Search Documents

By Luc Rombouts

The resources and reserves calculation of marine diamond deposits should be based on a systematic sampling grid. The distribution of the sample grade results tends to be very skew and has a large variance. A bias is easily introduced due to the fact that the grade distribution of the samples is very different from the grades of the area of influence. The temptation is always there to extrapolate the highest grade samples simply to their area of influence. If this is done, the higher grade areas will be systematically overestimated, while the lower grade areas will be underestimated. Such a bias should surely be avoided by weighing the sample grades in such a way with their neighbours, so that the estimated grades have a similar distribution as the grades of the blocks. The grade distribution of small mining blocks tend to be lognormal-like. If the coefficient of variation is known, i.e. the standard deviation divided by the mean, then the grade distribution of the small mining blocks is relatively well-defined. The distribution of the diamonds within the deposits can be simulated, based on the histogram of the sample results and on the semivariogram. The diamonds tend to cluster in trapsites. From the semivariogram and the histogram, the average size and spacing between trapsites, and the grade distribution within the trapsites, can be calculated using the model of the General Family of Discrete Distributions. Using such a simulated deposit, the grade distribution for different block sizes can be obtained. The grade distributions become more lognormal-like with increasing block sizes, as the trapsite effect is reduced.

Jan 1, 1998

By Anthony Wakefield

Dredging tends to be either horizontal or vertical. In each case solids have to be disengaged from the deposit, mobilized, acquired and elevated or translated. One means of elevation is the airlift. Elevation and translation of essentially granular material nay be by jet pump or centrifugal pump. Any of the three types may be used on its own. The airlift and jet pump may he combined for vertical transport and the centrifugal and jet pumps for predominantly horizontal. Both suction point and pipework must have a means of deployment from the surface or from a submerged vehicle or merely a diver. An airlift is an energetic system, having a source of energy and a means of storing it. It therefore will be difficult to prevent oscillation -surging. A centrifugal pump has a characteristic that bends over at low flow rate and is therefore intrinsically unsuitable for pumping solids. The result is blockage, operation at high velocity and correspondingly high wear rates or operation at low concentration of solids and correspondingly low efficiency. The jet pump is intrinsically exceptionally stable but has a low hydraulic efficiency. The jet pump-airlift hybrid prevents or reduces surging and increases system efficiency away from the optimum depth for airlift operation. Delivered solids concentration is increased. The jet pump-centrifugal pump hybrid totally prevents pipeline blockages and increases the productivity from a given pipeline size. For a given energy input the average production is typically doubled. For example, the Indian River Delaware bypassing pipeline transmits an overall day-in-day-out average of 500t/h (tonnes) of sand down a 10.86" diameter line.

Jan 1, 1998

By V. M. Hamza

Analysis of ground and airborne radiometric measurements in the Saquarema region (Rio de Janeiro) provides new insights into the breakdown and transport of mineral aggregates containing monazites, under sub-tropical weathering conditions. The breakdown process, accompanied by loss of low-density clay fractions in weathered materials is considered responsible for the observed patterns in relative enrichment of thorium and uranium along the migration paths of radionuclides. The characteristic features of these patterns provide clues as to the time and distance scales associated with processes of weathering and erosion. It is also possible to determine approximate locations of concentrations of accessory minerals. In this context, we advance the hypothesis that large under-water monazite deposits may be present along the offshore sand banks, in the coastal region of the state of Rio de Janeiro.

Sep 14, 2011

By Michael R. Gipp

Marine Mining Inc. is currently exploring for marine alluvial gold and diamonds on a prospecting licence over a concession that covers 10,000 km2 of the continental shelf of Ghana. The boundaries of the concession extend from 0 30'W to 2 40'W, and between the shoreline and approximately the continental shelf edge north of 4 30'N. This concession extends from Kikam Beach in the west, to Senya Beraku in the east, a distance of approximately 240 km, and seaward an average of about 40 km. The concession is entirely underwater, with the exception of the estuaries of the Ankobra and Pra Rivers. Ghana has been a large source of alluvial gold, with historical production exceeding 25 million ounces. Southwestern Ghana is characterized by Precambrian rocks, which have been folded into a number of NE-SW trending synclines and anticlines. The most significant feature of the Birimian rocks is the presence of evenly spaced gold-bearing greenstone belts. They are 10-15 km wide, separated by about 90 km, separate basins filled by folded metasediments and granitoids. The rivers that enter the concession drain most of the exposed gold-bearing belts of Ghana. Given that approximately 2 km of erosion has taken place since the Mesozoic, and that gold mines on these belts boast proven reserves of over 55 million ounces, it is likely that large amounts of gold have been eroded out and carried to the sea. Coastal fractures, related to Precambrian structures reactivated during Mesozoic rifting, are responsible for the physiography of the coastal area, which consists of high-relief horsts separated by grabens that have been occupied and infilled by rivers or by finer sediments during times of elevated sea level. These fractures were loci of gold mineralization during the Precambrian, and are the source of alluvial gold in rivers confined by them.

Jan 1, 1998

By Yuta Yamamoto

Seafloor massive sulfides (SMS) which contain Au, Ag, Cu, Zn, and Pb have been interested in as a target of commercial mining these 15 years. Japan has large potential of SMS and a national R&D project for the mining has been active these 5 years. However, the economy of SMS mining is very bad, because the waste tailing disposal cost is very expensive in Japan. A slurry flushing method is experimentally examined in this study for the improvement of the economy. During the flushing, because of density difference between the metal-rich ore and the waste rock, a kind of gravity separation is possible. The results suggest a possibility of the actual application.

Sep 14, 2011

By S. Hölz, M. Jegen, K. Reeck, A. Haroon

Past investigations of seafloor massive sulfides (SMS) focused on actively forming sites. New technologies are needed to explore for SMS deposits which have finished their active phase and are possibly covered by sediments or lava. For this purpose the new marine transient electromagnetic (TEM) induction system MARTEMIS was developed by GEOMAR. The system was used for investigations in the Tyrrhenian Sea (Palinuro Seamount) and at the Mid-Atlantic Ridge (TAG area) and proved to be suitable for operations at shallow (~600m) and great water depths (~3600m) in steep and difficult terrain. Calibration measurements in the water column demonstrate that it is possible to acquire high quality data, which is fit to be evaluated in terms of inversions. However, these calibration measurements also demonstrated that great care has to be taken in the design of such an inductive coil system, because relatively small metal structures attached to the system may lead to significant static distortions in the measured transients. The interpretation of TEM data acquired at the Palinuro Seamount show a conductive layer in the vicinity of a previously drilled, buried SMS occurrence and serve as proof of principle of the system. Results also indicate that the conductive SMS unit is indeed a confined layer with limited thickness between 3 – 5m, which was not known from previous drilling. In a similar manner, results also hint at an unknown mineralization at depth in a second area of the Palinuro Seamount. Investigations by TEM measurements were accompanied by measurements of the ambient electric field (→ self-potential) and seafloor temperatures with a heatflow probe as well as direct sampling with a gravity corer. The areal coverage of measurements and sampling allow for a greatly enhanced view of the structure.

Jan 1, 2018

By N. R. Ayupova

Several metallogenic zones including Sakmara, Magnitogorsk, and East-Ural zones were revealed in the Ural fold belt (Fig. 1). These zones are considered to be the paleogeodinamic sectors corresponding to marginal sea, island arc system, and uplift respectively. Ferruginous-manganiferous sediments in the Southern Urals are hosted by the basalt-rich volcano-sedimentary series of the Magnitogorsk paleoisland arc system with West- and East Magnitogorsk island arcs and Sibai inter-arc basin. The manganiferous mineralization occurs in association with the Middle Devonian stratabound hematite-quartz rocks and bedded red jaspers localized on the foot or handing walls of massive sulfide deposits. Fe-Mn nodules are widespread in jasper horizons on the flanks of manganese deposits. We have studied Fe-Mn nodules from the Faizulino and Yanzigitovo Mn-deposits formed in the Sibai inter-arc basin and compared them with well known Fe-Mn nodules from modern oceans.

Jan 1, 2010

By T. Semkova, G. Cherkashov, V. Rashidov, L. Anikeeva, G. Gavrilenko, G. Glasby

The Kurile Arc consists of at least 100 submarine volcanoes and 5 submarine calderas located mainly in the rear arc (Figure 1). The arc is seismically very active, particularly in the south, and is characterized by extensive volcanism and hydrothermal activity. At least one subaerial volcano on the arc (Medvezhy located on Iturup island) has an extremely shallow magma chamber and is intensely active.

By G. A. Tret’yakov, V. A. Simonov, I. Yu. Melekestseva, V. V. Zaykov, N. N. Ankusheva

The Kyzyl-Tashtyg massive sulfide polymetallic deposit is situated 120 km north-east of Kyzyl (the capital of Tuva Republic, Russia). It is located in the Ulug-O volcanic zone which is interpreted as the northern segment of the Kaa-Khem rift in Sayano-Tuva marginal sea, one of the Paleoasian Ocean margin (Fig. 1) [Zaykov, 2006]. Since its discovery in 1946 the deposit has been studied by many researchers. Significant information was published by Kuzebny et al. [2001] and Zaykov [2006] who proposed volcanogenic-sedimentary genesis. A single reference in English about Kyzyl-Tashtyg is available [Herrington et al., 1999].

By Hunsoo Choi, Sung Rock Lee, Ian J. Graham, Ian C. Wright

This is a part of the joint KIGAM-GNS-NIWA 3-year study of ferromanganese modules in the Campbell Nodule Field, east of Campbell Plateau to determine age distribution, growth rates and geochemical evolution in relation to geographic setting. The petrography, chemistry, inferred genesis, and 10Be/9Be dating of the nodules were described in the science report of GNS (Chang et al., 2003a, 2003b; Graham et al., 2003a) and presented at UMI (Chang et al., 2003c; Graham et al., 2003b). The morphology and distribution of ferromanganese nodules were also published in detail (Wright et al., 2005). This presentation is only concentrated on the mineralogy and chemistry of the nodules.

Aug 24, 2006

By Tetsuo Yamazaki

Natural methane hydrate has been scientifically studied as a carbon reservoir globally. However, in Japan, the potential for energy resource has been industrially highlighted. There is less domestic oil and natural gas resources in Japan, but many potential deposition areas for methane hydrate in ocean around Japan are the reasons. Less CO2 discharge from methane compared with coal, oil and conventional natural gas when the same calorie value we get is considered as the advantage for energy resource. However, because methane hydrate distributes in shallower sediment layer in ocean floor, accidental leakage of methane may occur while we utilize methane hydrate. Methane itself has 21-times impact on the greenhouse effect, if it reaches the atmosphere. Therefore, it is necessary to estimate the behavior in the environment after the leakage, if we want to use methane hydrate as energy resource. The mass balance after leakage of methane on seafloor and in water column is numerically studied through the analyses of methane emissions from natural cold seepages and hydrothermal activities in this research. The outline structure of mass balance ecosystem model shown in Fig. 1 is introduced. A numerical early diagenetic model CANDI (Carbon And Nutrient Diagenesis) developed by Boudreau (1996) for simulating the biogeochemical processes such as organic matter, oxidant, nutrient, bi-product, and pH diagenesis in aquatic surface sediments and C. CANDI improved by Luff and Wallmann (2003) for describing the formation process of calcium carbonates in CANDI are used as bases of the ecosystem modeling in surface sediment layer around seafloor methane emission. Two functions such as methane bubble dissolution and bacterial methane oxidation in water column are added to an existing physical plume dispersion model by Doi et al. (1999).

Jan 1, 2005

By Michael J. Cruickshank

The State of Hawaii has expressed concern over deterioration of the tourist beaches at Waikiki, which are becoming seriously depleted of sand. In this report the options for acquisition, transportation and placement .of sand on the beach are examined with respect to feasibility and cost. Ten sources of sand were compared, including commercial, from Australia, Maui, and Barbers Point (3), deposits offshore of the Reef Runway (3), offshore of Waikiki (3), and offshore of Molokai from the Penguin Bank (1).

Jan 1, 1991

By T. Barryere, R. B. Pedersen, E. Reeves, A. Stensland, I. Thorseth, T. Baumberger

Venting on ultraslow spreading ridges is far more abundant then previously predicted, and the discrepancy between observed and predicted vent field density may imply that non-magmatic heat sources are common along these ridges (Baker and German, 2004; Escartin et al., 2008; Rona et al., 2010; German et al., 2016). In this study we have estimated the flux from two hydrothermal vent sites situated on the slow to ultraslow spreading Mohns Ridge at the Arctic Mid-Ocean Ridge system (AMOR). The flux estimates have been made using the primordial isotope 3He in the non-buoyant plume above the Loki’s Castle vent field at the northern termination of the Mohns Ridge, and from the Jan Mayen vent fields area situated close to the southern termination of the ridge. Primordial 3He enters the oceans through degassing and mixing with hydrothermal fluids eventually to be discharged at the ocean floor primarily at hydrothermal vent sites and submarine volcanic eruptions (e.g. Clarke et al., 1969; Lupton and Craig, 1981; Lupton, 1998). Once introduced into the water column the concentration will only decrease by dilution due to its conservative behavior in the water column. Water column samples were collected using a CTD (conductivity, temperature, depth) probe (911plus Seabird) with a Niskin water bottle rosette. The water column above the Jan Mayen vent fields (JMVF) was sampled in the years 2006, 2011, 2012 and 2013 (82 samples) and the water column above the Loki’s Castle vent field was sampled in the years 2007, 2008 and 2009 (116 samples).

Jan 1, 2018

By RB. Pedersen, T. Barryere, E. Reeves, A. Stensland, I. Thorseth, T. Baumberger

Venting on ultraslow spreading ridges is far more abundant then previously predicted, and the discrepancy between observed and predicted vent field density may imply that non-magmatic heat sources are common along these ridges (Baker and German, 2004; Escartin et al., 2008; Rona et al., 2010; German et al., 2016). In this study we have estimated the flux from two hydrothermal vent sites situated on the slow to ultraslow spreading Mohns Ridge at the Arctic Mid-Ocean Ridge system (AMOR). The flux estimates have been made using the primordial isotope 3He in the non-buoyant plume above the Loki’s Castle vent field at the northern termination of the Mohns Ridge, and from the Jan Mayen vent fields area situated close to the southern termination of the ridge. Primordial 3He enters the oceans through degassing and mixing with hydrothermal fluids eventually to be discharged at the ocean floor primarily at hydrothermal vent sites and submarine volcanic eruptions (e.g. Clarke et al., 1969; Lupton and Craig, 1981; Lupton, 1998). Once introduced into the water column the concentration will only decrease by dilution due to its conservative behavior in the water column. Water column samples were collected using a CTD (conductivity, temperature, depth) probe (911plus Seabird) with a Niskin water bottle rosette. The water column above the Jan Mayen vent fields (JMVF) was sampled in the years 2006, 2011, 2012 and 2013 (82 samples) and the water column above the Loki’s Castle vent field was sampled in the years 2007, 2008 and 2009 (116 samples).

Jan 1, 2018

By Daisuke Monoe, Kisaburo Nakata, Rika Takeuchi, Tetsuo Yamazaki, Tomoaki Oomi, Tomohiko Fukushima

There are generally two methane passes in conjunction with the seafloor natural cold seepages, as is schematically shown in Fig. 1. The first pass consists of the coupled anaerobic oxidation of methane and anaerobic sulfate reduction, as well as sulfur oxidation in the bacterial mats and immobilization thereafter in the sediment layer and on the seafloor. Through the first pass, calcium and organic carbonates are formed in biological and chemical processes from the methane (Luff and Wallmann, 2003; Luff et al., 2004). The detailed structure of the seafloor methane consumption process unit and its biological and chemical processes were introduced in Yamazaki et al. (2005). The other pass consists of direct bubbling into the water column. Through this pass, organic carbonate is formed with biological oxidation, and a small amount of the methane escapes into the atmosphere. Methane flux is supplied to these two passes through the sediment layer from the deeper structures. The structure of the methane supply process unit was introduced in Yamazaki et al. (2006).

Sep 24, 2006

By Irina A. Pulyaeva

Hydrogenetic Fe-Mn crusts are ubiquitous in the ocean basins and play an important role in marine mineral-deposit research because of their widespread occurrence and high concentrations of valuable and rare metals. Directed research, which started in the last quarter of the 20th century, has provided significant results, with substantial amounts of data produced on Fe-Mn crusts structure, composition, and distribution in the global ocean. Detailed study of several seamounts has given confidence about the scale of Fe-Mn crust development and their characteristics. Now, commercial interests gain more and more attention. However, at the same time some theoretical questions related to Fe-Mn crust history including controls on metal sources and concentrations have not yet been answered. Here, we present the overview of age, composition, distribution, and geological setting of hydrogenetic Fe-Mn crusts from Pacific and Atlantic seamounts and discuss the geological evolution and conditions that led to the formation of potentially economic concentrations of metals. The age, composition, and distribution of Fe-Mn crusts in the Atlantic and Pacific oceans were determined by using a Fe-Mn deposits database compiled from our original data, published papers, published databases, and other international sources. Comparative analysis of Fe-Mn deposits from the Atlantic and Pacific oceans shows that there are similarities in basic characteristics of crust formation in both oceans. Simultaneously, there are significant differences in the scale of Fe-Mn crust distribution and composition that can be explained by differences in geological settings and characteristics of the deposition environment.

Jan 1, 2011

By Andrea Koschinsky, Luise Heinrich

(for an oral presentation) Activities for preparing future deep-sea mining offer the unique opportunity to study environmental conditions and anticipate adverse environmental impacts prior to the commercialization of the activity. Until know, environmental research has first and foremost focused on understanding direct impacts occurring at the seafloor or in the water column such as the removal of substrate, the suspension of sediment or the creation of particle plumes. Impacts occurring above the sea surface have thus far rarely been considered. The operation of deep-sea mining equipment, as well as of mining and transport vessels will be associated with a considerable energy demand. In the open ocean, this energy will be provided by heavy fuel oil (HFO), which is the cheapest and most common marine fuel. The combustion of HFO will be associated with the release of greenhouse gases and other pollutants. Deep-sea mining will thus directly add to already critical air pollution levels caused by international shipping. To contribute to a holistic assessment of deep-sea mining impacts and to address the previously outlined knowledge gap, we present the methodology to quantify the fuel consumption and associated emissions of a potential typical commercial manganese nodule mining operation in the Clarion-Clipperton Zone (Fig.1). Using the mine set up and energy demand estimates from a study commissioned by the German Federal Ministry of Economic Affairs and Energy supplemented by information from literature, we anticipate emissions of carbon dioxide (CO2), carbon monoxide (CO), methane (CH4), nitrous oxide (NO2), nitrogen oxides (NOx), sulfur oxides (SOx), particulate matter and non-methane volatile organic compounds.

Jan 1, 2018

By Øystein Sture, Kurt Aasly, Ben Snook, Sigurd A. Sørum

INTRODUCTION Efficient exploration methodologies for base metal deposits have huge benefits for future deep sea mining endeavours, and underwater hyperspectral imaging (UHI) has been variably demonstrated to have applications in the identification and characterisation of mineralisation on the seafloor for both nodules and seafloor massive sulphides (SMS) (Dumke et al., 2018 and 2017 respectively). Due to growing resource requirements (Singer, 2017), SMS deposits are considered to be increasingly significant sources of copper and zinc, as well as silver and gold. This style of mineralisation is currently occurring at active hydrothermal vents (black and white smokers) but now-inactive sites also have the potential to be large mineral deposits. As such, the development of novel methodologies to detect both on-going and extinct mineralisations are of high importance. Geological setting During the MarMine cruise (Ludvigsen et al., 2016), non-mineralised host rock, low grade ore and high grade ore grab samples (Snook et al., 2018) was collected by ROV from the Loki’s Castle deposit (Pedersen et al., 2010), located on the Mohn’s/Knipovich junction on the ultra-slow spreading Arctic Mid-Ocean Ridge (AMOR), at a depth of approximately 2300 m. This material has been characterised as part of the MarMine project (e.g. Snook et al., 2017), and, by imaging compositionally constrained material, the measured hyperspectral responses can be used to generate a library for identification of deposits on the ocean floor. UHI technology Remote sensing with hyperspectral and multispectral technologies has seen wide use in prospecting for ores and hydrocarbons on land (Van der Meer et al., 2012). Iron oxides and sulphides have low blue reflectance and high red reflectance in the visible spectrum. The ratio between these two pairs has been used in exploration for terrestrial deposits of hydrothermal origin (Sabins, 1999). This discrimination typically also includes wavelengths exceeding the visible spectrum (1.5µm – 2.5µm). These wavelengths are typically not utilised underwater because infrared wavelengths and higher are rapidly attenuated in water. However, discrimination based on the full shape of the spectral response in the visible light (350nm – 800nm) may still be possible (Bolin and Moon, 2003). Resolving the endmembers from the spectral responses requires prior knowledge about the optical properties of the materials, i.e. their reflectance. These reflectances can be obtained in a controlled environment, where the spectra of the lamps, wavelength- dependent attenuation in water and scattering of light can be accounted for (Johnsen, 2013).

Jan 1, 2018

By Hyung-woo Kim

This paper concerns about steering characteristics of pilot mining robot, named MineRo II, crawling on extremely cohesive soft soil using dynamic simulation software. The MineRo-II for deep-seabed manganese nodules, which aims at the use for pilot mining test, was manufactured in 1/5 scale of commercial mining capacity (see Fig. 1).

Sep 14, 2011

By I. Yu. Melekestseva, V. V. Zaykov

Paleooceanic structures of the Urals fold belt contain different volcanic-hosted massive sulfide deposits of the Urals, Kuroko and Cyprus types [Prokin, Buslaev, 1999]. Small Cobearing massive sulfide deposits, as Ishkinino, Ivanovka and Dergamysh, associated with ultramafites of the Main Urals fault, are less known. Interest to them had arisen after discoveries of the modern “black smokers” associated with ultramafic rocks of the Middle-Atlantic Ridge (MAR). Ores of the Urals deposits are enriched in Co (0.3 %) and Ni (0.6 %) that are concentrated in Co-Ni-Fe-sulfides, sulfarsenides, and arsenides. Ores also contain the increased gold contents – 3–6 ppm and up to 16 ppm in those saturated with As-bearing minerals. The aim of the paper is a comparison of precious metal mineralization in ores from the Paleozoic and modern ultramafic-hosted massive sulfides.

Aug 24, 2006