Search Documents

Control respirable dust in underground coal mines through selection of optimum water spray pressures. Approach Through underground trials at longwall and continuous mining operations, the relationship between operating water spray pressure and respirable dust levels at the machine operator's location was determined. Defining the Application Water sprays are used for two significantly different control applications. On longwall mining machines, sprays are commonly installed both on the body of the machine and on the cutting drum. Sprays on the body of the machine are used to redirect dust which has already become airborne away from the machine operator. Each spray acts as a small fan, directing the primary airflow over and around the machine and towards the face, away from the operator. The energy of this system is directly related to the spray pressure. Higher pressures move more air, but care must be taken not to cause turbulence and boilout into the walkway. Sprays mounted on the drum are, effective at suppressing the respirable dust at the bit/coal interface and preventing it from becoming airborne. Again, these sprays must not impart excessive energy to the dust particles thus stirring up more dust than they suppress. While mounting sprays on the shearer drum is standard industry practice, there is no reliable technology available to successfully mount water sprays on the cutting drum of continuous miners. Instead, sprays are mounted on the machine body, close to the drum, and directed at the cutting head. This allows the water to reach the bit/coal interface and mix with the cut material. Here again, care must be exercised to prevent these sprays from imparting excessive energy to the dust particles and stirring up more dust than they suppress. These sprays can also cause dust "rollback" from the face, toward the operator, if operated at too high pressures.

Jan 1, 1986

By McHenry Mosier

Although local conditions at each mining property affect the percentage of increase in drilling speed for a given reduction in gage of bit, the results of drilling tests conducted at the Mount Weather testing adit show such a large advantage in favor of the smaller gages that they should be indicative of the possibilities at most mines. GENERAL DISCUSSION Although it is common knowledge among miners that drilling speed ill- creases with reduction in gage of bit, the large amount o this increase is not so universally realized, A recent Bureau of Mines4/ survey of drilling practices in 28 metal mines showed that the maximum gage of starters is 3 inches and that at 50 percent of the mines starters are 2-1/4 inches or larger, Because this size appears too large for conditions at most' mines where abrasion is moderate and where powder distribution permits, the use of smaller bits presents a favorable opportunity for reducing drilling costs.

Jan 1, 1939

By Ronald D. Hill, Elmore C. Grim

The cost of reclamation can vary widely, depending on the primary objectives of the restoration activities. statistics in this study originated from State files, publications, and personal communications relating to restoration and pollution control measures for previously mined lands (orphan lands) and active mines. Reclamation of orphan lands is generally considered a public burden and constitutes an economic problem. All work reported here was completed under government contract, by the lowest bidder, with money coming from State and/or Federal funds. Cost would have been substantially lower had the reclamation been concurrent with mining. Several persons connected with some of the projects have observed that costs could probably be reduced by at least one half, if the reclamation had been conducted along with the mining. The expense of clearing and grubbing of volunteer vegetation, disposal of buried trees and brush, loosing of compacted spoil, and re-establishing access to areas could be saved. In addition, a contracting firm doing the work for a government agency would have mobilization costs and receive a profit. Mining companies also are profit conscious and would consider these costs in anticipating their profits (e.g., overhead would be less if reclamation is integrated with mining). The data presented here should serve as a guide for estimating and determining cost ranges, however, it should be recognized that variations exist. Adjustments may be necessary from the standpoint of physical conditions, economic conditions, price changes, and more restrictive requirements of recent surface mining laws. Reclamation conditions, procedures and successes in the eastern United States, particularly in Appalachia, have no bearing on conditions to be expected in the western United States. The situations are wholly different. Reclamation in the West differs from th t in the East, primarily because of aridity especially a during the summer months 1). Because of the many variables and differences between reclamation in eastern and western areas, they will be discussed separately.

Jan 1, 1974

By Thomas E. Marshall, Gerald L. Finfinger

The Bureau of Mines has developed a practical methodology for deter- mining occluded gas contents of domal rock salt samples. The method, which is portable and field worthy, provides results in 5 min or less and does not require a laboratory environment or specially trained personnel to obtain meaningful results. The results can be used to identify gas-enriched zones, and thus may aid mine operators in production planning or ventilation design. The test method is based on the relationship between gas content and the acoustic response of salt samples as they are dissolved in water. The relationship is defined by an equation, and the results are repeat- able. The equation was derived by testing a series of rock salt samples collected from domal salt mines in Louisiana.

Jan 1, 1987

By J. I. Paige

The Bureau of Mines, U.S. Department of the Interior, conducts research on methods to minimize the requirements for mineral raw materials through conservation, substitution, and increased minerals and metals recovery from primary and secondary domestic resources. To further this goal, prior Bureau research had devised a pyrometallurgical technique (RI 8211) to recover metallic iron and copper from molten copper smelting furnace slags by carbothermic reduction. As a continuation of this Bureau research on the carbon injection technique, reverberatory and electric furnace slags were treated in an 800-kva electric arc furnace by simultaneously top feeding the slag and injecting coke breeze into the bottom of the molten bath. Results of the tests show that 76 to 89 pct of the copper and up to 48 pct of the iron contained in the smelting furnace slag were recovered in a metallic phase, while 56 to 82 pct of the carbon injected into the sys-tem was utilized as the reductant. Laboratory evaluation has shown that the metal product, which contains 86.9 to 95.0 wt-pct iron and 1.3 to 4.1 wt-pct copper, will be a satisfactory medium for recovering copper by cementation. The expected energy consumption for the process is 110 kwhr per ton of molten slag treated and 520 kwhr per ton of solid material charged.

Jan 1, 1982

By L. C. IlsLey

Briefly, a permissible schedule of the Bureau of Mines establishes certain minimum standards for safety; it gives details of test methods adopted to determine whether these standards have been met, and a list of charges for such tests. Any manufacturer has the privilege of submitting his product for test in accordance with the conditions outlined in the schedules. His action is wholly voluntary, for the Federal Government has no jurisdiction as to what equipment shall be used in mines, this authority being left to the various States. When the product of a manufacturer has met the schedule requirements, he is permit¬ted to advertise this fact and to attach an approval plate with the bureau's seal to each machine he makes that is identical in every way with the equipment tested, inspected, and approved by the bureau. This work of approval has grown by the addition of new schedules until at present a great many mines are using one or more classes of permissible equipment, and there is still a demand for other approved apparatus in the ever-widening field of electrically operated machinery. The safety of electrical equipment of this type depends on four fundamentals, namely, (1) correct principles of design; (2) proper assembly of parts at the factory; (3) proper assembly and installation of equipment at the mine; (4) and proper operation and maintenance after installation. The first two factors are within the province of the manufacturer. The bureau either inspects and tests several models of one product, such as electric cap lamps, or one model, such as an electric motor. If this series of tests proves satisfactory, the manufacturer is given the privilege of making other appliances, and assembling them in the same way; the approval plate he attaches is his guaranty that the equipment is identical with the one tested and inspected by the bureau. The third and fourth factors concern those who use such permissible equipment, and it is to them that this paper is mainly addressed, in an effort

Jan 1, 1922

By James P. Rider

This U.S. Bureau of Mines report describes a viewing transformation algorithm that generates a perspective view of a three-dimensional scene. This tool may be used by researchers to improve mine safety by assessing the visual capabilities of a mobile equipment operator. Three-dimensional transformations used to build the viewing transformation and techniques used to project the image onto a two-dimensional display screen are defined. The algorithm is written in the C-programming language and designed to stress portability, allowing it to work without significant modifications on numerous computers. A listing of the computer routines along with sample output is included in the report.

Jan 1, 1992

By Charles L. Kimbell

Tables 16 through 19 continue the series of providing the world merchant fleet distribution by type of vessel and the ranking of the major fleets by country of registry. Table 20 this year provides a summary of the world's liquid gas carrier fleet. These vessels are included in the totals given for the world's tanker fleet, but gives a breakdown demonstrating the growth of the importance of natural gas in the world's energy commodity consumption. Panama and Suez Canals Tables 21 and 22 provide the latest available information on the transit of mineral commodities through the Panama Canal, by number of vessels, direction, and the commodities transported. Although the number of vessels transiting the Panama Canal dropped slightly (0.5%) between 1989 and 1990, the total amount of cargo moved rose by 3.6% and the amount of mineral commodities moved rose by 7.2%.

Jan 1, 1993

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal nonfuel mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1982

By Elizabeth A. Johnson

The effect of slag composition on lead losses to slags and on the behavior of associated accessory elements in lead blast furnace smelting has been studied by the Bureau of Mines. Equilibrations of 30 g of lead and synthetic slag doped with Cu, In, TI, and Sb at 1,200° C in CO-C02 atmospheres revealed the importance of the FeO:Si02 ratio and the basicity ratio, (CaO+MgO):SiO2, of the slag. Lead losses to slags increased with an increasing FeO:Si02 ratio and decreased with an in-creasing basicity ratio. Copper and indium distribution coefficients, [Lx =] increased from 15 at the lower basicity ratios to near 60 at higher basicity ratios. LTI values increased from 20 to 150 as slag basicity increased. Lcu, Lin, and LTI were relatively in-dependent of the FeO:Si02 ratio, but increased with greater amounts of accessory elements in the system. Antimony distribution alone was shown to be strongly affected by FeO:Si02 ratio, although data were scattered. LSb values ranged from 20 to 800 and decreased sharply with increasing FeO:Si02 ratios. The basicity ratio and the level of accessory element load did not have any noticeable effect on LSb.

Jan 1, 1983

By W. A. Cole

The sulfur shortage that existed during the Korean conflict stimulated interest in coal measures as possible sources of sulfur. One of the areas brought to the attention of the Bureau of Mines was in Marion County, Iowa, where comparatively high-sulfur coals and other marcasite-bearing strata were known to occur. A Bureau of Mines engineer inspected the marcasite occurrence on December 4, 1954; this prompted further work on the Iowa coals and associated formations as a source of iron sulfides. An investigation of the Iowa high-sulfur coals was undertaken including core drilling, field reconnaissance, and compilation of data pertinent to consideration of the following: 1. Upgrading Iowa coal by mechanical cleaning and the feasibility of recovering sulfur from coal brasses. 2. Possibility of processing the high-sulfur coals by adaptation of methods employed in processing industrial gases to produce sulfur and sulfur products. 3. Possibility of finding concentrations of iron sulfides in associated rock formations in sufficient quantity for economical recovery.

Jan 1, 1957

By F. L. Wideman

SPURRED by demands of a buoyant economy for mineral products, output from mines in the United States established a new record. Removal of waste material, necessary for the extraction of economic minerals, kept pace with mine production. Earth moving by these two activities exceeded 3 billion tons, an increase of 5 percent over that of 1963. Crude materials from which metal or nonmetal products were derived accounted for 75 percent of the total. The remainder, mostly worthless, was classified as waste. Changes in the minerals industry result from many causes. Technological trends and labor productivity are among several significant and interrelated indexes that assist in the analysis of the changes. Therefore, a. study of productivity is helpful in measuring technological growth in mining. Concepts of productivity tend to vary with the purpose for which the term is used; frequently, productivity is expressed in terms of units of output per unit of labor, such as tons of ore per man-hour or man-shift. Comparisons of levels of productivity for a group of products are usually made using composites of output. Data for all metal and nonmetal mines except gold, silver, mercury, platinum metals group, and sand and grave were used to compile the composite for determining productivity for 1960-64. Copper ore, iron ore, and phosphate rock are mined mainly by surface methods, but characteristics of the deposits and differences in processing the crude material affect production of the commodities. Therefore, productivity data for these selected segments of the minerals industry reflect the influence of physical conditions on the exploitation of them.

Jan 1, 1965

By A. F. Jolly

As a part of ongoing research into the sulfidation partitioning of selected complex minerals, the U.S. Bureau of Mines conducted research designed to selectively recover Cu from sulfidized chalcopyrite (CuFeS2). Ferric chloride (FeCI3) solutions leached >90 pct of the Cu and <20 pct (sometimes < 10 pct) of the Fe in the sulfidized concentrates. Cupric chloride (CuCI2) leaches were even more selective, solubilizing essentially 100 pct of the Cu and < 5 pct of the Fe. In contrast, leaching non-sulfidized CuFeS2 with either FeCl3 or CuCl2 showed that somewhat more Fe than Cu dissolved. These studies demonstrate that Cu is substantially more leachable from sulfidized CuFeS2 than from nonsulfidized CuFeS2? The Cu-and Fe-bearing constituents generated as sulfidation products, CuS (covellite) and FeS2 (pyrite), respectively, are differentially dissolved. The solubility of Fe from pyrite in sulfidized CuFeS2 is much lower than the solubility of Fe from complex nonsulfidized sulfide where Fe and Cu are bound in the same crystal lattice. Thus, the Cu dissolves selectively, producing a high-Cu filtrate from which Cu can be recovered by cementation or by electrolysis. Flotation of CuS-FeS2 mixtures indicates partitioned phases can be physically separated if effective liberation can be achieved. Magnetic separation tests yielded less promising results.

Jan 1, 1991

By S. J. Hussey

The Bureau of Mines investigated the applicability of carbon-in-pulp pro-cess for recovering silver from low-grade ores. The reasons for the research were (1) to illustrate a practical procedure for the process design of carbon-in-pulp adsorption circuits using leach slurries and simple equipment; and (2) to illustrate how equations of adsorption theory relating rate data and equilibrium adsorption curves can be helpful in process design. Carbon-in-pulp silver adsorption tests were made on Banner, Idaho; mine-run ore samples with silver contents ranging from 2.0 to 8.5 oz/ton and variations in cyanide leach extraction from 48 to 93 pet. The lower recoveries were attributed to the presence of complex silver sulfide minerals. Carbon-in-pulp batch adsorption tests provided rate data for the estimation of a silver equilibrium adsorption curve. Process design procedures in which the rate data were related to an equilibrium adsorption curvey by equations of adsorption theory were used to plan a four-stage pilot plant cascade. The pilot plant was successfully operated for 45 hr of countercurrent flow, producing a carbon product containing a mean silver loading of 571 oz/ton from a pregnant solution of 1.7 oz/ton of silver. Virtually all of the dissolved silver was recovered on the carbon.

Jan 1, 1978

By Martin Hertzberg

In this Bureau of Mines report, the optical detection of fires and explosions is considered fundamentally. The measured spectral radiances from methane-air ignitions are compared with the background irradiances from stray and ambient sources, and with the spectral sensitivites of various sensors. The comparison naturally suggests the optimum spectral ranges and signal processing logic that can uniquely characterize the ignition event. Both ultraviolet (UV) and infrared (IR) are considered. Several alternate sensing methods are proposed and discussed. The development and testing of an IR system designed for use in ignition suppression devices in mines is described.

Jan 1, 1975

By L. W. Higley

Particulates generated in electric furnace (EF) steelmaking constitute approximately 1 to 2 pct of the charge. This flue dust is a rich source of zinc (values are substantially higher than in ore), but although there are several processes for recovering the metal, none are considered economic in the United States. This report reviews extraction technology and presents results of Bureau of Mines reduction-volatilization tests on pelletized EF dusts which achieved high recoveries of zinc. The data are sufficiently encouraging to warrant consideration of EF dusts as raw material for primary zinc smelters.

Jan 1, 1977

By Eugene T. Sheridan

This report presents statistical data on individual plants in the fuel- briquet and packaged-fuel industries circularized by the Bureau of Mines, United States Department of the Interior, in its 1957 annual survey. This survey revealed that 17 briquet and 23 packaged-fuel plants were active part or throughout the year. The annual production capacity of the fuel-briquet industry was 3,088,000 net tons, a decrease of 17 percent from 1956. The decline in capacity was caused in part by the permanent retirement of 4 plants and also by the reduction in capacities of 4 other plants. The rate of production of briquet plants also decreased as the industry operated at 35.8 percent of capacity compared with 40.9 percent in 1956. Every operating plant in 1957 had an annual capacity exceeding 25,000 tons.

Jan 1, 1958

By Thomas P. Mucho, William D. Monaghan, John Wood, Michael A. Trevits

We have tested the ability of ground penetrating radar (GPR) to resolve adjacent mine workings. The work was conducted at two National Institute for Occupational Safety and Health locations – an underground coal mine and an underground limestone mine. The objective of our work was to determine if GPR signals could be received from distant mine workings. The GPR system was calibrated on underground mine pillars of known dimensions using a variety of antennas. The system was then tested at several underground locations in an effort to detect an adjacent drift entry; and an adjacent abandoned coal mine. As a means of verification, an in-seam horizontal hole was drilled from the active coal mine to the abandoned mine to confirm the presence and location of the abandoned mine workings. Our results show that in the case of the limestone mine the maximum depth of penetration where the mine workings could be resolved was 85 ft; and in the case of the coal mine the abandoned mine workings could be resolved at a depth of 205 ft. We conclude that it may be possible to utilize GPR for initial underground mine studies followed by directional drilling to accurately delineate the extent and position of adjacent abandoned mine workings.

By W. L. Hunter

Eleven steelmaking heats are described in this Bureau of Mines report in which acid practice was used to produce carbon steel from pre reduced iron ore pellets. Furnace slags obtained with no flux addition to the charge became quite viscous as they cooled, which precluded pressure casting from a ladle. Lime was added to the furnace charge at two levels to eight of the heats to modify slag characteristics in the furnace, and to the ladle in two heats to further modify the ladle slag cover. Selected ingots from nine heats were successfully rolled on a commercial mill to produce No. 10 reinforcing bar.

Jan 1, 1974

By Charles Anema

The Mancarried and Helicopter Receivers were developed under the contract I for trapped miner location. This program was a five phase program with 15 mancarried and 5 helicopter production receivers delivered under Phase IV and equipment documentation required under Phase V.

Jan 11, 1976