Search Documents

By G. L. Oldright, Virgil Miller

"This paper is the tenth 4 of a series on smelting in the lead blast furnace, and the fifth 5 on modifications brought about by the introduction of richer charges.ACKNOWLEDGMENTSAll of the data on handling rich charges in lead smelting given in this recent set of five articles describing the results of a cooperative study by the United States Bureau of Mines and the University of Utah were obtained through the courtesy and with the cooperation of the staff of the Bunker Hill & Sullivan Mining & Concentrating Co. at Kellogg, Idaho. The authors acknowledge with appreciation the assistance given by Stanly A. Easton, vice.-president and general manager, F. M. Smith, smelter director, and A. F. Beasley, smelter superintendent, whose generosity, sympathy, and assistance made it possible to obtain this information for the mining industry.GENERAL DISCUSSIONWhen the charge has been dropped into the lead blast furnace, it is out of control of the operator to the extent that, whatever the material is, it must practically all be melted and run out of the blast furnace. The necessary uniformity of mixture to produce slags of regular composition and the choice of the slag—forming ingredients and products to be formed can be made only before the charge to dropped.It was found (R.I. 3096) at Kellogg, where the charge is mostly sinter, that the ratio of the slag—forming ingredients taken from each tuyere was nearly constant, in contrast to the irregular composition of slags taken similarly from a furnace whose charge consisted of ingredients differing greatly in chemical and physical nature, including size. If the charge consists almost entirely of sinter, the blast furnace should then operate more uniformly."

Aug 1, 1932

By N. Malakondaiah

Several growth chamber and laboratory experiments were conducted to study the germination behavior of plant species on mine spoils and plant growth responses to nutrients on spoils and topsoils. Experiments were conducted to study the germination potential of some native and introduced species under various conditions. The seeds of green needlegrass, side oats grama, thickspike wheatgrass, crested wheatgrass, birdsfoot trefoil and emerald crownvetch were less tolerant, whereas those of alkali sacaton. durar hard fescue, slender wheatgrass, yellow sweetclover and alfalfa were most tolerant to the sodic mine spoil conditions. Addition of leonardite improved the germination potential of some of the poor genninators. Slender wheatgrass and yellow sweetclover were used as test plants to study the fertility status and productivity potential of stockpiled topsoils and spoils collected from Center. Glenharold and South Beulah of North Dakota. The topsoils were neither saline nor sodic but low in N and P. The spoils were neutral to alkaline with SAIL of 12-32, EC of 1.8-5.5 mmhos/cm, Olsen&apos;s P< µ4g/g, and total N <0.07%. Application of N and P together to the topsoils increased the yield of wheatgrass and sweetclover by 88% and 70% of their respective maximum yields, whereas near maximum yields were obtained for both the species by the same treatments to the spoils. The average yields on topsoils were higher than the yields on spoils. The concentrations of major nutrients were higher in plants grown on topsoil, whereas the opposite was true with the concentrations of Mn, Zn, and Cu. Growth chamber experiments were also conducted to study the growth responses of alfalfa, oats and slender wheat grass by the application of Mn and Zn to a sodic coal mine spoil which was previously used for pot culture experiments. Significant growth responses to Mn and Zn were observed in alfalfa but not in oats or slender wheatgrass. Fertilizing the spoil with Mn along with NPK increased the yield of alfalfa to 85% and with Mn + Zn to 99%. Growth responses and plant composition results of this study confirm that the application of major nutrients to spoils can accentuate Zn and Mn deficiencies in some plants.

Jan 1, 1982

By J. G. Donaldson

Optimum conditions are given for chloridizing pyrite, marcasite, chalcopyrite, arsenopyrite, stibnite, and covellite with chlorine gas. The formation of metal chlorides is affected by the time and temperature of chloridizing, and by particle size of the sample. Chloridizing data also are given for chemically precipitated antimony (III) sulfide and copper (II) sulfide.

Jan 1, 1962

By Annie G. Smelley

The Bureau of Mines is testing a dewatering technique for phosphatic clay waste that will recover a portion of the water lost using conventional waste disposal methods and produce solids suitable for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen. In field tests conducted in northern Florida, clay wastes containing a nominal 2.5 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO--treated material will dewater to 30 pct solids in 140 days. Pretreatment of phosphatic clay waste with lime and H202 was shown to improve the dewatering technique for problem clay wastes.

Jan 1, 1985

This article updates the status of fatalities occurring in both coal and metal/nonmetal mines from January through December of 2001. Based on preliminary accident reports, as of December 31, 2001, seventy-two fatalities have occurred at coal and metal/ nonmetal mining operations. During this period, forty-two fatalities occurred at coal operations and thirty fatalities occurred at metal/nonmetal operations. Ignition or explosion of gas or dust and fall of roof were the most frequent accident classifications in coal and powered haulage fatalities were the most frequent accident classification in metal/nonmetal.

Jan 1, 2002

By W. R. K. Wu

Results of linear correlations of two to four variables by the least-squares method are presented. The variables include 63 parameters representing coal composition, coal plasticity, and coke strength. The composition parameters are on chemical analyses; the plasticity parameters, on three plastometer and dilatometer tests and four miscellaneous tests; and the coke-strength parameters, on three ASTM indices. Seventy-two to eighty-four plastic coals were used in the plasticity and carbonization tests, which together form the basis of this report; 43 nonplastic or weakly plastic coals were used in the coal-band studies. Plots of relations between volatile matter, carbon, and oxygen contents of 1,860 U.S. coals and the 84 coals used are shown. Similar plots between volatile matter and hydrogen or atomic H/C of the 84 coals are also included. Significances of regression coefficient signs for coal composition parameters in the significant correlations found are discussed. Based on these significances, the following relations are shown: (a) coke strength versus average aromaticity, or mineral matter content, of the parent coal; (b) characteristic temperatures of the plastometer and dilatometers, the free-swelling index, or the Gray-King type versus average hydroaromaticity of the coal; and (c) nontemperature parameters of the plastometer and dilatometers versus the physical properties of a certain group of compounds from thermal decomposition of coal. Similarly, significances between the positions of coals in the coal band and the aforementioned relations are also discussed. A structural theory of coal plasticity is proposed. Applications of the correlation results are discussed. Composition parameters, such as carbon, atomic H/C, and calorific value may be used as a basis for selecting coking coals for stronger coke. Plasticity parameters, such as the end temperatures of the plastometer and dilatometers and the free-swelling index, may be used for the same purpose. Based on the best correlations found, coke-strength indices may be estimated to within 4 to 8 units of the observed values; the end temperatures of the plastometer and dilatometer tests, 5° to 10° C.; and the free-swelling index, within 1 unit. Accuracies of all these estimated values are examined, based on the experimental errors of the data involved. Finally, estimations of plasticity parameters from one test with those from others are shown.

Jan 1, 1971

By George J. Conroy

This Bureau of Mines report summarizes the results of a study of mine inspection records covering 2,200 mining installations over a 3-year period ending December 1974. Tables show the relative frequency of violations of certain provisions of the Coal Mine Health and Safety Act of 1969 in particular areas of concern, such as circuit breakers, grounding, and permissibility. Examples of past use of the data and analyses are presented.

Jan 1, 1976

By R. W. Stahl

An emergency is defined as an unforeseen combination of circumstances that calls for immediate action. When applied to a coal mine, an emergency may call for prompt removal of the men to the surface through travelways other than the haulageway or intake airways, which are generally contaminated with irrespirable air as a result of an explosion or fire. Therefore, maintenance of adequate and travelable escapeways from all working areas of a mine is vitally important insurance against disaster. Several mine disasters could have been avoided if well-defined escape routes had been provided and made known to all mine employees. Such occurrences, unnecessary as they generally are, unfairly indict the industry when only a small segment thereof is involved. As a result of a rather recent disaster, which might not have happened if good escape routes had been provided, the Bureau of Mines decided to delve into the escape procedure to determine (1) what is being done in the industry and (2) what might be done at reasonable cost.

Jan 1, 1962

By G. R. Fitterer

In the manufacture of steel by any process the refining period involves the partial elimination of the metalloids carbon, manganese, phosphorus, and silicon, by virtue of their reactions with ferrous oxide. At the end of this refining stage the metal consists chiefly of iron in which small amounts of these materials are dissolved. Unless some deoxidizer is added to the steel at this time, the reaction between carbon and ferrous oxide will continue with such force that it is impossible to form sound steal in the ingot molds. Instead, the product will exhibit a marked porosity due to the formation and trapping of carbon monoxide-the product of the reaction mentioned. However, if deoxidizers are added, steel may be obtained which is dense and free from gas bubbles. At the same time the deoxidation products will remain in the steal as impurities. For example, silicon additions form Si02 or combinations of Si02 and FeO. Additions of manganese form deoxidation products consisting of various proportions of MnO and FeO. It is also quite obvious that simultaneous additions of manganese and silicon will form oxide combinations either in the binary system MnO-SiO2 or in the ternary system FeO-MnO-SiO2. Work at the Pittsburgh Experiment Station of the United States Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board, involved the study of such deoxidizing reactions and their products. In this connection considerable information is necessary concerning FeO, MeO, Si02, and Al 203, and their various combinations. Some of the most needed data are the melting points of all of these materials. At the outset of this work ordinary methods of melting point determinations were found to be inadequate for various reasons, and the procedure finally selected involved the use of the micropyrometer with occasional corroboration by quenching methods, The reasons for this selection, together with a description of the apparatus, are given in the following pages.

Jan 1, 1932

By Verne E. Hooker

Stress-relief techniques and instrumentation have been developed through many years of research in the Federal Bureau of Mines and successfully used to determine the in situ state of stress in rock. This paper describes the drilling equipment and accessories for use with the Federal Bureau of Mines three-component deformation borehole gage. Operation and calibration procedures for the deformation gage are discussed in detail. Site selection and overcoring procedures are included to provide a complete working knowledge for surface or underground applications.

Jan 1, 1974

By H. William Zeller, T. E. Westpha1

The U.S. Bureau of Mimes evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pct, depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine&apos;s combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O, but it increased CO, and NO,. The increase in NO,, of about 12 pct, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 1992

By George A. Morgan

Output of minerals was insignificant in 1981 and made a negligible contribution to the gross national product (GNP), estimated at $1.2 billion.2 Agriculture accounted for 40% of CNP and manufacturing accounted for 10%. The chief source of income was indirect taxes levied on traffic through the Port of Cotonou, an entrepôt. Trade statistics for Benin were incomplete and dated. Major trading partners were France and other members of the European Communities. Benin was a member of the West African Monetary Union and as such must coordinate its foreign currency, reserves, interest rate structure, and fund transfer with other member countries. Its currency, the Communauté Financière Africaine franc (CFAF), was fixed to the French franc.

Jan 1, 1983

By Z. J. Fink

Ultraviolet-visible and infrared emission spectra from propagating methane-coal-dust-inhibitor mixtures have been obtained in a 0.2-by 0.2¬by 5.3-m vertical duct over a range of flame speeds from 2 to 100 m/sec. Results serve as a basis for the design and evaluation of thermal radiation detectors for triggered barriers that suppress ongoing mine explosions. Of particular significance is the large continua superimposed on the methane-air spectra when small amounts of coal dust are present and the variation of emissivity with infrared (IR) wavelength in dust flames. In conjunction with the spectral measurements, studies of flame speed, particle size, gas sampling plus thermodynamics, and dust sampling are presented and discussed in order to gain insight into the more fundamental aspects of propagating explosions. Sampling results have shown that only a near-stoichiometric amount of dust is consumed in the flames studied even though initial concentrations are five times stoichiometric. Difficulty in propagating coal-dust inhibitor flames of realistic mine characteristics in a cold-walled laboratory duct has been encountered. A simplified analysis of the flame zone utilizing spectral and sampling results indicates that the stability of slowly propagating flames is more dependent upon thermal radiation than upon convection losses to the walls. It is predicted that thermal radiation losses will make any measurements of coal dust burning velocities, "quenching diameters," or flammability limits more apparatus dependent than those corresponding to gaseous fuels.

Jan 1, 1974

By William N. Hale

This Bureau of Mines report gives a detailed study of water usage in the Montana mineral industries, along with projections for the future. The mineral industry of Montana in 1963 used 36.5 billion gallons of new water, and reused or recirculated an additional 53.5 billion gallons for a total water requirement or usage of 90 billion gallons. The petroleum industry was the major water user, followed by the copper and zinc industries. Many mineral industry operators provide their own water, and new water is withdrawn largely from surface sources. At present, sufficient water is available in rivers, streams, and reservoirs in Montana; however, shortages do exist locally near mineral industry operations using large quantities of water. Some is supplied from sources up to 44 miles distant. New water withdrawn by the State of Montana mineral industry is expected to increase from 36.5 billion gallons in 1963 to 51.1 billion gallons by the year 2000. The total-water requirement is expected to more than double, or reach 182 billion gallons by the year 2000.

Jan 1, 1966

By William N. Hale

This Bureau of Mines report gives a detailed study of water usage in the Montana mineral industries, along with projections for the future. The mineral industry of Montana in 1963 used 36.5 billion gallons of new water, and reused or recirculated an additional 53.5 billion gallons for a total water requirement or usage of 90 billion gallons. The petroleum industry was the major water user, followed by the copper and zinc industries. Many mineral industry operators provide their own water, and new water is withdrawn largely from surface sources. At present, sufficient water is available in rivers, streams, and reservoirs in Montana; however, shortages do exist locally near mineral industry operations using large quantities of water. Some is supplied from sources up to 44 miles distant. New water withdrawn by the State of Montana mineral industry is expected to increase from 36.5 billion gallons in 1963 to 51.1 billion gallons by the year 2000. The total-water requirement is expected to more than double, or reach 182 billion gallons by the year 2000.

Jan 1, 1966

By Victor Erickson

ECONOMIC recovery, which began in 1958, carried through into 1959 but was somewhat retarded by the 116-day steel strike beginning in July 1959. Recovery and economic growth increased production and consumption of mineral fuels 3 percent above 1958. The increase was accomplished despite a drop of 26 percent in coal exports. Prices remained constant during the year so that the value of production and consumption also increased 3 percent over 1958. Stocks in the hands of producers at yearend were little changed from the supply at the beginning of the year. Employment in the field of mineral fuels decreased 6.4 percent from 1958. Average hourly earnings were up 7 percent, and average hours worked were up 5 percent, with the result that weekly earnings gained 11.8 percent. Internal freight rates were relatively constant, but ocean tanker rates declined both in 1958 and 1959 from the high rates charged during the Suez crisis. The index of major input expenses decreased for anthracite, held constant for bituminous coal, and increased for petroleum. The index of labor cost per dollar of product and per ton of product declined again in 1959 to a new low in anthracite and bituminous-coal mining industries.

Jan 1, 1960

By J. D. Noll, S. E. Mischler

Measurement and sampling of diesel particulate matter in mine air presents a challenge due to the complexity of the diesel aerosol. The results of a series of tests carried out by the National Institute for Occupation Safety and Health, Pittsburgh Research Laboratory, in an underground mine were used to evaluate several measurement methods that are currently used to characterize particulate matter emitted by diesel-powered equipment. This paper presents an overview of these techniques and examples of the results along with a discussion of the advantages and information gained by each technique. The measurement methods discussed include particle size measurements using a scanning mobility particle sizer, total particulate matter measurements using a tapered elemental oscillating microbalance, a size selective sampling method for workplace and personal exposure assessment and a size-selective high volume sampling method for carbon analysis.

By Kathleen M. Kowalski-Trako?er

National Institute for Occupational Safety and Health re­searchers conducted a study to investigate the human response issues related to wearing a self-contained self-rescuer (SCSR). The goal was to develop training to educate miners on what they could expect from their units during an escape. Subjects included miners who had experience wearing SCSRs, manu­facturers, and researchers. Results identified nine key areas of concern: (1) starting the unit, (2) unit heat, (3) induction of coughing, (4) unit taste, (5) difficulty in breathing while wearing the unit, (6) quality of the air supplied, (7) nose clips, (8) goggles, and (9) the behavior of the breathing bag. In addition, researchers reviewed the literature on human response under duress. This article describes the expectations training program, which comprises the findings of the SCSR study and what is known about the normal human response in an emergency. The authors present background on SCSRs and the SCSR switchover procedure mandated in the recent federal Mine Improvement and New Emergency Response Act of 2006, which provided the impetus for the expectations training. Keywords disaster, escape, mining, self-contained self-rescuer, training

Jan 1, 2008

By Thomas M. Barczak

Roof support systems are necessary to provide stable mine openings and much research has been conducted to design a variety of roof support systems that will function in various manners to ensure that stable ground conditions are achieved. Despite these advancements in technology, mistakes continue to be made in the evaluation and/or installation that significantly degrade the support capability or lead to erroneous determinations of support expectations. The purpose of this paper is to discuss misconceptions about how roof supports perform and factors that impact their performance. The goal is to present practical information that will assist mine operators and engineers in selecting, installing, and evaluating roof support systems properly, and help them to avoid mistakes that can lead to erroneous expectations and potentially catastrophic results that may lead to roof falls. The paper is limited to a discussion of secondary roof support systems and powered roof supports such as longwall shields.

By L. Nahai

An important objective of the Australian Government&apos;s policies on resources development is to encourage further processing of raw materials domestically, to the extent that this is economically feasible and consistent with sound industrial development. This Bureau of Mines report examines the extent to which Australia is able to pursue this policy in terms of its own competitive advantages and the implications of such a policy for the United States. Such factors as the impact of other competing producers and their advantages, expected world demand, and infrastructural problem--which may limit pursuit of this policy to the fullest extent--are discussed. After a broad review of the re-source, economic, social, and environmental factors, the perspective for increased processing is examined for a number of mineral commodities.

Jan 1, 1982