Search Documents

By Kenneth L. Rubow, Virgil A. Marple, Bruce K. Cantrell

"In a cooperative study by the University of Minnesota and the U.S. Bureau of Mines, diesel exhaust and mineral dust concentrations have been measured for aerosols generated in the laboratory and in five underground coal mines. Three mines utilized diesel-powered haulage equipment and two used all-electric equipment. Two source apportionment techniques have been applied to differentiate between the mineral dust and diesel exhaust aerosol concentrations measured. The first technique, using a micro-orifice, uniform deposit impactor (MOUDI) for size selective sampling, is based on modeling aerosol size and the premise that the diesel exhaust portion of the aerosol is predominantly submicron and the mineral dust portion is mostly greater that one micrometer in size. The second technique, Chemical Mass Balance (CMB) modeling, was used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results.The MOUDI size distribution data were modeled to obtain parameters describing the fine and course fractions of the sampled aerosol and to estimate the contributions to each mode from both mineral dust and diesel exhaust aerosol sources. The results showed the size distribution of the mixed aerosols exhibited two definite modes with the minimum between the modes occurring at 0.8 µm. Less than 5 pct of the coal mine diesel aerosol was found in the coarse size fraction. CMB analysis confirms the original premise for using aerosol size to separate diesel exhaust and mineral dust aerosol during sampling.Based on the results from the size selective sampling, a personal diesel aerosol sampler has been developed for measuring diesel aerosol mass concentrations. Th.is sampler uses an inertial impactor to size separate the respirable aerosol at 0.8 µm. All material less than 0.8 µm is collected on an after filter for subsequent gravimetric analysis."

Jan 1, 1990

By P. Comba

The U.S. Bureau of Mines investigated a hydrochloric (HC1)-calcium fluoride (CaF2) leaching procedure to treat domestic manganese (Mn)-bearing silicate resources. The proposed process is an alternative to high-temperature and energy-intensive extractive techniques. Single-stage leaching with a stoichiometric amount of HCl and a F-Mn mole ratio of 0.2 extracted 96 pct of the Mn when the leach conditions were 50° C, 3 h, and 35 pct solids. Ninety-eight percent of the Mn was extracted during countercurrent leaching at similar conditions. A process flowsheet was developed that incorporated HC1-Cab leaching, excess leach acid utilization, fluoride (F) recycle, and Mn recovery. When the domestic manganese silicate ore was processed, 98 pct of the Mn was extracted, 99 pct of the Cab was reclaimed, and a leach residue was produced that passed the Environmental Protection Agency (EPA) Extraction Procedure (EP) Test for nonhazardous waste.

Jan 1, 2010

By R. V. Ramani, K. V. K. Prasad, M. Swaminathan

"Engineering design involves, in addition to numerical calculations, considerable amount of expertise and judgement. The expertise and judgement is required to conceptualize and idealize the problem, select a suitable mathematical model for the problem and to interpret the model results in terms of stipulated design constraints. In recent years, knowledge based systems (KBS) have provided the capability to integrate the qualitative experiential and expert knowledge with ~he quantitative knowledge for improved analysis and design of systems. A possible KBS architecture for mine ventilation system design was discussed by Ramani and Prasad · (1987). The expert system (ES) component of the KBS supports the analysis and interpretation phases of the ventilation design process with an algorithmic program used for the solution of alternate designs. The purpose of this paper is to discuss the data and knowledge needs for developing such a system and a formal means of their representation on the computer. A number of ES shells were evaluated to explore possible development and delivery environments for the system. A brief summary of this evaluation is also provided.INTRODUCTIONLuxbacher and Ramani (1979) have discussed the design process of mine ventilation systems and have provided the interrelationships that exist between ventilation, strata control, drainage and material handling systems and mining methods. They have also outlined the importance of correct analysis of the problem, choice of the right solution method and a rigorous interpretation of the solutions. The expertise required for analysis and interpretation phases was identified as the key element in developing effective and efficient ventilation system designs. Such expertise is embedded in the right choice of questions to be asked of the user as well as in directing the user to a wide array of alternative methods that may satisfy the design requirements. With advances in artificial intelligence applications in recent years, particularly expert systems, the integration of expertise into traditional mine planning and design algorithms has been facilitated. These planning and design aids, employing the integration of numeric and symbolic logic and called coupled systems, are powerful tools for engineers to tap the benefits of experts (Kitzmiller and Kowalik, 1985; Fenves, 1985). The purpose of this paper is to discuss the means of representing knowledge for the design of mine ventilation systems through the use of a coupled system. The KBS is visualized as consisting of the following components:"

Jan 1, 1989

By Richard L. Lewis

This is a discussion of the application of the zonal harmonic series to problems involving dipole sources in the vicinity of spherical boundaries. The application of a formal zonal-harmonic series solution to directly obtain numerical results involves two distinct problems: namely, the convergence of the series solution and the accurate calculation of the special functions involved in the series solution. Some interesting techniques will be introduced which help to improve the convergence properties of the series solution.

Jan 1, 1973

By Maria I. De Rosa

This report analyzes mobile equipment fires for all U.S. surface and underground coal and metal/nonmetal mining categories by state and 2 year time periods during 1990-1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from MSHA mine fire accident publications and verbal communications with mine personnel. The analyses will provide the National Institute for Occupational Safety and Health (NIOSH), the Mine Safety and Health Administration (MSHA), and the mining industry with a better understanding of the hazards associated with mobile equipment fires and will create a basis for future fire research programs.

Jan 1, 2004

Develop a cost-effective, flexible method for extinguishing underground coal mine Fires that can be readily used in fire conditions encountered in both abandoned mines and coal outcrops. In addition to the abatement of an underground coal fire, a secondary objective was to prevent subsidence by filling the voids with a material having sufficient compressive strength to minimize subsidence. Approach The Colorado School of Mines Research Institute was awarded a research contract to determine the viability of using Foaming Mud Cement for abating underground coal mine fires and preventing subsidence. The program consisted of a laboratory and pilot scale investigation and process development. An extensive, controlled test program was conducted simulating floor, rib, roof and rubble fire conditions. Field demonstrations were conducted after the pilot scale research was completed. How It Works Traditional techniques have targeted the control of burning by eliminating the air, fuel source or heat. This has been accomplished by trenching, quenching, mothering or combinations of these three methods. These techniques were not always successful, particularly in the case of fires in abandoned mines.

Jan 1, 1991

Provide a method of detecting and locating miners trapped underground following a mine disaster. Approach Develop a surface deployed system which senses the vibrations caused by a trapped miner pounding on the roof of the mine and effectively determines the miner's location. How It Works If trapped underground, a miner would strike the roof of the mine with any implement at his disposal. This pounding causes vibrations in the ground which are transmitted to the surface where they are sensed by receiving transducers called geophones. Multiple geophones are positioned together for noise cancellation purposes in a form called a subarray. Seven

Jan 1, 1981

By Fred Leighton

The least squares method of rock noise source location presented is shown to be more accurate and reliable than standard direct solution methods. This method is particularly effective in improving solutions from rock noise locations outside of geophone array boundaries. A least squares solution for a medium .in which the seismic velocity is the same in all directions is also presented. In this special case, one can solve for both the source coordinates and the velocity.

Jan 1, 1972

Provide a means to (1) rapidly disconnect a multifunctioning signal channel from a multichannel data collection system, (2) protect electronic devices from damage while causing the minimum amount of data collection disruption, and (3) operate electronic devices under gassy mine conditions. Background Data collection system instrumentation and cables are often located in hazardous areas of underground coal mines. As a result, frequent damage to the instrumentation cables occurs from roof falls, heavy equipment, and the relocation of air, water, and power lines. A similar problem exists in surface areas where cables and instrumentation can be damaged by animals and by vehicle traffic. Without a circuit-breaking feature, the damaged cables could cause instrumentation to be ruined, cause power supply failure, and otherwise disrupt data collection in some situations the lack of a circuit-breaking feature might cause an ignition in a methane atmosphere.

Jan 1, 1990

By W. E. Anable

A 180° magnetic deflection residual gas analyzer mass spectrometer with a mass range of 2 to 200 amu was used to study the nature of gases evolved during arc and electron-beam melting of certain reactive and refractory metals. The partial pressure of residual gases over molten Mo, Hf, Ti, and Fe, was found to be similar: Water and hydrogen were evolved from the samples and from the furnace components, carbon dioxide and carbon monoxide resulted from deoxidation of some of the melts. Argon and acetone were residuals in the system, and methane was a decomposed organic compound from the oil diffusion pump.

Jan 1, 1969

Develop new technolgies and techniques which enable recovery of strategic and critical minerals such as cobalt from domestic resources, thereby easing the U.S. dependence upon foreign producers for these valuable commodities. Approach The Bureau of Mines, through research, developed a process which uses mineral beneficiation techniques to recover cobalt-rich products from Missouri lead ores. Before development of this process, cobalt was lost as an impurity in the copper, lead, and zinc concentrates and in the mill tailings because the technology to recover it with minimum impact on present production did not exist.

Jan 1, 1989

By A. Mayton, A. Brien, W. Porter, O&apos

In 2004, management at Unimin's Gleason, TN operation began implementing ergonomic interventions specifically targeted to reduce risk of musculoskeletal injuries (MSIs). Together with corporate and site management, Unimin identified work site hazards and began to modify work practices/equipment. Some interventions were relatively simple and were implemented immediately. Others, like improvements to a mobile shredder, were more complex but were eventually resolved through a participatory approach with employees, management, manufacturers and NIOSH. This paper discusses ergonomic interventions that were successfully implemented using a bottom-up approach to reducing the risk of injury.

By D. J. Bauer

Solvent extraction separation of light group rare-earth elements in a quaternary ammonium compound-chelating agent system was demonstrated in single-stage studies, Typical separation factor values obtained were 93 for lanthanum-praseodymium, 5.4 for praseodymium-neodymium, and 11.6 for neodymium-samarium. These values are significantly higher than those obtained using organophosphate extractants. Further studies in a 20-stage countercurrent mixer-settler resulted in the production of 99 percent lanthanum (oxide basis) at 96-percent recovery. Subsequently, 88 percent of the neodymium with a purity of 92 percent was recovered in the raffinate.

Jan 1, 1971

By M. D. Schlesinger

Mercury exists in coal in minute quantities, but the large tonnages of coal consumed could represent relatively large amounts of mercury entering the environment. Limits have now been placed on the emission of mercury, and it is important that reliable analytical methods be available to the chemist. The Bureau of Mines has evaluated analytical techniques used by a number of laboratories; most used vapor phase atomic absorption as the final detection method. Neutron activation was used by some of the laboratories. All of the methods described could be applied, but they require careful manipulation to prevent loss or mercury contamination. In the samples analyzed the mercury content ranged between 0.05±0.01 and 0.4l±0.06 part per million.

Jan 1, 1972

Improve the performance of waterjet nozzles used for water-jet-assisted cutting to optimize rock cutting efficiency. Approach The performance of a longwall shearer equipped for water-jet-assisted cutting was evaluated during an earlier study (Tech News No. 277). Waterjet nozzles were used to direct the solid streams of water that impacted the rock near the tip bits. The maximum water pressure that could be delivered to the nozzles was about 6,000 psi. Due to the "break up" of the solid stream of water, some of this pressure was lost before the water reached the rock. The pressure could have been increased by moving the nozzle closer to the bit tip but) moving the nozzle too close increases the possibility of damage to the nozzle. Study Results A test apparatus was built to measure water pressure at the location of water jet impact (see illustration). The target, a tungsten carbide plate with a 0.013 inch diameter orifice, was placed at the location of water jet impact. A pressure transducer, used to monitor impact water pressure, was positioned under the plate. Water pressure at the nozzle was maintained at 6,000 psi. The distance between the nozzle and target was varied from 2 to 5 inches.

Jan 1, 1988

Reduce the noise radiated by the auger miner cutting head (typically 105 dBA at the face) by 10 dBA without compromising the durability or productivity of the tool. Approach Research was conducted by the Bureau of Mines to identify the noise sources of auger miners with emphasis on the cutting head and coal cutting process. The overall noise level generated by the coal cutting process was found to depend greatly upon the structural characteristics of the auger cutting head. Based on this information, a quieter cutting head was

Jan 1, 1982

Provide mine personnel with a convenient means of determining the optimum installation geometry of roof trusses in bedded roof. Background Mine operators frequently ask the following questions concerning roof truss installations: 1. Where should the bearing plates or brackets be placed or where should the inclined holes be started? 2. At what angle should the holes for the inclined chords or angle holts be drilled? 3. What tension should be put into the inclined chords so as to achieve the most effective results for the effort and expense? Truss hardware manufacturers have responded to these questions with answers based on what seems to work best. While designs based on past experience are frequently reliable, there was a need for a rational approach that could accommodate a variety of conditions. The Bureau has developed a procedure that enables mine operators to optimize roof truss installations in bedded roof.

Jan 1, 1989

By B. J. Scheiner

A ferrous chloride-oxygen leaching system was investigated by the Federal Bureau of Mines to determine its effectiveness for recovering copper and silver from a tetrahedrite concentrate that had been pretreated to remove a majority of the antimony. The pretreated concentrate contained coppers, silver, lead, zinc, antimony, and arsenic. Parameters affecting metal extraction (such as temperature, pressure, amount of ferrous chloride, and initial hydro-gen ion concentration) were studied. Copper extraction of 98 pct was achieved by leaching 4 hours at 40 pounds per square inch gage (psig) and 100° C. Copper was recovered from leach solutions by cementation with iron, and the resulting ferrous chloride was recycled. Leaching the residue with cyanide followed by electrowinning recovered 99.7 pct of the silver. Iron, antimony, arsenic, and sulfur reported to the tailings.

Jan 1, 1978

By Neil B. Young

Analytical results for nahcolite, dawsonite, total extractable alumina, and oil yield are presented for samples representing Green River Formation oil shales in the saline section of two cores from Colorado's Piceance Creek basin. Analyses are also reported for samples extending the analyzed section of Colorado corehole No. 3 beyond that reported previously. These data permit evaluation of the deposit for possible production of three coproducts--shale oil, alumina, and sodium carbonates--from the saline section of the formation at these sampled points.

Jan 1, 1970

By Brian Kenner, Peter Swanson, Todd Krahenbuhl

NIOSH has developed an automated PC-based seismic event (induced earthquake) monitoring system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network is a central feature of the system. Mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface. Seismic event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system’s design philosophy, hardware and software components, examples of installations, and a few observational results.