Search Documents

By P. L. Woolf

An investigation was conducted to evaluate the use of a formcoke as the total fuel in the Bureau of Mines experimental blast furnace. The formcoke performed very satisfactorily, and comparisons made with a metallurgical coke showed that the performance with the formcoke was somewhat superior under the experimental conditions used.

Jan 1, 1966

By W. M. Dressel

The objective of the research reported in this publication of the Federal Bureau of Mines was to devise a mineral dressing procedure that would concentrate zinc silicate minerals from certain deposits in southwestern Missouri. The best flotation results were obtained by batch laboratory flotation using sulfidizing agents and ethoxylated cocoamine. The flotation concentrate contained 70 percent of the zinc at a grade of 47.8 percent. Gravity concentration tests showed that 55 percent of the zinc could be recovered at a grade of 48.3 percent.

Jan 1, 1961

By A. W. Deurbrouck

The Bureau of Mines reviewed available data on the effect of crushing high-sulfur coals for the liberation of impurities in the light of increasingly stringent air pollution regulations. The survey, which provided information on Appalachian region coals only, indicated that such important coal- beds as the Upper and Lower Freeport and the Upper Kittanning show significant sulfur reductions when crushed to 14-mesh top size. For many other coalbeds amenability to sulfur liberation by crushing was indicated, although too few samples were available to draw firm conclusions,

Jan 1, 1966

By A. W. Deurbrouck

The Bureau of Mines reviewed available data on the effect of crushing high-sulfur coals for the liberation of impurities in the light of increasingly stringent air pollution regulations. The survey, which provided information on Appalachian region coals only, indicated that such important coal-beds as the Upper and Lower Freeport and the Upper Kittanning show significant sulfur reductions when crushed to 14-mesh top size. For many other coalbeds amenability to sulfur liberation by crushing was indicated, although too few samples were available to draw firm conclusions,

Jan 1, 1966

By D. E. Redmon

Linear programing provides a mathematical technique by which activities can be planned in such a way that an optimal result is obtained. Routine applications of linear programing require only a knowledge of algebra. However, a complete understanding of the fundamentals of linear programing requires a knowledge of advanced mathematics. The purpose of this publication is clarification of terminology and illustration of applications in comparatively simple mining problems. Two mining situations are considered: Mine stopes from which ore is to be produced at a minimum production cost; also, uranium mines from which ore is transported to one mill, a maximum monetary value is desired. The details of data arrangement for solution by linear programing are described and the solutions are presented. Results of these solutions indicate successful applications of linear programing to mine production scheduling.

Jan 1, 1964

By J. B. Clemmer

Fluorspar is one of the most important nonmetallic minerals and is used extensively in the metallurgical, ceramic, cement, and chemical industries. The steel industry consumes most of it, but as the Mineral is the chief source of fluorine, it is becoming increasingly valuable to the chemical industry in the production of fluorine compounds The development of nontoxic organic fluorides for use as refrigerants in mechanical refrigeration and air-conditioning units illustrates the increasing use of fluorspar in the chemical industry. Most domestic flurospar comes from deposits in the Illinois-Kentucky district, which centers around Rosiclare, Ill. About a dozen companies operate in the district, which comprises parts of Pope and Hardin Counties in southern Illinois and Crittenden, Livingston, and Caldwell Counties in western Kentucky. According to the latest available statistics, this district supplied 1/5,960 short tons of fluorspar in 1937, compared with the total domestic production of 181,230 tons. Imports totaled 37,063 tons.

Jan 1, 1939

By J. B. Clemmer

Fluorspar is one of the most important nonmetallic minerals and is used extensively in the metallurgical, ceramic, cement, and chemical industries. The steel industry consumes most of it, but as the Mineral is the chief source of fluorine, it is becoming increasingly valuable to the chemical industry in the production of fluorine compounds. The development of nontoxic organic fluorides for use as refrigerants in mechanical refrigeration and air-conditioning units illustrates the increasing use of fluorspar in the chemical industry. Most domestic flurospar comes from deposits in the Illinois-Kentucky district, which centers around Rosiclare, Ill. About a dozen companies operate in the district, which comprises parts of Pope and Hardin Counties in southern Illinois and Crittenden, Livingston, and Caldrell Counties in western Kentucky. According to the latest available statistics, this district supplied 165,960 short tons of fluorspar in 1937, compared with the total domestic production of 151,230 tons. Imports totaled 37,063 tons.

Jan 1, 1939

By P. D. Lindahl

[A cost/benefit analysis was conducted by comparing the industry cost to protective structures on low-coal face equipment with the benefits paid for injuries/fatalities considered preventable by the use of these structures. Th industry costs were based on estimates by OEM's and rebuild shops for install protective structures on new and rebuilt face equipment. The accident benefit was based on evaluations performed by the USBM Accident Cost Indicator Model. Industry wide population data were developed on low-coal face equipment and injuries/ fatalities preventable with protective structures. The results of the analysis are to be used as a tool by USBM in determining the feasibility of continuing development of cab and canopy technology for low-coal equipment.]

Jan 1, 1983

By Robert G. Bottge

Hard rock mining has grown in importance in the Yukon Territory during the last 10 years while Alaskan hard rock mining has declined. One asbestos deposit in Alaska is dormant, but an asbestos deposit 55 miles to the east in the Yukon Territory is being mined by the Clinton Mine Div., Cassiar Asbestos Corp., Ltd. In this Bureau of Mines report, the economics of mining in the two locations were derived using the Clinton mine as a model. Both deposits were assumed to be of equal size and mined by similar methods. Conventional open pit mining and processing methods were assumed, and capital and operating costs were derived using flowsheets and standard costing methods. The estimated cost for the mine, mill, and support facilities in Alaska was about 30 percent more expensive than that in the Yukon Territory. The higher labor rates in Alaska were the primary contributor to the higher construction costs; freight rates added only slightly to the total costs. Approximately two-thirds of the additional annual costs of operating in Alaska were for wages and fringe benefits. The price required for the Alaskan asbestos fiber was $356.65 per ton compared with $287.44 for Yukon fiber, plus or minus 20 percent. A 12 percent discounted cash flow rate of return, 100 percent equity financing, and a rapid writeoff of assets were assumed.

Jan 1, 1975

By J. E. Wilson

The Pittsburgh carbonization laboratory of the Bureau of Mines has determined the expansion or contraction of more than 300 coking coals in a modified Bethlehem-type sole-heated expansion tester. Information on the actions of coals or blends of coals when coked is extremely valuable to operators of commercial-scale coke ovens. Coals that expand abnormally or beyond expectations can cause extensive damage to coke ovens and result in costly shutdowns and repairs. Although test results for many of the coals have been given in various Bureau of Mines publications, considerable information was not published. Thus, it is the purpose of this report to furnish coal operators and the coking industry with a current appraisal of the expanding properties of all coals tested by the Bureau before September 1, 1958. These data should be useful in the normal long range planning of coal and coke production and will be essential if the demand for coking coals increases abnormally or when reserves of higher grade coals are depleted.

Jan 1, 1959

By B. J. Dalton

Several relationships between coexisting phases for analytical binary solutions near the critical point are given. These relationships were developed from a consideration of a (G u, P) surface at constant temperature and a (G u, T) surface at constant pressure, where G is the molal Gibbs free energy, u is the concentration of component 1 expressed as a mole fraction, G is the pressure, and T is the temperature. These formulas should facilitate the calculation of some of the quantities useful in making thermodynamic consistency checks on phase equilibria data about the critical point.

Jan 1, 1970

By Gwendolyn D. Hood

The U.S. Bureau of Mines developed a dewatering technique for treating wastewater that was tested on waste slurry from a commercial tile company in Alabama. Raw wastewater samples were pretreated with 10 Ib calcium chloride and 10 lb Wyoming bentonite per 1,000 gal of slurry. After pretreatment, polyethylene oxide (PEO) at dosages varying from 0.05 to 0.20 lb per 1,000 gal was mixed with the waste slurry, forming strong, tough floes that were separated from the clarified water using a trammel. The flocculated slurry was dewatered to a consistency that could be handled for subsequent disposal in a landfill. The clarified water quality was equivalent to that of the company's present treatment system.

Jan 1, 2010

By A. W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds from which samples could be obtained in Webster County, W. Va. In 1964, approximately 825,000 tons of coal was produced in the county, of which 732,000 tons was mechanically cleaned in three preparation plants. The Sewell coal bed accounted for 94 percent of the coal produced. Twelve samples were collected from five coalbeds. Four of the samples would require upgrading to meet metallurgical requirements; two others of just over 8.0 percent ash would require some upgrading. In general the coalbed samples collected in the county were of medium-sulfur and medium-to low-ash content as received or after removal of the sink 1.58-specific-gravity material.

Jan 1, 1966

By Eric R. Bauer

The magnitude and rate of advance of an inmine coal squeeze was deter-mined by measuring roof-to-floor convergence on a regular basis. A dial-gage tube extensometer was used to collect data. Using these measurements) Bureau of Mines employees drew contour maps and graphs to show the direction and rate of squeezing. Information on the rate of squeeze advance was used to determine whether steps should be taken to prevent roof and/or floor movement from closing an entire section of the mine and if alteration of mining plans was necessary to prevent further squeeze development. Data analysis revealed that the squeeze was decelerating; thus there was no need to strengthen support in the areas of the mine that were studied. Mining plans were altered, however, as a result of the findings of this investigation.

Jan 1, 1981

By C. W. Davis

Two general schemes have been used for the determination of gold and silver in material containing considerable quantities of copper ; one is known as the " all fire " method , and the other as the , " combination " , or " wet and dry" method . The all fire crucible method , using an excess charge of litharge , has been found satisfactory when the copper content of an ore is under 6 per cent , ( Loevy , J. , Zur Edelmetallbestimmung in hochprozentigen Kupfererzen : Chem. Ztg . Jarhrg . 35 , 1911 , p . 278 ) , or where the precious metal value is so great that a small sample can be used . In the latter case , silica is added until the copper ratio is sufficiently low . If there is more than 6 per cent of copper in an ore , the lead button obtained from a crucible fusion will require repeated scorification before . it can be cupelled successfully . Rescorification is not only tedious , but also causes a slag loss of precious metals . In combination methods , the copper is dissolved , and the gold and silver in the residue . is determined by fire assay Although some combination methods have given satisfactory results for gold and silver , they are not applicable when an estimation of the platinum metals is required . Since substances containing platinum are frequently high in copper , a study of methods which might be used for the estimation of small quantities of gold , silver , and the platinum metals in such material was considered worth while . The estimation of platinum in ores by fire assay methods has been described in Technical Paper 270 of the bureau; ( Davis , C.W. , The detection and estimation of platinum in ores : U. S. Bureau of Mines Tech . Paper 270 , 1921. ) the present paper , which is supplementary to that report , deals chiefly with the application of combination methods , taking them up to the point where the fire assay is to be applied .

Mar 1, 1921

By F. E. Walker, S. J. Aresco, J. B. Janus

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal , expressed in British thermal units , and the composition as shown by proximate analyses . To these , when required , are added the ash- softening temperature , the free - swelling index , and the Hardgrove grindability index . Under most of these specification contracts the bidders guarantee the quality of the coal , and that guaranteed by the successful bidder becomes the standard of his contract . The deliveries are sampled in accordance with instructions 4/ issued by the Bureau of Mines ; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and , if it is not , a price adjustment is made . Analyses of the delivered coal and tipple samples ( samples collected at mine tipples as coal is being loaded into railroad cars or trucks ) provide valuable data for use in evaluating future bids . In addition , the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal . The Government purchased approximately 5 million tons of coal in fiscal year 1962. In connection with these purchases , the Bureau analyzed 7,114 samples . These are published ( table 1 ) for the use of Government officials and the public . A series of publications has been completed on coal analyses by States or , where production is small in any one State , by groups of adjacent States . In addition to analytical data showing composition and quality of coals of the States , the publications contain brief descriptions

Jan 1, 1963

By Donelson A. Robertson

Literature was searched and cases of alleged water well damage were investigated. Occurrence of ground water in Appalachia is primarily in low yield, fractured, water table aquifers. Four test sites were chosen based on geographic and geologic diversity. Test wells were drilled at each site and base line data on water quality, static water level, and drawdown characteristics were obtained before surface mining commenced. Blast induced ground vibrations were measured at the surface by the wells at levels up to 5.44 inches per second maximum resultant particle velocity. Measurements made at the bottom wells indicated that vibrations were considerably attenuated at depths of 140 to 160 feet. No direct evidence of change in water quality or well performance was produced by blast vibrations, but removal of downslope support by excavation does cause lateral stress relief which permits the water-bearing fractures to become more open. This additional storage capacity causes the static water level to drop and for well-bore permeability to improve. Static water level recovers if sufficient recharge is available and well performance is improved.

Jan 1, 1980

By N. H. Coates

The Bureau of Mines determined average film coefficients of heat transfer for helium flowing through smooth, water-cooled tubes at Reynolds numbers of 5,000 to 25,000, helium inlet temperatures of 1,600° to 2,600° F, average temperature difference across the helium film of 800° to 1,300° F, and heat flux to 215,000 Btu/(hr)(sq ft). Since helium was the only gas used, the ranges of values for physical properties of the fluid are limited--thermal conductivity from 0.15 to 0.20 Btu/(hr)(sq ft)(O F/ft), viscosity from 0.082 to 0.104 lb/(ft)(hr), and Prandtl number from 0.63 to 0.68. Four equations, three of them dimensionless, correlate these coefficients with other properties of the helium--bulk temperature, film temperature, dimensionless parameters based on temperature, and the ratio of wall temperature to bulk temperature.

Jan 1, 1966

By Albert W. Deurbrouck

Twelve samples from six Barbour County coal beds were analyzed for this report. The samples collected were generally high sulfur content coals, frequently exceeding 3 percent in the raw-coal sample. Many of them could not be upgraded to acceptable metallurgical standards even by rigorous preparation procedures. The production of coal in the county in 1963 amounted to almost 3 million tons of which 44 percent was mechanically cleaned.

Jan 1, 1965

By R. V. Higgins

As part of a study of application of the Buckley-Leverett method to an analysis of oil-reservoir performance covering a wide range of relative permeabilities and oil saturations, a method has been devised for quickly deter-mining average water saturation at breakthrough from relative permeability data. The base for the relative permeability used in the report is either the permeability to air or the effective permeability to oil at the irreducible water saturation. The permeability to air also was used because of the large backlog of air permeabilities available to reservoir engineers. The basic data were calculated by an electronic computer and are presented in a single graph from which the point of breakthrough may be obtained. In this study the water saturation at the beginning of the depletion is the connate or interstitial or irreducible water saturation. These water saturations are considered to be synonymous and to have a practical value.

Jan 1, 1960