Search Documents

By Arel B. McMahan

The U.S. Bureau of Mines investigated mines, prospects, and mineralized areas in the Owlshead Mountains Wilderness Study Area (WSA) in 1982. Within the WSA, subeconomic manganese, iron, zinc, and lead resources were identified at two mines; sample analyses indicate five other mines and prospects may have gold, silver, iron, manganese, and copper resources. Three mines examined adjacent to the WSA have identified manganese and iron resources; and sample analyses indicate manganese, iron, and gypsum resources may exist at two prospects. Greatest likelihood for future identification of mineral reserves is for manganese at the Black Magic Mine in the southeast part of the WSA. The southern half of the WSA contains nearly all identified mineral resources, and properties at which sample analyses indicate additional resources. The most significant are manganese and iron resources at the Black Magic Mine in the southeastern part of the WSA; and the Ellie, New Deal, and Owl Hole Mines adjacent to that part of the area. Manganese and iron minerals filled fractures and replaced limestone in brecciated and faulted contacts with intrusive granitic rocks. In the southwest corner of the WSA, sample analyses indicate four prospects may have gold and silver resources. These precious metals are in gouge zones along contacts where diorite has intruded volcanic rocks. A small identified resource at the Kennedy Boys Lead Mine in the western part of the WSA consists of quartz veins with zinc and lead minerals along a brecciated contact between granite and limestone roof pendants.

Jan 1, 1985

By K. L. Williams

The Bureau of Mines tested a prototype tapered-element oscillating microbalance (TEOM) dust monitor for measuring respirable coal mine dust. The monitor uses the inertial behavior of a vibrating element to measure the mass of sampled dust. Tests were performed to determine variability, drift, the effect of humidity, placement of collection filter, and element orientation during analysis, and comparability with gravimetric measurements of respirable coal dust. Variability was about 1.6 µg. Over about 26 h at 46 pct relative humidity, drift was very slightly negative. When the relative humidity was increased to 78 pct, all units showed a total positive change less then 40 µg over about 70h. Filter placement variation on the tapered element resulting from in- consistent sizing of the filter mounting bases caused significant error (up to 0.2 mg). In practice, calibration of the system for each new filter will eliminate that error. Orientation of the element during analysis did not introduce significant error, but care is necessary when mounting the canister that houses the element to avoid damping oscillation of the element. Dust tests were performed in an aerosol chamber using coal dust. Measurements made by the TEOM dust monitor agreed to within 10 pct of simultaneous measurements by gravimetric personal samplers.

Jan 1, 1986

By E. W. Dean

A previous report of the Bureau of Mines* has supplied data for the physical and chemical properties of samples of crude petroleum produced in the eastern fields of the United States. It was issued as a preliminary chapter of a bulletin which is to cover the results of a survey of the entire country. The present report is a second preliminary chapter including figures that are available for the producing fields of the Rocky Mountain district. Work is being continued. with a series of samples from the States of Kansas and Oklahoma which will be described in a third preliminary chapter, to appear at a subsequent date. Acknowledgments. The obtaining of samples was rendered possible through the courtesy of representatives of a number of producing and refining companies operating in the Rocky Mountain district. The Bureau hereby acknowledges its appreciation of the hearty spirit of cooperation that was universally encountered.

Jan 1, 1921

By Joseph Berman

The wolframite mineral series was studied to determine the effect of the FeO - MnO ratio on unit cell symmetry and thermal stability. This work was undertaken to evaluate the analytical procedures now in use for wolframite in scheelite and to aid in the development of improved methods of analysis. Wolframite grains were hand-picked, crushed, and screened; impurities were removed by selective magnetic separations using a Frantz isodynamic separator. The samples were further checked by optical spectroscopic and microscopic examination.

Jan 1, 1957

By Northcutt Ely

This volume- summarizes mining and petroleum legislation in 18 European jurisdictions. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identitication of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis; of the laws governing mines and quarries and their products; third, analysis of laws applicable to natural gas, petroleum, and related materials; and fourth, mention of laws regulating offshore operations. Where pertinent, sections dealing with historical background or administration have been added in countries where minerals are subject to control of States or Provinces, those areas are considered separately from the central government.

Jan 1, 1974

By Peter D. Lohn

The Bureau of Mines conducted both laboratory and field investigations to study the effectiveness of medium-pressure (up to 30,000 psi) water jets in controlling the generation of airborne respirable dust during the hydraulic fragmentation of coal. Laboratory studies were conducted at the Farmington High Energy Test Site of the Twin Cities Mining Research Center, and field studies were carried out at the Humphrey No. 7 mine, Mount Morris, Pa., in the Pittsburgh coalbed. The water jets were produced by commercially available triplex pumps. The dust samples were collected by midget impinger samplers, and analyzed by electronic and optical counting techniques. Respirable dust concentration for a full-scale production model was projected at below 2 mg/m3, the maximum exposure allowed by the Federal Coal Mine Health and Safety Act of 1969.

Jan 1, 1975

"For a good many years the Bureau of Mines and various state mining experi¬ment stations have endeavored to develop some method of utilizing the immense deposits of lignite in the United States. Work in relent year has indicated that the best method of this is to drive off the moisture and most of the volatile water from the lignite in some form of carbonizing apparatus leaving a residue high in fixed carbon and low in moisture and volatile matter, which by briquetting can be made into a high-grade fuel. The earlier forms of carbonizing equipment tried were complicated, costly to build and keep in repair, and could not be operated intermittently without being seriously damaged. During the year 1922, however the Bureau of Mines devised a very simple carbonizing oven which produces a uniformly well carbonized product. This oven is essentially a vertical shaft with means for supplying raw lignite at the top and discharging the carbonized limited at the lower end. Air in regulated amount is admitted to the shaft at two horizons, and a zone of combustion maintained through which the column of lignite passes. The lignite is thus carbonized by construction of its contained matter and a small proportion of its fixed carbon, leaving most of the fixed carbon in the carbonized product or ""char"". The degree of carbonization can be closely controlled by varying the volume of air supplied to the oven and the rate of travel of the charre down the shaft.The ""lignite char"" produced is a soft material resembling charcoal more than coal or coke, but somewhat harder than charcoal. A typical analysis is shown in the table headed ""Fuels,"" further on in this papers."

Feb 1, 1924

By Louis E. Dalverny

U.S. Bureau of Mines research to develop diagnostic methods to locate and evaluate fires in abandoned mines and waste banks and techniques to extinguish such fires was applied to an abandoned 60-acre underground bituminous coal mine (Renton, Allegheny County, PA) to locate and extinguish three separated fire zones. Mine fire diagnostics interpret changes from baseline values in subsurface pressures, temperatures, and mine gas composition under imposed pressure gradients induced by a borehole exhaust fan. The effective gas sampling area surrounding each borehole is greatly enlarged. Sampling iterations, using a "communicating" boreholes set, provide "fire signature" information for locating both heated and cold areas. Time-dependent monitoring differentiates heating and cooling periods resulting from combustion front movement and/or fire extinguishment activities. A water injection with fume exhaustion extinguishment effort involved injecting water through boreholes to quench the heated zones while exhaust fans actively removed heated gases from the mine. The technique was ineffective as implemented, primarily because of inadequate spreading of water from the injection points. The Bureau's diagnostic method determined the fire locations and the effectiveness of the water injection with fume exhaustion extinguishment technique.

Jan 1, 2010

By Robert E. Wood

The temperature dependency of the low-density viscosity coefficients, ?°T, of helium and of nitrogen, 100° to 1,000° K, is correlated with empirical equations, and the temperature and composition dependencies of the low-density viscosity coefficients, ?°T, of helium-nitrogen mixtures are correlated with the Chapman-Enskog expressions by using the Lennard-Jones (6:12) potential function. The residual viscosity, ?T,P - ?°T (the difference between the viscosity of a compressed gas and the dilute gas at a given temperature), was found to be a function of the thermal pressure coefficient, (?P/?T)V, and two parameters, a and 1, which are characteristic of gas composition. The equation ?T, P = ?°T + a [(?P/?T)V]ß represented 1,340 higher pressure experimental viscosity values with a mean absolute deviation of 0.86 percent, and this equation was used to compute viscosities of the gaseous helium-nitrogen system for a range of temperatures and pressures including those encountered in Bureau of Mines helium purification processes and in a crude-helium conservation gas reservoir. Tabular viscosities for helium, nitrogen, and 13 helium-nitrogen mixtures are presented for 110 temperatures, 133° to 740' K, and 49 pressures in the range 1 to 240 atmospheres. The accuracy of the tabulated viscosities varies because correlation parameters were obtained from experimental data of unequal reliability. It is estimated that uncertainties in the computed viscosity values are ±5 percent for the region 325° to 740° K, ±2 percent for the region 183° to 325° K, and ±5 percent for temperatures below 183° K. The latter uncertainty may rise to y10 percent as critical conditions are approached.

Jan 1, 1970

By J. W. Chester

The rapid depletion of zinc-lead ore reserves and the rising costs of exploration have been major factors in the decline of mining activities and explorations for additional reserves in the Tri-State mining district. There is a need to develop new or adopt known, improved exploration techniques that will appreciably lower the costs of exploration. Demonstration of the practicability of using improved techniques to indicate, rapidly and cheaply, mineralized areas or geologic structures where more intensive explorations are justified could stimulate the search for and discovery of additional ore reserves. Various operators in the Tri-State district have used geophysical surveys to some extent since 1928 to guide exploratory drilling. Some geophysical investigations have also been made in the district by the State Geological Surveys of Kansas (11)3/ and Missouri (8, 13) and by Federal agencies (16), with the objective of directing exploratory drilling to areas where geologic conditions favored ore deposition. Many factual data obtained have not been published. The investigations generally have not been broad enough to permit conclusive evaluation of the usefulness of the geophysical techniques in all parts of the district.

Jan 1, 1959

By John Nagy

Dust explosion data obtained in laboratory tests by the Bureau of Mines are presented for 181 miscellaneous materials that present an explosion hazard. Data are given also for 50 dusts that present primarily a fire hazard and for 88 dusts that did not present an explosion hazard.

Jan 1, 1968

By H. A. Watson

Laboratory tests on three commercial methane detectors, two combustion-type detectors and one interferometer-type detector, were made by the Bureau of Mines to determine their response to certain single and multiple flammable gases mixed with normal and abnormal air atmospheres. Although both types of detectors responded accurately to methane-normal air mixtures, they did not show correct concentrations for other single flammable gases in air. Uniquely, the response of the interferometer-type detector to hydrogen was in a negative direction. The effects of individual gases in multiple flammable gas mixtures were approximately additive. In oxygen-deficient atmospheres the methane response of the interferometer-type detector erred on the high side, but only in very low oxygen concentrations were the combustion-type detectors affected-showing low, erratic methane readings.

Jan 1, 1966

By Arno C. Fieldner, Howard I. Smith, J. W. Paul, SAMUEL SANFORD.

Many mine samples of coal are analyzed each year in the laboratories of the Bureau of Mines. The analyses are made in connection with investigations relating to fuels belonging to or for the use of the United States Government, the causes of accidents in coal mines, the geologic relations of coal beds, and the character and the value of the coal and lignite in the public lands. The systematic collection and analysis of such samples in connection with fuel investigations was begun in 1904 at the Government fuel-testing plant at the Louisiana Purchase Exposition, and was under the direction of the United States Geological Survey for six years. Descriptions of the coal samples collected between the beginning of this work, July 1,1904, and the transfer of the fuel-testing and mine-accident investigations to the Bureau of Mines, July 1, 1910, were compiled and published in Bureau of Mines Bulletin 22.a Descriptions and analyses of samples collected during the fiscal years 1911 to 1913 were published in Bureau of Mines Bulletin 85.b The present bulletin presents analyses and descriptions of samples collected during the fiscal years 1913 to 1916. In order that the material in this bulletin may be used to supplement that presented in Bulletins 22 and 85, the same plan of geographical classification has been followed, the analyses and descriptions of the samples being grouped in alphabetical order according to the State, county, and town near which the mines or prospects sampled are situated.

Jan 1, 1918

By Charles Vaught, Jeff Duncan, Michael J. Brnich, Lisa J. Steiner

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.3 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Remote control and extended cut miner operators and face crews Length: Eight questions (30 minutes for administration plus 30 for discussion) Skills: Remote control mining procedures including remote control mining, taking extended cuts, resetting breaker on mining machine, and setting timbers. Communicating mine conditions, influencing safe behaviors when mine conditions are less than stable Location: Underground coal mine, four section continuous mining operation Average seam height is 48 inches Problem: Your regular job is on the general labor crew at Cripple Creek #9 mine, a four section continuous mining operation. The mains are 9 entries wide and panels are 5 entries across. You and the rest of the crew had annual refresher training about 3 months ago. For the past few days you have been sent to 2 South panel to fill in as the third shuttle car operator. This morning, however, your buggy is down. The face boss asks you to get the scoop and take seven or eight timbers to the number 5 entry because the last shift got off sight line. The miner will be working in entry 5 while the bolter crew pins entry 4. When you get up to the face you see that Mo, the remote control continuous miner operator, has rounded off the left inby corner in order to make his first cuts in the right hand rib. Now, he has squared around enough so that you and Red, the miner helper, can set some posts on the corner. The two of you set posts along the left inby rib of #5 entry while the shuttle car operator waits. You are in a tight spot when Mo decides to start mining. You must decide where the best place is to stand for safety and to be out of the way.

Jan 10, 1999

By E. L. Garton

Bureau of Mines routine crude-oil analyses of 88 samples from 60 fields are presented in this report. Similar analyses from other fields in California have been published in previous reports listed in the appendix, page 52. Yearly production of crude oil in California and the percentage of United States production represented by California production for 1948-54 are given in table 1. [ ] Analyses in this report are of samples from the fields listed in table 2, with production data for 1953, cumulative production through 1953, and year of discovery of each field. Information regarding the source and general characteristics of the samples is included in table 3 with a summary of analytical and computed data.

Jan 1, 1956

By Isaac A. Zlochower, Michael J. Sapko, Ronald S. Conti

The Bureau of Mines has developed a system using a high-speed electropneumatic mechanism for the rapid (grab) sampling of dusts and gases during an explosion. The sampling system consists of an aluminum housing that incorporates two 30-cm3 preevacuated glass vials with rubber septums. Upon actuation, the sampling probe needle is driven through the septum with a pressurized air pulse, filling the tube with gas and dust from the mine explosion. After a predetermined time, the sampling probe needle is retracted by a second high-pressure air pulse to its normal (quiescent) state, allowing the sampling tube to reseal. The onset and the duration of sampling are independently variable and controlled by a time-delay relay package. This technique enables the monitoring of pyrolysis-charring in coal particles and the generation and combustion of the pyrolysis vapors in both large- and small- scale explosions. The following results were obtained from full-scale dust explosion tests at the Bureau of Mines Lake Lynn Laboratory: (1) Gas sampling of the leading edge of the flame front shows the large concentration changes, characteristic of the flame front; (2) gas samples taken entirely in the flame zone consist of pyrolysis and combustion products with very low residual oxygen; and (3) the particles collected in the flame zone show signs of extensive pyrolysis and charring.

Jan 1, 1988

By Charles Will Wright

This paper will be of interest to those who are actually developing a mineral prospect or planning to do so, as well as to investors who are considering the problem of financing the development of the prospect, so that they may know what the risks are and what capital expenditures are necessary before a prospect may become a mine. The term "prospect" used broadly, as it is in this paper, is defined as any property that has a mineral showing of sufficient interest to warrant development, irrespective of prior work, Such previous exploration, however, may be extensive and consist of several tunnels or adits connected by raises, or of shafts with several levels. There may also be a small mining and milling plant on the prospect which, because of the lack of capital for development or the lack of markets for the products, is now idle. Such prospects may warrant further capital investment for development work or for a mine plant to raise to the stage of profitable production.

Jan 1, 1935

By S. J. Rodgers

MSA Research Corporation, Division of Mine Safety Appliances Company, was awarded a contract to conduct a survey of past and present methods used to control respirable dust in noncoal mines and ore processing mills. The survey covered information reported in mining journals, and U.S. Bureau of Mines Circulars, dust inspection reports, on-site evaluation of dust control methods and systems, and contact with manufacturers of dust control equipment. Both surface and underground mining operations were visited. Fifty mines and 51 processing plants were included in the survey. Dust control methods for the following types of ores or mines were studied: [ ]

Jan 1, 1974

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point, out the need for corrective measures, the Bureau of Mines collects, analyzes, and periodically publishes health and safety statistics. This report includes data for 1962 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1964

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and periodically publishes health and safety statistics. This report includes data for 1962 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1964