Search Documents

By David H. Yee

Because of environmental concerns, the Bureau of Mines investigated an anhydrous chlorination process for the recovery of copper from chalcopyrite, Pelletized concentrate was reacted continuously with chlorine in a vertical shaft reactor at 550° to 750° C to extract copper-iron chlorides and elemental sulfur. The resulting molten metal chlorides drained from the reactor and collected in a receiver while sulfur distilled from the top and condensed in a separate unit. The tests were conducted in a 10-cm-diam reactor constructed of glass and in l5-cm-diam reactors constructed from various refractory materials. A high-alumina ramming mix exhibited the best resistance to molten metal chlorides and elemental sulfur in chlorine atmospheres. A reactor made with this high-alumina refractory was operated for 55 hr under actual chlorinating conditions without suffering any deterioration. Tests results show that more than 96 pct of the chalcopyrite was converted to copper-iron chlorides and elemental sulfur. Good separation of the metal chloride and sulfur products was achieved. After filtration, elemental sulfur of greater than 99 pct purity was obtained.

Jan 1, 1977

By Christopher Mark

Roof bolt system design means the selection of the type, length, capacity, and pattern of bolts for a particular application. Despite research efforts dating back 50 years, no design methodology has found wide acceptance. This paper begins by identifying four mechanisms that roof bolts use to reinforce the ground. It argues that the reinforcement mechanism is determined by the roof geology and stress level, not by the type of bolt. Next, the attributes of roof bolts are discussed in the light of recent research, including anchorage mechanism, installed tension, length, capacity, timing of installation, and installation quality. Several significant areas of controversy are identified. Design methods from around the world are discussed, including those based on empirical research, numerical modeling, and roof monitoring. Finally, some simple guidelines for preliminary design of roof bolt systems are proposed based on statistical analysis of roof support performance at 37 U.S. mines.

Jan 10, 2000

By Charles L. Kusik

As part of an effort to establish the extent of the domestic chromium supply that could be exploited in case of adverse changes in international chromium production and trading patterns, a two-part study was conducted for the Bureau of Mines, to assess the domestic availability of critical metals in scrap containing significant amounts of chromium. This report describes the part of the study that deals with wrought stainless steels and heat-resisting alloys. Data were collected on types of scrap, sources, quantities, and ultimate disposition, leading to the conclusion that In 1917 about 62,000 tons of contained chromium was unrecycled. Unrecovered obsolete stainless steel scrap accounts for most of these uncollected chromium values. Error margins in the amount of uncollected scrap are estimated to be 10 to 20 percent.

Jan 1, 1980

By W. C. Holliman

This second of a series of reports on the characteristics of commercial aviation gasolines presents inspection test data furni8hed on their products by 15 manufacturers of commercial grades of aviation gasoline and special data obtained in Bureau of Mines laboratories on samples of these gasolines. Data on 18 grade-80, 20 grade-91/98, 20 grade-100/130, and 9 grade-115/145 aviation fuels are presented. These gasolines represent July 1947 production.

Jan 1, 1948

By Wallace W. Roepke

The Bureau of Mines studied the cutting characteristics of point-attack bits to reduce airborne respirable dust and energy during cutting. Linear cutting of two coal types using four bit types at three depths of cut with three space-depth ratios was performed with a modified horizontal milling machine using an optical particle-size monitor for respirable dust sampling. The cutting action of one bit on a rotary hardhead mining machine was mathematically analyzed and compared with the results of the linear cutting test. Airborne respirable dust per unit mass cut (specific dust) was found to be a monotonically increasing function of specific energy. Specific dust and energy decrease with increasing depth of cut. The amount of nonairborne respirable dust was 100 to 1,000 times greater than the airborne dust. The plumb-bob bit produced the most airborne respirable dust and the highest specific energy of the four bits tested. Rotary cutting was a greater dust producer and energy consumer than linear cutting because of the constantly changing depth of cut, space-depth ratio, and attack angle of the bit relative to the horizontal bedding planes. A new cutting technique is proposed to minimize the existing problems of the rotary cutting machines by providing greater production, reduced dust, and minimized methane ignition potential at the face.

Jan 1, 1976

By A. D. Mah

To assist Bureau of Mines research in extractive metallurgy and to add to the thermodynamic data base useful to others, energy calculations were made for 63 reactions relating to investigations on the production of anhydrous aluminum chloride from chlorination of clay.

Jan 1, 1982

In 1967 the United States consumed 58.8 quadrillion Btu of energy. Both the Atomic Energy Commission and the Resources for the Future, Inc., a private economic forecasting group, predict that the United States energy requirements will reach 135 quadrillion Btu by the year 2000. In 1967 bituminous coal produced 21.4 percent of the energy used in the United States and anthracite coal another 0. 5 percent. Coal Reserves Coal reserves make up about four-fifths of the United States storehouse of fuel in proven reserves. Seventy-five percent of all fuel, likely to be found and recovered is coal. Electric utilities consume more than half of the bituminous coal mined in the United States in generating 53 percent of the nation's electricity. Atomic Energy Commission analysts have proposed the development of a vast "national energy system" based upon long-distance electrical transmission from abundant untapped coal reserves in the western United States. The study predicts that even if uranium supplies are available and economic breeder reactors developed, coal requirements for electricity generation will more than double by 1980 and increase another 50 percent before the year 2000.

Jan 1, 1970

By B. W. Gandrud

The upper part of the Alabama deposits of crystalline graphite consists of an oxidized ore derived from the underlying unoxidized ore through prolonged Weathering. The degree of oxidation in different sections and at different depths within the bed is not uniform. The original ore is hard and blue-gray; the weathered product is soft and brown and is the only part that has been mined to any extent. Samples of both oxidized and unoxidized ores were obtained from two of the large graphite deposits of Clay County. Three additional samples of oxidized ore were obtained from different portions of a third property in the same region. In this report, ores 1 to 5 are of oxidized material and ores 6 and 7 of unoxidized.

Jan 1, 1934

By James J. Snodgrass

The Bureau of Mines designed and constructed a series of calibration models for geophysical borehole logging. A nominal hole diameter of 3 inches was selected as representative of typical core holes drilled for mining and engineering purposes, although additional hole diameters of 2, 5, and 8 inches are provided in one of the models for determination of empirical correction factors for variations in hole diameter. The physical properties of the models were determined by laboratory analyses of drill core samples and evaluated statistically for reliability. This report outlines the location of the models, elements of design and construction, and results of the laboratory tests. The models are available at the Denver Federal Center, Denver, Colo., for use by Government agencies and private industry to calibrate logging equipment for measurements of density, sonic velocity, magnetic susceptibility, and electrical resistivity.

Jan 1, 1976

By C. W. Owings

The number of major coal-mine explosions occurring annually in the United States is decreasing, due mainly to fuller recognition of explosion hazards in coal mines and knowledge of methods to prevent them, which can be attributed largely to the dissemination of information by the United States Bureau of Mines, State departments of mines, and other coal-mining agencies. Conditions vary considerably from one coal field to another; consequently, outstanding causes of and methods of combatting explosions vary, also. The Safety Division of the United States Bureau of Mines is making a critical study of coal-mine explosions in the various coal-mining States, and an analysis of the results is published as each study is finished. It is believed that, with completion of the series enough information will be at hand which, if applied, will prevent all coal-mine explosions. ACKNOWLEDGMENTS The data in this circular are based on records of the United States Bureau of Mines and the Industrial Commission of Ohio. The cooperation and assistance of T. P. Kearns, superintendent of the Division of Safety and Hygiene of the Industrial Commission of Ohio, and of James Berry, chief inspector of the Division of Mines of Ohio, is acknowledged.

Jan 1, 1937

By Michael V. Markel

This report summarizes work performed under USBM Contract No. J0100047 revealing the performance characteristics of a composite-type resilient screen deck. The ability of the composite to perform or compete with steel in noise attenuation and longevity was of interest. Tests were conducted at the River King Preparation Plant of Peabody Coal Company. This facility was chosen because it provided parallel process flow and met standard coal cleaning requirements. Comparisons could be made between the adjacent resilient and steel screen decks under similar operating conditions. Noise reductions of 1-6 dBA were realized in the near field. Although the test period did not determine resilient screen life, indications are favorable for their longevity.

Jan 1, 1981

By d&apos, Kathleen J. Amico

THIS SUMMARY is identical to the summary given in volume III of this series of mineral production in the United States (including Alaska and Hawaii), its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico and of the principal minerals imported into and exported from the United States. For further details on production see commodity and area chapters. A summary table comparing world and United States mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers [ ]

Jan 1, 1958

By R. E. Morgan, Barkleym J. F.

"INTRODUCTION Wood burned for commercial heat and power usually is waste material from some manufacturing process. The amount of it reaches substantial proportions. It is estimated that over 50 percent of the timber cut for lumber becomes ""waste"" in the process - sawdust, shavings, trimmings, slabs, and bark. Woodworking manufacturing processes also produce much waste. The incentive to use this waste has resulted in much development of wood-burning equipment to produce heat and power. To answer general inquiries received by the Bureau, this publication covering developments along these lines was written. There is included a bibliography of additional information on the subject.COMPOSITION AND BURNING CHARACTERISTICS OF WOODThe approximate composition of moisture-free wood is, in even figures:PercentHydrogen 6Carbon 49Oxygen 44Ash 1Total 100This composition corresponds to about C6H1005. Moisture is essentially always associated with wood. Green wood contains approximately 30 to 50 percent moisture; air-dried or seasoned wood contains 15 to 25 percent and kiln-dried about 8 percent. Exposed to the weather, wood absorbs and gives off moisture depending on weather conditions and water contact.""Dry"" wood ignites relatively quickly and readily gives off volatile matter when heated. Long flames and smoke easily occur during burning. The burning action is substantially retarded, however, by appreciable moisture content; ignition is more difficult. When the moisture content is more than about 70 percent, an auxiliary fuel is required to maintain combustion. One of the main factors in the problem of the satisfactory and smokeless combustion of wood is its moisture content."

Sep 1, 1950

By M. A. Mahtab

This report presents a new procedure for analyzing the orientations of rock fractures in an engineering site. This procedure, coded in a computer program, identifies clusters or groupings among the fracture orientations and calculates (1) the mean orientation of the fractures within each cluster and (2) the dispersion or scatter among these fracture orientations. Data points are represented by intersections of joint normals with the upper hemisphere, which is divided into 100 equal-area quadrilateral patches. The points in adjacent patches where the Poisson distribution test shows significant concentrations are assigned to a single cluster. For a cluster whose fracture orientations follow Arnold's hemispherical normal distribution, a confidence interval for the fracture orientation mean is calculated by applying Fisher's estimates. The technique is applied to the treatment of three examples.

Jan 1, 1972

By A. J. Kraemer

[The Bureau of Minas for a number of years has been studying the properties of crude petroleum from producing fields in the United States and Western Hemisphere and has published a series of reports on these fields, including oil fields of Texas.5]

Jan 1, 1927

By P. E. King

The U.S. Bureau of Mines is conducting an ongoing research project to better understand the phenomena involved within electric arcs utilized in electric furnace steelmaking. With a better understanding of the physical and electrical characteristics involved, dynamic or predictive control of electric arc furnaces may be possible. A mathematical model is presented, but not solved, and the system of coupled equations is analyzed. Characteristic parameters are used to determine relative importance. In this manner, significant quantities are dermed. The parameters found to contribute little to the system of equations of motion are ignored. A resultant simplified system is identified, and directions for further study are indicated toward control of electric arc furnaces.

Jan 1, 1990

By Ivor Hawkes

The purpose of the development described in this report and as stated in the contract work statement is to "design, develop, fabricate, test and demonstrate, and deliver to the government permissible low cost cylindrical stress gauges and associated components capable of measuring change of stress as a function of time in underground coal mines. The cylindrical stress gauges shall be suitable for installation in bore holes". The technique adopted for measuring rock stress changes is to preload a steel cylinder diametrically across the sides of a 1-1/2 in diameter bore hole and detect deformation of the cylinder from stress changes in the rock, by means of a vibrating wire transducer. By calibration, changes in the period (time for one wire oscillation at the natural frequency) of a high tensioned wire stretched diametrically across the cylinder in the direction of load application are related to stress changes in the rock. To completely evaluate the stress field change in the plane of the bore hole, three gauges set at an angle to each other are required.

Jan 1, 1973

By R. E. Heithecker

[The separation of enormous quantities of water produced with the oil in some West Texas fields necessitated. the use of special equipment other than the regular lease tanks. Several methods Were used with varying degrees of success. They include, the water-trap, hay tank and gun barrel, gun barrel and settling tank, chemical, and electrical-dehydration methods. The water trap which has been used extensively in the Hendricks field, and in some instances has been installed in the Yates field separates the water' and. oil under high pressure before tile liquid and gas pass through the flow ?bean. The first trap was constructed and installed by the Southern Crude Oil Purchasing Co. in July, 1928. By July, 1929, approximately 300 traps were in use.]

Jan 1, 1932

By R. E. Heithecker

The separation of enormous quantities of water produced with the oil in some West Texas fields necessitated the use of special equipment other than the regular lease tanks. Several methods were used with varying degrees of success. They include the water-trap, hay tank and gun barrel, gun barrel and settling tank, chemical and electrical-dehydration methods. The water trap which has been used extensively in the Hendricks field, and in some instances has been installed in the Yates field separates the water and. oil under high pressure before tile liquid and gas pass through the flow beam. The first trap was constructed and installed by the Southern Crude Oil Purchasing Co. in July, 1928. By July, 1929, approximately 300 traps were in use. Treating cut oil by running it through a hay tank was done quite extensively in the Roberts-Settles field, Howard and Glasscock Counties, Tex., and later the method was used in the Hendricks field. In July, 1931, there were 37 hay tanks in the Roberts-Settles field, treating the oil from 123 wells. The cut oil frequently was made acceptable to the pipe-line company by running it through the hay tank. In some instances, however, it was necessary to heat the oil, and occasionally both heat and chemicals were used before complete separation of the oil and water was obtained.

Jan 1, 1932

By Willard J. Tesch

The borehole surveying system described is used to measure ground movement over and near operating mines. The magnitude of any movement is con-trolled by the ground conditions, the mining method, and the mine progress. By correlating these factors with the measured movement, equations can be determined for predicting the effect of mine progress on the surrounding ground. These equations can also be used to predict the effect of mining a similar deposit with similar ground conditions. The borehole surveying system is used in cased boreholes to measure the inclination of the hole in two perpendicular planes. Grooved casing with an inside diameter of 3 inches is grouted in the hole. Two probes are used to obtain the data necessary to calculate the hole position versus depth. One of the probes contains a gyroscope, and the other contains a biaxial force-balance [s]ervoaccelerometer. Readings from the transducers in the probe are punched on paper tape by an automatic data acquisition system as the probe is pulled up the hole at 30 feet per minute by an electric winch. Readings from the inclinometer probe containing the accelerometer are used as input data to an on-line programmable calculator as they are punched on tape. The calculator computes preliminary results of the survey being made. The paper tapes obtained during the survey runs are later used as input to a computer that computes the offsets of the drill hole versus depth in true north-south and east-west planes. These offsets are printed for each foot of depth. Changes in these offsets between the first survey and subsequent surveys are a measure of the horizontal ground movement between the surveys.

Jan 1, 1976