storey Northbridge area of Perth, Western Australia presented residential apartment complex located in the an opportunity for a novel application of Cutter Soil Mix technology (CSM). The development included a two-level basement for car parking which covered the full site area. However, the basement was also required to extend under an existing single story heritage building. Soil conditions comprised 2m of fill overlying medium dense to dense sands that in turn were overlying a very stiff clay stratum at approximately 14-16m depth. The ground water table was located at a depth of approximately 1m below the natural surface level.A site boundary consisting of a reinforced CSM retention system and was designed and installed to allow the excavation to proceed to basement level. Two rows of temporary soils anchors or inclined struts were required to achieve this. A CSM support system for the heritage building was also designed and constructed to provide temporary support during excavation and permanent construction works. The brief for the contract works emphasised that it was vital that settlements of the heritage building be kept within strict limits.CSM is a relatively new introduction to the Australian construction market, using a modified trench cutter to mix a binder slurry with in situ soils, generally to form cut-off walls, retaining walls and soil improvement works. This project is understood to be first application of the CSM for underpinning work in Australia.This paper discusses the site background details leading to the decision by the client to adopt CSM technology, and the design and construction aspects to meet the challenges offered by this project.Introduction190 Newcastle St is a 7-level residential apartment complex located in the Northbridge area of Perth, Western Australia. The development includes a 2 level basement for car parking, which covers the full site area. The basement also extends under a single story heritage building, which remained in-situ throughout the building works.A site boundary retention system was required to allow the excavation to basement level to proceed. In addition, a support system for the heritage building was required to provide temporary support during excavation and permanent construction works."

Jan 1, 2014

By Alain E. Holeyman

After scoping out the objectives of this general report, the report reviews the three assigned main themes addressed by the papers submitted to the session: pile monitoring, testing, and data processing. It focuses on later developments and on issues requiring clarification, thereby identifying topics for potential discussion. Pile Monitoring does not bring much novelty, except for the integration of IT on construction sites. As far as testing, new developments focus on internal pile loading procedures while more confidence is being gained with dynamic and kinematic load tests. Significant advances are noted in the interpretation of data, where variability of results are coped with, loading rate effects are being better addressed, and more routine use of Finite element analyses are observed. Several many older problems remain while new issues emerge from more recent technologies and approaches.

Jan 1, 2006

By Jeffrey R. Hill

To extend the life of the Merchants Railroad Bridge crossing the Mississippi River in St. Louis, MO, the owner implemented a rehabilitation and reconstruction project. The Merchants Bridge provides a key link in the transcontinental railroad system. The bridge is of local importance to the Terminal Railroad Association ? providing a link between St Louis and a rail switching yard in Venice, IL. The intent of the bridge rehabilitation is to keep the Merchants Bridge in service, even though the bridge was originally constructed in the 1890?s. The project involved replacing the East and West approach deck truss spans with new deck girder spans. The rehabilitation program required construction of new concrete piers to support the new spans. In order to reduce the track down time to two, ten day single track shutdowns, the specifications required that all foundation and substructure work be completed while leaving the existing spans in place. The preliminary bridge design specified rock-socketed drilled shaft foundations. Drilled shafts proved to be challenging due to working from beneath the existing bridge, a high water table, utilities, a flood wall, and existing rail way lines. The micropile alternative was technically appropriate given the access limitations, shortened the foundation rehabilitation schedule by several weeks, and realized a significant cost savings to the Owner.

Jan 1, 2006

By Steni Stefani, Sanjay Dave

"This paper describes an innovative method, used for the first time in India, for the construction of a 1.0metre-thick positive plastic concrete cut-off wall (CoW) at the upstream toe of the dam at the Kishanganga Hydro-Electric Project in Jammu & Kashmir- India. The extremely difficult bouldery geology with an overburden laden with very hard Panjal Volcanics (quartz, feldspar, muscovite and chlorite minerals) boulders of up to 0.8m to 1.8 metres in size with UCS of up to 265 MPa and the requirement of socketing the CoW into the underlying hard bedrock (UCS 265 MPa) for 1.50m made the choice for the excavation methodology critically difficult. After having evaluated several other existing methods – including hydromill trenchers – the Civil Contractor Hindustan Construction Company, in agreement with its Foundations Engineering Consultant (Ricerca e Sviluppo – Cantieri e Gestioni) opted for a two-stage construction method: firstly, preliminary full-depth drilling and “surgical” blasting with full-length inclinometer checking of borehole verticality to ensure the exact location of rock fracturing and fragmentation coincided with the required position and that it was vertical, notwithstanding efficient trenching into the bedrock of a nominal 1m by 1.5m section; and, secondly, excavation by using heavy duty mechanical rope grabs made locally and developed by the Consultant in collaboration with the Contractor. The details of the methodology and the salient construction data is presented and commented for the 33-metre deep CoW installed at a working platform elevation of 2364.50 m above sea level in a very remote area.BACKGROUNDThe Kishanganga Hydro Electric Project (KGHEP) is a ROR (run-of-the-river) project is located on the Kishanganga River some 140kms North-West of Srinagar, capital of Jammu & Kashmir State of India, for generating 330MW of power in a 90% dependable annual year. The key components of the project are: Concrete Face Rockfill Dam (CFRD), Chute Spillway, Plastic Concrete Cut-off Wall (CoW), Head Race Tunnel (HRT), Surge Shaft (SS), Inclined Pressure Shaft (PS), underground Power House and Transformer Hall, Tail Race Tunnel (TRT).The Power House Site is accessible throughout the year from Srinagar while the remote Dam Site, with its tortuous road climbing the Rajdan Pass at 3556m (11,667 ft) above sea level and several 20-tonne capacity Bailey bridges removed prior to snowfall, remains inaccessible for around 4 months between mid-November to mid-May due to winter and heavy snowfall - the only access is by helicopter, weather permitting. Temperature at the Dam Site drops down to minus 27degrees Celsius during winter, therefore, careful planning from the beginning was most essential for the successful delivery of the Project.This paper deals with the Cut-Off Wall construction which was performed, for the first time in India, adopting a “Drilling and Surgical Blasting” method. However, this technology is not new and diaphragm wall excavation with the aid of drilling and blasting has already been done in some of the projects globally; namely:"

Jan 1, 2017

By Jesús E. Gómez

In the Summer of 2011, emergency repairs to the Jefferson Memorial North Plaza and Seawall were completed. These repairs were necessitated by settlement and lateral movement of the seawall and North Plaza which prompted the National Park Service (NPS) to initiate an investigation as to the possible causes of the movement, and commission a design for its mitigation. Information gathered from extensive instrumentation on site led to the design of a movement mitigation scheme that included demolition of the Ashlar Seawall and reconstruction of a new seawall. The new seawall foundation is an A-Wall consisting of vertical caissons and battered pipe piles connected to the seawall itself. The scheme provides resistance to future vertical and lateral movement of the North Plaza and the new seawall. Repair to the seawall and plaza began in December 2009, and was completed in August 2011. This paper discusses the mechanisms believed to be responsible for settlement and lateral movement, summarizes the procedure followed for design of the mitigation, and describes the construction methods and some challenges faced during the repair.

Jan 1, 2011

By J. A. Elliot

Deep Mix-in-Place soil stabilisation is achieved by forming columns of soil/cement arranged to overlap by secant intersection. Alternate columns are constructed initially and infilled. The cementitious material injected is designed to retard the strength of the resulting mix thereby allowing satisfactory overlapping. Columns are constructed using a designed large diameter mixing auger mounted on a smaller diameter auger stem. This is firstly screwed to the design depth removing only such spoil as to enable penetration of the auger, and subsequently counter rotated and extracted in a predetermined mixing pattern and grout injection rate to ensure continuous and homogeneous treatment through each successive level. The process is performed whilst monitoring auger depth, grout flow and pressure. Cementation Piling and Foundations Limited used this technique to stabilise allu­vium and to facilitate the construction, by conventional techniques, of a circular pumping station pit of 10M diameter to 10M below ground level. The work was carried out within 3M of adjacent domestic properties, and on a very restricted site in Elland, West Yorkshire. Ground conditions consist of 2M of cohesive alluvium becoming water bearing and increasingly sandy and gravelly with cobbles which overlies the mudstones at 10.0m depth. Sandstones beneath formed an aquiclude to artesian ground water with the underside of the open excavation approxi­mately 1.0M from the top of this material. Peripheral treatment into the mudstone, coupled with pressure relief wells, proved successful and final excavation depth was achieved in "the dry".

Jan 1, 1989

By Darrell L. Beddard

The Loma Prieta earthquake occurred on October 17, 1989 at 5:04 PM, Pacific Daylight Time. It measured 7.1 in magnitude and was felt from Los Angeles north to the Oregon state line and east to western Nevada. The epicenter of the earthquake was located along the San Andreas Fault, in the Southern Santa Cruz Mountains just north of the City of Watsonville, California. It was the largest earthquake to occur in the San Francisco Bay area since the 1906 earthquake. A total of 87 aftershocks of Magnitude 3.0 or larger were recorded within 21 days after the seismic event. As a result of this earthquake thirteen State-owned and five locally-owned bridges were closed to traffic. Three of the most publicized State-owned structures closed to traffic were Struve Slough Bridge, San Francisco-Oakland Bay Bridge and Cypress Street Viaduct. Struve Slough Bridge was twin slab bridges that collapsed and were rebuilt and open to traffic three months after the earthquake. San Francisco-Oakland Bay Bridge experienced collapse of upper and lower spans at Pier 9 and was reopened to traffic one month after the earthquake. The Cypress Street Viaduct experienced collapse of 48 bents that resulted in the upper roadway falling onto the lower roadway.

Jan 1, 1995

By K. Viking

The vibratory characteristics of full-scale sheet piles, vibratory driven into the ground, have so far not been described systematically in detail. This paper concerns the preliminary results of a series of full-scale field tests where both the driveability and induced ground vibrations have been continuously monitored. Furthermore, the results of measured ground vibration levels have been measured at two different sites characterised as having hard and easy driving conditions. In the light of the presented results, the paper briefly discusses how the complexity of a driveability and vibration prediction can be subdivided into three parts, namely, vibrator-, sheet pile-, and soil-related parameters, all of which significantly affect both the driveability and induced ground vibrations.

Jan 1, 2000

By Garth Howlett

In 1998 the Matanuska-Susitna Borough formed the new port district at Point MacKenzie, known as Port MacKenzie, located directly across the Knik Arm from Anchorage. In 1991 PND Engineers Inc. (PND), working with the Matanuska-Susitna Borough manager and port director, envisioned a fill structure at Port MacKenzie with a 500-foot-long Open Cell? sheet-pile bulkhead face extending to EL -20 feet Mean Lower Low Water (MLLW) at the face. Now under operation the fill created 5.5 acres of tideland property using local materials for fill. The fill is protected from 2- to-3 foot-thick ice pans and 9 feet per second (fps) tidal currents by an envelope of armor rock. Construction required working in water with 30 to 40 feet of tidal variation. Construction required placement of frozen fill in water depths possibly exceeding 50 feet, creating real concerns about soil consolidation and long-term maintenance issues. A plan was prepared to consolidate the soils using Vibracompaction. Soil Density and consolidation were monitored during the work. In 2003 the port district and NPI, a wood chip export company, formalized an agreement to construct a deep water port facility at Port MacKenzie for cape-class bulk carriers. PND provided planning, studies, geotechnical investigation, design documents and construction inspection for a 500-foot-long trestle with a platform dockhead and dolphins providing 1,100 feet of dock face in EL -70 MLLW as shown in Figure 1. Design included installation of large-diameter spin-fin piles driven on a 2V:1H batter. Also included was a 300-ton tension test of smaller spin-fin piles.

Jan 1, 2006

By Adriaan van Seters

"Abstract The content of Eurocode 7 – Part 1 and Part 2 – with respect to piled foundations is outlined. The important role of pile testing is presented and the derivation of the characteristic value of pile bearing resistance is explained. Recommendations for the use of correlation factors are given. The ongoing work of the Evolution Groups on piling is to prepare a revision of Eurocode 7 after 2019. Future topics and changes are highlighted.General outline of pile design by Eurocode 7In his paper for this conference Frank (2014) outlined the various aspects of standardisation for pile foundations, which involves Eurocode 7 as leading for pile construction in Europe. Standards for pile testing and execution of piling works were established in the last 15 years.This paper focuses on the design of piled foundations according to the design code Eurocode 7, which consists of 2 parts:EN 1997-1 Geotechnical design - Part 1: General Rules (CEN, 2004);EN 1997-2 Geotechnical design – Part 2: Ground investigation and testing (CEN, 2007) In Eurocode 7-1, Section 7 – Pile Foundations - deals with the design of piles. The safety concept for pile design is given in Section 2 – Basis of Geotechnical Design - for the three Design Approaches.In Section 7 presents the design of piles according to four methods:1. Results of static load tests2. Empirical or analytical calculation methods3. Results of dynamic load tests4. Observed performance of a comparable pile foundation.Guidelines for the ground investigation for piles is provided in Eurocode 7-2, Annex B.3. In the Annexes of Eurocode 7-2 examples of analytical methods to determine the bearing resistance of a single pile based on the results of various ground investigation techniques are given. Thus calculation models are presented based on design using the results of Cone Penetration Tests (D.6 and D.7) and Pressuremeter Tests (E.3). The Annexes of Eurocode 7-2 are informative.For the interpretation of Eurocode 7, reference is made to Frank et al (2004) and Bond and Harris(2008)."

Jan 1, 2014

By Mohammed Sakr

A Two-Section Helical Pile (TSHP) is a steel pipe with two shaft sections of different diameters and with one or more helix plates near the bottom of each shaft section. TSHPs are used regularly in western Canada as foundation pockets for single and double circuit distribution power line poles. The results of a comprehensive lateral pile load test program and the field monitoring of TSHPs installed in organic soil (muskeg) over soft clay are presented in this paper. A total of nine full scale lateral load tests were carried out, including seven tests using TSHPs with different diameters and embedment depths, and two tests using one-section helical piles. The prime objective of the study was to evaluate the lateral resistance of TSHPs installed into very soft organic soil (muskeg) overlying soft clay soils, to compare their lateral resistance relative to one-section helical piles and to compare the measured and the estimated lateral resistances using p-y curves. In order to provide sufficient soil data for analysis, the subsurface soil stratification was evaluated using two different techniques including; Cone Penetration Tests (CPT) and Portable Soil Probe Tests (PSPT). The two testing techniques were also compared and evaluated. This paper summarizes subsurface soil conditions, pile configuration, helical pile installation procedure, testing setup and results.

Jan 1, 2009

By Harald Ludwig

In 2002, excavation support work commenced on the Capitol Visitor Center project located adjacent to the nation?s Capitol building in Washington, D.C. The outlying work (Slurry Wall Work at Main Site is not discussed) consisted of providing excavation support for a new truck tunnel approximately 1900 feet long up to 50 feet deep as well as support for the new underground auditorium and Library of Congress tunnel. The excavation support consisted of a combination of conventional drilled in soldier beams, lagging, tiebacks and braces; intricate underpinning inside the existing Capitol building; support of an existing Russell Tunnel; soil nailing and tiebacks underneath the existing Russell Tunnel; two temporary bridges; and a deep soil mixed wall with lateral support provided by braces. As part of an on-going research program, some of these braces were instrumented with strain gauges. The deep soil mixed wall was approximately 300 feet long and 65 feet deep on either side of the truck tunnel. Approximately 34,000 sf of deep soil mixed wall, 90,000 sf of conventional excavation support, 200 braces, and 320 tiebacks were installed. This paper describes the large scope and breadth of the project that required a variety of excavation support techniques. A few of the challenges in designing and installing the support of excavation are discussed. This paper also presents the results of the instrumentation program conducted on the deep soil mixed wall, which stood open for more than a year.

Jan 1, 2006

By Helen D. Robinson

Traditional practice to resist large lateral loads on foundations is the use of large diameter caissons, battered driven piles, or battered micropiles. Dense urban construction environments, however, limit the usefulness of these systems due to the close proximity of below- and above-grade obstructions. This paper presents two micropile construction projects in the United States where a complex scheme of battered micropiles and grade beams was developed to counteract large lateral loads at the foundation level. The paper also presents a procedure used to design vertical micropiles for large lateral loads, which can greatly simplify the design of foundations subject to significant lateral loads in urban environments. A design example shows a case where vertical micropiles were used to support allowable design lateral loads greater than 80 kip per micropile.

Jan 1, 2010