Search Documents

By J. T. Schimmel

The purpose of this investigation was to obtain complete information on some of the uses of a 24-inch-diameter auger in the underground mining of pitching anthracite beds. The auger was placed in operation early in 1958 to drive ventilation connections between coal gangways driven by a continuous miner. Although designed to drill rise holes only, it was used also to drill dip holes. The latter holes were drill id from an adjacent gangway to avoid interference between the auger and the continuous miner. These holes established immediate ventilation returns when intersected by the continuous miner. Bureau participation in the project covered 361 working days. The auger was used on 288 shifts, usually one 7-hour shift per day, and drilled 3,246 feet, of which 493 feet were reamed. The longest hole was 87 feet; hence the maximum drilling depth of the machine (rated at 100 feet) was not required. Holes drilled normal to the strike of the bed ranged from 30 to 66 feet deep, averaging 45 feet. The continuous miner drove gangways on 575 shifts. Thus, the auger worked one shift for each two worked by the continuous miner and was used on less than 80 percent of the workdays. The auger drove 24-inch holes 10 times faster than the larger, conventional openings could have been driven by usual mining methods and exceeded the workload for which it was purchased. Augering eliminates exposure to the hazards encountered in driving chute-work by conventional methods and provides adequate circular ventilation openings, which are strong in self support and are adaptable to reaming when required. With alterations, the auger may have limited use as a production machine in thin-bed pitch mining but cannot compete with established methods of thick-bed pitch mining.

Jan 1, 1962

By C. M. K. Boldt

This report summarizes five separate Bureau of Mines contract studies on the use of aerial photogrammetry, satellite transmission of in situ instrumentation information, and satellite imagery to monitor and update mine waste embankment data. The equipment used, methods applied, results, recommendations, and cost analyses are presented along with a bibliography of related investigations.

Jan 1, 1987

By H. K. Kutter

The pressure pulse generated by an underwater spark \vas investigated in relation to its potential use for rock fragmentation. The study established (1) the relation between the peak discharge current and the peak wave pressure; (2) the relationships among the peak wave pressure, the discharge voltage, and the spark gap width; (3) the type and pulse duration of the generated wave; (4) the percentage of energy transmitted in the spark as a function of spark gap width and discharge voltage; and (5) the percentage of energy converted into the pressure wave as a function of gap width and discharge voltage. Spark-generated fractures were studied in two-and three-dimensional rock and plastic specimens. The laboratory results indicated that the pressure pulse generated by an underwater spark is a potential practical tool for rock fragmentation. The paper contains an appendix describing the capacitive pressure gage specially developed for the laboratory tests.

Jan 1, 1969

By R. Van A. Mills

This preliminary paper is intended to answer briefly some of the inquiries coning to the Bureau of Mines regarding the so-called "paraffining", of oil wells and methods of preventing and remedying that trouble. The increased difficulties in operation and the losses of production caused by the deposition of gummy and waxy hydrocarbons, commonly called paraffin, in the wells, tubing, other pumping equipment, and in the pores of the productive sands, have long been recognized but the trouble has not been overcome. The nature and causes of the trouble, together with some of the possible methods by which it may be diminished or overcome, are outlined below. Character of the Peraffining Materials. The so-called paraffin that collects in oil wells end in the pores of the oil-producing sands immediately around the wells, is generally made up of amorphous wax or uncracked paraffin, asphalt, or other gummy hydrocarbons mixed with more or lees water, oil, and inorganic silt. Some of the samples of this "paraffin" collected from oil wells in different fields and examined by the Bureau of Mines contain as mach as 20 per cent by weight of water and inorganic silt, whereas other samples are composed entirely of waxy hydrocarbons and oil. The inorganic silt accompanying this "paraffin" is mostly fine sand, clayey materials, common salt and finely disseminated precipitates of calcium and magnesium carbonates. Sulphates of calcium, barium, and strontium are less common constituents of the "paraffin."

Jan 1, 1923

By R. L. Stein

For the past several years, the Bureau of Mines has been actively engaged in developing two new oxygen self-rescuers through research contracts with private industry. These new oxygen self-rescuers are designed to be carried by a miner while he is at work and are used during emergency escape, supplying high-purity oxygen to the user and, at the same time, absorbing carbon dioxide (C02), The first of the two new self-rescue breathing devices is a 10-minute, self-contained apparatus developed by the Mine Safety Appliance Co, Size and weight of the unit are comparable to the currently used self-rescue devices. The second device, designed and developed by Lockheed Missiles and Space Corp., is 8. 4.5-lb package which supplies 1 hour of oxygen to the miner. Both devices have a canister which contains the oxygen-producing and CO2-absorbing potassium superoxide chemical, a breathing bag, a bite-type mouthpiece, noseclip, goggles, and hoses connecting the canister and mouthpiece. When needed in an emergency, the miner removes the outer protective cover and dons the unit. For both devices oxygen is immediately available once the mouthpiece is placed in the mouth. These two new units have received prototype approval from the National Institute for Occupation and Safety Health (NIOSH) and the Mining Enforcement and Safety Administration (MESA).

Jan 1, 1976

By H. Schultz

Urban refuse that was mechanically separated at the U S Bureau of Mines pilot plant in College Park, Md., was successfully evaluated for its fuel values using standard coal analysis methods. Analyses performed on refuse samples taken from five sample points included moisture, ash, sulfur, chlorine, and heating value. It was recommended that characterization of the combustible portion of urban refuse by standard coal analysis procedures should be widely adopted.

Jan 1, 1975

By James C. Barker

Gold placer deposits along the upper Yukon River, in the region between the river villages of Circle and Eagle, were investigated by the Bureau of Mines. The investigation was conducted intermittently between 1976 and 1985 as part of an evaluation of mineral resources on lands proposed for inclusion in the National Park System. At least 230,000 troy ounces (tr oz) of gold has been produced in the region, principally from Woodchopper, Goal, and Fourth of July Greeks. The placers are underlain by, or occur downstream of, early Tertiary sediments that have been deposited in the Eagle Trough. Strike-slip displacement along the Tintina Fault is responsible for creation of the trough and may have been a factor in the formation of the present placers. Placers were found to have a close spatial correlation to certain altered fault lineaments of the Tintina Fault trench. Placer concentrates contain several different textural forms of gold, suggesting multiple origins. Geological studies and a survey of 162 panned concentrates throughout the region indicated previously unreported sites of placer gold, and potential exists for the discovery of additional placer and lode gold. Because of nearly continuous soil and vegetation cover, further evaluation of the region will require subsurface sampling.

Jan 1, 1986

By D. Harrington

The occurrence of dusts in underground workings creates many difficult and, in some instances, contradictory and conflicting problems for workers, operators, and all others interested in health and safety in mining and tunneling. Moreover, there are many misconceptions both as to the actual effect of most dusts which may be encountered in underground work and as to remedial or alleviating measures. Although the harmfulness of mine dusts to health of miners has been mentioned by man; writers in ancient times, much of our really authentic knowledge of the effect of underground dusts upon health or safety in both coal and metal mines has been pained during the past 30 or 35 years. There has been, however, a considerable amount of generalizing from some local condition or occurrence or theory rather than arriving at conclusions after extended studies and observations made not only in mines and tunnels but also in town, camps, and plants, and comprising date on as many different mining and tunneling localities, conditions, etc., as could be secured with reasonable expenditure of time or money. This paper dives sortie observations based on the writer's 30 odd years of experience in and around both coal and metal mines, including approximately 20 years? close study of dust disease with detailed surveys and reports on dust occurrence and effects in considerably more than 100 mines in probably 20 States of the Union. The observatio are those of an engineer and in many respects conflict the with "going" ideas of doctors, pathologists, and others who have written on dust disease. Were the word dust is used in this p: per in connection with respiratory disease, it refers to solid particles which float or can float in the air breathed by workers. Although these particles are usually dry, they may be wet; in general, their dimensions are so small as to be invisible to the nailed eye. Dusts in coal mines which may be involved in the initiation or extension of explosions, are generally thought to be those which are smaller than 20-mesh in size but chiefly finer than 20-mesh; coal-mine dusts which are harmful to health of workers have essentially the same general physical characteristics as other dusts, but usually consist of smaller particles.

Jan 1, 1936

By Oliver Bowles

The term "stone" in its broader sense includes not only the well-known limestone, marble, granite, sandstone, and slate but also precious and semi precious stones and many minerals and rocks not included in the principal groups. Stones have long been used for structural and ornamental purposes. To be so used, they must be cut to various shapes and sizes, and some must be polished to bring out their inherent attractiveness.

Jan 1, 1958

By Ivan F. Avery

PRODUCTION of carbon black decreased 4 percent in 1961. Output in the major producing States of Texas and Louisiana decreased 1 percent and 8 percent, respectively. Production of channel black continued downward, declining 10 percent in 1961 compared with 9 percent in 1960. Furnace black production also decreased 3 percent from 1960. Total domestic sales, however, increased 2 percent, Sales to most major consumers increased, but sales to the ink industry decreased 10 percent. Producer's stocks decreased 5,083,000 pounds during the year. Exports decreased 4 percent. SCOPE OF REPORT Carbon black is a very pure grade of quasi-graphitic carbon; particle diameters range from 50 to 5,000 angstrom units. Annual reports were submitted to the Bureau of Mines by operators of all commercial plants in the United States.

Jan 1, 1962

By T. T. Campbell

Research conducted by the Bureau of Mines demonstrated the feasibility of preparing columbium and tantalum metals by the application of Kroll-process techniques. Yields in excess of 95 percent were obtained in a modified Kroll-process reduction apparatus constructed from nickel and Inconel.4 Operating conditions during reduction and distillation were determined. Optimum temperatures during sodium reductions ranged from 650° to 750° C and for magnesium from 700° to 800° C with retort pressures ranging from 3 to 7 psig. Undesirable vapor phase reactions occurred when temperatures exceeded 750° C during sodium reductions or 850° C with magnesium. Vacuum distillation at 850° C effectively removed volatile salts and excess reductant from the reduced metals. Calculations based on the results obtained in small scale tests indicate that reaction rates of up to 34 lb/hr could be obtained during columbium reductions and up to 60 lb/hr during tantalum reductions in production scale reac¬tors. The small, laboratory-scale techniques used in this study could be adapted to commercial practice. The reduced powder or sponge metals can be consolidated by conventional arc-melting techniques, and the arc-melted metals can be fabricated into ductile sheet at room temperature. Analyses of arc-melted buttons prepared from Kroll-process tantalum or columbium showed that tantalum of greater than 99.8-percent purity was obtained and that columbium purity exceeded 99.7 percent. A significant purification of the reduced metals occurred when they were consolidated by electron-beam melting, and the purity and ductility of electron-beam-melted Kroll-process tantalum and columbium compared favorably with the commercial metals. After electron-beam melting, the purity of the tantalum exceeded 99.95 percent, and columbium purity was approximately 99.9 percent.

Jan 1, 1962

Because surface mining removes the original plant cover from the land and exposes the soil, special care is needed. Until the mined land is stabilized by revegetation, snowmelt and rainfall can pick up sediment and erode mined lands much faster than undisturbed areas. Sediment control is an important aspect of protecting the environment during mining and reclamation because without it, large amounts of sediment can clog streams, increase the risk of flooding, damage irrigation systems, harm aquatic habitat, and limit the use of water for other purposes. Stream quality can be affected many miles downstream from the mine. Before SMCRA was implemented many streams were degraded by uncontrolled sediment from mining. Sediment is controlled through careful planning and a design that incorporates a variety of measures that work together to reduce soil erosion at the mine. Disturbed areas are graded, and some areas terraced, to achieve stable slopes, reduce runoff water velocity, increase infiltration, and divert runoff into drainage channels so that it flows away from unvegetated, erodible areas. Grading along the slope contour and scarify in gun vegetated slopes with bulldozer track marks help prevent erosion by slowing down the flow of water. Runoff from haul roads is controlled by culverts and roadside ditches. Sedimentation ponds or other forms of sediment control are required at all mines to minimize the amount of sediment leaving the site.

Jan 1, 1992

By Arnulf P. Hagen

This project was designed to explore the suitability of using fluorinated inorganic materials as solvents for the in situ mining of thin seamed, heavily overburdened coal; to build a data base for the selection of an inorganic solvent for use for coal cleaning; to determine if fluorinated solvents will reduce the organic and inorganic sulfur contents of the coal, as well as to lower the ash content. The coal samples have been combined with pure solvent, as well as with aqueous solutions at atmospheric pressure and at increased pressure. The increased pressure experiments are important since they duplicate the conditions anticipated for an in situ cleaning and mining operation. Trifluoroacetic, difluorphosphoric (phosphorodifluoroidic), and trifluoromethanesulfonic acids have been found to be effective for the cleaning of high sulfur, high ash coal at 300°C and at atmospheric pressure. At pressures up to 20,000 psi the effectiveness of these reagents is not decreased.

Jan 1, 1983

By R. Blickensderfer

Test equipment that simulated frictional impacts between coal-cutter bits and mineral inclusions at a coal face during operation of a continuous coal mining machine was used by the Bureau of Mines in the laboratory to study the incendivity of impacts between various rocks, metals, and hard-metal alloys in an explosive mixture of air-7 pct natural gas. Quartzitic sandstone was found to be the most incendive of several rocks tested. Limestone concretions from a coal seam, known locally as "sulfur balls," sparked furiously but were not incendive. Among the metals tested, the type of steel used in commercial coal-cutter tools was the most incendive material tested. A l7-4PH stainless steel was less incendive and appears to be the most promising high-strength steel alloy, reasonably economical, for use in coal-cutter bits. Some hard-metal alloys, primarily titanium and zirconium diboride composites, were also evaluated as possible replacements for the conventional cobalt-bonded tungsten carbide used in the tip of coal-cutter bits. The metal-bonded diborides were generally less inc endive but more brittle than the conventional tungsten carbide. Carbonitride coatings on tool bits were also tested but found to have no advantage. The source of ignition during frictional impact between metal and rock was studied. Immediately after impact, a yellow flash was observed and a smear of metal near its melting point occurred on the rock. This hotspot on the rock, rather than the yellow flash or sparks or metal fragments, was observed to be the cause of the ignition.

Jan 1, 1974

By M. L. Odenbaugh

The viscosity reduction effect of varied concentrations of leonardite (a naturally oxidized form of lignite) and leonardite-caustic on the rheological properties of a standard bentonite drilling fluid was studied and evaluated. The minimum plastic viscosity was found to occur at application rates of 4 lb of leonardite and 1.33 lb of caustic per barrel of drilling fluid. Leonardite-caustic treatment was not beneficial in treatment of salt-contaminated drilling fluids. Although filter loss rate was reduced; both yield values and gel strength were increased. Compared with other viscosity control agents) including quebracho) ligno-sulfonate) humic acids extracted from leonardite) as well as other reaction products of lignite) leonardite is less effective at low application rates but is an effective treating agent at rates of 2 Ib/bbl or more. Considering the comparable merits of the substance tested) the major factor in determining which agent to use should be based on cost consideration.

Jan 1, 1967

By David E. Siskind

The Bureau of Mines has studied the fracturing produced in the vicinity of large-diameter blastholes in Lithonia granite. Cores were taken from the vicinity of AN-FO production blasts and examined using a total of seven laboratory and field measurement techniques to delineate zones of damage and evaluate the effectiveness of the seven diagnostic tests for fracture-state determination. Laboratory measurements of acoustic pulse velocity, porosity, permeability, compressive strength, and Young's modulus indicated the extent of fracturing with the acoustic techniques providing the best means of distinguishing between fractured and unfractured core. A severely fractured zone was found to extend approximately 25 inches (64 cm) from the center of the 6-l/2-inch blastholes, equivalent to 8 blast-hole radii. A second zone, characterized by a lesser degree of fracturing extended from 25 to 45 inches (64 to 114 cm) or 8-to l4-blasthole radii. Beyond 45 inches (114 cm) the rock was undamaged.

Jan 1, 1974

By R. Ward Stahl

Fire has been one of man's most useful tools through the ages and certainly is a "must" for industrial progress but when uncontrolled is one of the most destructive agencies. This fact is even more important in a coal mine, where many persons and much expensive equipment are confined in a relatively small area. Means of escape from a burning area, as well as from the products of combustion, are often limited; and in many instances the entire surroundings are combustible. Numerous mine fires, which resulted in a high death toll and great financial loss through the years, have caused mine owners to search for the best fire-fighting equipment; much of this has been installed, the quantity depending largely upon the experience of the individual companies or neighboring mines in certain coalfields. A mine owner or operator has meager published information on the actual fire protection afforded and systems of fire-fighting inaugurated in the coalfields, by which he could compare his efforts and get some idea of the adequacy of his own protection. To further general knowledge of the subject, it was decided to survey a representative number of mines in the field and show what has been accomplished. Representative mines were selected in various coal beds; some had similar tonnage, so comparison could be made if desired.

Jan 1, 1957

By Thomas R. Bur

Symmetry theory, based on ground work established in the study of single crystals and experimental procedures utilizing ultrasonic pulse velocities of spherical specimens plotted on equal area polar projections, enables the direct identification of a material's elastic symmetry system and the determination of its orientation, as well as the position of the elastic coordinate axes. The method is especially useful for elasticity studies of polycrystalline and amorphous materials for which this knowledge of symmetry is a prerequisite in determining the independent elastic constants. Projections based on theoretically derived velocities are given for a single crystal from each of the major crystallographic symmetry systems except the triclinic. Projections based on experimentally derived velocities are given for one brass and several rock spheres.

Jan 1, 1969

By Sumner M. Anderson

ATHOUGH scattered signs of increased activity in the mining industry accompanied an incipient improvement in the overall economic situation during the latter months of 1963, production levels for the year as a whole responded to the general 1962-63 business recession with a 4.2 percent decline. The petroleum industry, active since 1907, did not become a dynamic force in the economy until exploration and drilling contracts were concluded with private companies in 1958 and 1959; on November 15, 1963, having virtually achieved self-sufficiency in petroleum in the preceding year, those contracts were unilaterally annulled. In the field of metallics, the only approach to internal sufficiency-aside from the iron and steel industry that has depended heavily on the importing of basic raw materials-has been in mining, smelting, and refining lead and zinc although iron ore, silver, beryllium, tantalite, and tungsten have been mine production items of economic significance. Reserves of lead, zinc, silver, bismuth, vanadium, and low-grade and metallurgically difficult iron ore-as well as those of beryllium, tantalite, and tungsten which are produced primarily for export-appear to be fairly abundant. The exploration of deposits of copper, cobalt, tin, lithium, gold, manganese and uranium has been undertaken on a relatively small scale, and little precise information is available on the extent of reserves. Argentina is dependent on foreign sources for part of its required iron and steel and, except for lead and zinc, most of its nonferrous metals. Nonmetallies and solid fuels present an exceptionally varied array of production items among which cement had the second largest 1963 output in South America. Borates, bentonite, common clay, diatomite, fluorite, granite, lime, limestone, obsidian, onyx, rhodochrosite, salt, and spodumene ordinarily are produced for export either exclusively or in excess of domestic consumption requirements. Barite, cement, chalk, gypsum, marble, and mica are both exported and imported. Argentina depends entirely or partly on imports for coal and coke, certain special types of clay, mineral abrasives, graphite, magnesite, mineral fertilizers, sulfur, talc, and minerals for construction, the last group being chiefly attributable to convenience of river transport from Uruguay.

Jan 1, 1964

By K. C. Strebig

The effect of some organic additives in diamond drilling of quartzite was investigated in the laboratory with a drill instrumented to measure the rate of penetration, the thrust, and the torque and to record each as a function of the distance drilled. A statistical plan was followed throughout the investigation, and an equation representing the bit performance was derived from the mathematical theory of reliability. The coefficient of friction in drilling increased with the use of additives, although the wear coefficient decreased. The decrease in wear associated with an increase in energy per unit volume consumed and the increase in penetration rate resulted in a net decrease in the cost per foot of drilling. A hypothesis explaining the effects achieved with the additives is given.

Jan 1, 1971