Search Documents

By D. W. Frommer

Processing of nonmagnetic taconites by selective flocculation-des liming and anionic flotation of calcium-activated silica has been investigated using innovative procedures as a means of improving operating costs. Areas chosen for cost-cutting evaluation were grinding, fine screening, and water conservation and reclamation. The investigation was performed on Marquette range nonmagnetic taconites in the Bureau of Mines Twin Cities Metallurgy Research Center flotation pilot plant, at feed rates ranging between 900 and 1,100 lb/hr. With fully integrated water reclamation, flotation concentrates containing 65.8 percent Fe and 3.4 percent Si02 were made in the best operating period, with accompanying weight and iron recoveries of 40 and 74 percent, respectively. During this same period, the estimated cost of both flotation and water reclamation reagents was only $0.80 per ton of concentrate (1968 pricing basis). This cost is about 15 percent lower than obtained previously at this Center for flotation reagents only. The investigation demonstrated additional potential savings in operating costs of approximately $0.96 per ton of concentrate through autogenous grinding as a substitute for ballmilling. Fine screening of intermediate concentrates was employed advantageously, but the frequency of blinding may be a factor militating against use of the screen in this flotation system.

Jan 1, 1973

By G. T. Brow

An experimental method is described for testing diffusion of gases in crude oils at pressures and temperatures up to 3,000 psia and 200° F. A sampling technique was developed to withdraw by constant-pressure mercury displacement about 60 µl of oil from the diffusion cell through any of several 1/2-in vertically spaced capillary tubes and to trap about 4 µl of the oil in a specially designed microsampler. Oil trapped in the microsampler can be completely inserted in the sample inlet of a chromatograph. From analysis in a three-stage chromatograph (GLC), gas concentration in a sample is determined from the ratio of gas peak heights to area of peaks of reference components (hexanes or heptanes) in the oil. A diffusion coefficient is calculated from measured concentration profiles with known equations for diffusion in finite or semi-infinite systems, depending on whether the gas has or has not reached the end of the oil column. Results are given for a test of methane diffusing at 2,560 psia and 160° F in crude oil from the Weber Sandstone reservoir in the Rangely field, Colorado. A constant diffusion coefficient of 3.34 X 10-5 cm2 per sec was obtained which gives a good fit between calculated and experimental profiles determined at six times after start of diffusion. The maximum standard error of gas concentration determinations experienced with this method was ±0.88 ml per ml of gas-free oil.

Jan 1, 1970

By M. L. Whisman

The Bureau of Mines developed a radiotracer method for detecting the contribution of selected components and additives to thermally induce deposits of turbine aircraft fuels. Fuels were examined before and after 52 weeks of storage at 130° F. Of particular concern was the influence of aromatic hydrocarbon fuel constituents on thermal-stability quality of jet fuels during storage. A microfuel coker test apparatus was used to thermally stress the test fuels and blends, and the resultant contribution to deposits of selected fuel components, labeled with carbon-14, was determined by radioactive-counting techniques. Ninety-one blends of five test fuels with carbon-14-labeled fuel additives or components were prepared, tested, stored for 52 weeks at 130° F, and reanalyzed for deposit-forming tendency. These additives included two anti-oxidants, a metal deactivator, and a corrosion inhibitor. Of the labeled hydrocarbon fuel systems studied, the greatest reaction was observed in blends containing methyl-and ethyl-substituted indenes. Other aromatic types also showed some contribution to the deposits. Three of the additives showed a marked tendency to degrade and react during storage and thermal stress. A cresol antioxidant, however, barely contributed to deposit formation. Oleic acid interacted with cadmium present in aircraft fuel systems and produced deleterious effects upon the thermal-stability quality of the fuel.

Jan 1, 1971

By F. D. Wang

The Bureau of Mines has developed a computer program for evaluating pit slope stability by the finite element stress analysis and limiting equilibrium method. The program includes the finite element method of stress analysis using triangular elements, finite-element model mesh generation, plotting of the model mesh and stress contours, calculation of a factor of safety along a circular or a plane failure surface, and location of a critical circular failure surface. Instructions for preparation of input data, an example problem, and the program listing are presented.

Jan 1, 1972

By Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industry despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. In order to reduce cases of Noise Induced Hearing Loss (NIHL) in the mining industry, retrofit acoustic treatments and controls are being developed to subdue noise at the source. The Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2005 has determined that continuous mining machines rank first among all mining equipment whose operators exceed 100% noise dosage. The continuous mining machine conveyor, used to move coal from the cutting face to the rear of the machine, has been identified as a dominant noise source. A dual sprocket conveyor chain was tested as a potential solution. Sound power level measurements conducted at the Pittsburgh Research Laboratory (PRL) accredited reverberation chamber showed a 3 dB reduction in the A-weighted sound power level when the dual sprocket chain was implemented. Underground results show an 8-hour Time Weighted Average (TWA8 hrs) reduction a 3 dB for continuous mining machine operators. Utilizing this newly developed noise control, along with previously proven controls, provides continuous mining machine operators an opportunity to be within the MSHA-Permissible Exposure Limit (MSHA-PEL).

Jan 1, 2009

By Stephen Gerard Sawyer

The Bureau of Mines developed a method for analyzing elastically certain types of protective cabs and canopies used on underground electric face equipment. The method is based on plane frame theory, and to be amenable to analysis by this method, cabs and canopies must contain symmetry about one plane. Additionally, protective structures with one or more top members in the long direction that do not frame into the columns should be approximately twice as long as they are wide and have two or more internal top members in the short direction. The assumptions and limitations of the plane frame method as regards analysis of three-dimensional cabs and canopies are discussed. A step-by-step procedure for application of the plane frame method is given, and three example canopies are analyzed following this procedure. Elastic strengths calculated for the three example canopies compare within 10 percent of those computed by the more complicated space frame analysis. Formulas employed in plane frame analysis of cabs and canopies are given in the appendixes.

Jan 1, 1973

By D. E. Shanks

The Bureau of Mines investigated the effects of HCI concentration and solution temperature on the solubility and crystal form of the chlorides of Co, Mn, and Ni when sparged with HCI gas at temperatures of 20°, 40°, and 60° C. Increasing HCI concentration in solution caused the chlo-rides of Co, Mn, and Ni to crystallize (salt out) because of the common ion effect. The salting-out crystallization was most effective for NiCI2, which had a solubility of 0.7 pct at 20° C and maximum HCI concentration. COCl2 salted out to a minimum solubility of 9.4 pct at 20° C and 22 pct HCI concentration and increased in solubility at greater HCI concentrations because of the formation of chloride complexes. MnCl2 was intermediate in behavior. The effect of temperature on solubility was greatest for CoCl2 and least for NiCI2, 15 and 7 pct change, respectively, over the temperature range of 20° to 60° C. The salted-out chlorides of cobalt and nickel formed the hexahydrates and those of manganese formed the tetrahydrate in saturated metal chlo-ride solutions at 20° C and low concentrations of HCI. Increasing the temperature or the HCI concentration caused a 108s in waters of hydra-tion. At 60° C, the salted-out crystals of NiCl2 formed the tetrahydrate in HCI concentrations up to 18 pct and the dihydrate at higher concentrations, while cobalt and manganese chlorides formed the dihydrates, even in water.

Jan 1, 1985

By F. Garcia, J. Cervik

The cross-measure borehole technique has been shown by the Bureau of Mines to be an effective method of controlling methane liberated by fracturing the roof strata in longwall gobs where overburden is less than 750 ft (229 m). Boreholes are drilled into roof strata before mining operations affect the roof strata. Longwall mining fractures the roof strata and releases methane from source beds. Surface exhausters or vacuum pumps are used to draw the gas to the surface through an underground pipeline and vertical exhaust hole. The captured methane is thus prevented from entering the mine's ventilation system. About 71 pct of the methane produced by longwall mining in the Lower Kittanning Coalbed was captured by the cross-measure boreholes. Borehole spacing is an important factor affecting the performance of the technique. Interference tests and measurements of methane flows in return air indicate borehole spacing in the Lower Kittanning Coalbed should be limited to about 200 ft (61 m) except on the first 600 ft (183 m) of the longwall, where spacing should be reduced to about 100 ft (30 m) to capture the large quantities of methane released when the first large roof fall occurs. Comparisons between measured and calculated gas pressure differentials on boreholes indicate borehole length can be reduced from 280 to 140 ft (85 to 43 m), which reduces drilling costs significantly. Additional experimentation is necessary to verify the calculations.

Jan 1, 1985

By Donald A. Wilson

As part of a continuing effort to maximize metal recovery from domestic secondary resources, the Bureau of Mines investigated a process for recovering the metallic portion of scrap alkaline batteries. A pyrometallurgical method for recovering nickel and cadmium from Ni-Cd scrap batteries previously developed on a laboratory scale, was scaled up to 25-and 43-pound charges. The method employed reduction and/or decomposition in a retort using a minimum of 2.5 percent carbon as a reductant. Metallic cadmium was distilled at atmospheric pressure and a minimum of 900° C. Purity of the recovered cadmium was 99.8 percent minimum and the nickel-iron residue contained less than 0.02 percent cadmium.

Jan 1, 1981

By Charles C. Boley

The Bureau of Mines dried and carbonized two wood wastes, one softwood (redwood) and one hardwood (oak), using continuous, vertical entrainment techniques previously developed for use with coal. It was demonstrated that these techniques are readily applicable to wood waste and that appreciable changes in the yields of carbonization products can be obtained by varying operating conditions. A limited amount of experimental work was done on briquetting the char-coals. Firm briquets were formed with oak charcoal, although greater quantities of starch binder than used commercially for kiln-produced charcoal were required. Redwood charcoal did not briquet successfully under the test conditions employed.

Jan 1, 1969

By Charles L. Kimbell

Following the pattern established in the 1989 edition of this study, the concept of data availability must be addressed, because there are perceptible changes from year to year, and the availability of accurately reported, precisely defined statistics and nonstatistical information provides the only sound basis for analytical studies of any type. As the countries of eastern Europe, including the numerous states that formerly comprised the U.S.S.R., undergo the transition from centrally planned economies' to market economies, there has been a perceptible increase in information availability for rather obvious reasons. Any industrial operation seeing economic assistance from government and/or private sources outside the country in which the facility is sited must provide some appraisal of its operations at the time it seeks assistance, as well as some information on previous performance to serve as tools in evaluating its potential under the proposed development scheme for which it seeks financial assistance. This situation, coupled with governmental recognition that concealment of much of the national mineral production, trade, and consumption data for purposes of national security probably never was really necessary and certainly proved unnecessary with the end of the so-called cold war, has led to the publication of increasing amounts of both statistical and nonstatistical information in the countries undergoing economic transition.

Jan 1, 1993

By Edward D. Thimons

The Bureau of Mines conducted in-mine tests to determine correction factors applicable to low-velocity airflows (below 150 fpm) measured by the smoke cloud, vane anemometer, and oil of wintergreen tracer gas techniques 0 The average correction factors found for these methods of measurement were lower than those reported in the literature for use with higher velocity measurements. All tests measured airflows with controlled average velocities ranging from 50 to 100 fpm. Correction factors averaged about 0.75 for readings taken by the centerline smoke cloud method, remotely controlled and stickheld center" line anemometer, and split traverse stick-held anemometer. For hand-held centerline anemometer and oil of wintergreen tracer gas readings, correction factors averaged about 0.67. Since special anemometers are needed to measure airflows in this low-velocity range, and since proper calibration of these anemometers is difficult and expensive, the use of anemometers for low-velocity measurement is imprac-tical. On the other hand, smoke and oil of wintergreen give results as con-sistent as those obtained with specially calibrated, low-velocity anemometers. Furthermore, they are easy to use and inexpensive.

Jan 1, 1979

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume n of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output!' It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1979

By Berenice B. Mitchell

THE STATISTICAL tables in this chapter present, country by country, the mineral production of the world in 1949-50. The figures are on a mine basis, unless otherwise indicated, except for cement, coke, and steel, which are measured at the processing plant. The tables are essentially a retabulation, by countries, of the 53 commodity world tables appearing in the various chapters of this volume. For lack of comprehensive information, data for the following minerals are excluded: Andalusite, aplite, asphalt, boron, bromine, calcite (optical), calcium chloride (natural), carbon dioxide, clay, columbium (niobium), diatomite (kieselguhr), dumortierite, emery, garnet (abrasive), gem stones (other than diamonds), germanium, greensand, grindstones, helium, indium, iodine, kyanite, lithium, magnesium compounds (other than magnesite), meerschaum, mineral pigments, monazite, natural gas, natural gasoline, oil shale, olivine, perlite, pumice, quartz crystal, radium, sand and gravel, selenium, sillimanite, sodium salts (other than common salt), stone, strontium, sulfur (byproduct), tantalum, tellurium, thallium, topaz (industrial), tripoli) uranium, vermiculite, wollastonite, and zirconium. In addition, a few minor geographic areas for which no statistics are available, are also omitted from the tabulation; it is believed that no significant quantities of minerals are mined in any of these areas. The statistics in these tables were derived principally from questionnaires sent, in cooperation with the United States Department of State, to the governments of each country. Supplementary sources were United States consular reports, the Imperial Institute's Statistical Summary of the Mineral Industry of the British Commonwealth and Foreign Countries, other official publications of various countries, the United Nations Statistical Yearbook, the Year Book of the American Bureau of Metal Statistics, Minerais et Metaux, business magazines, and company reports. Where official data were not available, esti-

Jan 1, 1953

By Thomas J. Peters

This report is part of the U.S. Bureau of Mines Idaho Land Assesment Program to study the mineral resources of priority roadless areas in Idaho. The results of these mineral inventories provide minerals information needed to make wise decisions regarding future land management practices, and to ensure a dependable supply of minerals at a reasonable cost. The 16,300-acre Lionhead area, studied in 1991, lies along the Montana border north of Henrys lake, 10 mi west of West Yellowstone, Montana. The study area includes much of the rugged Henrys Lake Mountains, and is largely covered with conifer forest. Several peaks are over 10,000 ft in elevation. The Lionhead area has been proposed for Wilderness. No mineral resources were identified within or near the Lionhead study area. Five prospects occur in, or within 1 mi of the area: these include 1) an intermittently used road gravel pit, 2) the Thimbleberry lateritic iron prospect, of geologic and historic interest only, 3) the Tick Heaven talc prospect, 4) the Dry Fork garnet prospect, and 5) the lynx prospect, which appears to be of historic interest only. Talc is seen only as float at the Tick Heaven prospect, but the geology is permissive of talc resources at depth. The garnet prospect, and nearby similar alluvial terrane, mainly outside the study area, appears to be the most likely setting to contain mineable resources. Examined workings include four trenches and pits in rock and one gravel pit.

Jan 1, 1992

By Steven J. Schatzel, Joseph Cervik, Gerald L. Finfinger

Gas drainage through surface bore¬holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwal..ls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole inter¬cepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain¬age during longwall mining will be essen¬tial for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European tech¬niques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982

By Joseph W. Town

The Bureau of Mines conducted studies related to SO2 air pollution to determine attritioning rates, SO2 sorption rates, and sulfur loads that could be obtained on commercial alkalized alumina sorbent pellets. Fluidized-bed attritioning rates ranged from 0.025 pct/hr for alkalized alumina with a crushing strength of 4 kg to 0.075 pct/hr for 0.5 kg crushing strength mate¬rial. Airlift attritioning rates ranged from 0.50 pct/hr for 3 kg crushing strength alkalized alumina to about 3 pct/hr for 0.5 kg material. Attritioning rates for the commercial alkalized alumina were comparable to those obtained for sorbent pellets prepared in the Bureau of Mines laboratory. Sorption rates were related to S02 concentration in flue gas, temperature, and presence of nitrogen oxides in the gas stream. Sorption rates at 300° C were 0.35 X 10-6 gS/gp/sec (grams sulfur per gram pellet per second) in 0.045 pct so, gas, 5.1 x 10-5 gS/gp/sec in 0.34 pct SO2 gas, and 65 X 10-5 gS/gp/sec in 10 pct SO2 gas. For the 0.34 pct S02 gas, sulfur loads of 0.10 gS/gp (the projected load for regeneration) were obtained in 47 min at 130° C and in 116 min at 300° C. The presence of either NO or NO2 in the 0.34 pet S02 gas increased the SO2 sorption rates 2 to 3 times at 300° C, but had no effect at 130° C.

Jan 1, 1969

By G. R. Hopkins

"A new record in fuel efficiency at petroleum refineries was achieved in 1935, when an average of only 615,000 B. t. u. was needed to refine a barrel of crude oil, compared with an average of 638,000 B. t. u. in 1934 and 829,000 B. t. u. In 1925. (See fig. 1.)Refiners have made almost uninterrupted progress in firing efficiency during the last decade although much of this gain was brought about by improved technique and greater use of heat exchangers and pipe stills, the determining factor was the trend in crude runs to stills. Most plants can increase their crude throughput materially with but small increase in fuel consumption. Consequently, in years in which crude runs have increased substantially, average requirements have declined; but in years in which crude runs have decreased, the average has tended upward. This conclusion is confirmed by figure 1, which shows that there has been but one minor exception to this rule in the last 10 years.Technical progress in fuel efficiency may be illustrated by comparing crude runs and total B. t, u. consumed. Between 1925 and 1935 crude runs to stills increased 31 percent, but the total quantity of heat required did not increase; in fact, it declined slightly.The trend of modern still construction is from shell stills, in which a large body of oil is heated, to tube stills, in which the heat comes into much closer contact with the oil. In 1935 the total capacity of operating pipe stills increased about 4 percent; this increase, though small, probably was related to the gain in average efficiency.The Increased use of heat exchangers and their role as fuel savers have been discussed in previous reports of this series. It is sufficient to say that refiners with insufficient exchange capacity added as much in 1935 as their budgets would permit."

Jan 1, 1937

The object of this program was to extend the capabilities of visual paging systems both in size and function. The system developed uses the mine pager phone line for communication, monitoring, and remote control. A central station, using a mini-computer, transmits signals by phase inversion modulation of a 16,384 Hz carrier to as many as 999 remote units. The remote unit addressed returns an echo to indicate that it is functioning and, in the case of monitor units, to convey the monitor data. Magnetically latched display discs, which can be seen from both sides when posted, are used for visual paging. Lists of the addresses of posted pages, unanswered pages, and non-echoing units are prepared by the central station computer. The system was designed to be intrinsically safe and should operate for three months on a 12-volt lantern battery.

Jan 10, 1980

By C. W. Dwiggins

The Bureau of Mines characterized the chemical and physical properties of metallo-organic materials in petroleum to determine their effect on petroleum production and refining. The structures and physical properties of porphyrins and materials that normally contain metalloporphyrins such as crude oils and asphaltenes were investigated using elemental analysis, NMR analysis, absorption spectrometry, and small-angle X-ray scattering. Petroleum fractions greatly enriched in metalloporphyrins were obtained using asphaltene precipitation, liquid extraction, and large-scale liquid-solid chromatography. Selected fractions containing porphyrins were further purified by chromatographic methods, crystallization, and demetalation followed by chromatography. Nonporphyrin metals could not be appreciably concentrated from the bulk of the asphaltene.

Jan 1, 1969