Search Documents

By David C. Peters, Robert S. Crosson

A method of error analysis has been applied to the location technique of non-linear least squares iterative inversion in order to evaluate the resolving power of several seismic array configurations with various assumed earth models and errors and inaccuracies in arrival times. The results obtained demonstrate that lateral accuracies of location are improved significantly when the depth of the miner is known. Lateral location to within 100 feet appears achievable in many instances. If it is possible to refine earth models significantly beyond what has normally been assumed in this work by the use of on-site data, or if the mine is shallow (300 feet or less), accuracies of-about 30 feet or so may be attainable. Inaccuracies in earth models of about 5% are found to contribute much more heavily to these location inaccuracies than errors of a few milliseconds in picking arrival times; however, arrival time errors of 15-20 ms or above will dominate these model inaccuracies. The expected accuracy of location is found to fall off very rapidly as the miner moves outside the array. The strength of this effect depends markedly upon the geometry of the array configuration and can be reduced by careful design. Also, as the size of the array is increased, expected location errors within the array are not altered much, but continue to match the error associated with the smaller array over a larger area (assuming that all stations can still pick up the miner's signals). Better location accuracy, especially with respect to depth control is achievable in an earth where the velocity is depth-dependent (increasing with depth) than in one which is homogeneous. This is an advantage since the

Jan 1, 1974

By H. W. St. Clair

This study was undertaken to provide a more adequate knowledge of the chemistry of the sulfide volatilization process for recovery of tin from low-grade Bolivian ores. The investigation was partly supported by the Department of State under its program for scientific cooperation with South American republics. The results of this investigation demonstrate the conditions under which cassiterite (Sn02) may be converted to stannous sulfide by reaction with pyrite or sulfur vapor, Quantitative data are given on the rate of sulfidization and on the vapor pressure of stannous sulfide.

Jan 1, 1954

By W. J. Crawford, P. M. Gruzensky

"Several experiments have been carried out in efforts to evaluate qualitatively a variety of electrolytes for refining bismuth. Most extensive work was done with the basic tartrate, hydrochloric acid, and hydrofluosilicic acid electrolytes. Deposits that are smooth and adherent can be obtained from these three electrolytes if low cathode current densities are employed. All three electrolytes were effective in purifying crude bismuth considerably, with additional purification indicated in each instance by a reelectrolysis step.With the basic tartrate electrolyte best results were obtained when the electrolyte was at 40° C. and contained at least 100 grams of bismuth per liter. An apparent disadvantage was depletion of bismuth from this electrolyte, causing the deposits to become spongy and nonadherent.The hydrochloric acid electrolyte had the greatest tendency to yield rough, dendritic deposits. Best deposits were obtained at cathode-current densities below 2 amperes per square decimeter. A small amount of glycerin helped to produce a smoother deposit, and adding sulfuric acid or methyl sulfuric acid retarded the deposition of impurities. Very good results were obtained in electrowinning bismuth from a bismuth trichloride-hydrochloric acid electrolyte.Smooth and adherent deposits were obtained from a hydrofluosilicic acid electrolyte, with very good refining as regards lead and silver impurities; however, higher reagent costs and slow decomposition of the electrolyte have discouraged its use.INTRODUCTIONMethods of recovering bismuth from ores and byproducts were underdeveloped for many years because of the limited uses for bismuth, the pharmaceutical industry being the chief consumer. In the past decade or so additional uses for bismuth, particularly in the metallurgical field, have brought about increased demand for the metal with the result that bismuth is being recovered from byproducts that were once discarded. In addition to such uses as low-melting alloys, solders, bearings, die setting, etc., some interest has been indicated in bismuth as a possible coolant for nuclear reactors. The advent of ductile bismuth and bismuth-alloy thermocouple wire has contributed greatly to temperature measurement, particularly in the below-zero range."

Jan 1, 1956

By J. R. Ross

Techniques for recovering scandium from uranium plant iron sludges and from wolframite concentrates are described. The best procedure found comprised (1) dissolution with sulfuric acid, (2) preliminary concentration by solvent extraction with a primary alkyl amine, (3) further enrichment and purification by a combination of ion exchange, solvent extraction, chemical precipitation, and calcination. Recovery of scandium from these raw materials, which contained 0.058 and 0.14 percent scandium, ranged from 83 to 90 percent in products analyzing 99.6 to 99.9 percent scandium oxide.

Jan 1, 1965

By Russell R. Trengove

Bureau of Mines exploration at the property of the Tulare County Tungsten Mines was by core drilling from the surface from May 16, 1950, to July 13, 1950. The property is in the western foothills of the Sierra Nevada Range, 18 miles northeast of Lindsay, Calif. It has been in almost continuous production since 1942 and has produced 40,831 units of tungsten trioxide (W03) with a grade of approximately 67 percent. The work performed comprised a study of the geology, mapping the area, sampling the outcrops, and diamond drilling the area adjacent to the mine workings. Ten holes were drilled for a total of 1,824 feet. Ore reserves were found to be confined to tactite zones in a surface area approximately 250 by 400 feet and extending downward about 350 feet.

Jan 1, 1956

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Ti and Zn-1.0 wt pct Cu-Ti alloys containing up to 0.36 wt pct Ti. Finish rolling was at varied temperatures to total reductions as high as 92 pct. Alloy properties are very sensitive to various combinations of composition, rolling temperature, and reduction. Properly rolled Zn-1.0 Cu-Ti alloys are superior in strength to Zn-Ti alloys. Conditions are described that lead to best tensile properties. Creep resistance for Zn-Ti alloys decreases with increased rolling temperature when finish rolled to 92-pct total reduction: but not when finish rolled to 33- or 67-pct reduction. Creep resistance for 7n-1.0 Cu-Ti alloys improves with increased rolling temperature to about 480° F. Heavily cold-rolled Zn-1.0 Cu-Ti alloys have fine grain sizes and poor hardness, tensile, and creep properties, but high ductility. Thermal expansivity is markedly affected by the copper addition. Data show the anisotropy of tensile, creep, and thermal expansivity properties. Large idiomorphic crystallites of TiZn15 appear in both Zn-Ti and Zn-Cu-Ti alloys when more than about 0.2 pct Ti is present. A new Zn-Cu-Ti intermediate phase was also identified. Empirical equations are presented relating creep rates with major process variables.

Jan 1, 1971

By J. W. Paul

This circular is one of a series of reports on coal mining methods and cost s which are being prepared by the U. S. Bureau of Mines for the purpose of making available to those interested in the industry a knowledge of the mining methods employed in mines where mechanical and hand loading is practiced and the cost data on the several operations pertaining to the removal of coal from the working faces and its transportation to the tipple for loading into railroad cars. The methods employed are influenced by the natural local conditions with respect to the thickness and character of the coal beds and the overlying strata, the means employed for roof support and its control, and the disadvantages incident to the development of mines in thin coal beds.

Jan 1, 1929

By T. H. Jeffers

The Bureau of Mines conducted laboratory tests to devise a procedure for extracting copper from low-grade discarded mill tailings. A solid extractant consisting of an organic solvent extraction reagent adsorbed on granular activated carbon was investigated and proved to be satisfactory for extracting copper directly from leach pulps. When this material was used in a cyclic leaching, stripping, and electrowinning pro-cess, 95 pct of the acid-soluble copper was recovered from oxidized mill tailings. The weathered tailings contained 0.24 pct Cu (total) and 0.20 pct acid-soluble Cu. The copper was recovered as cathodes containing, in parts per million, 1.6 Pb, 3.6 Fe, 0.5 Sb, 1.5 AI, 1.9 Mn, and <1 Mg.

Jan 1, 1985

By M. P. Youker

USE OF LOW-PRESSURE GAS BURNERS IN OIL- FIELD BOILERS

Feb 1, 1922

By John A. Organiscak

The Bureau of Mines conducted a survey of eight shearer longwall operations to identify factors that affect respirable dust generation from longwall roof supports. The longwalls surveyed were in coal seams located in different geographic regions of the United States. Data were collected on mining (geologic) conditions, support design, operational characteristics, and amount of respirable dust generated from roof supports. Analysis indicated that mining conditions are the main factors that affect the generation of dust during roof support movement. Both roof strength and depth of cover above the coal seam showed relationships with the amount of support dust generated. Several practices are currently employed to effectively control roof support dust; however, some of these controls are limited. More research and development is needed to improve dust control technology for longwall roof supports.

Jan 1, 1985

By William R. Roy

Seven coal-related waste samples (mining, cleaning, and gasification) were characterized chemically and mineralogically. Laboratory extracts of each sample, using a variety of different extraction methods, were used in both acute and chronic bioassays. A coal slurry sample (coarse fraction) and two coal cleaning refuse samples were chemically and mineralogically similar, and generated acidic water-waste systems, both in the laboratory and in the field. Acidic laboratory extracts and field samples of acid mine drainage in the area where the solid samples were collected, tended to be in equilibrium with some type of CaSO4 phase and with maghemite. The chemical composition of the extracts was sensitive to the method used to generate the extracts, but generally had the same prevalent chemical character as the field samples. The acidic wastes contain appreciable quantities of soluble Al, Mn, Ni, SO4, and Zn as indicated by both laboratory extraction and field data. Long-term extractions suggest that some constituents (Al, Fe, SO4) continued to be released by the acidic wastes after 22 weeks with no apparent associated change in pH. Two mine spoil samples, essentially shale, tended to generate water-waste systems that were neutral in pH and consequently released lower quantities tit potential pollutants than the acid wastes. The gasification residue was compositionally similar to coal-fired power plant slag and fly ash and generated moderately alkaline extracts with low concentration of soluble potentially toxic constituents. All of the solid wastes contained a variety of organic compounds, many of which are on the EPA Priority Pollutant List. However, these compounds were essentially insoluble in aqueous media. Each extract was tested for acute toxicity with tour species of freshwater aquatic organisms; green sunfish (Lepomis cyanellus), fathead minnow (Pimephales promelas), a crustacean (Daphnia magna), and a snail (Physa anatina). The extracts of the two mine spoil samples and of the gasification residue were not toxic to any of the organisms while the extracts from the acidic refuse and slurry samples were acutely toxic to all of the organisms. For all cases, pH was significantly correlated to mortality while Al, Fe, Mn, Ni, and Zn were significantly correlated to mortality in specific instances. Data from 96-hour LC-50 determinations showed that dilutions up to 1:1000 were necessary to eliminate mortality. The most toxic extracts were those with the lowest pH which necessitated the largest amounts of dilution to eliminate mortality. Chronic bioassays with the same test organisms were investigated with leachate samples from a relatively unweathered refuse sample and an older, more weathered refuse sample. The unweathered refuse sample generated a leachate that was acutely toxic while the leachate from the weathered refuse sample was not acutely toxic. No detrimental chronic effects were noted in organisms exposed to dilutions of the non-toxic leachate while low concentrations of the acutely toxic leachate produced lower hatchability for the Lepomis cyanellus and Pimephales promelas eggs, increased mortality with chronic exposure for Lepomis cyanellus, Daphnia, Physa, and reduced weight gain for Physa. Dilutions of a toxic, high-Fe leachate resulted in the precipitation of ferric hydroxide that was implicated as the major causative factor accounting for the physical and physiological toxic effects exhibited by all of the test organisms in these acutely sublethal concentrations. The toxicity of this leachate demonstrates the potential effects that these types of wastes can have on the aquatic ecosystem if they enter a receiving water in a natural setting.

Jan 1, 1984

By A. L. Engel

This report is a compilation of results of preliminary concentration tests of seven manganese-ore samples. Six of the seven samples were submitted through the Mining Division, and 1 from Mexico was submitted by H. A. Doerner, formerly chief metallurgist, Region III. These investigations were made to assist development of mineral resources and particularly to aid economical exploitation of marginal or complex ores, from which strategic or critical minerals may be recovered.

Jan 1, 1953

By R. E. Cumings

The Bureau of Mines made electrorefining tests in inert-atmosphere, molten salt cells to develop methods for the preparation of high-purity molybdenum. Seven of the electrolytes investigated were suitable for the preparation of refined metal. The electrolytes were composed of molybdenum chloride in alkali chlorides or mixtures of alkali and alkaline-earth chlorides. An electrolyte composed of potassium chloride and potassium hexachloro-molybdate was selected for a larger scale, more detailed study on the basis of its ease of preparation, its ability to retain the molybdenum salt, and the type of deposits obtained. High-purity molybdenum in the 99.99-percent-purity range was successfully prepared as dense plate up to 80 mils thick and as dendritic crystals. The temperature of electrolysis and the current density were major factors in determining whether plate or dendritic crystals of molybdenum were obtained.

Jan 1, 1966

By John P. Gooch

The solubility of 1,1,2,2-tetrabromoethane (TBE) in water was determined from 1.0° to 97.0° C. The solubility (S) of TBE in grams of solute per 100 grams water was correlated with [S = 1,920.55 [exp (40292L7 11, T2 10 T 737.577 + 9.923962 ] where T is in degrees Kelvin. A thermodynamic analysis conducted on a system consisting of a TBE phase and a water phase in equilibrium with a vapor phase led to the calculation of the activity coefficient, vapor-liquid equilibrium distribution coefficient, relative volatility, and heat of mixing for saturated solutions of TBE in water. Data required for these calculations were the solubility of TBE in water and the vapor pressures of TBE and water as a function of temperature.

Jan 1, 1972

By T. Kessler

Spark-source mass spectrometry has been used to determine the amounts of minor and trace elements in coal particles of various sizes, including the respirable range (<5 microns). Fifty-six elements ranging in concentration from 0.1 ppm wt to 5,000 ppm wt have been determined. The investigation of coal and coal ash has shown that the organic material in coal does not interfere with the spark-source determination of the various elements.

Jan 1, 1971

By John Furness Park

This paper, which describes the mining methods and practices at the Jarbidge mines of the Elkoro Mines Co., is one of a series of papers being issued by the United States Bureau of Mines on mining methods and costs in various districts throughout the United States. LOCATION AND HISTORY The Elkoro Mines Co.&apos;s property is located at Jarbidge in the northeast corner of the State of Nevada (fig. 1). The camp is 9 miles south of the Idaho line; the nearest railroad point is 70 miles to the northeast at Rogerson, Idaho. A road leading to the south and connecting with Deeth, Nev., is passable during the summer months; the heavy snowfall which generally takes place early in the winter usually closes the road until the first of July.

Jan 1, 1931

By W. F. Dietrich

1. On St. Thomas and St. Croix, and possibly also on St. John, low-quality red-burning clays probably can be developed to provide the major part of the raw materials for structural clay products and earthenware pottery. 2. The potential sales volume for structural clay products is too small to sustain a plant in the Virgin Islands to manufacture such products in competition with Puerto Rico; however, handmade patio tile might be produced successfully. 3. The market for pottery utility wares in the Virgin Islands is too small to justify a plant devoted solely to the production of such wares; but it may be feasible to evolve a diversified community activity to make jugs, pots, casseroles, bowls, charcoal burners, patio tile, and other items.

Jan 1, 1955

By Lung Cheng

Based on earlier tests that showed steel to be much more likely to cause frictional ignition than tungsten carbide, the Bureau of Mines redesigned coal-cutting bits to reduce the hazard of face ignitions. Two bit designs--a mushroom-shaped bit with a conical shank and a dove-tail bit with a rectangular shank--are described, as well as bit wear tests conducted in the laboratory and in an operating coal mine. In laboratory tests, for 1/8-, 1/4-, and 1/2-in-deep cuts and cutting speeds of 280, 500, and 660 ft/min, the mushroom bit had significantly longer tip wear life than the conventional bit; the dovetail bit was also superior to the conventional bit. Results of in-mine tests on the mushroom bit agree well with laboratory results. In-mine tests of the dovetail bit are underway.

Jan 1, 1983

By Edward F. Divers

This Bureau of Mines report describes a new type of scrubber (dust collector) and ventilation system built into the auger support frame (boom) of a Jeffrey 120L continuous mining machine. With this twin scrubber arrangement, one scrubber is mounted into each side of the boom. Each scrubber includes a 2,500-cfm fan, a flooded fibrous-bed scrubber panel, and a water droplet eliminator. The system was designed for minimum size and adds only a few inches to machine height. Exhaust duct design allows flexibility with various airflow configurations to suit both blowing and exhaust fare ventilation systems and brattice distances ranging up to 20 feet. Full-scale tests with exhaust ventilation were conducted at a Mine Safety and Health Administration surface facility at Bruceton, Pa., to determine the scrubbers&apos; methane dilution capability. Several configurations of the twin scrubber-ventilation system produced striking improvements in face methane dilution when compared with conventional systems.

Jan 1, 1981

By J. M. Mutmansky, C. Lee

"IntroductionRecognition of Coal Workers' Pneumoconiosis (CWP) as a major occupational disease has affected various aspects of the coal mining industry in the United States as well as in almost all major coal producing countries, Regulations related to the control of coal mine dust forced mine operators to modify their mining and ventilation practices. As the coal production record of the last 15 years shows, this had both direct and indirect impacts on the productivity and production costs.To identify the causes of CWP, many research efforts have been made throughout the world. Most of these studies were epidemiological in nature, attempting to pinpoint exposure and seam variables that affected the incidence of the disease. Other studies have been oriented toward the elemental and mineralogical composition of the coal dust in the mine atmosphere and in the miners' lungs. These studies indicate that there may exist some relationships between the characteristics of the coal mine dust and the prevalence of the disease. Some of the variables that are thought to affect the occurrence of CWP are the mass of the dust in the working place, the rank of the coal, the existence of certain trace elements, the free silica content of the coal, and the existence of other minerals in the respirable dust. A more complete description of these previous research studies has appeared elsewhere (Mutmansky and Lee, 1984).The behavior of particles in the human lung is known to be governed by their aerodynamic diameter, which is defined as the diameter of a hypothetical spherical particle with unit density that exhibits the same settling velocity as the given particle. Because of this fact, the aerodynamic size distribution of coal mine dust is one of the parameters to be determined along with the other physical, elemental, and mineralogical characteristics. The objective of this paper is to establish a strategy for providing coal mine respirable dust samples for characterization purposes using instruments that classify according to the aerodynamic diameter. In addition, several findings concerning characterization methods will be presented"

Mar 1, 1989