Search Documents

"1.0 INTRODUCTIONThese Guidelines reflect the state-of-the-practice of the Deep Mixing Method (DMM) in North America. DMM is an in situ mixing process that breaks down the soil structure; injects binders, fillers and reagents into the soil; and blends them with the soil. DMM is also commonly referred to as Soil Mixing. The final properties of the treated soil in situ are a function of the composition of the native soils and groundwater, the binders introduced, the mixing methods and energy, and the conditions and time of curing. Treated soils generally have increased strength and stiffness and/or reduced permeability relative to the native soils.This document addresses DMM performed by rotating single and multiple axis mixing tools, rotating cutter wheels at the end of a rigid kelly bar, or trench mixing using a rotating cutting/mixing chain around the perimeter of a rigid bar. Binder may be injected through low or high energy (velocity) jets.The treated soils created through wet DMM are heterogeneous mixtures of binder, water, soil, and groundwater. Treated soils produced by dry DMM techniques are a mixture of binder, soil, and the water already present in the native soil.DMM applications described in this document include•,Earth retention•,Liquefaction mitigation•,Groundwater seepage control and containment isolation•,Bearing capacity improvement•,Deep foundations•,Mass stabilization and contamination containment•,Embankment, levee and dam strengthening, and stabilization•,Casing replacementThis document was developed to address deep foundations applications. Use of deep mixing for seepage control is not specifically addressed. The reader is referred to documents prepared by the U.S. Army Corps of Engineers for additional information. Shallow soil mixing and the use of DMM for stabilization/solidification of contaminated soils performed at depths less than 10 feet (3 m) are mentioned briefly. Jet grouting is not covered by these guidelines."

Jan 1, 2016

By David A. Hart, Barry P. Osborn, Richard J. Totty, Ana T. Carvalho, Max B. Elliott

This paper addresses the experience designing and installing bored piles for the King’s Cross area. This includes continuous flight auger and rotary bored piles, with a range of diameters between 600 mm and 1200 mm, reaching a maximum depth of 56 m below ground level. Existing Network Rail Thameslink twin bored running tunnels are located directly beneath the subject plots. These tunnels have an external diameter of 6.6 m and the crowns of the tunnels are very shallow, in some cases just 10 m below the existing ground level. Some plots needed piles to be installed in close proximity to the tunnels, which required additional control measures and contingency plans. Pile verticality was monitored as the tip of each pile advanced and in-tunnel monitoring readings were verified and are presented. Lessons learned from designing, installing and testing the piles and monitoring the tunnels are addressed in this paper.

May 1, 2022

By Frédéric Rocher-Lacoste

On July 2nd, 2007, LCPC and LOADTEST performed a static loading test with an Osterberg-cell on a bored pile of 1600 mm diameter. The 56.50 meters deep test pile constructed by Trevi Spa for Soares da Costa group, was near the Cacheu river in Guinea Bissau. This test was conducted to validate the design of the foundations of the Sao Vicente bridge; a project undertaken by the Ministry of Public Works of the Republic of Guinea Bissau and funded by the European Development Fund. Sub-surface conditions at the test pile location consist primarily of layers of weak sands and clays. The piles were loaded statically using the O-cell® bi-directional method 25 days after concreting. The maximum sustained bi-directional load applied to the pile was 11.7 MN. At the maximum load, the displacements above and below the O-cell assembly were 6.6 mm and 81.9 mm, respectively. The resulting pile head behavior has been calculated for a combined skin friction and end-bearing load of 29.3 MN. The piles were also instrumented using LCPC removable extensometers, which made it possible to measure the mobilization of shaft friction and toe resistance. The adjusted test data indicated that this pile would settle approximately 12.2 mm for the service load of 12MN applied at the head of the pile. This paper provides a very brief presentation of the bridge project and the test pile instrumentation: LCPC removable extensometers and O-cell® instrumentation. The results are detailed and analyzed herein and the combined use of these two instrumentation systems is a world première.

Jan 1, 2008

By Timothy Nelson, Simon Burnworth

"The Berkeley Art Museum and Pacific Film Archive (BAMPFA), which currently resides in a 1970s-era post-modern concrete structure just south of the University of California, Berkeley campus, was in need of a new home after an engineering evaluation revealed that the building possessed seismic deficiencies. Pressed for space, the University looked within its portfolio of properties and identified the site of the former University Printing Press facility as the place to build BAMPFA’s new home.The site was perfect; located one block east of bustling downtown Berkeley and its rapid transit station, and directly across the street from the western entrance to the UC Berkeley campus. Thousands of pedestrians pass by the site on a daily basis, thus granting BAMPFA the opportunity to reshape the corner of Center and Oxford Streets with a building that would not only welcome visitors to campus, but also serve as a creative hub for both the City of Berkeley and the UC Berkeley institution itself 1.The original museum plans, drawn up in the mid-2000s, called for complete demolition of the existing abandoned facility and replacement with a visually stunning structure designed by renowned Japanese architect Toyo Ito. Even at this point, the shoring and means and methods requirements of the project were identified as a challenging component, incorporating a shored excavation bounded on three sides by busy city streets and a fourth side by an operating bank and occupied apartment building. Furthermore, a sequenced demolition would be required for the printing press facility’s three-story Administration Building (also known as the Admin Block), one-story printing press warehouse (also known as the Press Building), and an adjacent parking structure. Degenkolb Engineers was retained at that time as the shoring engineer to design the shoring to facilitate this work."

Jan 1, 2016

By Kiyotaka Ohno, Nobushige Yasuoka, Yosuke Hioki

"The diameter of improved columns adopted by the original DJM Method had been 1000 mm, however, in order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter expanded to 1300 mm was developed between 1998 and 2001 and has been widely applied since then. From the first application of EX-DJM in January 2002 for a first construction project, the total volume of improved soil has reached 325,000 m3 in 17 projects up to September 2014. Because of the advantages of the EX-DJM such as reduction of construction costs and periods leading to reduction in the number of improved columns, adoption of this method is expected to increase in the future. This paper describes the advantages of the EX-DJM, its construction results and case examples including those applied to restoration projects after the Great East Japan Earthquake, 2011.1. BACKGROUND OF DEVELOPMENTThe Dry Jet Mixing (DJM) Method is a soil stabilization method in which a powdery or granular binder is pneumatically fed into and mixed with soft soil to induce chemical reactions that stabilize and strengthen the soil. It was developed by government - private collaboration in Japan between 1977 and 1979. Up to March 2014, the total volume of soil improved by DJM method reached 33,500,000 m3. The initial diameter of improved columns of the original DJM Method was 1000 mm. In order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter 1300 mm was developed between 1998 and 2001.2. ADVANTAGES OF EX-DJMThe construction equipment for the EX-DJM consists of two major parts, which are DJM machine and binder plant are shown in Fig. 1.The construction machine is of double mixing-shaft type with its column diameter expanded to 1200mm or 1300mm. In association with the increase in the column diameter, the binder feeder has also increased its discharge rate by approximately 1.69 times. Same as the increase rate of the area of original diameter 1000mm to diameter 1300mm are shown in Fig. 4."

Jan 1, 2015

By Graeme Smart, Thomas Fiala

"Yorkville Plaza II, a 40-storey signature condominium residence, is scheduled to open on Avenue Road in Toronto’s prestigious Bloor-Yorkville neighbourhood in spring 2017. In close proximity to Toronto’s subway system, the new tower requires six levels of underground parking, founded in wet, silty sand.Isherwood Geostructural Engineers (Isherwood) was retained in April 2012 by developer Camrost-Felcorp to provide a shoring and excavation solution to address the challenging site conditions. A 31-storey upscale residential building under renovation with three levels of parking, owned by Camrost-Felcorp, flanks the site on the north. Situated on the eastern border is a 7-storey building with three levels of parking. Avenue Road, a four-lane arterial road that brings heavy commuter traffic into downtown Toronto, runs along the western border, and on the southern border of the site is a busy City road that brings traffic into the popular Yorkville area. The tunnel for the Toronto Transit Commission’s (TTC) overburdened east-west subway is located 14.5 m to the south, running below an existing 26-storey neighbouring building. Electrical and communication utilities (Bell) are closely located along the southern side. Non-documented existing excavation shoring, installed in the early 1970s, on the southern and western sides compounded the difficulties presented by the TTC tunnel.This paper presents the unique, non-conventional hybrid shoring solutions Isherwood developed to address the challenges presented by the site, as well as other complications that surfaced during the project: non-encroachment requirements (no tiebacks) beneath uncooperative neighbours, tight geometry to install shoring, and Toronto’s two coldest winters in decades.THE PROJECTBecause of circumstances associated with this site, for this project Isherwood designed two unique shoring walls which drew on their experience and expertise they had gained over the last 40 years. The following is the story of this site:Yorkville is an affluent neighbourhood in the heart of Toronto with a vibrant mix of high-rise towers, residential homes, tony restaurants and flagship shops. The development requires six levels of underground parking (a 20m deep excavation), with three levels undermining the high-rise buildings to the north and east and extending into wet, silty sand.Isherwood was retained in the spring of 2012 to design the excavation shoring. Isherwood’s scope also included field support, design, verification and monitoring. Finite Element Analysis was employed to confirm Isherwood’s design and anticipated movement of the south shoring wall and the TTC subway tunnel.The existing site was severed in two, with the proposed condominium tower slated for the southern portion. On the north half of the site stands a 31-storey building (Yorkville Plaza I at 21 Avenue Road), with three levels of underground parking, sitting on belled caissons which were one foot from the back of the proposed shoring wall so this would have to be considered in relation to the design and drilling methods. Constructed in the early 1970s, Yorkville Plaza I is currently being converted from the Four Seasons hotel to luxury condominiums by Camrost-Felcorp. To the east, directly adjacent to the proposed shoring, stands a 7-storey building (164 Cumberland Road) with three levels of parking, supported on spread footings founded on stiff clayey silt. The tunnel for the TTC’s busy east-west subway, a double box structure built by cut-and-cover in the 1960s, is located 14.5 m to the south, 9 m below grade, and running below an existing 26-storey building. Bell fibre optic communication cables and electrical lines, along with storm and sanitary sewers, are situated on the south and west sides of the site, leaving limited room to install shoring. Due to the heavy volume of commuter traffic on the four-lane arterial road (Avenue Road) to the west, site access and lane closure were not permitted here."

Jan 1, 2015

By Kyle Kershaw

Micropiles are routinely used in the United States for foundation support and stabilization of slopes. In recent years, several retaining walls have been constructed using micropiles in an A-frame type configuration to support temporary and permanent excavations at sites with limited access and limited right-of-way. Typical A-frame micropile walls consist of a row of vertical micropiles at the face of the wall and a row of battered micropiles extending into the soil or rock to be retained. The two rows are then tied together with a pile cap such that the front pile acts primarily in bending and the back pile acts primarily in tension. Because of tight right-of-way constraints at a residential site in Aspen, Colorado, it was not possible to construct the wall using conventional shoring systems or micropiles in the typical A-frame configuration. Rather, the wall was designed such that the row of battered piles was installed at the wall face and the row of vertical piles was installed adjacent to the property line behind the wall. As a result of the reverse configuration of the A-frame wall, FLAC, a two-dimensional, finite difference software program, was used to model the soil-structure interaction. The final wall design consisted of both temporary and permanent retaining wall sections with maximum heights of 26 feet. Inclinometers were installed in several piles to monitor the behavior of the retaining walls during and after excavation. This paper presents an overview of the design method, a discussion of construction techniques, and a comparison between the FLAC model and the measured behavior of the wall in the field.

Jan 1, 2007

By Uwe Hess

For the Danish landworks for the coming fixed link between Denmark and Sweden across the Øresund the focus has been on the environmental aspects of the construction and operation of the facilities. This paper describes how the environmental objectives pertaining to the project have influenced the design and construction of one of the major elements of the Danish landworks, i.e. the tunnel in Sydhavnsgade and under Sydhavn Station. The chosen construction methods for the construction pit bracing and the groundwater lowering will be described along with the observed effects on the environment as shown by simulated or measured values for noise impact, settlements, pumped groundwater and extension of the drawdown cone.

Jan 1, 1996

By Renato P. Cunha

The paper explores a parametric analysis of a four-pile group in contact (hence piled raft) and without contact (hence standard pile group) with the superficial soil layer, under a combined set of loadings (moment M, vertical V and horizontal H forces). The major design parameters of interest, as total and differential settlements, and raft bending moments and shear stresses are assessed under aforementioned distinct conditions. The slenderness ratio of the piles is also varied along the analyses, allowing the establishment of its influence on the derived parameters.

Jan 1, 2006

By John C. Niedzielski, A. Frances Ackerman

The existing US-70 Bridge over the Gila River at Bylas, Arizona is planned to be replaced due to its current poor condition. The replacement bridge is planned to be a 15-span, 1,904-foot (580 meter) long bridge, the third-longest bridge in the state highway system. Within the Gila River floodplain, granular alluvial soil is underlain by cohesive lacustrine soil; bedrock was expected due to nearby terrain but not encountered within the geotechnical exploration depth of 166.5 feet (51 meters) or less. Based on the anticipated loading conditions, design scour depths and the soil conditions, the full structural loads are carried by large diameter drilled shafts; therefore accurately determining the axial capacity of the proposed drilled shafts has important practical and safety implications. The conventional methods for axial capacity determination may be overly conservative to use for design in the site’s layered granular and hard clay soils. An Osterberg cell load test was performed to obtain detailed information on the load transfer from the drilled shaft in side friction and base resistance to allow optimization of the bridge foundation design. The fullscale field test played a significant role in the design of the project’s deep foundations, notably, by incorporating the specific subsoil properties and consequently, an exact prediction of the load-settlement behavior under loading. This paper provides the results of the geotechnical site investigations, drilled shaft load testing procedures, and shaft load distribution from the load test results. Comparisons were developed between predicted axial capacities of drilled shafts using several design methodologies and the axial capacity measured from static load testing. The load test results showed that underestimation of the axial capacity is evident using conventional methodologies. The exact prediction of the load-settlement behavior under loading combined with a site-specific design approach, resulted in a substantial reduction of foundation costs due to reduced drilled shaft dimensions.

Jan 1, 2017

By Dewey W. Geary, Rachael V. Bisnett, R. Michael Bivens, Thomas G. Andrews

"The powerhouse for the Red Rock Hydroelectric Project is being constructed at the toe of the existing U.S. Army Corps of Engineers’ Red Rock Dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends though overburden and 40 feet into rock. Prior to rock excavation, a grouting was performed around the excavation for the purpose of increasing the strength of zones of fractured rock. For the majority of the perimeter, the rock was fairly tight and grout takes were relatively low. However, for a 160 foot extent along the landside of the excavation, extensive grouting was required to treat a two to five foot thick zone characterized by artesian flows from grout holes on the order of 20 gallons per minute (gpm) or higher from a voided zone in rock that was partially filled with sand, clay, and rock fragments. This paper discusses the treatment measures used to fill and improve the strength of this zone, which ultimately entailed a combination of thick cement grout and polyurethane grout, holes spaced as close as 18 inches on-center, and two additional rows of grout holes.IntroductionThe Red Rock Hydroelectric Project (Project) is currently under construction at the existing U.S. Army Corps of Engineers’ (USACE) Red Rock Dam on the Des Moines River near Pella, Iowa. At peak generation, the Project will generate up to 55 MW with an average annual energy output of 178 gigawatt-hours.The powerhouse for the Project will be located at the toe of the existing dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends up to a depth of 40 feet into rock through the St. Louis Limestone and terminates in the Warsaw Limestone. Prior to rock excavation, grouting was performed around the excavation for the purpose of improving the strength of zones of fractured rock. An auxiliary benefit of the grouting was reducing seepage into the excavation. Grouting began on July 20, 2015 and ultimately concluded on September 26, 2015.Drilling and grouting occurred as planned on the riverside (southwest) of the excavation along the cellular cofferdam and stilling basin wall (grout holes P-1 through S-13) and on the upstream (northwest) side of the excavation along the secant pile excavation support wall (grout holes P-14 through S-19) (refer to Fig. 1). The rock in these areas was generally tight with relatively low grout takes. However, on the landside (northeast) of the excavation (grout holes P-20 through P-28), partially infilled voids and artesian flows were encountered during drilling generally between depths of about 28 to 40 feet."

Jan 1, 2016

By Scott Webster

Dynamic pile Monitoring Services (DMS) have been used for testing of offshore piles for several decades. However, most of this testing was to measure hammer performance and pile stresses rather than pile capacity or soil resistance. As the need for more economical solutions for foundation support increases, the use of DMS has provided a better means of evaluating in-place pile capacity for offshore structures, and therefore a method of determining pile acceptance. The authors have been involved in several offshore projects where DMS has been the primary source of data for acceptance of the driven pile foundations. The use of DMS for evaluation of offshore foundations requires considerations quite different from land applications and these considerations are often necessary for the careful and thorough analysis of the collected data in nearly real time for determination of pile acceptance. Case Method capacity estimates are often of little use due to the non-uniform cross sections of the foundation piles and their deep penetrations. Therefore, capacity assessments should be made using CAPWAP which is a signal matching program whose utility and reliability has been proven on thousands of projects every year, both on land and offshore. Depending upon the soil conditions at a given location, capacity assessment after soil setup effects may be necessary. In addition, tension capacity is often critical when pile refusal occurs significantly before the design pile penetration depth. Evaluation of uplift capacity can be accomplished by a CAPWAP analysis, which results in a total capacity prediction and its shaft resistance component. The use of hydraulic hammers for driving of these piles also adds the requirement of controlling hammer energy such that over-stressing of the pile is avoided. The calculation of non-axial stresses such as bending or eccentric stresses may also be involved in order to prevent pile damage.

Jan 1, 2010

By Peter Cali, David Yang, Rakshya Shrestha, Ralph Griffin, Sushil Kafle, Motoji Watanabe

"As a part of the ‘US Army Corps of Engineers - New Orleans to Venice, Louisiana Hurricane Protection Project’, deep mixing ground improvement was designed to reinforce the soft ground for the emergency repair of a 7297-foot (2,224 m) long section of the Mississippi River West Bank levee in Buras Levee District under the contract ‘Emergency Levee Repairs – Contract P-17A, Plaquemines Parish, Louisiana’. The ground improvement utilizes a series of soil-cement panels oriented in the transverse direction of the levee. Each soil-cement panel consists of overlapped columns installed by the deep mixing method (DMM). DMM is performed from the existing top of levee and extended to competent stratum at depths varying from 26 feet (7.9 m) to 47 feet (14.3 m) below the working platform. The main purpose of the DMM panels is to provide shear resistance to the levee against lateral loads at high flood water condition. The DMM panels support the additional vertical load created by the increased height of the levee for hurricane protection and control the long-term settlement of the remediated levee, which might otherwise occur due to the compression of soft foundation soils. The total amount of DMM treatment is approximately 54,000 cubic yards (41,500 cubic meters). This paper reviews the project background, subsurface soil conditions and presents the design, construction and quality control of the deep mixing work for this levee repair project.INTRODUCTIONIn August 2005, Hurricane Katrina caused major damage to the federal and non-federal flood control projects in southeast Louisiana. In September 2005, Hurricane Rita caused further damage to this flood protection system. In an effort to minimize further damage and to enhance the protection level, certain non-federal levees located on the west bank of the Mississippi river in Plaquemines Parish, Louisiana were incorporated into the New Orleans to Venice Hurricane Protection project by the US Army Corps of Engineers (USACE). DMM techniques were then utilized by the USACE in several of these emergency projects and in many medium sized projects between 2006 and 2010 (Bruce et al. 2012). This project (called P-17A hereafter) which forms a part of this protection system is executed under the contract Emergency Levee Repairs, Contract P-17A. This is one of the largest projects of the USACE after LPV- 111. The huge LPV-111 project (5.5 miles (8.9 km) of levee) treated by DMM), the largest DMM project ever conducted outside Japan, began in 2010 and was completed in 2012 (Cali et al. 2012, Bruce et al. 2012).DMM is utilized at P-17A to construct a series of soil-cement panels oriented in the transverse direction of the existing levee to provide shear resistance to the levee against the lateral load during high flood water condition. The project extends 7297-foot (2,224 m) along the West Bank Levee of the Mississippi River in the Buras district of Louisiana, parallel to Louisiana Highway 23 (LA-23) as shown in Figure 1. It is located approximately 60 miles (96 km) south-east of downtown New Orleans."

Jan 1, 2015

By Brian Metcalfe, Kord Wissmann, Gianni Martinez

The Middle East consists of vast deserts that reach temperatures up to 50 degrees Celsius, with some areas characterized by endless sand dunes. When the project team selected the location for a large new transportation project, little did they know that the site would be characterized by soft, nearly normally consolidated silt and clay extending below a thin sand crust. Searching for solutions, the design team elected to reinforce the subsurface with Rammed Aggregate Pier® (RAP) ground improvement elements and desired verification that the novel method would stand the test of prolonged static loads. Because the concrete pavements would serve to spread the load, a “zone load test” was performed, consisting of applying a uniform bearing pressure of 150 kPa over a 7.5m square concrete footing. Unlike individual pier load tests, the zone test allowed the project engineers the opportunity to confirm design parameter values under large-loading area conditions, a situation not often available to most designers. This paper presents the results of the zone load test whose results may be interpreted to better understand design parameter values. This paper is of particular significance because it adds a value contribution to the relatively few numbers of “group load tests” available in the literature for ground improvement applications.

May 1, 2022

By Diane Reid, Antonio Marinucci, Robin Mao

Super Cells are an innovative, open-shaped bi-directional static load testing device used to promote concrete flow during placement while utilizing greater cross-sectional area of the pile to achieve large applied axial loads at relatively low hydraulic pressures (≤ 250 bar). This paper describes the results of multi-level load testing performed on a sacrificial drilled shaft that was 3.8 m (12.7 ft) in diameter and 110.6 m (363 ft) in length for the Jiaxing-Shaoxing River Crossing Bridge that spans Hangzhou Bay in Shaoxing, China. The test shaft was instrumented with embedded strain gauges and telltale rods along with displacement transducers at the top of the pile to measure the load-induced displacements along the length of the shaft. Load testing was performed twice using a Super Cell placed near the tip of the shaft, prior and subsequent to tip post-grouting, and then again using a Super Cell placed higher in the shaft. The axial resistance for the tested conventional drilled shaft was more than 5 times greater than the estimated axial resistance. In addition, the axial resistance after tip post-grouting (347,100 kN (39,033 ton)) was about 5.3% greater than the ungrouted axial resistance (329,600 kN (37,050 ton)). INTRODUCTION During the past few decades, the magnitude of axial, lateral, and flexural loading has considerably increased due to updated design codes, larger superstructures, and the manner in which extreme event loading (e.g. seismic and scour) is incorporated into design. The diameter and depths to which bored piles or drilled shafts are constructed have increased considerably during the last three decades due to the advancements in equipment technology and capabilities. In addition, monoshaft foundations have become increasingly used, as one large drilled shaft is able to replace a group of smaller diameter piles connected by a cap. Correspondingly, adequate strata, for both side and end resistance, must be discovered/determined as well as achievable to be able to construct the required foundations to support the greater design demands. As design demands have increased, the need to ensure integrity, quality, and performance of a constructed drilled shaft has become ever more crucial. Load tests are essential to validate design assumptions of side and end resistances, to assess the behavior and load transfer characteristics of the constructed drilled shafts, and to evaluate construction methods. Load tests utilizing a bi-directional static load testing (BDSLT) device can achieve considerably large applied axial loads and can be performed more economically, in less time, and in a much safer manner than conventional top-down static load testing methods.

Jan 1, 2019

By Rob van Dorp

"AbstractThe Monitoring & Instrumentation Committee (MIC) of DFI Europe has the objective to support DFI members in concern of risk management of geotechnical matters, where monitoring and instrumentation have added value.Work of the CommitteeA study by the committee showed that there are already several existing (national) guidelines. They all have their strengths and limitations and their focus may vary a little per country due to local regulations and typical local building activities, but the main question remains what added value another new guideline would have. More likely it would add to the confusion instead of providing overview.Companies with larger experience in geotechnical monitoring (often larger consultancy firm, contractors or clients) are already quite familiar with its benefits do not really need a new guideline in how to design and effectively apply sophisticated geotechnical monitoring systems for special projects.Therefore the aim of the MIC is to focus a little more towards smaller organizations - that are less familiar with monitoring and instrumentation - and the more ‘regular’ type of project that they are mainly involved in. The MIC wants to create a tool which helps them to create risk awareness, to understand the benefits of geotechnical monitoring and to provide them information about how and where to find the right partners and equipment to setup and apply appropriate monitoring systems for their projects.Monitoring and instrumentation benefits are for example:• Risk control during construction stage;• Costs reduction in design and construction (taken limitation of geotechnical aspects into account).• Prevent of unnecessary delays in construction work• Increasing general awareness of geotechnical risks and possibilities of monitoring.The cost of monitoring compared to the cost of failure and/or the savings that can be achieved play a role in the work of the committee. DFI members benefit from the shared knowledge by the MIC on monitoring and instrumentation within their process of risk management."

Jan 1, 2014

Jan 1, 1991

Jan 1, 1997

By Atta B. Yiadom, A. David Miller, Robert C. Kirby, Sean M. Todaro

"San Pablo Dam is a 170-foot (52-meter)-high earthfill embankment, located approximately 10 miles (16 kilometers) north of downtown Oakland, California, that impounds a 38,600 acre-feet (47.6 million m3) reservoir for customers in the East Bay Municipal Utility District's (EBMUD's) service area. Seismic upgrades were designed and constructed in 2008 through 2010. Work included removal of an existing 140,000 cubic-yard (107,000 m3) downstream buttress, which was replaced with an enlarged 300,000 cubic-yard (230,000 m3) buttress founded on alluvium and colluvium that were improved in-place using Cement Deep Soil Mixing (CDSM) technology. The site characterization for the project, design of CDSM, reuse of CDSM spoils as construction materials, and environmental permitting have been described in five previously published professional papers.This paper provides a brief summary of the design of the seismic upgrades and presents the results of measurements made during and/or after construction including the variation of CDSM strengths with time, piezometric levels within the dam and foundation soils, and seepage flow rates. These measured values are compared to the values estimated during design of the seismic upgrades.INTRODUCTIONSan Pablo Reservoir is located approximately 10 miles (16 kilometers) north of downtown Oakland, California, as shown in Fig 1. As many as 50 million gallons (200,000 m3) per day pass through the reservoir for treatment and distribution to a portion of the 1.3 million customers served by EBMUD. The dam is founded mainly on alluvium and was originally built in 1920 using materials excavated from the left and right abutments consisting of siltstone, claystone, fine-grained sandstone, mudstone, and shale that were excavated and placed using hydraulic fill methods. The dam is located within two miles (three kilometers) of the Hayward Fault which is capable of a moment magnitude 7.25 earthquake.Because of the foundation materials, construction method, and proximity to the Hayward Fault, the dam has undergone a series of seismic improvements, including the placement of a downstream compacted earth buttress in 1967 and an upstream compacted earth buttress in 1979. In 2002, the State of California Division of Safety of Dams (DSOD) requested that EBMUD evaluate the seismic stability of San Pablo Dam, following the results of a study that same year that indicated a 62 percent chance of a greater than 6.7 magnitude earthquake striking the San Francisco Bay region between 2003 and 2032. The dam was evaluated and it was concluded that portions of the underlying foundation soils may liquefy during the maximum credible earthquake which could cause the dam to become unstable."

Jan 1, 2015

Jan 1, 2002