Search Documents

By Ernest J. Conway

This report presents engineering drawings for six material handling devices for underground coal mines. The devices were designed under a U.S. Bureau of Mines program to reduce injuries from material handling during mine and equipment maintenance. The six devices are (1) scoop-mounted 1411: boom, (2) swing-arm boom, (3) heavy-component lift-transport, (4) mine mud cart, (5) container-workstation vehicle, and (6) timber car. Each device is described briefly, and recommendations are made concerning the design of new devices.

Jan 1, 1989

The contract for the Water Jet Chock Mounted Miner Feasibility Study was awarded to FMC Corporation's Advanced Products Division on 18 November, 1974. The program was divided into four phases as follows: ? Phase I - Planning ? Phase II - Conceptual Design ? Phase III - Budgetary Cost Estimate and Economic Feasibility Study ? Phase IV - Final Report During Phase I, which lasted 1 month, most of the necessary information and data for the conduct of Phase II was obtained. To accomplish this, arrangements were made for personal visits to the University of Missouri at Rolla, Illinois Institute of Technology Research Institute, USBM TCMRC, Alpine Equipment Co., Mining Progress, Inc. and Eastern Associated Coal Corporation's Harris No. 1 Mine. Also, a list of manufacturers of high pressure equipment was compiled to be contacted during Phase II. Finally, the objectives to be accomplished during Phase II were outlined. The Phase I Report was submitted on 23 December, 1974. At the beginning of Phase II, personal visits were made to the research centers and firms mentioned above. Later an additional visit was made to the Harris Mine, and to the Pittsburgh Mining Research Center at Brucetun to observe a test of a water jet mounted on an Alpine Mining Machine. Equipment manufacturers of high pressure components such as hoses, tubing, valves, pumps, and intensifiers were contacted to obtain item performance data, availability, and cost.

Jan 1, 1975

"INTRODUCTION Industrial utilization of the present submarginal domestic manganese resources of the United States is wholely dependent at this time on the electrolytic manganese process established as the result of 4 years of continuous operation of the Bureau of Mines pilot plant at Boulder City and 7 years' operations of the Electro Manganese Corporation commercial plant at Knoxville, Tenn.Three Kids ore provided the feed for the Boulder City pilot plant during 3 years of operation. Hence, the electrowinning characteristics of the ore have been thoroughly established, making possible accurate estimates for commercial operations.Before the Defense Plant Corporation constructed the leaching plant, the Bureau of Mines conducted an exploration project to determine the extent and grade of the ore reserves. Additional exploration, development, and mining by the Manganese Ore Cc, have accurately determined the tonnage and grade of ore. A large tonnage of stock piled ore is now available for immediate processing, and a considerable tonnage of openpit ore has been stripped of overburden preparatory to mining. Numerous facilities, such as power, water, and housing, needed for an electrolytic manganese plant are already available.All of these factors, as well as plans for installation of scale electrolytic manganese plant facilities, are presented in detail in the chapter entitled, ""Mining and. Electrolytic Reduction of use from Three Kids Manganese Mine."" The Manganese Ore Co. kindly provided information on the present ore reserves and state of development of the mine."

Jun 1, 1945

By J. Dean Warner

From 1984 through 1987, the Bureau of Mines investigated numerous prospects and new discoveries of columbium, rare-earth elements (REE), uranium, zirconium, and other metals associated with the multi-phased peralkaline granite at Bokan Mountain, southeastern Alaska. This report summarizes the mineral evaluations and estimates indicated and inferred resources for those prospects containing significant tonnage and grade. A total of approximately 96.2 MM lb Cb205 (43 pct of the tonnage at a grade exceeding 0.125 pct Cb205), and 11.8 MM lb U308, 27.9 MM lb Th02, 133.0 MM lb Y203, 637.6 MM lb ZrO2, and 241 MM lb REO are estimated to be contained within nine deposits totalling 37.8 million tons (at least 80 pct of resource tonnage also exceeds 0.5 pct Y203 + REO). Generally, half of the REO content is composed of the heavy yttrium subgroup. Several deposits also contain beryllium and tantalum; 2.1 MM lb of Ta205 and 8.9 MM lbs of BeO were estimated. These estimates would likely be substantially increased with additional exploration. Four deposit types were investigated; shear zones and fracture-related deposits, pegmatites, mineralized dikes, and placers. Mineralized dikes contain most of the beryllium, columbium, tantalum, yttrium, zirconium, and REE resources, whereas shear zones and fracture-related deposits (Ross-Adams mine) contain the principal of the uranium resource. Pegmatites are similarly mineralized as are dike deposits, and contain low levels of gold. Placer potential is suggested, but no deposits were found.

Jan 1, 2011

By Michael M. Hamilton

In 1984 and 1985 the U.S. Bureau of Mines performed a mineral survey of the South Jackson Mountains Wilderness Study Area covering 60,211 acres of mountainous terrain of Humboldt County in northwestern Nevada. Approximately 550 lode claims have been located within or adjacent to the study area from 1900 to the present. Total recorded production for the area is 28.19 ounces gold, 1,105 ounces silver, 959 pounds copper, 6,016 pounds lead, and 12,446 pounds zinc; an additional two carloads from one mine contained an unknown amount of metal. In early 1986, there were eight active properties with a total of 126 claims. Wescord Resources and Long Lac Exploration (Texas) Inc. are involved in a joint exploration of the Jackson Mountains for volcanogenic massive sulfide deposits. Development at the Claudia mine continues in 1986. Results of the survey indicate that there are no identified mineral resources or reserves within or adjacent to the study area. Twenty-two properties have mineral occurrences containing gold, silver, copper, lead, zinc, iron, antimony, vanadium, and cobalt, with silver, copper, and iron being the most abundant.

Jan 1, 1987

By Anderson Dana

THIS PAPER describing methods and costs of mining and preparing gravel and sand for market at the Port Jefferson plant of the Seaboard Sand and Gravel Corporation, is one of a series of articles on gravel and sand mining, prepared for and published by the U. S. Bureau of Mines, which is designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs, It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical [ ]

Jan 1, 1932

By Thomas Novak, Jeffrey L. Kohler, Joseph Sottile, Steve J. Gnapragasam

Modern underground coal mines can be very large, having a total connected load in excess of l5 000 hp. These mines generally have many miles of high-power conveyor belts and 15 or more miles of high-voltage power cables at distribution voltages of 12.47, 13.2, 13.8, or 14.4 kV. The shielded cables used in mine power distribution systems have a significant level of capacitance, on the order of 110 pF/ft. This level of capacitance, in an extensive power distribution system at today's voltage levels, can cause significant charging currents during a ground fault. This paper addresses the potential detrimental effects of capacitance charging currents during line-to-ground faults in mine power distribution systems. A representative mine power system is modeled, and simulations with faults at various locations are conducted to evaluate the effects of this capacitance on the level of fault current and relay selectivity. This paper also includes results of capacitance measurements made on mine power feeder cables used to validate the simulation model.

By G. L. Oldright

The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada, Ltd., Trail (Tadanac), British Columbia. Many thanks are due to S. G. Blaylock, vice president and general manager, James Buchanan, smelter superintendent, and George Murray, assistant smelter superintendent, for their broad general policy in permitting these data to be taken and published. life are also grateful for the help given by the staff members stated in Paper XI, Report of Investigations Acknowledgment is given several excerpts from experiments by F. E. Lee, head of the research staff. INTRODUCTION The past reputation of zinc as an ingredient in lead blast furnace slags has been bad. Zinc is thought of as a cause of accretions in the shaft of the blast furnace, of hot tops, of the formation of "zinc mush" in the crucible and forehearth, of lead-rich slags, of viscous slags, and. of low capacity in smelting.

Jan 1, 1934

By L. Bruce McDonald

This Federal Bureau of Mines publication is a statistical analysis of all surface and underground coal mine fires reported in the United States from 1950 to 1977. Accounts of selected nonreportable fires and opinion data gathered via interviews with mine safety directors were separately analyzed. Both reported and nonreportable fires were analyzed by time trends, State, ignition source, burning substance, location in mine, equipment, detection, duration, injuries, fatalities, and successful extinguishing agents. It was found that the majority of all mine fires were electrical in origin. The equipment most frequently involved in underground fires was conveyor belts, and in surface fires, it was crushers and/or breakers. Underground fires occurred most often near the working face. Water and hand-portable extinguishers were the most common methods of extinguishment.

Jan 1, 1980

By C. Daniel Kealy

Dissolved and suspended solids are present in the free water of tailings ponds. This Bureau of Mines study was designed to identify the influences of the slime zone in preventing these solids from reaching the environment outside the tailings pond. The finite-element method was used to determine the rate of discharge of subsurface water from the Van Stone tailings pond in northern Washington. The slime zone was sampled and tested for the first time, and results were interpreted and incorporated into the mathematical model. Computer results were verified by installing and monitoring piezometers in the field and by a simulated (16- by 1/2- by 3 foot) laboratory model. Output from the numerical model defined critical seepage zones and revealed that proper pond design and maintenance can reduce pond seepage losses to a minimum. Minimization of seepage requires maintaining the pond water level over the slime zone. Sufficient physical, chemical, and limnological data were collected and analyzed to conclude that the only realistic reflection of synergistic effects is obtained by study of the indigenous biota in combination with quantitative chemical and physical data. Proper planning and management of the milling and waste disposal operations are the key to minimal pollution.

Jan 1, 1974

By Frank S. Wartman

"The experimental flotation work described in this paper was undertaken to test the conclusions derived from a previous microscopic and chemical study of several samples of converter slag. That study3 resulted in the conclusion that approximately 90 per cent of the copper content of a converter slag wad in either the sulphide or metallic form, and that if the slag were cooled slowly the copper-bearing material would be in particles of such size that they would be freed from silicate and magnetite grains by grinding the slag to pass a 150-mesh sieve. If this were true, it should be possible to separate the copper-bearing grains from slowly cooled, converter slag by the flotation process.Many attempts, of which the author has seen no published account, have been made to treat slags, especially converter slags, by flotation. In every case these trials have been made with chilled slags, in which, as shown in the preceding report, the copper-bearing material is top finely disseminated, to be freed by any reasonable degree of grinding.The flotation tests described in this paper have shown that it is possible to recover by flotation about 30 per cent of the copper content of a converter slag containing 3 per cent copper and to obtain flotation concentrates which have a copper content of 35 per cent.Acknowledgment is made to G. L. Oldright, supervising engineer of the section of nonferrous metallurgy, U. S. Bureau of Mines, for valuable assistance and direction; to W. A. Sloan for chemical analyses; and to Alfred P. Towne for assistance in experimental manipulation."

Apr 1, 1931

By Frank E. Cash

As a part of its safety program the United States Bureau of Mines has fostered the development, use, and improvement of portable electric mine lamps. Although there is still need for better illumination in mines and the replacement of open lights has been slow, improvement in electric cap lamps and increase in their use indicate one phase of recent progress toward safer and more efficient mining This report is the result of a recent survey of electric-lamp installations in the Alabama mining; district; it shows the misuse, increase in use, and relation to certain classes of accidents of these installations.

Jan 1, 1935

By John P. Borovsky

A 3-year study was conducted to evaluate the problems and benefits of using vegetation to stabilize tailing from a potential Minnesota copper-nickel milling operation. The project consisted of three separate investigations: a waste characterization study, a greenhouse study and a field study. With few exceptions, the physical and chemical characteristics of the tai ling were found to lie within the range of properties of Minnesota soils. The tailing lacks organic matter; is deficient in nitrogen, phosphorus and potassium; and may contain elevated levels of soluble salts and heavy metals, particularly copper and nickel. Numerous grasses, forbs and woody plants will tolerate the tailing as a rooting medium. Peat incorporation and topsoil dressing provided few benefits to the revegetation process which were not provided by a fertilizer application. With fertilization, grass/legume production in the tailing was comparable to local agricultural yields. Concentration of heavy metals in grasses grown in the tailing were generally below suggested tolerance limits for plants and animal forage. Legumes tended to accumulate higher concentrations of copper and nickel, and metal uptake of most plants was positively correlated with rate of fertilization. Tailing drainage water contained elevated levels of heavy metals, and establishment of vegetation had little effect on the quantity and quality of tailing drainage water. However, topsoil dressing significantly increased drainage water volume when compared to unvegetated control plots. Copper-nickel tailing revegetation recommendations were developed.

Jan 1, 1983

By Richard A. Dick

Underground blasting in permanently frozen gravel was studied in a 7-by 12-ft drift by running a nonreplicated 2 X 2 X 2 factorial experiment on the effects of type of cut, delay, and explosive on the fragmentation subsystem. Comparisons were made between a V-cut round and a burn-cut round, millisecond delays and half-second delays, and 40 percent special gelatin and 60 percent high-density ammonia dynamite. The number of large blocks in the muck pile) loading time, shuttle car operating time lost because of cleanup needs, length of advance per round, and length of muck pile were recorded and statistically analyzed. None of the blast parameters had a significant effect on the length of advance or length of muck pile, although the half-second delays tended to give a shorter muck pile than millisecond delays. The burn cut required less secondary breakage, less loading and cleanup time, and gave better overall fragmentation than the V-cut. The ammonia dynamite shots required less secondary breakage and less loading time than those using special gelatin. The half-second delays gave better overall fragmentation and required less cleanup time, but the millisecond delays gave a better loading rate. None of the differences between delays and explosives were notably significant.

Jan 1, 1970

By Clarence Karr

THE BUREAU OF MINES is investigating methods for upgrading tar produced by the low-temperature carbonization of bituminous coal. This survey was undertaken to compile information needed for identifying the ether constituents of low-temperature tar. Physical properties are listed for 1,024 aromatic ethers. The compounds include cyclic and noncyclic, polyfunctional and monofunctional ethers with oxygen joined directly to either one or two aromatic rings. Alkyl groups up through butyl are included. The compounds are divided into 37 groups ranging in complexity from alkoxybenzenes to dibenzopyrans. Compounds containing aromatic ether groups are important constituents of the neutral oxygen components of low-temperature tar. For example, at Morgantown, W. Va., the Bureau of Mines has identified and determined the amounts of benzofuran, 2-, 3-, 5-, 6-, and 7 -methylbenzofuran, diphenyl ether, dibenzofuran, 2,3-dimethyldibenzofuran, and two other dimethyl-dibenzofurans in the neutral oil from a low-temperature bituminous coal tar (103, 104).3

Jan 1, 1962

By Mark I. Copeland

A study was conducted to determine if commonly used alloying additions or coating materials can prevent the formation of a liquid-copper phase during the reheating of copper-containing steels. If so, the tendency of such steels to surface-crack during hot-working might be eliminated. Steel specimens were scaled by heating them either isothermally or in a programed manner that simulated industrial furnace practice. Metallographic examination of the heated specimens showed that molten fayalite (Fe2Si04) completely prevented the formation of liquid copper at the surface. Fayalite, which melts at 2,200° F (1,205° C), was formed by internal oxidation of the silicon contained in the steel. By forming complex molten oxides, coatings of borax glass were also effective in preventing the occurrence of liquid copper at the steel surface.

Jan 1, 1972

By Ronald W. Stingelin

The geology of the roof of the Pittsburgh coal bed was studied and mapped in nine contiguous counties containing the bulk of the remaining reserves of this coal bed in the northern Appalachian Coal Basin. Drill core records from Belmont and Monroe counties, Ohio, Washington and Greene counties Pennsylvania, and Ohio, Marshall, Wetzel, Monongalia, and Marion counties, West Virginia provided the data for twelve computer generated regional geologic variable maps. Four of these geologic variables (overburden thickness, vertical distance to the rider coal, lithology at the five foot horizon above the roof of the mineable Pittsburgh seam, and the number of lithologic changes within the 30 foot interval above the roof of the mineable Pittsburgh seam) were used to estimate the risk of potential roof falls by a methological scheme developed during this study. A hazard zone risk map was developed showing a generalized regional trend of increasing risk from west to east across the basin. Mapping of individual geologic variables and mapping of hazard risk can be done at any scale. The accuracy of the mapping is primarily dependent on the density of the drill core records. Geologic feature maps and the hazard risk map contained in this report are reduced (1 :500,000 scale) versions of the larger scale (1 :62,500) maps prepared for the Bureau of Mines as map folios.

Jan 1, 1979

By Wils L. Cooley

This report analyzes electrical accident data in the metal/non-metal mining industry. Accidents are categorized to determine their root causes. Special attention is given to accidents associated with inadequate or defective grounding of mine power systems. Recommendations are made concerning proper grounding practice, especially for dredges and for quarries in hard rock or sand. The costs of instituting the recommended practices are estimated for model mine power systems which are based on field data obtained from 37 mines and several electrical contractors. The expected benefits of various suggested safety practices are also estimated.

Jan 1, 1981

By J. J. Lukasko

The U.S. Bureau of Mines developed an alternative electrochemical process for the production of calcium metal. The current industrial practice is costly, complex, and inefficient. The Bureau method involved electrowinning of a calcium-tin alloy followed by electrorefining to produce calcium metal. In the electrowinning cell, CaCI2 was fed to a KCI2-CaCI2 electrolyte. The calcium was electrowon at 6500 C into the pure molten tin cathode until the cathode contained 7.5 wt pct Ca. Current efficiency for electrowinning averaged over 90 pct. The resulting calcium-tin alloy served as the anode for the electrorefming cell, which employed a [CaC~-CaF2] fused salt as the electrolyte. Calcium metal was electrorefmed at 8500 C with a current efficiency of 85 pct based on calcium metal recovered. The calcium metal analyzed 99.2 pct, which is purer than commercially produced calcium.

Jan 1, 1990

By R. Pallini

The Franklin Research Center (FRO, a Division of The Franklin Institute was contracted by the U.S. Department of Energy to investigate the application of elastomeric materials for the purpose of smoothing loads on dragline thrust rollers. This report covers the design, fabrication, and demonstration of a portable- device for measuring roller circle track deviations and roller loadings. The results of this work are documented in this report. During December 1981, a field test group visited the Falkirk Mine, Underwood, North Dakota for the purpose of demonstrating the use of the designed and built device. The data collected indicates the practicality and usefulness of such a device for determining actual dragline roller circle roller loads, while the dragline is in service. The device was useful in determining roller load peaking that may be a contributing Factor in the premature failure of these thrust rollers. The device could be used for field evaluation of elastomeric cushioning materials used to eliminate these load peaks.

Jan 1, 1982