Search Documents

By Ronnie Melker, Joel Webster, Daniel Belardo, Thomas Hyatt

Quality assurance of drilled shafts is highly dependent upon the construction practices used during the excavation and concrete placement process. When performed under slurry, challenges are presented in maintaining borehole stability and placing a uniform and continuous concrete column. An integral part of the construction operation is to evaluate the as-built integrity to verify the drilled shaft is capable of safely transferring the required loads to the subsurface. One such case is exemplified by a project involving the expansion of an existing public transit rail line. The expansion required the construction of a new bridge bent supported by seven 5-ft diameter drilled shafts of various lengths. The specifications for the project required both Cross-Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP) for drilled shaft integrity evaluation. Both of these post-construction non-destructive tests (NDT) are designed to detect anomalies or the presence of regions with reduced concrete quality. However, the implementation and methodologies of performing each of these NDT methods are significantly different. Cross-Hole Sonic Logging uses ultrasonic signals emitted from a transmitter in one access tube to a receiver in another access tube. Thermal Integrity Profiling measures elevated concrete temperatures during the curing process using embedded thermal wires. Both test methods require different access details and therefore have different costs associated to the contractor or owner to perform. This paper provides a detailed comparison of these NDT methods as performed on these seven drilled shafts. The associated financial and time costs to perform each method are compared and the results are discussed in detail. INTRODUCTION Drilled shafts are a fundamental deep foundation element that can be designed to resist large bending moments as well as to transfer large compressive axial loads through weaker upper soils to competent soils or rock below. Often times when the upper soils are very soft, lateral support by casing or slurry, or a combination of both, may be used to hold back the softer soils from collapsing into the hole before concrete has been placed. Due to the blind nature of drilled shaft construction and the qualities issues that may arise during the placement process, it is essential for design engineers to specify non-destructive testing (NDT) to assess the quality of the as-built drilled shaft. CSL and TIP testing are two NDT methods designed to detect areas of lower quality concrete or soil inclusions throughout the length of the drilled shaft and determine its overall quality. Each method uses different technologies and methods to achieve the results required to determine the as-built condition of the drilled shaft.

Jan 1, 2019

By Adrian Gygax, Sarah Gaib, Rod Kostaschuk

The British Columbia Ministry of Transportation and Infrastructure (Ministry) recently completed a slope stabilization project at Ten Mile Slide on Highway 99. The highway is an essential part of the road network connecting the British Columbia (BC) coast with the interior of the province. The landslide was first identified in the mid-1980s and has retrogressed more than 250 m upslope since then, leading to continual and expensive repairs to the highway. The Ministry engaged BGC Engineering Ltd. (BGC) and their structural sub-consultant Gygax Engineering Associates Ltd. (GEA) to develop a stabilization scheme that would halt the slide with an acceptable level of residual risk. The design required careful consideration of construction stages and the stresses induced in the structural components as the slide movement was progressively stopped as construction advanced. Four stabilization design options were shortlisted with the preferred option selected in Fall 2016. The selected solution comprised the construction of five rows of post-tensioned soil anchors upslope of the highway and a tied-back concrete tangent pile retaining wall for the roadway itself as well as reconstruction of the highway alignment, grade and drainage through the slide. Works were installed by top-down construction within defined time allowances stipulated in the contract. Significant engineering was undertaken beyond standard design processes for this complex project, such as comprehensive geotechnical investigations, aerial and terrestrial laser scanning and change detection analyses, pre-production test anchors, detailed geo-structural numerical modelling and due diligence activities to validate and optimize the design. The stabilization works have been very successful with the slide response being as predicted and the highway operating again as full two-lane service.

Oct 1, 2022

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid shoring system consisting of cast-in-place soldier piles with Cutter Soil Mixing (CSM) infill panels was constructed for temporary support of a 19.8 m (65 ft) deep excavation in Vancouver, British Columbia, Canada. Deep Mixing (DM) was completed up to 9.7 m (32 ft) in fill, peat, wood waste and clayey silt with embedment in dense till, and soldier piles constructed through the dense till extending to below final excavation level. Two trial CSM panels were installed ahead of production to assist with developing the termination criteria of the CSM panels in the dense till. The constructed depth of the CSM panels was based on interpretation of real-time monitoring data obtained through the Bauer B-tronic system. Inclinometer monitoring data from two CSM panels and two soldier piles, as well as soldier pile survey target data was used to assess and monitor the performance of the hybrid shoring system throughout bulk excavation. The objectives of this paper are to provide an overview of the design and construction aspects of the hybrid DM shoring system and to present inclinometer and pile target data to demonstrate the lateral performance of the CSM infill panels and soldier piles. This paper also discusses the merits of using real-time monitoring data as part of the engineering decision-making process for validating CSM panel construction. BACKGROUND A hybrid DM shoring design was recently completed for a high-rise development in downtown Vancouver, British Columbia for temporary support of a five level basement excavation. Deep mixing was proposed by the excavation and shoring design-build team as the preferred method to construct infill panels between soldier piles because of the speed at which the shoring system could be constructed in variable fill, peat, wood waste and overburden compared with traditional secant piling methods. The development site is generally a truncated triangle in plan, with the longest side of the triangle being approximately 115.7 m (380 ft) long and the two shorter sides being approximately 71.6 m (235 ft) (Hybrid Shoring Wall 1) to 75.0 m (246 ft) (Hybrid Shoring Wall 2) long. The site is bounded by an existing bridge off-ramp structure along its longest side, and by city streets on the other two sides, as shown in Figure 1. The truncated section is approximately 16.8 m (55 ft) (Hybrid Shoring Wall 3) long. Due to project constraints, the hybrid DM and soldier pile shoring system was only proposed for the two shorter sides of the triangle and the truncated section. Traditional secant piles were installed for the longest side. This paper focusses on the hybrid shoring system. A typical detail showing the CSM infill panel with the soldier piles is presented in Figure 2."

Jan 1, 2017

By William H. Walton, Clyde N. Baker Jr., Darren S. Diehm

"A 51-story concrete core and steel frame commercial office tower was recently constructed on the site of the former US Gypsum building in downtown Chicago, Illinois, USA The structure foundation reused several caissons from the demolished US Gypsum building supplemented with new belled caissons bearing on silty clay hardpan. Extensive in-situ pressuremeter testing was performed during the geotechnical investigation to determine allowable bearing capacity and better estimate building settlements. Problems during foundation construction along the south side of the building frame required remediation of two caissons. One caisson was supplemented with micropiles, while the second caisson was abandoned and replaced with a straight-shaft rock socketed caisson. To determine the effectiveness of the repairs, the building foundation settlements were monitored during construction.IntroductionIn 2001, The John Buck Company began development of a new office tower at the southeast corner of West Monroe Street and South Wacker Drive in Chicago, Illinois. The site was formerly occupied by the 18-story US Gypsum (USG) building. Mr. Clyde N. Baker, Jr. (Senior Principal at STS Consultants, Ltd .) served as the foundation engineer for USG which was completed in 1962. The building was founded on a forest of belled caissons bearing at elevation -56 Chicago City Datum (CCD). For reference, the ground surface at Upper Wacker Drive is approximately elevation +20 CCD. The bearing material was a hard silty clay, locally described as Chicago Hardpan. The foundation caissons were designed using an allowable bearing pressure of 16 ksf (766 kPa). In 1996, the USG superstructure was razed, and the three-level basement was converted to an underground parking ramp.South Wacker DevelopmentThe 51-story high-rise building was completed in 2005 with a structural height of 681 feet (208 m), and an internal space of more than 1,000,000 square feet (93 ,000 square meter). The typical floor size is 27, 700 square feet (2, 570 square meter). Renderings of the building are provided in Figures 1 and 2. The largest single tenant is the accounting firm of Deloitte & Touche, which occupies roughly 45% of the building space with over 3,000 employees."

Jan 1, 2005

By Ronnie X. Gu, Xing Zheng, Gem-Yeu Ma

Due to implementation of the rotator construction method from which a smooth shaft was anticipated, a full-scale pile load test (Osterberg Method) was performed at Pier 14 Pile 9 of the main span of the New Benicia-Martinez Bridge to confirm the design parameters of the rock sockets. Two levels of load cells were fabricated in the reinforced cage of the rock socket. Each level consisted of three 670-mm Osterberg load cells with a total testing capacity of more than 50 MN in both directions. In an attempt to separate side friction and end beari ng, a 75 mm thick compressible Styrofoam material was placed at the bottom of the cage. The pile load test was carried out in four stages. The multi-level multi stage pile load test data was interpreted for casing friction, side friction for two rock strata, end bearing, and residual side shear values under repeated loading in opposite directions. The side friction from the casing in soils at Stage 2 is approximately 9 MN. The end bearing at the tip of the rock socket at Stage 3 was calculated to be approximately 17 MN at a displacement of about 75 mm. The residual side shear resistance for the 10 m 50% RQD rock strata was calculated to be 9 MN or approximately 50% of initial values, after being pushed 0.3 mm upward in Stage 1, 71 mm downward in Stage 2, then 55.5 mm upward again in Stage 3, and finally 105.3 mm downward in Stage 4. The test results surprising ly indicate that the side shear resistances from both low RQD intensely weathered rock and higher RQD slightly weathered competent rock are about the same at approximately 19 MN. This pile load test provides very critical information for confirming deep shaft design and analyses.

Jan 1, 2005

By Nagarajkumar BV

Pavai-and TeampT JV started working on the project T49A, Sumbar J & K State as part of slope and earth stabilization for ongoing Banihal - Katra Railway Connection Project. This project has several tunnels and bridges with slopes that are protected with various types of protection system such rock bolting, rock anchors, and micro piles. For the main two bridges Bring number 2 and 3 at T49 A location Pavai - TeampT JV has to design and execute the circular group of micro piles (Fig.1) for deep excavation of earth for the purpose of construction of well foundations (CAISSON FOUNDATIONS) for both bridge 2 and 3 piers. In this paper we discuss about the purpose, basic design, detailed design approaches and actual work implementation of micro pile with composite rock bolt applications and permanent rock anchors for slope stabilization works in this project.

Nov 1, 2022

By Suresh Chikati, Gangadharan Santhanam

Twin tunnels were constructed to a length of 863m using TBM in one of the underground metro projects. The tunnels pass through complex geological conditions (soil, rock and mixed conditions). This paper presents the consideration of volume loss and the corresponding ground settlement associated with the excavation of twin TBM tunnels by analytical and numerical methods. Empirical methods were used to calculate the ground settlement induced by the excavation of twin tunnels. The ground settlement values were directly derived from the two parameters: the volume loss and trough width parameter. These parameters are calculated based on the geological conditions at the tunnel face and tunnel overburden. The finite element software, Plaxis 2D was used to model the soil parameters with appropriate geological conditions. Twin tunnel excavation is simulated in Plaxis 2D and the effect of tunnelling on the ground was simulated by percentage volume loss. The suitable line contraction value was applied to the tunnel linings to simulate the volume loss. The surface ground settlement was directly obtained from Plaxis 2D. Instrumentation arrays were proposed along the twin tunnel alignment, to provide the ground settlement monitoring data within the influence zone of tunnelling activities. The derived ground settlement values from analytical and numerical methods were compared with the actual field instrumentation and monitoring data. From the field instrumentation data, the actual volume loss values were calculated. The compatibility of ground settlement and volume loss calculated using analytical and numerical methods and those measured using field instrumentation data is discussed in this paper.

Sep 1, 2022

By Matt Fenwick, Douglas R. Schwarm

Stringent underwater noise limits at the Fairview Ave. N. bridge replacement on Seattle's Lake Union required an innovative approach to supporting the 470-ft long drill trestle. Screw-in foundations would reliably mitigate noise, but the required 500-kip bearing resistance were an order of magnitude higher than typical helical piles. This paper describes the process of designing, installing, monitoring, and testing 22-inch dia. helical piles 80 feet long with 36- and 42-inch dia. helices. A static load test confirmed that the conventional k-factor design method can be extended to capacities of up to 800 kips. A 375 ft-kip drive mechanism had to be fabricated because no North American equipment could supply the necessary installation torque. Real time installation monitoring and later "re-torque" tests confirm that helical piles gain capacity with time, analogous to driven piles under restrike. Underwater and on-land measurements confirmed very low noise, suggesting the possibility of widespread adoption where similar limits are imposed. Overall, this case history illuminates the need for innovative deep foundation types in response to ever-increasing regulatory constraints.

Sep 8, 2021

By Rajasekar Subbian, Jessica Oudhof

In the Netherlands pile foundation design is done using CPTs in accordance with EC7 national annexure. The capacity per tip level is calculated for every CPT followed by zonation to find the tip level per zone. The correlation factors are used to take into account the variability in ground across the zone and they depend upon the number CPTs within the zone. The CPTs and pile tip levels selection for zoning is an iterative process that can demand significant manual effort to produce an economical pile plan. This often leads to the use of conservative correlation factors in order to accelerate the design process. Thus, it has been automated in a tool with CPTs, pile location and loads, and capacities as input. The tool has also been employed in two case studies and the results are compared to the current design practise.

May 1, 2022

By Lisa R. Papandrea, David Chen, Walter E. Kaeck

"Construction of the University at Buffalo’s new School of Medicine and Biomedical Sciences (UB-SMBS) required excavation in variable ground to a depth of more than 40 ft adjacent to the NFTA Metro subway and Allen Street Station. Complicating the building design and construction, the new medical facility incorporates the at grade Station entrance building, requiring a combination of temporary and permanent excavation support structures, a complex sequence of ground support installation, and a mix of shallow and deep foundations to accommodate the large floor spans and concentrated column loads introduced by building over and adjacent to the Station entrance. Excavation and foundation construction was challenged by a stratified soil profile with interlayered and sensitive sands, silts and clays and complicated groundwater regime with perched and regional water tables. Efficient construction required ongoing coordination between the design team and contractor, careful field observation, and construction monitoring in several facets of below grade construction. This paper describes the design and construction of excavation support structures and foundations to manage the variable ground, congested site conditions, and complications of building adjacent and above an active subway station. Use of site instrumentation and monitoring data to provide guidance in construction when unanticipated field conditions arise is illustrated. Lessons learned in installation and sequencing of excavation support, groundwater control and foundation construction are also discussed.INTRODUCTIONUniversity at Buffalo President Satish K. Tripathi heralded the new School of Medicine and Biomedical Sciences (UB-SMBS) as a future linchpin of UB’s downtown campus that will revitalize the area and enhance western New York’s emerging bio-sciences corridor. The $375 Million, 628,000 square foot, eight story building with two basements is expected to house 2,000 faculty, student and staff allowing UB to increase class size from 140 to 180 students. It will be constructed above the Niagara Frontier Transportation Authority’s (NFTA) Allen Street Station, creating a direct connection to Buffalo’s light rail system. The 200 ft x 400 ft site is bounded by Main Street, High Street, Washington Street and the Roosevelt Apartments and adjoining parking lot at the west, north, east and south respectively, as shown in Figure 2. Groundbreaking for the new building was in October 2013 with the facility scheduled to open in early 2017."

Jan 1, 2016

By Sowmiyaa. V. S., Tiruvengala Padma

Axial compression capacities of bored cast in situ piles as per Indian and International Standards are compared in this paper. Bored cast in-situ piles resting on soil and rock are considered for capacity assessment comparison. The standards considered for comparison are Indian Standards namely IS 2911-Part 1-Sec 2:2010 and IRC 78, International Standards like AASHTO LRFD Design-2017, API 2A WSD, BS 8004:2015 & EN 1997: Part 1:2014. The end bearing mobilization limits as proposed by various standards and their influence on longer piles in cohesive and cohesionless soils are discussed.

Sep 1, 2022

Jan 1, 2003

By Pathik Deb Mallik, Shyamal K. Mitra, Rajiv Kishore, Shuvranshu Rout, Manos De

"This paper presents a case study on the design and construction of a deep underground pit structure constructed inside almost a century old existing plant building. The complexity and challenge for the design and construction lay in executing the work in a difficult subsoil condition especially the presence of deep mica schist. The limited space availability in the existing plant for construction work without hampering regular production in other adjoining areas of the plant made the execution more challenging. Experience with difficult subsoil and proximity to old foundations entailed a non-conventional engineering approach while ensuring complete safety in spite of maintaining the normal operation.INTRODUCTIONTata Steel Processing and Distribution Limited (TSPDL) is a subsidiary unit of Tata Steel Limited (TSL) having a CR processing facility inside the premises of Tata Steel Limited. TSPDL intended to install equipment for a new slitting line inside the existing shed including construction of very deep structure called “loop pit” where the strips from cut CR sheets collect in the form of loops and are recovered as scrap. The entire plant is located within the shed of existing plant. The construction of all foundations including the loop pit is to be executed in the limited area without disturbance to normal production work in balance areas of the plant and also maintain safety and integrity of existing structures.The existing shed is an old structure constructed approximately 80 years ago. The building column foundations are gravity type design of brick masonry supporting only the vertical load from the columns. This type of foundation designed with no eccentricity of loading provides no allowance for implementing any foundation stabilizing design. The present project required civil construction for the new equipment foundations safely within this area."

Jan 1, 2015

By Greg Plutko

Laboratory testing has shown that the Marsh Funnel test can be significantly impacted by long-chain polymer entanglement. In general, shorter hydration time leads to more chain entanglement which in-turn, leads to higher marsh funnel values that values seen for longer mixing. This trend makes it very difficult to predict funnel-viscosity on successive days. Data is presented which helps to explain this chain interaction effect on Marsh Funnel data and how it differs from traditional Fann viscosity. The data suggest that this long-chain polymer entanglement occurs more in samples with less hydration time and decreases as hydration time increases. There is also suggestion that higher polymer concentrations have a greater drop-off in marsh funnel viscosity for a given aging length than do lower solids slurries. Fann rheology was shown to be much less impacted by the hydration time of the PHPA polymers than was Marsh Funnel viscosity. This suggests that the Marsh Funnel viscosity is impacted by some aspect of the slurry that does not affect Fann rheology as strongly. It is known from literature that longer-chained polymers have more potential to entangle and our data support the theory that the Marsh funnel viscosity is greatly impacted by this polymer-chain ‘roping’ entanglement.

By Paul Thurlow, Richard K. Lipscombe

The measurement of deflection of designed diaphragm walls is critical for near real time information to assess wall and soil behaviour as the internal area is excavated in a controlled manner. Data enables the site team and designers to check performance of the design, which is linked to safeguarding the site and the external stakeholders.This paper documents the use of Shape Accel Arrays at the Tottenham Court Road Western Ticket Hall during excavation and propping within the diaphragm wall for the Crossrail project. It shows how the data obtained was used within the site settlement management plan to assist in the control of the works and the information used for Value Engineering purposes that benefitted the project.The use of Shape Accel Arrays for measuring the deflection of retaining walls is not commonplace in the UK construction industry, with the Tottenham Court Road Western Ticket Hall being one of the first times they have been used in such a way. A detailed analysis of the data obtained from the instruments has been undertaken, and compared to the results obtained from the manual inclinometers that were read next to the SAAs. The advantages of the relatively new SAAs have been discussed, as well as other applications of the instrument.

Jan 1, 2017

By Reda Mikhail, M. Birkan Bayrak

The Washington State Department of Transportation (WSDOT) State Route (SR) 167/70th Avenue East Vicinity Bridge Replacement Design-Build project is located in Fife, Washington. This $40 million project consists of replacing the existing 70th Avenue Bridge over Interstate 5 (I-5) with a single-span bridge of about 220 feet long with approach embankments. The subsurface conditions along the new bridge alignment generally consists of alluvial deposits with high potential of liquefaction overlying glacially overridden deposits. In the early stages of the project, drilled shafts were considered as the deep foundation system; however, after an additional subsurface investigation is completed at the site, driven pipe piles were selected as the deep foundation system. Bridge abutments are supported by 24-inch diameter, 80-foot-long open-end driven steel pipe piles. The pile length was determined to bypass a relatively thick liquefiable zone and to tip the piles above what could be compressible soils. The use of advanced seismic analysis was instrumental in optimizing the pile length. The dynamic testing performed on numerous piles indicated what could be unique soil setup factors compared to those measured in local projects as well as those reported in national design manuals. Detailed discussions of the pile foundations design and construction is presented in this paper.

Sep 8, 2021

By Henry Zhang

This paper presents two case studies of large diameter driven tubular steel piles for the ongoing Woolgoolga to Ballina Pacific Highway upgrade (W2B). This project forms part of Australia’s largest regional infrastructure project and will upgrade about 155 kilometers of highway to four-lane, divided road. There are more than 170 bridges on W2B, and driven tubular steel piles are adopted on 43 bridges between Glenugie and Ballina. Driven piles terminating in soil or basalt is a big challenge faced by both designers and piling contractors due to 1) the uncertainty of expected pile unit shaft and base resistance in different soils; 2) whether plugging is formed; and 3) highly variable basalt strength and thickness near top of the rock. If these risks are not adequately managed during design or construction stages, it could lead to unexpected project delay, extra time and cost or pile toe damage in basalt. This paper describes two case studies, one for piles designed to terminate in soils and the other for piles designed to terminate in basalt. How these risks were assessed and managed during detailed design, procurement, hammer selection, pile installation and verification will be discussed in details with lessons learnt summerised in the conclusion.

Nov 1, 2022

By Keithe J. Merl, Brendan FitzPatrick, Gregg Piazza

Urban and industrial construction projects commonly involve interior work within buildings, warehouses and manufacturing facilities. Renovations of these existing structures must address both structural and geotechnical engineering challenges while also balancing the practicality of implementing solutions within site constraints including limited site access, overhead clearance restrictions, vibration tolerances and uninterrupted facility operations. This paper highlights two projects for an international shipping company where mezzanine level additions within active shipping facilities required construction of new foundations. Construction requirements included low vibration levels, as well as rapid and clean installation to limit impacts on the active shipping operations. The selected system also needed to adjust to both variable ground conditions and differing overhead clearances. This paper describes the installation, design and performance of Ductile Iron Piles used to meet the project challenges. The low vibration, driven pile system offered the ability to work within restricted overhead environments while successfully delivering working compression capacities ranging from 45 to 75 tons (41 to 68 tonnes) as well as lateral and tension resistance. The paper also presents the results of site-specific load testing (and pile capacity) for various termination criteria. INTRODUCTION Urban and industrial construction projects commonly involve interior work within buildings, warehouses and manufacturing facilities. Renovations of these existing structures must address both structural and geotechnical engineering challenges associated with the new construction. Foundation solutions must also balance the need to achieve design requirements with the practicality to be installed within the particular site constraints including limited site access, overhead clearance restrictions, vibration tolerances and uninterrupted facility operations.

Jan 1, 2019

By Marco Fellin, Van E. Komurka

Significant cost and construction benefits were obtained from performing a bi-directional static load test prior to construction on the Russell Street Bridge Replacement project in Missoula, Montana. The project utilized 24 drilled shafts to support two three-span bridges across the Clark Fork River. A bi-directional static load test (“BDSLT”) was performed on a large-diameter production shaft to demonstrate construction methods and confirm design assumptions. Subsurface conditions consisted of gravel with sand to a depth of 20 feet (6.1 m), underlain by gravel with sand, silt, cobbles, and occasional boulders. The test shaft had a nominal diameter of 5.9 feet (1.8 m), and an embedded length of 75.5 feet (23.0 m). The geotechnical engineer of record and the BDSLT test engineer collaborated to optimize the BDSLT jack assembly location within the test shaft, determine appropriate instrumentation locations, and plan the test protocol. The maximum applied test load was 10,707 kips (47.6 kN). Significant benefits were obtained from performing the BDSLT test, including 1) reducing each production shaft’s length by using a higher LRFD resistance factor allowed by having performed the testing, 2) using test-determined unit shaft resistances to evaluate and accept two production shafts that may have otherwise required remediation, and 3) providing the Montana Department of Transportation (and other designers) with increased presumptive unit resistance values in the gravel/cobble/boulder deposits. PROJECT DESCRIPTION The project was constructed in Missoula, Montana for the Montana Department of Transportation (“MDT”). The original bridge was approximately 60 years old, and consisted of a two-lane, 420-foot-long (128-m), four-span, riveted steel plate girder design spanning the Clark Fork River. The bridge was due for replacement owing to its deteriorated state, and the need for increased traffic volume capability afforded by a four-lane structure. HDR was the structural engineer. The preferred bridge alternate was a 459-foot- long (140-m), three-span, welded steel plate girder design. The new bridge was designed to meet current standards in accordance with MDT bridge design and AASHTO LRFD criteria. The new bridge was constructed in phases to keep traffic open during construction.

Jan 1, 2019

By Cem Altuntas

This paper is the second in a series of two describing the design and construction of a foundation for a major high-rise real estate development on the west side of Manhattan, N.Y. The foundation members consist of large-diameter rock-socketed caissons, driven closed-end steel pipe piles bearing on rock, and a secant-pile retaining wall surrounding the entire site. This paper focuses on the Osterberg cell (O-Cell) load test completed for determining the allowable side-shear resistance between the concrete and the sides of the rock socket. Different qualities of mica schist bedrock, demonstrated by the penetration of rock with the soil auger or drill casing, were encountered. Accordingly, an additional subsurface investigation consisting of test borings at each caisson location was completed. Unconfined compressive strength tests were performed on representative rock samples. The ?soft? mica schist was observed to have vertical foliations and high mica content. For the first time in Manhattan, an O-Cell load test was performed to determine the allowable side shear resistance for both the soft and hard mica schist bedrock. The side shear resistance obtained from the O-Cell load test is compared with the side shear resistance allowed by the New York City Building Code and empirical correlations using unconfined compressive strength values for rock. The rock socket design for the caissons was refined based on the O-Cell load test results.

Jan 1, 2008