Search Documents

By H. E. Perlee

Mathematical expressions are derived for the histories of the pressure, flame radius, mass fraction burned, and burned and unburned gas temperatures associated with a spherical flame propagating concentrically in a spherical vessel. The equations are solved numerically for a 9.5 pct CH4/air mixture using the best available information for the burning velocity, expansion ratio, and specific heat ratio. Calculated histories are in complete accord with experimental measurements. The accuracy of calculated histories is determined relative to errors in the system parameters, and it is found that 10 pct errors in either the burning velocity or the expansion ratio results in a 40-pct error in the pressure history. A 10-pct error in either burned or unburned specific heat ratio results in a 22-pct error &apos;in the pressure history. It was further established that the usual assumption of constant specific heat ratio is unacceptable, but equating the burned and unburned specific heat ratios result in no apparent error in the histories. The cubic law (P = Kt3 + Po) is derived and discussed, and it is found that the law is valid only during the early period (P<2 atm) of flame growth.

Jan 1, 1974

By Kenneth L. Cashddollar, Terry G. Montgomery, Eric S. Weiss, John E. Going

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRI, Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test -was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere.

By Edward M. Kawenski

Tests were made in the Bureau of Mines Experimental Coal Mine on stop-pings similar to those used in operating coal mines to obtain information on air leakage through the face and the rupture strength of a stopping subjected to a pressure differential. Block stoppings were made from cinder, slag, and gravel aggregates with and without mortared joints and coatings. Sheet stop-pings were uncoated brattice cloth and nylon or brattice cloth and expanded metal-lath coated with asphalt, latex, mortar, or rigid urethane foam. Limited data were obtained on air through stoppings subjected to simulated roof convergence and to shock forces created by the firing of an adjacent charge of explosive. The pressure differential required to rupture stoppings was determined. shows that coating the face of a stopping effectively reduces ail: leakage. Block stoppings, particularly those with mortared joints, are most resistant to pressure and shock forces than are sheet stop-pings. Where ground movement is a factor, sheet stoppings leak less air than block stoppings.

Jan 1, 1965

By M. J. Ferrante

Low-temperature heat capacities and high-temperature enthalpies were determined calorimetrically for Na2Cr04, A reversible transition was found at 700° K with an isothermal heat of transition of 2,263 cal/mole. High-temperature X-ray diffraction analysis showed that the transition was a crystal change from the low-temperature orthorhombic form to the high-temperature hexagonal form. At 795° K the hexagonal form had the parameters a, = 5.691 and co = 7.478 A. Powder diffraction data for the high-temperature form are given and possible structures discussed. The melting point was determined to be 1,065° K with a heat of fusion of 5,810 cal/mole. Enthalpy and entropy increments from this investigation were combined with other data from the literature to calculate enthalpies of formation, free energies of formation, and equilibrium constants of formation from 298° to 1,400° K. Equations that represent enthalpies above 298° K are given.

Jan 1, 1972

By J. S. Tosh

The Federal Bureau of Mines has investigated the equilibrium of the system potassium carbonate (K2C03) potassium bicarbonate (KHCO3) potassium bisulfide (KHS) carbon dioxide (C02) hydrogen sulfide (H2S) water (H20). Partial pressures of hydrogen sulfide, carbon dioxide, and water vapor were measured at 70° to 130° C. over solutions of 20-, 30-, and 40-percent-equivalent potassium carbonate containing from 20 to 3,000 grains of equivalent hydrogen sulfide per gallon of solution. This study was made to obtain equilibrium data for evaluating the feasibility of using solutions of hot potassium carbonate for removing, hydrogen sulfide from gas mixtures. The equilibrium partial pressure of hydrogen sulfide may be correlated with the ratio of the molal concentrations of the solutes (KHC03) (KHS)/ (K2CO3). The relationship is shown graphically for the 30- and 40-percent solutions. Once this ratio is determined, the partial pressure of hydrogen sulfide can be obtained from the curves. The equilibrium data show that effective removal of both carbon dioxide and hydrogen sulfide can be achieved simultaneously with hot solutions of potassium carbonate.

Jan 1, 1960

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating hardrock mine, Grace Mine, located near Morgantown, Pennsylvania. Diesel-powered haulage equipment is used in this mine, and the electromagnetic noise environment it creates was measured to see how it differs from the environment created by electric-powered haulage equipment. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. Data are recorded using broadband analog magnetic tape and are later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and in amplitude probability distribution plots.

Jan 6, 1974

By M. C. Irani

The Bureau of Mines, in cooperation with the Mine Safety Appliances Co., has developed a new methane analyzer system for underground applications. Methane enters coal mine ventilation air from the breakup of coal at the active face, from the collapse of roof rock during retreat mining, and from the ribs abutting virgin coal. Each source contributes varying amounts to the total emission, depending upon rate of mining, type of mining, and the character of the coalbed and adjacent strata. The evaluation of individual parameters of methane emission requires the continuous monitoring of individual mine sections over a long period of time. The methane analyzer system was developed to meet this need. The system has been installed and operated in an active mine in the Pittsburgh coalbed. The system and details of its installation and calibration are described. Data are presented to substantiate its reliability.

Jan 1, 1975

By R. G. Sandberg

Many gold-bearing ores throughout the Western United States contain small quantities of mercury. The presence of mercury not only decreases the gold-loading capacity of the activated carbon, but complicates the fire refining of cathodes and creates a potential health hazard. The Bureau of Mines investigated methods to limit mercury extraction during gold ore leaching and to remove mercury from cyanide leach solu-tions. Mercury dissolution was reduced from 40 to 10 pct by decreasing NaCN concentration from 20 lb to 0.34 lb per ton of solution at a pH of <11. When 0.1 lb CaS per ton of ore was added to a leach slurry, mer-cury extraction was reduced from 27 to 0.4 pct. Less than 0.5 pct of the mercury was solubilized when <0.1 lb CaS per ton of are, along with lime and NaCN, was added to a simulated grinding circuit.

Jan 1, 1984

By W. W. Simpson

During cyanidation of mercury-bearing gold-silver ores, significant amounts of mercury are extracted. The presence of mercury decreases. gold loading and increases mercury stripping time on activated carbon, complicates fire refining of the gold cathodes, and creates a potential health hazard. Addition of calcium sulfide (CaS) to the cyanide leach slurry precipitates the solubilized mercury but also some silver. The Bureau of Mines investigated silver loss during CaS precipitation of mercury. Addition of 0.1 lb CaS per short ton ore to a mercury-bearing gold-silver ore precipitated both mercury and silver. However, if copper was added with CaS, or if the ore contained copper, much of the sil-ver loss was prevented. Addition of 235 ppm Cu with 0.1 lb/st CaS, prior to carbon-in-pulp adsorption, resulted in 89-to 97-pct, 80-to 91-pct, and O-pct adsorption of the solubilized gold, silver, and mer-cury, respectively, on the activated carbon.

Jan 1, 1986

By A. C. Johnson, McHenry Mosier

The Bureau of Mines has adapted its activities to needs of national defense and to conditions brought about by the war program . Its work is now oriented solely to war problems . After studying about 1,600 deposits of war minerals , exploration projects have been undertaken on 96 of the most promising , of which 56 have proved successful . These have indicated that 56 million tons of ore of commercial or near -commercial grade can be utilized to meet war requirements . Included in this amount are 1 million tons of tungsten ore ; 4 million tons of chromite ore, 10 million tons of manganese ore , 2 million tons of antimony ore , 1 million tons of mercury cre , and 28 million tons of iron ore . Work done in connection with exploration projects included 172,000 feet of surface trenching , 210,000 feet of drilling , and 21,000 feet of shaft sinking . Nearly 100,000 samples were taken, on which 500,000 analyses were made . Extensive metallurgical tests were made on ore from many of these deposits , both in the laboratory and in pilot plants , in connection with research to develop metallurgical processes for their treatment .

Jan 1, 1943

By J. W. Walkiewicz

The Bureau of Mines investigated alloys containing mischmetal (MM), cobalt, copper, magnesium, and iron for use in permanent magnets in place of the scarce samarium-cobalt alloys. The magnetic properties of MM-Co, MM-Co-Cu, MM-Co-Cu-Mg, and MM-Co-Cu-Fe-Mg alloys were evaluated. Magnets were fabricated by powder metallurgy consisting of arc-melting the metals, crushing and grinding the resultant alloys, alining and compacting the powder, and sintering the compacts. Magnetic values of MHc = 4.7 kOe, BHc = 4.07 kOe, Br = 6.81 kG, and (BH)max = 10.0 MGOe were obtained with a MM-Co alloy containing 36±0.5 wt-pct MM. By substituting copper and magnesium for part of the cobalt, the values for MHc and BHc were increased to 29.0 kOe and 5.89 kOe, respectively. This intrinsic coercivity value exceeded that of Sm-Co alloy obtained in our laboratory. The addition of iron to MM-Co-Cu-Mg alloys resulted in an increase of Br to 6.90 kG and (BH)max to 10.3 MGOe. Copper and magnesium contents of these alloys were optimized to obtain maximum values of MHc.

Jan 1, 1981

By L. A. Neumeier

The Bureau of Mines evaluated creep and other properties of extruded Zn-30 pct-AI alloys containing 0 to 0.7 pct Mg. The alloys were extruded both above and below the Zn-Al eutectoid temperature of 275° C. Creep behavior is defined for the alloys as extruded and after various heat treatments. Tensile properties, hardness, thermal expansivity, impact resistance, and microstructures are given. The alloys, either with or without magnesium, required substantially less pressure for extrusion near 275° C than at higher or lower temperatures. The alloys containing magnesium exhibited significantly greater hardness, tensile strength, and creep resistance, but much lower ductility than the 2n-30 pct Al alloy. The properties were very sensitive to the processing conditions.

Jan 1, 1971

By Donald S. Colby

CARBON-BLACK shipments, which had declined in the latter art of 1953, remained low in 1954 until after settlement of the labor strike that occurred in the rubber industry in July and August. The production of new model automobiles in the last quarter of the year spurred the demand for rubber tires and consequently the demand for carbon black. Total shipments of 1,498 million pounds for the year were 4 percent below 1953.

Jan 1, 1958

By Raymond J. Isherwood

The U. S. Bureau of Mines has investigated the domestic primary and secondary lead smelting and refining industries to determine the economic impacts of existing and proposed environmental, health, and safety regulations. The impacts are assessed in terms of capital and operating costs for existing and alternative smelting/ refining technologies. Industry response to regulatory implementation is estimated and quantified in terms of import value from lost lead production. For the primary lead industry, regulatory compliance may add up to 1.15 ¢/lb refined lead to operating cost for rehabilitated plants. Alternative smelting/refining methods could reduce net operating costs by as much as 4.36 ¢/lb refined lead. Capital expenditures would vary from $750 to $1,000 per annual mt of smelter capacity. Secondary lead smelter operating costs would increase about 3.8 ¢/lb refined lead to comply with existing regulations. Capital expenditures would average about $124 per annual mt of smelter capacity. Implementation and enforcement of proposed regulations would result in closure of the primary lead industry and additional expenditures for compliance by the secondary lead industry. Enforcement of the most extreme proposed regulations would force the secondary lead industry to close.

Jan 1, 1988

By James R. McVey

A new method for measuring deformations of rock surfaces in underground excavations has been suggested by Dr. James Powell of Brookhaven National Laboratories (BNL) and subsequently developed and successfully demonstrated in a mining environment by the Federal Bureau of Mines, Spokane Mining Research Center (SMRC) and Brookhaven National Laboratories. The system uses 35-mm photography of targets strategically located on surfaces of interest, such as across the roof and on the sides of a mine drift or tunnel. The optimum tar-get, as determined in this investigation, consists of a white ?X? made with 1/8-inch-wide reflective tape on a black 6-inch square. Photographs, taken in pairs from two separated camera positions and at regular time intervals, were analyzed at the Bureau by hand and at Brookhaven National Laboratories using techniques and equipment similar to those used in cloud chamber film analysis. Test results show that deformation-measurement accuracies of better than ±0.020 inch in a drift that is 20 feet wide can be expected. This degree of accuracy, plus providing displacement data in the X, Y, and Z directions (rather than the one direction formerly possible), makes this a noteworthy and useful tool for industry as well as for mining research.

Jan 1, 1974

By Noel N. Moebs

This report summarizes 10 selected Bureau of Mines research contract reports produced from 1970 to 1980 which consist largely of geologic studies of coal mine roof support problems. Significant highlights from the contract final reports are discussed and presented in practical terms. The selected reports focus on the Appalachian and Illinois coal mining regions. In the Appalachian coal region, two geologic structures, roof rolls and slickensides, predominate over all structures as features that directly contribute to roof falls. Studies of these and other structures are reviewed, and improved methods of utilizing drill core and core logs to prepare hazard maps are presented. Among the reports described are several on the weakening effects of moisture on shale roof, as determined from both laboratory and underground measurements, and an assessment of air tempering as a humidity-control method. Also summarized are findings concerning the time lapse between roof exposure and permanent support installation as a factor in the effectiveness of roof bolting.

Jan 1, 1984

By Ernest A. Curth

The Bureau of Mines studied pressure changes in coal pillars by using encapsulated hydraulic pressure cells to measure relative changes in stress developed during mining. The data indicate that (1) abutment stresses were detected when the pillar line is within 42 to 100 feet, (2) vertical pressure increases as coal is mined in the pillars, (3) at first pressure is higher at the edge of the pillar than in the core, but as mining progresses, the higher pressure is measured in the core of the stump, and (4) in the two instances where lateral pressures were measured, they remained lower than the vertical pressures during pillar extraction. The data also indicate that the mean vertical pressure increase, 6P, in a pillar is roughly related to the percent of pillar extracted, A, by the empirical parabolic equation

Jan 1, 1967

By Ralph H. Whaite

The Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region is described. A catalog of the maps that have been microfilmed in the Eastern Middle anthracite field--the first area to be covered in the program--is presented. Additional catalogs will be published as significant mining areas are completed.

Jan 1, 1965

By Ralph H. Whaite

The Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region is described. A catalog of the maps that have been microfilmed in the Eastern Middle anthracite field--the first area to be covered in the program--is presented. Additional catalogs will be published as significant mining areas are completed.

Jan 1, 1965

By W. E. Lamont, R. E. Perry, I. L. Feld

The Bureau of Mines conducted research to determine the conditions required to sinter a pyrrhotite calcine into a product suitable for iron blast furnace feed . The calcine , a fine - grained iron oxide produced by roasting sulfide flotation concentrate , analyzed about 60 percent iron and 1 percent sulfur . Sintering of the calcine without prior pelletization was not successful whereas firing of preformed calcine charges yielded acceptable sinter products . Batch tests were made to study the effect of the following variables on the sinter quality : Size of green pellets in the charge , quantity and type of internal carbonaceous fuel used , depth of sinter bed , moisture content of the charge , flux additions , and binder additions . The batch and continuous sinter tests showed that minus 1 / 4 - inch pellets prepared from a mixture of the calcine , coke , dolomite , and water gave sinter cakes analyzing 57 to 61 percent iron and 0.05 to 0.02 percent sulfur .

Dec 1, 1963