Search Documents

By Graham W. Marks

The general positions of the absorption maxima of aqueous solutions of the violet and green isomers of chromic sulfate the visible spectral region have long been known, but, to the knowledge of the writer, no comprehensive studies have ever been made. To gain further knowledge concerning these inorganic complexes and to investigate the possibilities of developing an analytical method for determining the concentrations of the violet and green isomers in a mixture, a more complete investigation was made in the spectral range from 325 to 850 millimicrons.

Jan 1, 1951

By D. H. Zellers

Since its inception the United States Bureau of Mines has fostered the development of portable mine lamps. Although there is still much to be desired with respect to illumination in coal and metal mines and the replacement of open lights has been slow the Bureau has been given credit for assisting materially in the development and introduction of the safe and efficient portable mine-lighting equipment available today. Much of the work conducted by the electrical section of the Bureau entails approval tests of various types of electrical equipment, including lamps; to be used in atmospheres that may contain methane or coal dust in explosive proportion. If a can lamp meets the requirements-for safety, efficiency, and adequacy, as published in Schedule 6B,4 it is approved and is generally known as a "permissible" lamp. The terms "approved" and '"permissible' often are used interchangeably. The manufacturer must put an approval plate on each approved lamp, showing it has mot the schedule requirements. The approval plate is not a guarantee that the lamp is safe. However, if the lamp, once in service, has not had any parts changed or improperly assembled or if carts that wear out or depreciate have been properly replaced it should still, be safe, efficient, and adequate for the service intended. Virtually all electric cap lamps in service today in the United States and a great many that have been sent to foreign countries bear the approval plate of the United States Bureau of Mines. Although many explosions have been attributed to open lights none has been charged against the permissible cap lamp. Nystagmus, a disease of the eye attributed to working under insufficient illumination, is practically unknown among; American miners, although it is quite prevalent among European miners.

Jan 1, 1935

By Rogers F. Davis

This publication has been prepared to supply manufacturers and industrial users a listing of mobile diesel-powered transportation equipment approved or certified by the Bureau of Mines f r use in gassy noncoal mines and tunnels. Testing of diesel-powered equipment is one phase of the Bureau's health and safety program of approval of electrical and diesel equipment designed to prevent explosions, fires, shocks, and toxic hazards in underground mines. In mines such equipment must be used and maintained properly. Manufacturers submit machinery and component parts to the Bureau for study f their design and safety features. Equipment must pass exacting tests and meet strict requirements established through research, development, and experience before the Bureau approves it as permissible for safe use in mines.

Jan 1, 1967

By James S. Browning

The Bureau of Mines conducted laboratory batch and small-scale continuous selective flotation tests of barite-fluorspar ores from two deposits near Marion, Ky., to determine the technical feasibility of recovering commercial grade fluorspar and barite concentrates. The lignin sulfonate-sodium fluoride method of floating the fluorspar successfully produced acid-grade fluorspar concentrates. Flotation of the barite from the fluorspar tailing using petroleum sulfonate collector yielded concentrates suitable for use in compounding oil-well drilling mud. The fluorspar and barite recoveries were about 82 and 85 percent, respectively.

Jan 1, 1963

By Paul M. Tyler

One of the best present-day yardsticks of the material welfare of a nation is its consumption of minerals, The United States, with only 7 percent of the world population, consumes 45 percent of the world wealth, pays the highest real wages, has the shortest working hours, and numbers the largest percentages of home owners among its population, and at the same time its per-capita consumption of minerals is far greater than that of any other nation. In 1937, British India, with roughly twice the population of the United States, used less than 2 percent as much lead, 4 percent as muck zinc, and 13 percent as much copper; even in Europe, which has three times our population and where war preparations have greatly expanded the normal needs of peaceful industries, the aggregate consumption of metals and industrial minerals other than lignite is less than the total for the United States alone. The march of civilization passed from the Stone Age to the Bronze Age before the dawn of history. It may be questioned whether man or monkey first threw stones at an enemy, but only man could have fashioned rough stones into weapons. Eoliths rudely shaped by apelike men are believed by archaeologists to have antedated by hundreds of thousands of years the existence of our own human ancestors. The primitive people that followed the retreating Ice Cap northward in early quaternary period - at least a million years ago - were fairly adept in the shaping of flints and even used a little copper. The Bronze Age, so-called, superseded the Stone Age when, around 8,000 B. C., the news spread that chunk s of natural copper could be pounded into better weapons or cutting implements than ever could be made by chipping stones. The Bronze Age gave place to the Iron Age about 1,000 B, C., and though students of modern history may speak of the Coal Age, the Petroleum Age, and the Automobile Age, and so on, these ages have all been crowded into a brief century and a half. The truth is that we still are in the Iron Age, unless perhaps we choose to call it the Age of Many Metals.

Jan 1, 1940

By G. Richards Gwinn

The mineral olivine, though known to mineralogists for many years, was of little commercial value in the United States before 1933. It was first described in 1790 by Johann Gottlieb Werner, who named it "olivine in allusion to its olive-green color. Commercial olivine first attracted attention because of its refractory properties. Further research has developed methods of extracting the magnesia content for the production of various magnesium compounds. Experimental and pilot-plant work also are in progress to make olivine available as a low-cost raw material for the production of magnesium metal.

Jan 1, 1943

By Richard L. D?Arcy

This paper describing the mining practice and methods at the United Verde Extension mine, Jerome, Ariz., is one of a series of papers in preparation by the Bureau of Mines presenting the mining methods used in various mining districts of the United States. The United Verde Extension mine is a massive, high-grade deposit of copper sulphide containing some gold and silver and is mined almost exclusively by the conventional square-set method with some local modifications. About 450 men are employed underground and 1200 tons of direct smelting ore is produced per day. Figure 1 is a surface map of the Jerome district.

Jan 1, 1930

By P. G. Guest

"INTRODUCTION Need for More information on Spark IgnitionMany questions have yet to be answered more completely concerning the ignition of flammable gases and vapors by electric sparks. Among these one might mention the following: How do the mixture limits for ignition by sparks and by other means compare? Are the most explosive mixtures of the gases the most easily ignited? How ""hot"" must the spark be or what is the minimum energy required for ignition? Does the electric spark act merely as a source of thermal energy or do aggregations of ions, electrons, and metastable atoms formed during and just before the spark play an important part in promoting chemical reactions that ultimately lead to ignition? It is possible for ignition to occur as a result of a silent or brush discharge? How do the ignition energies with single and rapidly recurring sparks differ? What is the relative effectiveness of long, tenuous sparks in ignition as compared with intense, short-gap sparks of equal energy? What is the influence of the material, size, and shape of the spark electrodes? Does the energy for ignition change noticeably with moderate changes in pressure and temperature of an enclosed gas mixture? What order of lag exists between the occurrence of an incendiary spark and the first evidence of flame propagation? What part of a spark in space and time is most effective in producing ignition? Answers to these questions bear directly on the general problem of flame initiation and propagation and, if sufficiently comprehensive, should contribute much to an understanding of the actual mechanism of combustion."

May 1, 1944

By James C. Cawley

The Bureau of Mines conducted an investigation to statistically determine the mean current or voltage for resistive, inductive, and capaci-tive circuits that would cause spark ignitions in 8.3% methane-air, 5.3% propane-air, and 7.8% ethylene-air mixtures. Each mean ignition current or voltage was determined on the basis of 100 trials. Each trial consisted of 400 revolutions, 200 in each polarity, at 80 rpm of the standard breakf1ash apparatus. In general, spark ignition curves published in UL 913 for resistive and inductive circuits represent approximately the mean current values determined in this study, while published capacitive circuit values in methane are considerably less than the mean voltage values from this study, especially for a capacitance of less than 100 ~F. For resistive and inductive circuits, spark ignitions were obtained at currents con-siderably below those in the published curves, but this study was not optimized to find minimum ignition values. This report defines "safety factor" as applied to intrinsic safety testing as the energy ratio of the mean values of ignition current or voltage for two test gases. The safety factors presented in this report are not constant with voltage or current and, therefore, are not recommended for use.

Jan 1, 1986

By R. H. Reist, R. D. Dey, V. Castranova, J. P. Durham, Y. Rojanasakul

"Silicosis is a fibrotic pulmonary disease produced by inhalation of silica-containing dusts (Peters, 1986). Chronic silicosis may develop 20-40 years after initial exposure to crystalline silica, and the disease may progress from a simple to a complicated form. Few symptoms are evident in simple silicosis with pulmonary function being relatively normal. However, chest radiographs reveal small rounded ·opacities in the upper lobes of the lungs. These silicotic nodules consist of collagen arranged in a distinctive circular pattern. As fibrotic changes become more severe, the disease progresses to complicated silicosis (progressive massive fibrosis). Complicated silicosis is associated with shortness of breath and decreases in pulmonary function characteristic ofrestrictive lung disease. Chest x rays reveal numerous large silicotic nodules which may be associated with scar emphysema. Several mechanisms have been proposed to explain the cellular events which result in silica-induced lung damage and fibrosis (Lapp and Castranova, 1993). They include: ( l) direct cytotoxicity of silica, (2) activation of oxidant and enzyme release from alveolar macrophages, (3) recruitment and activation of polymorphonuclear leukocytes, and (4) stimulation of fibroblast proliferation and collagen synthesis.Tetrandrine is a bisbenzylisoquinoline alkaloid derived from the Chinese herb Radix Stephania tetrandra. It has a molecular weight of 622.73 and an empirical formula of C38H420 6N2. The chemical structure of tetrandrine has been published previously by our laboratory (Castranova et al., 1991 a). Its structure is characterized by methoxy groups at C7 and C12 , uncharged nitrogens at N2 and N’2 and two 17-carbon ring members connected by a double oxygen bridge between Ca-C7 and C11-C12. Tetrandrine has been shown to reduce both silica-induced fibrosis and the elevation of lung collagen content in rats (Huang et al .. 1981; Yu et al., 1983; ldel, 1987). Furthermore, tetrandrine has been used as an antifibrotic agent in Chinese clinical trials (Li et al.. 1981 ). Preliminary results suggest that administration of tetrandrine to patients with silicosis results in substantial improvement of symptoms, increases in diffusion capacity, and decreases in the size of shadows on lung x rays."

Nov 1, 1995

By Verne E. Hooker

The Bureau of Mines conducted a preliminary investigation to determine the state of stress in crystalline rock outcrops near Atlanta, Ga. The secondary principal stresses in a horizontal plane near the surface are compressive and are 500 to 3,000 psi. The maximum compressive stress is northeast-southwest in the Stone Mountain-Lithonia district but changes to northwest-southeast near Douglasville. The elastic constants were determined from data obtained by static and dynamic laboratory methods and in situ velocity measurements. Results show Young's modulus to be dependent upon both stress level and anisotropy in the rock. Average secant moduli obtained from triaxial tests were used to compute the applied stress from borehole deformation measurements.

Jan 1, 1966

By Christopher J. Bise

Volume II of this collection of research reports, entitled "Model Training Program," provides the framework and details for developing a tailored training program for a specific mine based upon documented human-performance deficiencies. To do this, several steps must be followed prior to program implementation: 1) background information must be gathered (database analysis), 2) direct observation of indicated problem areas should be conducted (safety sampling), and 3) separation of those deficiencies to be addressed through training from those which would be better addressed by workplace or equipment redesign (trainability assessment). Once training is determined to be the appropriate strategy for addressing the noted deficiencies, several approaches can be taken, depending upon whether the problem is related to repetitive work procedures in a predictable, a variable, or a dynamic workplace with a substantial amount of interaction between workers, equipment, and the environment. Although this volume and the subsequent seven volumes provide examples of how the training information was field tested using various strategies (for example, loss control, task training, etc.) and techniques (for example, microcomputer-based exercises, lectures, etc.), the ultimate selection of the delivery method is based on cost/benefit analysis. Therefore, the Model Training Program has incorporated a Training Cost Model as a desirable component.

Jan 1, 1993

By C. J. Wilhelm, John M. Devine, Ludwig Schmidt

"Steel tanks often corrode rapidly in oil fields where the Gas produced with crude contains an appreciable quantity of hydrogen sulphide. In many instances working tanks have been discarded after only six months of service because of failure induced by corrosion.Aluminum has been used for some time in the fabrication of certain equipment incidental to the handling of oils containing hydrogen sulphide gas in solution, and has exhibited no carious corrosive action. These uses indicated that aluminum tanks,be equally effective in counter- acting hydrogen sulphide corrosion. Consequently, in the spring of 1920, an all-aluminum stock tank of 500 barrels capacity and a ""composite"" tank of equal capacity, having a steel bottom and bottom ring and an aluminum top and top ring, were placed in service on the State-Lassiter lease of the Gulf Production Co, in Crane County, Tex. These tanks were under observation for one year, the toot being sponsored by the Gulf Production Co., the Aluminum Co. of America, and the Parkersburg Rig and Reel Co. The results of this preliminary test sustained the belief that aluminum is highly resistance to hydrogen sulphide gas and likewise indicated the type or grade of aluminum which could be most economically used for lease tankage. However, in this preliminary test the tanks were not subjected to contact with the quantities o highly concentrated brines such as often are associated and produced with crude oil. Therefore, it was suggested by representatives of the aluminum Co. that additional tests be made to include production conditions in large quantities of brine would be handled, for pact experience had shown that aluminum often is susceptible to the corrosive action of brines."

Apr 1, 1931

By Ludwig Schmidt

[Steel tanks often corrode rapidly in oil fields where the gas produced with crude petroleum contains an appreciable quantity of hydrogen sulphide. In many instances working tanks have been discarded after only six months of service because of failure induced by corrosion. Aluminum has been used for some time in the fabrication of certain equipment incidental to the handling of oils containing hydrogen sulphide L; as in solution, and has exhibited no serious corrosive action. These uses indicated that aluminum tanks might be equally effective in counteracting hydrogen sulphide corrosion. Consequently, in the spring of 1928, an all-aluminum stock tank of 500 carrels capacity and a "composite" tank of equal capacity, having a steel bottom and bottom ring and an aluminum top and top ring, were placed in service on the State-Lassiter lease of the Gulf Production Co. in Crane County, Tex. These tanks were under observation for one year, the test being sponsored by the Gulf Production Co., the Aluminum Co. of America, and the Parkersburg Rig and Real Co. The results of this preliminary test sustained the belief that aluminum is highly resistant to hydrogen sulphide gas and likewise indicated the type or grade of aluminum which could be most economically used for lease tankage. However, in this preliminary test the tanks were not subjected to contact with the large quantities of highly concentrated brines such as often are associated and produced with crude oil. Therefore, it was suggested by representatives of the Aluminum Co. that additional tests be made to include production conditions in which large quantities of brine would be handled, for pact experience had known that aluminum often is susceptible to the corrosive action of brines.]

Jan 1, 1931

By Oliver Bowles

Limestone is the most widely used of all racks and is essential to a great many industries, including tae building trades, highway construction, metallurgy, agriculture, end many chemical and manufacturing enterprises. It occurs in some form in every State and is produced in thousands of quarries. Production in 1930 exceeded 134,000,000 tons. It has more numerous and more diversified uses than any other rock. This paper is designed to furnish general information on the various branches of limestone quarrying and their economic importance. Brief reference is made to dimension stone, and a more complete discussion follows of the uses, requisite qualities, quarry methods, grid processes of preparation of crushed and broken limestone. Footnote references serve to guide the reader to more detailed information.

Jan 1, 1933

By M. J. Beus

Researchers at the U.S. Bureau of Mines have developed personal-computer-based data acquisition, instrumentation, and mine visualization and modeling techniques to evaluate a mine accessway in a deep hard-rock mine in northern Idaho. These techniques were applied to a mine shaft in a large silver mine that has been in operation for many years. A very deep, rectangular, timber-supported shaft extending to depths exceeding 2.3 km (7,500 ft) had been deforming continuously as a result of nearby mining, resulting in operational problems. Preliminary visual observations and rock and support monitoring confirmed that severe diagonal distortion was occurring. Extensive field measurements and data analysis confirmed initial observations, provided insights into the cause of deformation, and defined a general approach to structural modeling. Computer analysis of the problem was initiated by developing a three-dimensional model of the terrain. This represented a volume of rock approximately 80 km3 (40 x 1010 ft3) and an area on the surface surrounding the mine 9 km2 (3 square miles). Based on this model, a three-dimensional, finite- element analysis was conducted to establish boundary conditions for sequentially more detailed two- and three-dimensional submodels of the shaft area. Results from the computer study are being used to develop new approaches to mine design and to provide design guidelines for deep mine accessways subject to severe rock-mass loading conditions.

Jan 1, 2010

By Jos. R. Guiteras

This paper describes the pumping operations at the Ajax, Cresson, and Vindicator dines in the Cripple Creek mining district of Colorado during the summer of 1936. At that time the three mines wore pumping 6,500 gallons of water per minute into the Roosevelt drainage tunnel. Cripple Creek is the most important gold district in the State; it has yielded gold valued at over $365,000,000. The mines engaged in pumping are among the largest producing properties in the district. ACKNOWLEDGMENTS The author wishes to acknowledge the friendly cooperation of mine officials at the properties visited. At the. Ajax mine information was courteously given by Clayton Kissel, mine superintendent, and his staff; R. Y. Roby contributed the drawings. For information on the Cresson mine, thanks are expressed to Al H. Bebee, mine superintendent, and his staff, especially to Guy Rorabaugh, master mechanic, and to engineer Carlton. At the Vindicator mine, J. S. Anderson; mine superintendent, and Robert Welch, master mechanic, assisted; the latter furnished most of the information about that mine. Acknowledgment is also made of the cooperation of M. H. Salsbury, engineer at the Portland mine, who supplied technical data on the Roosevelt drainage tunnel.

Jan 1, 1937

By Jos. R. Guiteras

This paper is one of a series describing; mining and milling methods and costs being published by the Bureau of Mines. It deals with the mineral resources of western South Dakota and describes the mining and milling of tantalite and associated amblygonite by the Black Hills Tin Co. and the Fansteel Mining Corporation. ACKNOWLEDMENTS Acknowledgment is made to Earl C. Schultz and Arthur I. Johnson, respectively superintendent and engineer for both the Black Hills Tin Co. and the Fansteel Mining Corporation, who contributed the information on mining and milling operations.

Jan 1, 1939

By R. L. Crosby

The Bureau of Mines investigated alloys of copper with 2, 3, and 4 vol pct alumina and with 2 vol pct yttria. Alloys were prepared by a coprecipitation process and were fabricated by pressing and sintering of powders, extrusion, and swaging. Tensile properties at room and elevated temperatures, stress-rupture strength, electrical conductivity, and density were measured. The superiority in elevated temperature strength of dispersion-strengthened copper to OFHC copper was confirmed. Increasing the oxide content from 2 to 4 vol pct produced only a small improvement in strength properties and decreased the electrical conductivity. The 3 vol pet alumina alloy had the best overall combination of properties.

Jan 1, 1969

By L. D. Wyant

That natural gas-gasoline can be used to advantage as a refrigerant is suggested by the fact that the "make" tanks and other parts of the equipment of gasoline plants frequently become coated with frost. The experiments reported in this paper confirm this assumption and indicate that volatile gasoline can be use used to advantage in many refrigerating plants. The Bureau of Mines is making a study of wax distillates in order to find out why satisfactory lubricating oils and waxes can be made easily from certain crude oils and only with difficulty from others. In the commercial distillation of crude petroleum it is customary to separate the distillates into the following groups: (A) Gasolines and naphthas, (B) Kerosenes, (C) Gas oil, and (D) Wax distillate (consisting mostly of light lubricating oil together with small amounts of paraffin Wax).

Jan 1, 1923