Search Documents

By Tom Treleaven

The success of any blast is dependent on the accuracy of the blast design and the field controls used on the shot. This point cannot be over emphasized because when the geometry is not measured and/or field controls are not properly implemented, it can often have devastating effects on the final blast results. Thus drilling accuracy, tiont row burden control, explosive confinement, energy distribution, explosive selection, timing and structural geology become critical parameters in the design of successful blasts. Understanding the actual dynamics of the blast and why certain results were achieved is the fast step in optimizing a blast design. As stated by R. Frank Chiappetta, “Of all the blast monitoring systems available today, high speed videography still remains as the best stand alone instrumentation system for blast diagnostics.” Over the past years I have analyzed hundreds of blasts using either high-speed lowcams (500 frames per second) cameras or standard digital (30 frames per second). These analyses confirm, without a doubt, that shot geometry, in combination with structural geology, is the most important factor in overall blast results. Drilling accuracy is the single most important component in efficient blasting. Having equal mass associated with an equivalent energy is the basis in which blasts are designed. When drilling inaccuracy or borehole deviation occurs, not only is the energy unevenly distributed, but the basis of all design calculations becomes invalid. Over the past several years, quarry and mining operations have employed the use of boretracking measuring devices to measure borehole deviation and hole toe locations. In cases of operations using top hammer drills, it was discovered that the amount of deviation was significant and far greater than they believed they had. Set up error, improper drilling techniques and bit wear were some of the contributing factors. Through video anaysis of boretracked blasts, blast results were directly linked to drilling ..accuracy. The comparisons here took into account blast design, energy factors and hole sequencing.

Jan 1, 2000

By Robert Hopler

A blast caused the destruction of a bridge and loaded freight train and the death of three men, near Chattanooga, Tenn., on May 16, 1907. The blast and its disastrous effect has been described by Mr. Hunter McDonald, M. Am. Soc. C. E., in a paper read before the Engineering Association of the South and reprinted in the Proceedings of the Association for April-June, 1907. The excessive damage was so largely due to coincidence and wreckage of the bridge and train so complete that the incident is worthy of notice.

Jan 1, 2008

By Dave Kay, Young-Suk Song

To meet the needs of South Korea's rapidly expanding economy, a large number of infrastructure projects are under way to improve transportation efficiency within the nation. These projects include high-speed rail links between major population centres and improvements to the road network. Being densely populated and geographically mountainous, infrastructure development in Korea requires a significant amount of tunnelling. Owing to the predominantly hard granitic nature of rock, drill and blast is the preferred method of tunnel advance. The Korean tunneller, however, faces the same pressures as those of his international counterpart in that both cost and production targets need to be achieved while meeting expectations of both community and regulator.

Jan 1, 2005

By Sri Sawmliana, P. Pal Roy

Blasting Gallery (BG) method was introduced in India for higher production and low cost of excavation to substitute conventional hand section and stowing methods for thick coal seam. The Singareni Collieries Company Ltd. (SCCL) adopted this method in the year 1989 and since then successfully operating at GDK-10, GDK-8 & VK-7 Incline mines in Andra Pradesh, a southern state of India. It is also successful at Chora 10 Pit Colliery of Eastern Coalfields Ltd. (ECL) in West Bengal whereas at East Katras Colliery of Bharat Coking Coal Ltd. (BCCL) in Jharkhand State, the method has been partially successful due to some geological constraints of the area.

Jan 1, 2003

By Larry Mirabelli, David Lilly

In 1777, the French naturalist, Georges Louis Leclerc, Compte de Buffon developed a statistical technique to estimate the width between two parallel lines by randomly throwing a needle at the two lines and counting the number of times the needle intersected one of the two lines. By knowing the length of the needle, the distance between the parallel lines could be estimated. This analysis was named the “Buffon’s Needle Problem”.

Jan 1, 2008

By Maurice Hunter

The paper outlines recent design developments in the computerization of surface crawler drills for the quarry industry. It references the technology firstly developed for the underground mining and construction industry, where automation and computerization has been in demand for a number of years.

Jan 1, 2003

By Francisco Sena Leite, Pedro Brito, Auã Kiahla, Raquel Carvalhinha, Tomi Kouvonen, Vinicius Miranda

Shockwaves that generate vibration in the surrounding environment of a blast, are one of the most important factors to control drill & blasting works near delicate buildings as well as in sensitive structures (wall control). On top of the damage to the buildings themselves, sensitive equipment such as computers, measurement apparatus and medical devices can be also compromised. The most commonly measured values from vibration are PPV (peak particle velocity), acceleration and displacement. Some devices and techniques have been developed in the last decades to measure the impacts of these vibratory phenomena. This information can be used to predict levels of vibration for future blasts and improve their quality of design using the attenuation law. From traditional studies to modern seismographs, a range of solutions are used for this propose. The main problem of applying this kind of technology is the high cost associated with each measurement device. In order to measure the ground vibration using new technologies while lowering the cost, a device has been developed using a microcontroller and electronic sensors commonly found on the market. This new equipment was tested side by side with traditional seismographs and the results were sent to a server for analysis. After several blasts, the necessary data was generated for the validation of the prototype. Through numerical mathematical processing (Taylor’s approach and numerical derivation) the original data supplied by the accelerometer’s sensors was transformed into velocity and, after the data mining, a statistics residue analysis was applied in order to evaluate if the data from the prototype and from the traditional seismographs were similar. The data from each system was used to estimate the attenuation law and the results are shown in this paper.

By Alastair Torrance, Mitchell Nipperess, Andrew Olsson, Italo Onederra, Gary Cavanough

Components of bulk explosive products include ammonium nitrate, water, fuel, stabilizers, and calcium nitrate. The physical attributes include prill/emulsion ratio, density, and viscosity and in the case of prilled ammonium nitrate, hardness, size distribution and fuel oil absorption. These components and attributes in conjunction with ground conditions determine all aspects of explosive performance including the risk of fume. This paper presents a fume risk assessment matrix of explosives components and physical attributes as a function of a simple description of ground conditions. Instrumentation to provide a measure of the quality of the explosive product are also described and these include both “on bench” physical measurements and laboratory analysis. “On bench” methods include “in hole “density, velocity of detonation (VOD), detonation pressure and detonation temperature. Part of the quality control process involves a mobile laboratory unit which at this stage can provide measurements of water content, ammonium nitrate content, calcium nitrate content, fuel content, prill characteristics and prill/emulsion ratio. This unit can be taken to sites to enable the testing of bulk and sensitized products at site rather than after transportation.

Jan 1, 2015

By Rob Domotor

This paper tells the story of using controlled surface and underground blasting methods to excavate hard rock in three areas on Australia’s largest road infrastructure project; the Airportlink Project in Brisbane; worth a total value of AUD $4.8 billion. The project used blasting methods including design, modelling, drilling and loading of the explosives that had never been used before in Australia, some of these were probably unique in the world.

Jan 1, 2012

By Francisco Sena Leite, Pedro Brito, Gean Frank, PhD Soeiro de Carvalho, Jose, Vinicius Miranda

The consequences of rock blasting with explosives are directly related to the accuracy of drilling and, because they have an effect on fragmentation and ground level, they should be controlled to ensure a problem free production, increase work safety and reduce environment impact. Safety control is one of the most important processes in detonation, since it can compromise the worker security on site and, eventually, neighboring communities. Due to the technology advancements, it is possible to build a hole deviation control device with “of the shelf” parts, and for that reason the authors decided to evaluate the possibility of measuring hole deviation by creating a portable prototype using an electronic sensor capable of measuring the acceleration on objects, that is, to measure the own acceleration of a system, known as "accelerometer" and a micro-controller to handle and treat data. The main idea behind this paper is to validate the power of the Euler method, given the stepping limitations of the sensor and micro controller in order to reproduce of the hole shape. A case study was carried out, comparing the measurements of borehole deviations made by a traditional equipment and the prototype. A mobile application was also created in order to recover and treat and display the data to the user. For validation of the prototype, several holes were measured using the two devices. A residue analysis was used to validate the data obtained. After analyzing and confirming the effectiveness of the new equipment, the normality tests prove a symmetric distribution with null expected residual mean and minimum variance. Consequently, the accuracy of the prototype is evidenced. Thus, the authors aspire to emphasize the potential of using these sensors allied to a traditional numerical method for analysis of hole deviation.

Jan 1, 2019

By Robert McClure, Frederic Leclercq, Ricardo Chavez

With significant vibration control and fragmentation challenges facing them, the CBS quarry (department of the Nord) successfully integrated a technical partner and mine to mill optimisation to deal with a difficult environment. For the last three years, CBS has been conducting a global production monitoring program similar to the mine to mill concept used in the mining industry. This concept consists of optimising the drilling and blasting while monitoring the effects on the downstream chain (vibration control, loading, hauling, crushing, plant output). Blast optimization is ensured by systematic control of the blast geometry (volumes, patterns, bench and face anomalies, drill deviation) and by the use of constant specific energy blasting. Constant specific energy optimises the work of the explosive in a blasting operation and, when combined with a high accuracy programmable electronic blasting system, reduces the impact of blasting on the environment and enhances blast performance. These techniques ensure consistent blasting results and hence improved site productivity. The improvements achieved have been identified thanks to an effective system designed to monitor the key production parameters.

Jan 1, 2007

By Richard E. Danell

"There are a variety of approaches for wall control blasting in open pit mining operations. Safety forworking in the pit is the principal benefit. There are also a number of economic and productivitybenefits when appropriate techniques are used. The purpose and requirements of wall control blasting can vary quite significantly for different operations. When considering blast design, geology, geotechnical factors, drilling, explosives, economics and blasting history are all part of the engineering design process. In many operations, there is a high reliance on blasting history and economics for determining wall control blasting measures. This presentation outlines approaches that broaden the design process and discusses their advantages."

Jan 1, 1997

By Brad H. A Brown, J Paul Tidman

To design a blast, one must give consideration to safety, economics, geometry, geology, production needs, and a variety of other requirements. To compare designs requires the time to develop alternatives, analyze, and then improve on them. A number of tools are available to assist with the first set of requirements, however they are poorly integrated. SHOTPlus is a program to improve the efficiency of blasting operations, by combining measurement and blast design tools, and offers the user the time and means to modify designs and explore alternatives.

Jan 1, 1997

By R. Frank Chiappetta

A new blasting technique has been developed by International Technologies, LLC. to eliminate subgrade drilling, lower ground vibrations, improve fragmentation and reduce explosive consumption. The new technique utilizes a uniquely designed borehole plug, with a bottom hole air deck and a predetermined stemming mass on top of the plug. This combination is referred to as the Power Deck?. Single holes and full scale tests were conducted by Blasting Analysis International, Inc. (BAI) to determine how the system works, the mechanisms behind its success and the best design parameters to use for the given rock conditions. Results have shown reduced or eliminated subgrade drilling, ground vibration reductions of up to 33%, reduced explosive consumption by 16 to 25%, and improved fragmentation by up to 25%. This paper summarizes the methodology, field test setups, analyzes procedures and results for one series of single hole and full-scale tests which were performed in a Pennsylvania, USA quarry.

Jan 1, 2004

By Pat McLaughlin

Environmental constraints are pushing many operators to change from large rotary blastholes to the smaller diameter holes drilled with down-hole or top-hammer rigs. Productivity improvements over the years with these two drilling techniques has taken some of the bite out of the transition, while improved fragmentation and more uniform muck due to the tighter patterns can help offset increased explosives costs.

Jan 1, 1995

By John Vynne

Too often, a mine’s operations, including drilling, blasting, loading, hauling, crushing, processing, etc., are considered independent steps, rather then a continuous process. In fact, these are interdependent operations with each step in the process having an impact on subsequent operations. If the effectiveness of the drilling and blasting operations can be improved, they will impact the entire mining process. Some of the resulting improvements include: level benches on grade; fragmentation and diggability with the result being reduced loading times; haul cycles improvements; and the crushing and milling operations will be more efficient and less energy consumed. Thunderbird refers to this as “Drill to Mill” information cycle or process. This paper focuses on two of the technological enhancements Thunderbird has added to its drill monitors that allow the mines to impact the “Drill to Mill” concept. These enhancements are: incorporating global positioning satellites into drill monitors; and radio off-loading of data. Thunderbird is part of the Integrated Mining Systems (IMS) alliance. IMS offers the mining industry the most comprehensive line of monitoring and navigation products available today for mobile mine equipment. In addition to Thunderbird’s drill monitors and GPS systems, the product line includes: Fleet Management Systems for trucks and loaders; dragline and shovel monitors; GPS based navigation systems for shovels, dozers and other mobile equipment; and surveying systems. IMS uses common communication systems, operating systems, and hardware components in order to provide a truly Integrated Mining System.

Jan 1, 2000

By Patricio Santis, Jacopo Seccatore

Artisanal and Small-scale Mining (ASM) is a prominent activity in the extractive industry: considering only gold, it produces about 20% of world market supply. Despite this fact, ASM is generally associated with negative aspects of its environmental impact, and operational research is generally neglected. This paper emphasizes the peculiarity of the drilling and blasting systems of small underground mines in selected South American Countries. Such Countries, while having large mineral deposits and well recognized large-scale mining activities, at the same time still present on their territory ASM activities that are archaic, highly inefficient and dangerous for the safety of its operators. This paper documents drilling and blasting activities from gold mining in Ecuador and Chile. First, are described the outdated and often non-rational techniques employed by miners, to provide a general framework of the current methods. Then, it is shown what can be improved and how the current methods can be modified. Finally, are shown some field applications and the comparisons of the results obtained. One case shows how blast pull efficiency can be increased of from 82% to 98% by changing non-rational applications of explosive products. Another case shows how, by rationalizing blast designs, drilling and blasting costs can be reduced by 9% per month, the advance by blasting increased by 29% and the blasting efficiency increased from 70% to 90%. Finally, it is concluded that examples of application show how operational improvements are easily applicable on the field, relying only on tools and resources of artisanal mining, but combining solid engineering bases with confidence-gain and respect for the experience of the miners.

Numerical modelling was used to examine priming of bulk commercial explosives. Data for the HOM equation of state were calculated using a representative chemical composition, while Forest Fire model data were calculated, using a Pop plot which was estimated on the basis of existing sensitivity data, albeit for cap sensitive, small diameter explosives. The length and diameter of the primer, the location of the detonator in the primer and the shape of the primer form a set of parameters which are investigated. The effect of confinement and borehole diameter are also demonstrated, as reflections of shock waves create regions of high pressure in the explosive. The results are presented in terms of pressure and decomposition histories in the explosive and are interpreted in an engineering fashion to form rational suggestions for optimization of the priming process in the field.

Jan 1, 2002

By Braden T. Lusk, Shannon P. Lusk, Kyle A. Perry

A high explosives shock tube has been constructed and developed to test blast resistant windows with pressure versus time waveforms similar to waveforms generated by arena testing. Calibration of the high explosives shock tube, or Large Arena Test Simulator (LATS), included numerous tests performed by detonating varying charge weights at different distances from three piezoelectric pressure sensors located at one end of the shock tube (where the test subject would be installed). The maximum reflected pressure and positive phase impulse were calculated for each waveform generated in the tests. Pressure versus distance and impulse versus distance graphs were generated. Results have been graphed in order to predict charge weights and distances that correlate to the desired pressure and impulse at the end of the tube for future tests. This is a valuable tool when testing expensive, job specific components so the loading requirements are met on the first attempt.

Jan 1, 2010

By Ruilin Yang

Blast vibration in the highwall from a cast blast in open pit mines or in the hanging walls from a stope blast in underground mines is a common concern. Vibration in such cases is a typical near-field situation where the distance from a blasthole to a point of interest varies significantly compared to the distance between the blast as a whole and the point of interest. Most existing blast vibration models are designed for far-field vibration using a single seed wave to represent all blastholes within a blast and do not simulate wave shape change over the distance. Using the site parameters from the analysis of signature hole vibrations, the present blast vibration model yields reasonable agreement with field measurements in terms of vibration amplitude and frequency. Case studies show that the model has been used successfully to assist field vibration control.

Jan 1, 2010