Search Documents

By Isaac E. "Chip" Harris

Any contractor who agrees to supply materials or to perform services for a sum, is well aware of the importance of proper pre-bid information. Being able to properly plan costs and methods results in profits that allow the contractor to prosper. The paper discusses procedures used in estimating pre-bid cost; in particular, drilling and blasting cost for highways, dams and general construction projects. It breaks cost down into five categories and relates them to a total estimate used in bidding and budgeting a construction project.

Jan 1, 1975

By D K. Joyce, B Mohanty

In a previous paper, it was shown that a lack of clear understanding of the role of initiation mode on detonation characteristics often leads to under-utilization of the explosive system in blasting. This is of particular significance since the very large number of explosive initiation practices currently in use implicitly assumes that the blasting performance of an explosive is largely independent of the exact mode of initiation. This paper deals specifically with bulk-loaded and pneumatically-loaded ANFO under various initiation modes in small diameters. These include initiation by booster and detonating cords of various strengths, and combination of cords and boosters. The nature of energy release and energy partitioning between shock and gas energy have been studied in the underwater test as a function of charge diameter. The paper describes the relative merits of various initiation modes for specific charge geometries and confinement, under end- and side-initiated conditions. Guidelines have also been formulated for use in the field to match initiation practice with blasting requirements.

Jan 1, 1994

There is an intuitive tendency to equate rock strength with rock stability, yet the two must be evaluated separately. A slope in strong hard rock is not necessarily stable, nor is a slope in weathered weak rock necessarily unstable. In some cases the reverse is true, depending on the geometry of joints and weak planes. The time element is a matter of special concern, that is how suddenly the failure begins and how rapidly it progresses. Sudden failures can be catastrophic, whereas creep usually is not. In soils and weathered rock, the process is usually incremental and is more likely to give some warning of impending failure. With careful observation, the failure process in these materials can be detected and monitored instrumentally or visually. In some cases, the slope may be stabilized, reinforced or modified. When that is not possible, there is usually enough time on this type of slope to remove men and equipment from the area before complete failure occurs.

Jan 1, 1996

By Stephen John Brace

Increasingly, electronic blast initiation systems are being made available to the mining and construction community, both in South Africa and internationally. Indeed, in some parts of the world, perhaps half a dozen electronic products are being used, with a choice also of shock tube, electric and fuse and igniter cord systems. As these developments have taken place, improvements have been made in safety, reliability and accuracy, so much so that high performances in all these areas are now expected. However, disadvantages often seen by customers, other than : higher price, are decreased user-friendliness and loss of flexibility.

Jan 1, 1998

By Daniel Roy, Chris J. Preston, Ron J. Elliott

This paper discusses the use of pressure transducers in water filled boreholes in conjunction with surface mounted geophones to gather field data for in-situ dynamic rock properties determinations. A high speed collector is used to capture the data in the field. The calculated P and S wave velocities and rock density measurements are used as input into the Blastcalc program where the values of Young`s Modulus and Poissons Ratio are calculated. The rock properties information is used along with geological structural data and explosives properties in a 3-D blast modelling program to calculate predicted fragmentation distribution and other blast performance criteria based on the proposed blast design.

Jan 1, 1996

By Robert L. Martin, Brian W. Stump, David P. Anderson, David Gross

In an attempt to better understand the impact that large mining shots will have on verifying compliance with the international, worldwide, Comprehensive Test Ban Treaty (CTBT, no nuclear explosion tests), a series of seismic and videographic experiments has been conducted during the past two years at the Black Thunder Coal Mine. Personnel from the mine and Los Alamos National Laboratory have cooperated closely to design and perform experiments to produce results with mutual benefit to both organizations. This paper will summarize our activities, highlighting the unique results of each.

Jan 1, 1997

By Dieter Froelich, Giles Turcotte

In the near future, Bong Mining Company (BMC) will start mining a new deposit known as Zaweah II which is a narrow iron orebody requiring multiple row blasts with the bench floor as a free face. This called for the development of a new blasting technique. The article delineates the problem and its restrictions related to blasting. It also describes the approach which was taken for developing this new blasting technique which is essentially an application of the cratering theory with near spherical charges. Basic crater tests were conducted using various combinations of hole sizes, explosive strengths and delay patterns. From the results obtained, several alternatives were considered for production blasts and the most promising ones were evaluated.

Jan 1, 1980

By Kevin Cole, Dennis A. Clark, F William Laslow

Since 1976, the Metropolitan Sanitary District of Greater Chicago, (MSDGC), has commissioned the excavation of a tunnel system in the Chicago area, hundreds of feet below the surface in solid limestone. This paper outlines the blasting patterns, explosive selections, and monitoring techniques used to assure a satisfactory job completion, following the specifications.

Jan 1, 1982

By Jesus Pascual, Jose Sanchidrian, Pablo Segarra

The surface vibration field in the area above an underground mine prior to its development has been investigated, in order to assess the vibration levels expected in existing buildings and in the planned mine facilities from future underground blasts. Shots of 50 and 100 kg of explosive placed in drillholes at depths of 100 to 150 m were fired, and the vibration events were recorded using an array of 40 seismographs in a 400 m square grid, covering a 2×2 km area. Contours of isovelocity were obtained for each shot, showing some directional transmission patterns. Propagation laws were obtained from the results of each shot and also from the bulk of data, both for the whole area and dividing it into four quadrants. The shift of dominant frequency with distance was also analyzed.

Jan 1, 2002

By John Kemeny

There are many methods used to predict blast fragmentation, including empirical and numerical models, field trials, and experience from ongoing blasting. All of these methods require an accurate measurement or prediction of the rock mass properties. These properties include the characteristics of the rock fractures, including fracture density, friction angle, orientation, length, roughness, fill, etc. They also include the hardness of the intact rock, water content, and other parameters. This paper describes three new technologies that can be used to automatically or semi-automatically obtain rock mass properties: digital image processing, 3D laserscanners, and drill monitoring systems. Each of these technologies is described, including the current state of the art, current limitations, and their future potential. Each of these three technologies has advantages and disadvantages. These new technologies, however, have the potential for providing accurate rock mass information in an automated and real time fashion. This information can then form the basis for a new generation of real-time, database driven blast fragmentation models.

Jan 1, 2004

By Lawrence W. Hallanger

Anaheim Bay, located at Seal Beach, California, is the site of the Huntington Harbor development of waterfront homes and marine facilities. The main entrance to Anaheim Bay is a relatively narrow channel connecting the bay with the Pacific Ocean which runs under California State Highway One. During the development of Huntington Harbor the old highway bridge was replaced with a new, higher bridge to allow for boat passage through the channel. At that time only the main span decking of the old bridge was removed, leaving the support pillars and the approach ramps in place (see Figure 1). The narrowness of this channel, plus the increasing boat traffic created a situation in which public demand for the removal of the old bridge became significant. Because the bridge was located within the boundaries of the Seal Beach Naval Weapons Station (see Figure 2) the Navy became involved in the bridge removal. Eventually the task was assigned to the Naval Amphibious Construction Battalion One and work began in early 1974.

Jan 1, 1975

By Michael A. Peltier, Dennis V. D'Andreal, Larry R. Fletcher

Accident data obtained from the Mine Safety and Health Administration (MSHA) were analyzed by the Bureau of Mines to determine the most frequent causes of blasting accidents in U.S. mining and to examine trends in blasting accidents. This accident analysis is an update of a similar blasting accident study conducted by the Bureau and published in 1983. The analysis shows that there has been a recent reduction in mine blasting accidents: The annual average number of nonfatal injuries has decreased from 107 for 1978-81 to 46 for 1982-85. The annual average number of fatal injuries was reduced from 11.3 to 5.0 during that time.

Jan 1, 1987

By Alan Tordoir, Mark Roberts

The drill and blast process is a critical function within the production cycle which significantly impacts the ability of an operation to effectively meet its safety and production targets. Acknowledging that D&B design and reconciliation practices were conducted inconsistently across operations, a Group wide initiative was launched to embed a standardized design and reconciliation platform in line with the company’s Operating Model principles. A technical system was selected to deliver the digitalization of critical D&B information and enable ‘analyze and improve’ routines for design compliance monitoring and downstream productivity optimization.

Jan 1, 2019

By L. L. Oriard

he Metropolitan Water District of Southern California (MWD) supplies water to some 16 million people in a semi-arid region. Most of this water is imported. Some of the supply lines cross over the San Andreas fault, one of the most notorious and active faults in the U.S. There was a serious need for emergency water in case normal supplies should be interrupted. To fill that need, MWD had to find a reservoir site on the west side of the San Andreas fault, west of the mountains. Because of the distinctive nature of the location, it was necessary to construct a huge “bath tub” by building a dam at each end of a valley, requiring some 115 million cubic yards (88 million cu.m) of fill. In effect, two large-scale surface mining operations have been under way simultaneously. The $2.2 billion project is known as the Eastside Reservoir Project. Because of space limitations, this paper will be limited to those topics which are expected to be of primary interest to explosives engineers, principally related to large-scale rock fill production. There is not sufficient space to discuss the many diverse geotechnical questions related to site selection, geological and geophysical field testing, laboratory testing and design considerations. This brief overview may assist those who might be interested in making a tour of the project site following the ISEE conference.

Jan 1, 2000

By Richard J. Mainiero, Harry C. Verakis, John J. Mulhern

There are application in coal mines where it would be advantageous from a safety stand point to fire unconfined shots. However, the firing of mud caps (adobes) or other unconfined explosive charges in underground coal mines is not permitted because of the explosion hazards associated with methane gas and coal dust. Present safety regulations in Title 30, Code of Federal Regulations prohibit such Practices. Recently, MSHA proposed revised coal mine regulations for the approval and use of sheathed explosives for Public comment.

Jan 1, 1987

By Dale Ross, Bill Clements, Jim Spanos

Current world conditions are forcing the search for "green" energy technology in every aspect of our daily lives. Finding alternatives to petroleum fuels seems to be at the top of the list. The search for the "perfect" alternative is something like the never ending quest of the perpetual motion machine. Unfortunately, the laws of physics prevent us from getting something for nothing, and Murphy's Law normally gives us nothing for a lot of something. Regardless of Murphy, the quest goes on, and in our industry cheaper ANFO seems to be the popular subject.

Jan 1, 2012

By W. Jiao, Y. Yongqi, R. Shan

Soft rock mines are distributed through out P.R.C. And drilling and blasting is still the main method of driving a tunnel in these mines. Traditional smooth blasting has been widely and deeply studied and put into practice in P.C.R since 1970s. But the cartridge and blast hole are both columns, the stress field in the rock around blast hole at the beginning is symmetry around hole axis, and the original cracks in the rock can be activated randomly. So serious overbreak and underbreak at the boundary of an excavation occur often, especially when the excavation is in soft rockmass, and the rates of half-hole marks are generally about 50% in medium rock, and 20-30% in soft rock in Chinese coal mines. For the sake of overcoming the situation, we have been studying directed crack blasting since ten years, and have got some obvious achievements in this respect. Slotted cartridge control blasting in soft rock is studied in this paper. Through model experiments, reasonable decouple coefficient range and slot width are gotten, and unsymmetrical dynamic strain field is analyzed. Through underground test in soft rock with a strength lower than 1OMpa in Dayan Mining Bureau, The results of which the rates of half-hole marks and the nonsmooth grades of the cut contours are 83.3% and 1OOmm respectively have been achieved.

Jan 1, 2000

By Lex L. Udy

External detonation generated plasmas, highly ionized zones of reacting material ejected from the surface of detonating explosive charges, are shown to be the cause of channel desensitization, i.e., the self-quenching of a detonating explosive column loaded in a borehole with an air annulus between the explosive and the borehole wall.

Jan 1, 1977

By Ruilin Yang

Techniques for the study of blast vibrations, such as monitoring, analysis, and modeling are often misused between near field and far field blast vibrations. This paper discusses the differences between near-field and far-field blast vibrations in terms of these techniques. A typical example of a near-field blast vibration problem is a blast vibration in the crest of a new highwall behind a cast blast. In such a case, the blast can be a couple of hundred feet long and the distance from the blast holes to a monitoring station may only be 100 feet or less. In this situation, the size or spatial geometry of the blast is not negligible compared to the distance from the blast to the vibration monitoring point. On the other hand, a typical example of a far-field blast vibration problem can be a quarry blast with a nearby residence house. In this case, the distance from the blast to the house may be several thousand feet. The size of the blast is less than a couple hundred feet long and negligible compared to the distance from the blast to the vibration monitoring point.

Jan 1, 2007

By Ulrich Leiste, Andrew Wardlaw, William Fourney

This paper describes the loading on a plate suspended directly over an explosive charge submerged in water. This problem is of interest because it yields results similar to those obtained in the detonation of an explosive buried in saturated soil and thus it is associated with landmines. Recent experiments [1] indicate that plate loading from a submerged charge is similar to that for a buried one, with respect to impulse and pressure. Compared to the buried explosive problem, the submerged explosive case is attractive from a computational point of view; it replaces sand, which is diffi cult to simulate, with water, whose properties are well known. Studying this problem allows modeling uncertainties to be separated from sand simulation issues.

Jan 1, 2008