Search Documents

By S. H. Morar

Froth flotation is a physico-chemical separation process that takes place in two phases; pulp and froth phase. It is widely recognised as a complex process, due to the range of interactions present within the system. Of critical importance is the role of the froth phase within the system. The pulp kinetics governs the maximum potential recovery within a flotation cell, while the froth phase governs the selectivity via the froth?s stability. Higher froth stability improves recovery at the expense of grade, and lower froth stability improves selectivity. It is well known that the two major factors affecting froth stability are attached particles and solution chemistry. This paper looks at a flotation bank at different froth depth and frother concentrations. The air recovery to the concentrate is determined at each condition and relates the effect of the operating conditions on froth stability and transport to the amount of solids that are recovered to the froth and concentrate by true flotation. The results presented show that, for a given process objective, which in this case was a consistent mass pull profile, depending on the operating conditions, solids recovery in the pulp is affected by the air rate required to maintain the target mass pull. To a smaller extent, the changes in the pulp composition affect down-stream pulp recovery. The variation in solids recovered into the froth drives the froth stability at the start of the flotation bank, while the frother drives the froth stability at the end of the bank. The performance in between these two extreme conditions arises from an interaction of these two effects. The consequences of these interactions can give rise to counter-intuitive responses that can confound efforts to optimise the performance of the bank.

Jan 1, 2014

By Y. H. Tang

For its surface features, micro-sized hematite is usually difficult to recover by magnetic separation; especially, the existing high gradient magnetic separator in industry can not utilize collecting matrix with thin silky rods for its property of being easily blocked; the lower size limit for recovery of micro-sized weak magnetic minerals is about 0.019mm, some even is 0.037mm. This paper introduces the application of the combined new technique of water-air joint discharging of concentrate and collecting matrix with different diameter silky rods in the field of recovery of micro-sized hematite by high gradient magnetic separator. The commercial test result for recovery of a certain hematite with size about ?0.037mm shows that the recovery can be promoted by 16.81% with basically same concentrate grade.

Jan 1, 2014

The characteristics of mineral resources and tailings resources in China are analyzed. Those tailings, which have double characteristics, can occupy land, pollute environment and even influence human habitat if they are not disposed in time. So pay attention to the comprehensive utilization of the tailing more and more both at home and abroad. The present situation and problems in comprehensive utilization of iron tailings in China are introduced by combine some practice experience, and have looked forward to the comprehensive utilization of iron tailing situation.

Jan 1, 2014

By R. Marandi

Biosorption of heavy metals can be an effective process for the removal of heavy metal ions from aqueous solutions. In this study, the adsorption properties of nonliving (boiling in NaOH) biomass of phanerochaete chrysosporium. For Pb (II) and Zn (II) were investigated by using batch adsorption techniques. The effects of initial metal ion concentration, initial pH, biosorbent concentration, stirring speed, effect of temperature and contact time on biosorption efficiency were studied. Experimental results indicated that the uptake capacity and adsorption yield of one metal ion were reduced by the presence of the other metal ion. In the experiments the optimum pH value was found out 6.0. The experimental adsorption data were fitted to the Langmuir and Frundlich adsorption models. The highest metals uptake was calculated for Zn (II) and Pb (II) were 57 and 87 respectively. desorption of heavy metal ions was performed by 50 mM HNO3 solution. The results indicated that the biomass of p.chrysosporium is a suitable biosorbent for removing heavy metals ion from aqueous solution.

Jan 1, 2014

By H. Allenius

Today, most requests for quotations force all bidders to follow the bid document to the letter. The choice is then made based on price since it is the only difference in technically identical offers. However, clients allow and even encourage suppliers to come up with alternatives. Overall economy again, is much more than low investment costs. Operation costs may affect the economy of a project far more than a million saved in investment. There is almost always the choice: Should we go for the cheapest solution or should we go for the most economical solution? We strongly recommend the study of the long-term effects on investments as they often surpass any apparent savings in capital expenditure. With high operating costs, time is never on our side. Almost all relevant inputs and outputs in a concentrator have a value that can be expressed in a suitable currency. Unit prices may differ substantially from one operation to the other, but everything has a price tag and globalization has made it possible to move both goods and services to almost any place in the world. Even a rather simple exercise can give a good indication on which process improvements are worth pursuing when investing in new systems or equipment. The ones that do not qualify, as money earners, will naturally appear as clearly. No ?rocket science? is required, just process knowledge, practical experience, an open mind and some common sense and the reward may be the difference of having a good or an excellent project. The model we have developed can be made as detailed as required, but we do not recommend too much detail, as it sometimes tends to distract work and obscure the important issues. Two different process solutions compared in a simplified example illustrate the importance of evaluating a project based on its long-term effects rather than focusing on the investment costs only.

Jan 1, 2014

By F. Göktepe

Flotation gases and conditioning of the pulp with them are one of the important parameters of flotation and should be taken into account especially in the flotation of sulphide ores. In this study, flotation of pure chalcopyrite and pyrite samples were investigated with air, oxygen and nitrogen as flotation gas and the effect of conditioning with these three gases also were performed. Flotation gas was introduced for 5min, 10min, 15min and 20 min. For chalcopyrite flotation there was no drastic change in recovery when air, oxygen and nitrogen were used as flotation gas but conditioning the pulp with oxygen for 10 minutes increased the recovery about 8% where pulp potential has been approximately 25 mV with chalcopyrite and 150 mV with platinum electrodes. Conditioning with all three gases decreased the pyrite recovery by about 20% with 20 minutes conditioning. Pulp potential decreased in the presence of nitrogen while conditioning with air and oxygen increased the pulp potential for both electrodes. Generally potential increased for both minerals with oxygenation and aeration time but it was stable or slightly decreased with nitrogenation. Comparison of the gases showed that the different flotation gases do not effect flotation recovery but conditioning the pulp with these gases at pre-flotation effects chalcopyrite and pyrite flotation recovery, most dramatically pyrite.

Jan 1, 2014

By H. H. Li

Reverse flotation is usually used for hematite/silica or bauxite/clay flotation separation in which the silica or clay is floated and rejected. Some properties of these silicate minerals such as particle size and surface characteristics have significant effect on their flotation behaviours. Firstly, the silicate mineral particles (especially clay minerals) generally have fine particle size (< 5 microns) in their natural states or due to overgrinding and they display poor flotation kinetics, consequently having low flotation recovery. Secondly, the wettability difference on different particle basal planes influences the affinity for adsorptions of different types of chemicals such as collectors or macro-molecule. Common polyacrylamide (PAM) flocculants can be used to minimize the exposure of the most hydrophilic planes of clay particles via hydrogen bonding but they can not efficiently enhance the overall particle surface floatability due to the hydrophilic properties of this type of macromolecules. A novel method to improve both flotation kinetics and surface wettability of silicate minerals has been developed and studied. That is to use a temperature-sensitive polymer, poly (N-isopropyl acrylamide) (PNIPAM), as a process aid in the flotation of silicate minerals. Unlike PAM polymers, PNIPAM can induce a hydrophilic/hydrophobic transition on the particle surface when the temperature is changed to be lower or higher than its critical solution temperature (CST). At a lower temperature, the PNIPAM adsorbs on the particle surface via hydrogen bond similar to PAM. It induces strong hydrophobic aggregation when the temperature is increased above the CST. Thus, both floc size and mineral floatability are greatly increased. The flotation results show very good flotation performance and the addition of conventional flotation collector was no more required because the increased particle surface hydrophobicity induced by PNIPAM. Contact angle measurements explained the role of PNIPAM in manipulating particle surface hydrophilic/hydrophobic transition.

Jan 1, 2014

By Ingvar Ymén, Alexandra Lundmark

"The depressive effect of dichromate on galena was evaluated with chemical experiments and small-scale depression experiments at a pH of around 12. The depressive effect was measured with Dynamic Vapor Sorption (DVS), which measures the water uptake of a sample as a function of the % relative humidity. The depression is due to PbCrO4PbO, which in the presence of Ca2+ and SO4 2- forms a more or less amorphous solid solution (Pb,Ca)(CrO4,SO4)PbO, which clogs to the surfaces of the ore. Free Pb2+- ions are needed for depression to occur and at high pH Pb2+ - hydroxide complexes, supply enough Pb2+ - ions to precipitate (Pb,Ca)(CrO4,SO4)PbO. In air CO2, precipitates CaCO3 which slowly lowers pH, precipitating more (Pb,Ca)(CrO4,SO4)PbO and CaCO3 on galena. Similar experiments where performed with five alternative depressors whereof phosphate, which forms an amorphous precipitate of approximate composition Pb3Ca13(PO4)10SO4, gave the best results. Phosphate was tested in laboratory scale flotation experiments giving encouraging results.INTRODUCTIONWithin Boliden Mines, concentrating of copper and lead from complex sulfide ores is performed by bulk flotation, meaning that copper and lead are concentrated in the same product. Downstream, copper and lead are separated by flotation of chalcopyrite, and depression of galena. Boliden has for many decades used sodium dichromate to depress galena (reference 1). Dichromate is both toxic and carcinogenic and Boliden has for many years investigated several alternatives. So far, however, the best results have been obtained with dichromate. Since Boliden has tried to substitute dichromate for a long time without finding a process as effective, Boliden decided to clarify the function of dichromate in the depression of galena and on the basis of the outcome find alternative depressors with similar function. This study was given to RISE Bioscience and Materials / Surface, Process and Formulation as a consultancy assignment. This paper presents the outcome of the combined efforts of Boliden and RISE."

Jan 1, 2018

By R. ?. Shishmarjov, Yu. ?. Davidenko, S. V. Bukhalov, ?. S. Baksheev, M. S. Shkirya, N. ?. Aikasheva, D. V. Bogdanovich, ?. Yu. Faustova

"The goal of prospecting operations in the Republic of Altay was to locate gold-sulfide-quartz mineralization. For this purpose we applied the technology of electromagnetic sounding and induced polarization (EMS-IP). These operations resulted in localizing promising sites with presence of sulfidization. The EMS-IP method proved to be highly efficient amongst other prospecting methods targeted at recognizing zones of sulfide mineralization making up 91%, considering that in more than half cases the ore intervals were the case. In the Yakutian diamondiferous province the EMS-IP technology was approbated during three field seasons to accomplish the assignments on searching for kimberlite bodies under conditions of various geological types. As a result, the reference objects were distinguished, and geoelectric parameters of kimberlite pipes of explosion were defined.INTRODUCTION In the time span 2015-2016 in Gorny Altay the EMS-IP technology was approbated in the Novokuznetsk area. The on-land areal geophysical survey was performed by EMS-IP method applied to identify, outline and locate promising sites with Au-Ag-bearing polymetallic mineralization within surveyed areas. Compared to the hosting rocks, the sulfides contained in polymetallic mineralization are typified by low specific electrical resistivity (SER) and high polarization. The areal survey conducted via EMS-IP method provided spatial characteristics of searched object. From July 2016 to August 2017 our expedition group carried out serial test works and laboratory investigations intending to define performance capabilities of EMS-IP technology in searching for kimberlite bodies under conditions of diverse geological types. The prerequisites for serial work were operations accomplished at the «Listvenichny» site lying 35 km away from Mirny town in the Sakha Republic (Yakutia), where the EMS-IP technology was probed for locating position and measuring geoelectric parameters of tuff pipe «Buardakhsky». After successful completion of operations it was decided to evaluate geoelectric parameters of kimberlite pipes of explosion."

Jan 1, 2018

By G. Belardi

This paper presents the preliminary results of a research programme conducted to assess the feasibility of a flotation technique in the remediation of soils severely affected by heavy metal contamination. The use of flotation in soil remediation is a recent practice. The main difficulties are given by the variety and peculiarity of the heavy metal containing species, and also by the grain size. Most of the studies reported in the literature concern the use of conventional collectors, such as xanthates, after a preliminary chemical modification of the metal bearing species through sulphidization. On the basis of the minera-petrographic characterization and of speciation, some classes of reagents have been selected, capable of acting both on metal-bearing species and all metallic cations to be separated. The design of the synthetic molecules has been based on the coordinative properties of the metallic centres and functionalized in order to act as collectors for a wide range of metals independently on their surrounding atoms. In laboratory experiments a sample of stream sediment has been utilized, whose contamination is caused by the runoff from Sardinia mine waste dumps and overflow from the settling ponds. The material showed contamination mainly from Zn, Pb and Cu and to a lesser extent from Cr, Ni, Cd, and Sb associated in mixed particles of Fe and Mn. Flotation tests on a laboratory scale have been performed on grain sizes less than 355 µm in laboratory cell Minerais & Metaux. The effects of the structure of collectors (functional group, chain configuration) as well as of the principal flotation parameters (such as pH, concentration of reagent) on the grade and recovery of heavy metals in the concentrate and in the tailings (remediated soil) have been investigated. The results of the laboratory tests substantially confirm the theoretical premises, and the most effecive reagents found belong to the classes ATP, MBT, MBO, fat acids and phosphates.

Jan 1, 2014

By J. H. Zhang

An atomic force microscope has been used to measure the forces acting between two silica and two rutile surfaces in the presence and absence of cationic surfactants, CnTACl (n = 12~18). The forces measured in the absence of surfactant can be fitted to the DLVO theory. At short separations, however, the silica surfaces exhibited repulsive hydration forces, while the rutile surfaces did not. On the other hand, the forces measured in the presence of the cationic surfactants show long-range attractions that are larger than the van der Waals forces. The long range attractions are the strongest at of the point of charge neutralization (p.c.n.), which decreases with increasing surfactant chain length. The possible origin of the long-range attraction has been tested in view of the charged-patch model of Miklavic et al. (1994). However, the sizes of the patches back-calculated from the model were much larger than those the patches (or hemi-micelles) determined experimentally and reported in the literature. It is, therefore, suggested that the long-range attractions observed in the present work are due to the structural response of the water molecules in the vicinity of hydrophobic surfaces.

Jan 1, 2014

By H. R. Manouchehri

"In all electrical beneficiation methods, the difference in electro-physical properties of the contributed mineral particles, essentially frictional charge, electrical conductivity and dielectric constant properties are exploited to achieve separation. The composition of the raw material determines what kind of either corona charging, conductive induction, or triboelectric separation method should be employed. The process is versatile and is influenced by different parameters related to mineral characteristics, surrounding ambient conditions and electrical and mechanical attributions of the separating device. Electrical separation is surface based beneficiation method which is mainly affected by the surface and surface changes of the minerals. Therefore, it is essential to understand how the electrophysical properties of the minerals can be changed/modified. During electrical/electrostatic separation process, both charge magnitude and its polarity that developed on the particles and therefore, their electrical beneficiation potential is essentially defined by surface phenomena. Therefore, it is essential to understand how the main electro-physical parameters can be changed/modified with applied surface treatment/pretreatment methods to promote separation. Surface treatment of minerals is carried out by different means, including chemical conditioning, irradiation, thermal treatment, etc. This paper discusses and analyze the electrical separation process, electrophysical properties of the minerals with special focus on the effect of surface pretreatment/treatment methods to affect electrical beneficiation potential of the minerals. The surface treatment methods vary in a wide range from simple surface cleaning to more complicated chemical conditioning and doping. The knowledge of the solid-state physics and chemistry leads to improve the beneficiation potential of different mineral systems by choosing suitable treatment method(s). Despite the complexity and multiplicity of the charging mechanisms, difficulties in separating fines it seems to be beneficial make our attempts to further investigate and develop the process as dry, low cost beneficiation process, especially nowadays when environmental concerns, as well as energy and water consumptions are main concerns for mining industry."

Jan 1, 2018

By Y. Q. Yang

Jig is a kind of conventional and old gravity concentration equipment, which is mainly used in the preconcentration of medium particle fractions of low-grade nonferrous metal ore. In the past ten years, studies on jigs have made a great progress on separation of coarse and fine particle fractions. At the same time, pneumatic jigs have been widely used in processing of nonferrous metal ore. In this paper, pilot test study and commercial operation for several kinds of jigs used in Dachang con-centrator has been introduced. Dachang mining area of GuangXi province is rich in mineral resources, where many minerals exhibit various complex properties. Many elements such as Sn, Pb, Sb, Zn, S, As, Cu, In, Ag, Gd, Ag, Ga, etc, were found in the run-of-mine ore (ROM). At present, Dachang concentrator produces tin concentrate, lead-antimony concentrate and zinc concentrate. Other valuable elements get enriched and recovered in above concentrates. Dachang Mine with a mining operation history more than sixty years will end its mission on the rich ore resource exploitation. At present, low grade ores are porcessed in the concentrator, and the concentrator begins to run at a loss upon processing the low-grade and refractory ore. Heavy medium cyclones were used in the concentrator for processing 20-4mm fraction, Gongge jigs for 4-2mm fraction, and cone concentrator combined with spiral concentrator to discard the tailings of -2mm fractions. In order to minimize overgrinding, table flotation was used to recover some liberated cassiterites in a complex processing technology. Therefore, the concentrator is difficult to manage. Many years studies have shown that heavy medium cyclones and spiral concentra-tors can be replaced by sawtooth shaped wave jigs to discard 50% tailings to improve the grade of feed. And the feed was divided into rich one and poor one to minimize overgrinding of valuable cassiterites with different grinding mills. In this case, the recovery of the valuable minerals can get improved and the flowsheet was simplified. Moreover, the concentrator begins to make profit with reduction of cost. At the same time, pollution in the concentrator gets reduced and the working condition gets improved too. Sawtooth shaped wave jig was used in Changpo concentrator for replacement of cone separators and spiral concentrators to discard the tailings of -4mm fraction, and the yield of discarded tailings got improved from 30% to 50%. Grades of tin, lead and zinc in the tailings are lowered from 0.15%, 0.12%, 0.7% to 0.06%, 0.05%, 0.4% respectively, with a loss reduction of tin, lead and zinc from11%, 9%, 10% to 7.5%, 6%, 5% respectively, corresponding to the increasement of recovery of tin, lead, zinc from 52%, 50%, 55% to 56%, 56%, 62% respectively. Cost of the concentrator for processing one-ton ROM was therefore dropped from RMB155.28 to RMB119.74. Changpo concentrator lost RMB2.5 million in 2003, but it made a profit of RMB0.92 million in 2006 after the innovations. Batac jig was used in Tongkeng concentrator to discard the coarse tailings at 20-4mm, with a discarded yield of 35%, and the grades of valuable minerals got improved with a recovery above 95% for tin, lead-antimony and zinc.

Jan 1, 2014

By P. S. Rao

In 1951, Tata Steel became the pioneer in Asia by setting up its first ever washery in West Bokaro Colliery. The first beneficiation plant used to produce clean coal of 19% ash with chance cone. Feed size of chance washers were -75 mm to +6 mm. The fine coal (-6 mm) were used directly. With change in technology,in 1986,chance cones were replaced by DM cyclones and coal was washed in two circuits. In the coarse circuit -13 mm to +0.5 mm coal was washed in two stages while the fine coal of -0.5 mm was treated in froth floatation cell. With further improvement in the process the higher ash raw coal was feed to produce clean coal of 13% ash. In 1998, DSM cyclones were replaced by scrolled Evolute design cyclone which has Ep of 0.020 to 0.025 ranges resulting in increase efficiency of separation. With the increase in demand of clean coal, lower seam proportion has increased in raw coal production. The washability studies of individual seams indicated large difference in the seam characteristics in terms of washability and specific gravity cut points of the individual seams. So washing all seams together had resulted in frequent change in the character of coal and warrants frequent changes in the operating parameters of the plant in which the separating efficiency comes down and ultimately resulted in yield loss initially. With increase in knowledge and experience in coal washing the solution to this problem was achieved by adopting, seam-wise washing which is enabling process engineers by keeping set point for longer periods there by to enhance the separation efficiency. Keywords: coal processing, froth floatation, steam washing

Sep 1, 2012

By Sumantra Bhattacharya

The per capita energy consumption in India is 510kgoe/year, the global average being nearly 1818kgoe/year. Correspondingly low is the per capita CO2 emission at 1.25t against the world average of 4.39t.65-70%, at times more, of India?s power generation from about 190,000 MW installed capacity, is however coal fired.India therefore has to secure diversified sources of energy and solar power is increasingly being looked as the real alternative to the existing over dependence on coal. To ensure sustainable solar power it is essential to secure its raw material base that is ?silica?, hitherto considered as ?minor minerals?. That calls for immediately addressing the issues of land availability, solar power cost, developing a dynamic inventory of silica containing minerals, appropriate processing technology and strong regulatory framework for sustainable mining and processing of all silica rich minerals. Keywords: silica, silicon, Thar, power generation, India, quartz, solar power

Sep 1, 2012

By A. R. Hasankhoei

Water recycling is of prime importance in mineral processing due to consumption of large amount of water. This issue is vital in areas with a low rainfall such as Shahre-Babak (Kerman, Iran). Deep cone thickeners, unlike conventional thickeners, have a low diameter to height ratio where large amounts of flocculants are used to increase particles settling rates. The high bed heights (over 10 m) produce enough pressure to create a paste type underflow indicating maximum water recovery. Flocculent preparation, conditioning, and distribution along with the bed height are among the important factors affecting the performance. Four deep cones are used to recover water from the tailings of the plant. Plant data indicated that the thickener never reached the target underflow percent solids (63%) and the average underflow concentrations were between 49 and 57%. By modification and optimization of flocculent preparation and distribution methods the underflow percent solids increased by 3-4%. This translated to an increase of water recovery from 67 to 73%. This was equivalent of 53000 m3 saving in monthly water consumption. Keywords: deep cone thickener, water recovery, flocculant, copper tailings

Sep 1, 2012

By M. J. Lottering

Gold deposits in South Africa are invariably associated with uranium bearing minerals. Although it is low grade uranium by international standards, averaging around 0.3 kg U3O8 per ton of ore, recovery of uranium as a by-product improves the overall economics of gold extraction. Moreover, the current high uranium prices as well as increased demand due to renewed interest in nuclear power provide significant incentives for dedicated uranium production. An understanding of the uranium leaching response to changes in operating conditions is an important first step to-wards optimisation of uranium recoveries. In South African acid leaching plants, uranium dissolutions higher than 90% are difficult to achieve, and the chemical origin of this limit is not clear. To study leaching behaviour, an important consideration is the mineralogical characteristics of the ores. Typically, a diagnostic leaching approach can be followed. In this paper, a mineralogy-leachability explanation is presented to rationalise the difficulty in exceeding 90% dissolution from low grade uranium ores on the basis of a simple diagnostic leaching method. It was found that brannerite was the main reason for the existence of a dissolution limit in Witwatersrand ore and that chemical liberation was more effective to increase end dissolution compared to physical liberation. The findings from these investigations will form guidelines for developing economically viable flow sheets for improved uranium recovery, at least in a South African (Witwatersrand) context.

Jan 1, 2014

By H. Ding

Calcium carbonate/Titanium dioxide composite, characterized by coating TiO2 on the surface of CaCO3 particles, is an important substitute for titanium dioxide. This paper studies preparation method of CaCO3/TiO2 ,composites based on mechano-chemical effects, measures its properties as a pigment, analyzes the binding form and interface reaction mechanism between CaCO3 and TiO2. Through single finely grinding of CaCO3, co-grinding of CaCO3 together with TiO2, and mecha-no-chemical effects produced in the course of grinding, CaCO3/TiO2 composites can be prepared successfully. Results indicate that grinding fineness of CaCO3, co-grinding time of CaCO3 and TiO2, the weight ratio of grinding media to mineral feeding, and the amount of TiO2 have much influence on the properties of CaCO3/TiO2 composites. CaCO3/TiO2 composites have the properties same as titanium dioxide pigment, oil adsorption and ultraviolet adsorption same as TiO2, and 90% of hiding power as that of TiO2. Wet grinding of CaCO3 causes the production of mechano-chemical effect and hydroxyl group, through which CaCO3 and TiO2 can be bonded together. Repulsion occurs between the particles of CaCO3 and the particles of TiO2, respectively, they are both in good dispersion. But attraction occurs between CaCO3 and TiO2. TiO2 particles are distributed evenly on the surface of CaCO3. Therefore, coating of TiO2 on the surface of CaCO3 particles and chemical bond between them make CaCO3/TiO2 compo-sites have pigment properties of Titanium.

Jan 1, 2014

Considerable attention has been, and is being, given to the physics of water-films associated with bubble interactions at surfaces. In contrast, little information on the chemistry of such films has been reported. This communication reports a method using sum frequency vibrational spectroscopy (SFVS) to describe hydrogen bonding of interfacial water molecules in water films created with bubbles at hydrophilic and hydrophobic surfaces. The SFVS spectra of water films at hydrophilic silica surfaces differ significantly from the spectra of water at a hydrophobic silica surface. The SFVS spectra indicate that a very ordered water structure exists in water films at the hydrophilic silica surface during contact with a bubble and that the extent of hydrogen bonding increases with an increase in contact pressure. Such structural considerations as well as repulsive electrostatic and Van der Waals forces account for film stability for a bubble at the hydrophilic silica surface. In contrast, the SFVS spectra of water at a hydrophobic silica surface show a lack of hydrogen bonding and are characterized by a distinct absorption at about 3700 cm-1 similar to the spectrum of the air/water interface. These results suggest the presence of a water void, or water exclusion zone, at the hydrophobic surface, as supported by X-ray reflectivity measurements reported in the literature, by atomic force microscopy, and by the results from molecular dynamics simulations. Of course the water film at the hydrophobic surface is unstable with film thinning and rupture upon bubble contact. Under these circumstances it is shown that an attractive Van der Waals force between the bubble and the hydrophobic surface can be expected when the water exclusion zone is taken into consideration. As the thickness of the water exclusion zone increases to a thickness corresponding to the size of nano bubbles, the calculated attractive Van der Waals force increases. This analysis may help to explain the so-called ?short range? and ?long range? hydrophobic forces. Keywords: SFVS spectra, hydrophilic silica surface, hydrophobic silica surface

Sep 1, 2012

By David G. Hulbert, Daniël J. Oosthuizen, Bernard Muller, Daniël de V. van der Spuy

"Expert Online is a software system that makes use of novel artificial intelligence technology, known as the Interpreting Expert System (IES), to mimic an informed expert on a minerals processing plant. Previous implementations of the IES were only capable of explaining the controller actions. Expert Online will also take on the more difficult task of explaining the complex process behaviour to the operator in simple language.The primary functions of Expert Online are to serve as a training tool and an online assistant to operators. However, it is also expected to be of value to supervisors and plant managers.A number of additional features are envisaged, including different operating modes, fault detection, speech synthesis and advanced message filtering. Expert Online will increase the operator’s knowledge of the process and his/her understanding and acceptance of the complex control systems. Users would be supplied with relevant and timeous information required to make informed decisions to ensure smooth plant operation.This paper discusses the structural design of Expert Online for implementation on the latest version of MINTEK’s open control platform, PlantStar, as well as several advances and additions since the previous implementations of the Interpreting Expert System."

Jan 1, 2003