Search Documents

By L. M. Chan, D. H. Carlson, J. H. Johnson

"This paper discusses the evaluation and application of a portable parked-vehicle tailpipe emissions measurement apparatus (EMA). The EMA consists of an exhaust dilution system and a portable instrument package. The EMA instantaneously dilutes and cools a sample of exhaust with compressed nitrogen or air at a known dilution ratio, thereby presenting it to instruments as it is presented to personnel in the surrounding environment. The operating principles and governing equations of the EMA are presented.A computational method is presented to determine the engine operating and performance parameters from the exhaust CO2 concentrations along with an assumed engine overall volumetric efficiency and brake specific fuel consumption. The parameters determined are fuel / air ratio, mass flow rates of fuel, air and exhaust emissions, and engine brake torque and horsepower. These calculated engine parameters are used to characterize engine load when performing EMA in-field tailpipe sampling without a dynamometer, and to detect deteriorated engines.Evaluations of the EMA by comparison of diesel tailpipe measurements with those made using laboratory-grade instruments showed that the EMA measurements are accurate and reproducible. The results also show that the EMA is capable of detecting emission concentration changes resulting from engine faults. Calculated engine operating and performance parameters correlate and compare well with laboratory-measured values.The EMA in-field engine loading and tailpipe sampling procedures for parked vehicles are presented, and results of the EMA field measurements are also presented. Low coefficients of variation for repeat EMA tailpipe measurements on diesel-powered haulage vehicles in four underground mines indicate that the EMA in-field engine loading and tailpipe sampling procedures are reproducible.An analysis of EMA tailpipe measurements for three haulage vehicles in one mine shows that the EMA can: 1) identify haulage vehicles that emit excessively high pollutant concentrations, and 2) provide data needed to evaluate and determine the efficiency and effectiveness of tailpipe emission control devices.Finally, recommendations for a proposed commercial EMA system are presented. This commercial system would overcome many of the adverse features of the prototype EMA used in these tests."

Mar 1, 1992

By R. O. Dannenberg

This report describes aperiments by the Bureau of Mines and reviews theoretical aspects of the use of organophosphate solvent extraction for recovering beryllium from sulfate leach liquors. The leach liquors were prepared by sulfuric acid leaching of lime-sintered low-tenor beryl flotation concentrates. The experimental work on sulfate leach liquors showed that the acidic esters of organophosphates extracted beryllium slowly but in preference to aluminum. Three common alkylphosphoric acids, di- (2-ethylhexyl) (EHPA), heptadecyl (HDPA), and dodecyl (DDPA), in order of decrmsing selectivity, yielded a partial separation of beryllium from aluminum.

Jan 1, 1962

By L. C. IlsLey, H. B. Freeman

In connection with the approval of coal-cutting machines for service in gaseous mines , the engineers of the Bureau of Mines have been somewhat concerned as to the type of trailing cables that could safely be used on permissible outfits . While no final action has been taken on this question ( tentative approvals having been granted pending investigations ) , the Bureau has been endeavoring to collect data and information on this question which would permit a fair , yet safe , ruling to be made . For this purpose cooperative arrangements were made with three coal companies to visit certain of their mines , making inspections inside the mines to observe the cables and cutting machines in operation . In all , twenty mines were visited . A questionnaire covering the operations of trailing cables was filled out at each of these mines . In a few instances no personal inspection was made , the information being supplied by mine officials after conferences with the Bureau's engineer . At other mines the information given by mine officials was supplemented by personal observation inside the mines , usually at a time when the cutting machines were in operation .

Jul 1, 1923

By R. W. Watson

This Bureau of Mines report summarizes some recent results on the sensitivity of various experimental explosive systems using ammonium nitrate (AN) as the oxidizing agent. The sensitivity survey included drop-weight and friction testing and sensitivity to initiation by projectile impact and a No.8 blasting cap. It was found that certain types of AN prills can result in cap-sensitive mixtures when combined with No.2 diesel fuel (Fa); prilled AN mixed with nitromethane also result in cap-sensitive mixtures. Mixtures of AN prills and neat 1-and 2-nitropropane were not cap-sensitive, and the use of powdered or grained aluminum in AN-FO did not adversely affect the sensitivity except possibly to increase its sensitivity to friction.

Jan 1, 1974

By E. G. Valdez

Laboratory research demonstrated that ceramic wall and floor tile can be produced from electric furnace phosphorus slags composed of calcium silicates. Grinding the slag in a pebble mill, followed by magnetic removal of deleterious magnetite, produced a raw material that could be compounded and formed into wall tile by dry pressing, sintering, and glazing. The effects of process variables such as forming pressure and sintering temperature were investigated. Wall tile bodies produced by this method were comparable to commercial tile. The tiles were readily glazed to a smooth shiny finish and met ASTM Specifications C34-62 for structural clay load-bearing tile. The estimated cost of producing wall tile by this method compared favorably with the retail market value for similar wall tile. Addition of borax or other additives to the ground slag followed by dry pressing and firing likewise produced a commercial grade of floor tile.

Jan 1, 1974

By J. M. Mutmansky

"The objective of this study was to produce coal dusts for laboratory research that are similar to mine airborne dusts in chemical, mineral, and physical characteristics. In this investigation, dusts produced in laboratory comminution equipment were compared with continuous miner- generated dust for similarity in physical characteristics. Mining-generated dust (MGD) and bulk coal samples were first collected from an underground mining operation. The bulk samples were then processed in the laboratory for size reduction in various comminution devices. These laboratory- generated dust (LGD) samples were subjected to size and microscopic analyses. Physical properties of the dust particles were studied on a scanning electron microscope (SEM ). A numerical shape coordinate system (SCS) was also developed and applied to 300 particles from each sample. Statistical analysis was then performed on the collected data and characteristics of the MGD and LGD samples were compared. IntroductionIn many biomedical studies, researchers routinely introduce a dust mass into an experimental environment to assess the response of a biological entity, usually lung macrophages in vitro or a live laboratory animal, to the dust mass. To provide data of maximum usefulness, it is highly desirable to use dust with characteristics of actual mine airborne dust. The primary objective of this research was to produce dusts in the laboratory similar in chemical, mineralogical, and physical characteristics to mine airborne dusts. This paper outlines the evaluation of the physical characteristics of the lab-generated dusts.Particle shape analysis is perhaps the least-developed area in mineral-related particle science and technology. There are still no standard methods or instruments to scientifically quantify particle shapes. To date, many attempts have been made to characterize particle shapes. These procedures can be roughly classified into three categories:"

Dec 1, 1995

By R. V. Rahfuse

Noncaking 0- by 2 -inch subbituminous coal from New Mexico was gasified with air and steam at 205 prig using a stirred-bed producer to determine coal losses by entrainment in the gas for this low-sulfur, high-ash coal which contained 20 percent particles smaller than 1/16-inch sieve size. The use of fine-sized coal has particular importance because most production from mechanized mines is smaller than 2-inch size. This initial attempt showed technical feasibility for gasifying New Mexico subbituminous coal containing small-sized particles in fixed-bed producers without excessive coal loss by entrainment. Dust loss averaged about 2 percent of moisture-free coal, most of which was recovered from the gas. Ash clinkering was controlled by adding 1,010 lb/hr steam to reduce tempera¬tures in the combustion zone. Yield of low-Btu fuel gas, 150 Btu per scf, dry, amounted to 69,800 scfh from 1,490 lb/hr coal (as received) and 3,450 lb/hr air (dry).

Jan 1, 1974

By R. V. Lundquist

The specific conductance of solutions of sodium hydroxide and of sodium aluminate was directly proportional to the temperature. The specific conductance of sodium aluminate solutions with identical sodium ion concentration and at constant temperature decreased with increase in aluminum concentration. The aluminate ion population in solution was shown to consist of a mixture of monovalent and polyvalent ions. Aluminate ions did not influence the temperature dependence of pH in caustic solutions containing sodium aluminate. The density and viscosity of a solution was inversely proportional to the temperature and directly proportional to the concentrations of sodium and aluminate ions.

Jan 1, 1965

By Irving Hartmann

The fire end explosion hazard of excessive coal-dust deposits in mines has been recognized for many years, and important measures have been developed for reducing dust formation and to alley loose dust near its source. Nevertheless, in the course of normal mining it has been estimated that 1 to 3 percent (in some thin, friable seams up to 10 percent) of the total coal mined is reduced to dust of through-20-mesh fineness. In highly mechanized, continuous mining operations the production of fines is even greater. Most dust is trapped near its point of origin and removed from the mine, but large quantities are transported by the air current and by haulage into entries, where the greatest proportion settles on the floor and the balance on the rib and roof surfaces. The latter is generally finer in particle size than the floor dust; this, coupled with its more advantageous position for dispersion, makes the rib-roof dust (also to be referred to as overhead dust) a greater potential explosion hazard.

Jan 1, 1954

[ ]

Jan 1, 2012

By Alfred E. Schwaneke

A versatile torsion creep tester was instrumented with electromechanical and servomechanical components to operate automatically and unattended, producing digital printed outputs. The apparatus uses an electrical system for applying torsional stresses, and a unique angular transducer as a null detector operating a servocontrolled strain measuring system with the digital readout. The tester is designed to measure the creep in single-crystal or polycrystalline zinc, zinc alloys, magnesium, magnesium alloys, or other metals and alloys. Applied stresses may be varied from zero up to 2,000 psi in the outermost fibers of a 1/8-inch-diameter, 4-inch-long specimen. Strain readings to 0.001 degree, equivalent to a strain of 2.73 X 10-7, may be made automatically from one every 5 seconds to one per month. The apparatus has provisions for programed temperature control and special atmospheres or vacuum operation. A discussion of applications of the system to other mechanical testing apparatus is included.

Jan 1, 1970

By Frank E. Cash

The iron-ore ranges in the Lake Superior district are the liarquette in Michigan, Menominee and Gogebic in Michigan end Wisconsin, and the Vermilion, Mesabi, and Cuvuna in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. Accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year but closely approximate each other over a period of years. During the 4-year period 1940 to 1943, inclusive, 323,667,599 long tons of iron ore was shipped from the Lake Superior district.4/ Michigan and Wisconsin shipped 65,386,608 tons, or 20.2 percent of the total, and employed approximately 15,000 men; Minnesota shipped 258,280,991 tons, or 79.8 percent of the total, and employed approximately 10,000 men. The tons produced per man employed is much, greater in Minnesota than in Michigan and Wisconsin owing to the large open-cut production in Minnesota.

Jan 1, 1945

By W. M. Myers

Water has been commonly used as a collecting medium in many instruments employed in the sampling of dusty atmospheres in mines** add industrial plants, and for this purpose has much to recommend it, particularly the following factors:1.,Water is a very efficient dust collector.2.,Distilled water of great purity may be readily obtained at slight expense. The analytical error introduced by the extremely small amount of foreign matter in carefully distilled water is very small,3.,Water is a very convenient medium with which to work as all the analytical operations of diluting, aliquoting, and filtering are readily and speedily carried out. Water has therefore been used extensively in such instruments as the Palmer apparatus, the Greenburg-Smith impinger, and the dust collector recently described by Drinker, Thompson, and Fitchet. The Bureau of Mines has conducted investigations in many metal-mining districts of the country, determining of dust the nature and amount of dust present in working places, its effect the health of workers, and what precautions may be taken to decrease the hazard of exposure to dangerous dusts. The Bureau is therefore interested in any factor that affects the accuracy of dust sampling.

Nov 1, 1923

By H. Dolezal

An investigation was made on the use of magnesium for the direct reduction of rutile to make low-cost, offgrade titanium which could be upgraded to an acceptable grade of metal by electrorefining. Reductions made with charges containing magnesium chloride under hydrogen yielded products with oxygen con-tests close to the theoretical equilibrium composition. Two reduction products were made from rutile for use in electrorefining amenability tests: (1) a product from reduction in an inert atmosphere which contained 88.9 percent titanium and 4.42 percent oxygen, and (2) a product from reduction in a hydro-gen atmosphere which contained 92.5 percent titanium and 2.40 percent oxygen. Reduction products obtained under both of these conditions were amenable to electrorefining.

Jan 1, 1965

The U.S. Bureau of Mines evaluated water-jet-assisted longwall shearers in full-scale laboratory tests and underground. Both test programs showed that use of high-pressure water did little to reduce the shearer motor energy required to maintain a given cutting rate. However, three other major benefits were achieved with the use of water-jet-assisted cutting. At a pressure of 1,800 psi, respirable dust levels were reduced about 80 pct compared with the dust levels of the conventional water spray system operating at 340 psi. Operating at higher pressures required for water-jet assist also resulted in an increase in the average size of coal cut, which translates into a decrease in product fines. Finally, although no controlled measurements of bit wear as a function of water pressure were made, mine personnel reported that the shearer bits lasted longer when water-jet-assisted cutting was used.

Jan 1, 1989

By M. A. Mahtab

This report describes the procedures used by the Bureau of Mines for obtaining attitudes of joints surveyed with a borescope in inclined boreholes. An algorithm for computing the dips and azimuths of the observed joints is presented. The algorithm is used to solve an example problem. A computer program based on the algorithm is listed. It is hoped that the procedures described here will be useful in treating large quantities of data obtained from comprehensive borehole surveys.

Jan 1, 1973

By F. E. Griffith

Cost data are given for five methods of secondary backfilling of strip mines previously partially backfilled. The operations were conducted in north-central Pennsylvania; an average of 600 linear feet of highwall were backfilled in each trial. Major obstacles and the relative merits of the methods are discussed.

Jan 1, 1966

By W. T. Millar

Graphite in the Suffern deposits near Hillburn, N. Y., consists of flakes ranging in size from fines to one-half inch in diameter. The Bureau of Mines investigated the Suffern deposits in the spring of 1943. Gneiss outcrops were examined, and five trenches excavated and sampled. The graphite is not confined to any definite zone but occurs in small, local pockets. Eleven samples were collected and combined for laboratory tests. Tests by the Bureau of Mines indicate that the graphite ore can be beneficiated by stage crushing, "skin flotation" of coarse flakes, and wet flotation of minus 10-mesh flakes. Over 90, percent of the graphite was recovered.

Jan 1, 1949

By A. W. Ambrose

"A need exists for men in oil-field production work who correspond to the mining engineer of a large mining property. Some oil companies prefer to call such an employee a resident geologist, resident engineer, or a petroleum technologist. He should perhaps be more correctly termed a petroleum production engineer. The duty of such a man is to apply his scientific and geologic training practically to oil-field development work.He should be, by education, a mining, civil, or mechanical engineer, with a knowledge of geology and chemistry. Upon completion of his education, such a man should spend several years in the oil-fields. There are two means of gaining proper experience. The first method is to work for an oil company in making a detailed study of each well, collecting data on the history and production, followed by a preparation of good records, from which well logs can be prepared. From the well logs, the geologic cross-sections, peg-models, and structure contour maps can be made. These allow a comparable, detailed study of each well, which is necessary to solve many of the problems. Along with this the engineer should visit drilling wells daily for collection of samples of formations and for a proper study of how they drill. He should form friendly relations with the drillers and production foremen. The second method of gaining proper experience is to start work as a roustabout, pumper, or on the pipe¬line gang, finally working up to a tool-dresser. After three or four years of such work, the engineer may be classed as a petroleum production engineer."

Jan 1, 1920

By Robert P. Vinson

The U.S. Bureau of Mines evaluated a light-scattering technique for discriminating between spherical and nonspherical particles. This evaluation was a three-step procedure. The first step required collecting light-scattering data for a variety of particles. This was accomplished with a particle analyzer called the DAWN-A. The DAWN-A measured the scattered light intensities of individual particles at a forward scattering angle of 40°. These DAWN-A measurements of individual particles are called scattering signatures by the Bureau researchers. The second step in this evaluation was to calculate a sphericity index number using the scattering signatures produced by the DAWN-A. The sphericity index number can range from 0 to 1. A calculated sphericity index of 1 would show that based on the intensity of scattered light, the particle was a perfect sphere. The third and final step of this evaluation was the comparison of the calculated sphericity indices of the various particles. Comparing these indices made it possible to discriminate between the nearly spherical waterdrops and the nonspherical coal and rock dust particles.

Jan 1, 1993