Search Documents

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The question as to whether or not the flow of water through pneumatic rock drills commonly used in this country keeps to a minimum dust disseminated into the air during drilling arose during a study of the dust-in-air conditions in Butte mines from February to July 1936 and December 1936 to June 1937 made by the Bureau of Mines in cooperation with the Anaconda Copper Mining Co., Butte, Mont, The purpose of this report is to describe the study, including some experimental work on the subject, and to give test results.ACKNOWLEDGMENTSThe help of the ventilation department of the Anaconda Copper Mining Co. in planning the study and collecting the data is gratefully acknowledged.EXPERIMENTAL CONDITIONSTests were conducted in an untimbered 6- by 8-foot crosscut in medium-hard granitic rock near the shaft station on an inactive level of one of the active Butte mines. Figure 1 shows the plan and section of the test location. Air was drawn from the shaft at the station, through the crosscut, and up through another shaft. The flow of air through the crosscut was decreased by a brattice downstream from the sampling location, so that relatively high, easily measurable dust concentrations would be obtained in the tests. Impinger samples for determing concentration of dust in the air were collected in an opening 51 inches wide, 29 inches high, and about 4o inches from the top of the rails in a wooden stopping about 16 feet downstream from the place where the test holes were drilled."

Apr 1, 1938

By G. B. Atkinson

To develop technology to help assure an ample domestic supply of zinc, the Bureau of Mines is investigating an aqueous chlorine-oxygen leaching process for treating complex sulfide concentrates. This report discusses the purification of aqueous C12-02 leaching solutions by utilizing zinc cementation to remove Cd, Co, Cu, Ni, and Pb. Additional processing of the purified solution is necessary to produce ZnC12 crystals suitable for molten-salt zinc electrowinning cells. The effects of solution temperature, reaction time, zinc dust concentration, ZnCl2 concentration, and degree of agitation on the removal of impurities were investigated for both simulated and actual leaching solutions. Zinc dust addition to a leaching solution at 30° C decreased the Cd, Cu, Ni, and Pb concentrations to acceptable levels of less than 3 mg/1 each. By increasing the solution temperature to 75° C, the cobalt content was decreased to less than 5 mg/l, an acceptable level for producing electrolytic cell-grade ZnC12. Impurity removal rates from ZnCl2 solutions are Pb>Cu=Cd>Ni>>Co. An increase in the solution temperature increases the rate of removal for these metal impurities.

Jan 1, 1982

Reduce potential for steering errors during tramming of articulated vehicles, particularly when the operator is seated to the rear of the machine pivot point and is tramming in reverse. Approach Position-sensing and feedback cylinders were applied to the steering cylinders of two S&S cleanup tractors to cause the steering-control lever to match the orientation of the vehicle sections. The vehicles were tested in two working mines. How It Works A position-sensing cylinder (see Figure 1, Item A) is attached to one of the steering cylinders in the cleanup tractor steering system. As the steering cylinder piston rod is actuated by movement of the control lever, hydraulic oil flows from the position sensing cylinder to the feedbck-cylinder (B), causing the feedback-cylinder piston and rod to move. The outside end of the rod repositions the the steering-control lever until its angular position corresponds to the orientation of the vehicle sections.

Jan 1, 1978

Improve the field-of-view into the front-right blind spot for drivers of large haulage trucks, thereby reducing the growing collision hazard in surface mines. Approach Reduce the glare problem found in the first generation fresnel lens blind area viewer design by eliminating the upward-looking section of the fresnel lens and adding a rear hood to reduce backlighting. How It Works The first generation blind area viewer was developed and in-mine tested as an aid to improved visibility for large haulage trucks. Other aids were improved left-and right-hand mirrors. Evaluations showed that a blind area viewer mounted on the right-front of the radiator deck was effective and was readily accepted by drivers. Nevertheless, because glare was a problem under certain conditions, a low-profile viewer was developed. Glare control louvers from the earlier design were kept and a backlighting glare control hood was added. The height of the hardware was reduced by eliminating the top three inches of the fresnel lens. This portion of the lens contained an upward-looking segment which originally was thought to be needed so the driver could see the horizon when he looked through the viewer and be better

Jan 1, 1982

To rapidly limit and interrupt high dc fault currents with minimal arcing in the mine atmosphere. Approach Design a dc switching sys-tem which uses a pressurized, liquid metal-filled, change-of-state device combined with a conventional interrupter and commutating switch. Direct Current Interruption Switching and interruption of large direct currents imposes severe loads on fuses, contactors, and circuit breakers in mine power systems. This problem is much more pronounced with de than with ac because of the lack of a natural current zero in dc. Dc interruption is characterized by persistent arcing that can foul contact tips and con-tribute to interrupter failures. To reduce maintenance and prolong the service life of these units, a commercially viable dc switching system has been developed by the Bureau of Mines through a research contract with the University of Pittsburgh. This system rapidly limits and interrupts high fault currents when used in combination with conventional interrupters.

Jan 1, 1983

By Ivette E. Torres

Bulk carriers, freighters, and tankers are the three classes of seagoing vessels engaged in transporting mineral commodities. However, vessels in these classes are not exclusively devoted to mineral commodity transport. Bulk carriers move considerable tonnages of agricultural products as well as crude minerals, their concentrates, mineral fertilizers, and the like. Freighters, owing to their great variety, can be devoted wholly to hauling mineral products or wholly to nonmineral goods, as well as carrying mixed mineral commodities and nonmineral commodities. They include general cargo ships, full container ships, partial container ships, roll-on/roll-offships, and barge carriers. Tankers, although largely engaged in moving crude oil and refinery products, also transport liquid chemicals, molasses, wine, liquefied natural gas, and other fluids. Although physical characteristics of vessels such as size, draft, crew requirements, type of propulsion system, ratio of gross tonnage to cargo tonnage, and fuel costs have undeniable influences on shipping industry performance, problems of and changes in the quantity and types of materials moved also significantly affect the shipping sector of the world economy, and thus have a bearing on the minerals sector of that aggregate. Unfortunately, comprehensive global data reflecting changes in these critical variables are not published.

Jan 1, 1994

By F. M. Carlson

Comparisons are made between the results of the Buckley-Leverett and Kern solutions, which describe immiscible displacement of oil by gas in a linear system and the results obtained from a less restrictive numerical model. This model takes into account the effect of compressibility of the oil and gas and the effect of allowing changes in the amount of gas in solution in the oil. These effects are best exemplified by imposing large pressure drops across the system. With these large pressure drops, comparison of the model solution with the Buckley-Leverett solution reveals that the Buckley-Leverett solution provides estimates of recoveries at breakthrough of the gas that are too low. In contrast to the model, the Kern solution predicts breakthrough recoveries that are too high. A modification to the Kern solution is presented to facilitate more accurate predictions of recovery at gas breakthrough for gas injection at pressures higher than the saturation pressure of the oil.

Jan 1, 1974

Improve the efficiency of stainless steel pickling (chemically cleaning) operations by providing the industry a quick and convenient method to estimate pickling solution behavior and to estimate recommended ranges of nitric and hydrofluoric acid concentrations for effective pickling of stainless steels. Background Iron, chromium, and nickel in stainless steels react with nitric and hydrofluoric acids during pickling. Ions of these dissolved metals complex or combine with the acid anions. When the total metal concentration reaches about, 50 grams per liter of pickling solution, the solution no longer serves its purpose and is considered spent. Knowledge of cation and anion species in these pickling solutions contributes an insight into pickling chemistry and allows estimates to be made of the most effective ranges of acid concentrations. The Bureau developed a computational model of the complex equilibrium chemistry occurring among iron, chromium, and nickel and the pickling solution. Total concentrations, in grams per liter, of nitrate, fluoride, iron, chromium, and nickel were used as input; output was 17 cation and anion molar concentrations. The model, in the form (if an equilibrium program on a mainframe computer, was used extensively to facilitate Bureau research by determining chemical complexes in numerous stainless steel pickling solutions. However, the program's availability to members of the stainless steel industry, its intended users, was limited because of lack of mainframe compatibility and the difficulty of program maintenance.

Jan 1, 1989

By Doris M. Hyde

New mineral activity focused on increased petroleum exploration activities, while the established construction-oriented minerals sector operated without substantial change from previous years. After showing a 1 % real growth in the $154 million II gross domestic product (GDP) for 1983, preliminary estimates for 1984 indicated that the same growth pattern prevailed. The negative trade balance at midyear had worsened over the negative balance for the same period in 1983. An upward trend in import costs partly reflected the impact of Mexican inflation, which made that country's goods more ex-pensive and led to increased imports from North America and Europe. On the other hand, by midyear, the reexport trade with Mexico indicated an upward climb from the 1988 low of $12.7 million.

Jan 1, 1986

By William H. Schiffbauer

This paper details the computer hardware and software integrated to provide computer-assisted control and monitoring of four different coal mining machines. The backbone of each system is a U. S. Bureau of Mines integrated distributed microcomputer control network called BOM/NET. The network provides connections for intelligent sensors and systems that provide for navigation, diagnostics, and computer control. Many different computer systems using various operating systems (including RMX I, UNIX, VXWORKS, DOS and DCX51) have been connected to the network and each have had complete network functionality. A description of the network's integration to Joy' 16CM, a Joy 14CM, a Jeffrey 102, continuous mining machines, and a custom built auger machine is provided. The networks for the Joy 16CM, the Joy 14CM, and the Jeffrey 102 have been installed and extensively tested at the Bureau's surface test facility. The Jeffrey 102 system has also been tested in a highwall coal seam. The Joy 14CM will soon be tested underground.

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 2 Program Use Instructions necessary to execute the program, after the card deck has been prepared, are summarized in the following. B 2. 1 Input Data Format Input data is supplied to the program in two ways a. By data cards that are read in after program compilation. b. By data specifications that are included within the program.

Jan 1, 1976

Determine the dust reduction capabilities of various bag valves available to the minerals processing industry. The Problem Many different types of ground mineral products are packaged into 50-and 100-lb paper bags. Although bag technology is continually improving, dust contamination from bags still remains a significant problem for workers. The greatest source of dust is the bag filling valve. Ideally, the bag filling valve should close after it fills the bag with the ground mineral product. However, the valve usually fails to close properly since some mineral product gets trapped inside the valve during filling and ejection. As a result, when the bag has been filled and falls from the fill station, a rooster-tail of product is discharged from the bag valve. As the bag hits the conveyor belt, additional product discharges from the bag valve. The dust from these sources contaminates the air inspired by the workers filling the bags as well as the work area. Dust also clings to the outside of the bag, contaminating the pallet loading station. Because the various commercial bag valves are composed of different materials, a dust analysis was performed on five of these valves to determine their dust reduction capabilities. The five valves analyzed were: standard paper, polyethylene, extended polyethylene, double trap, and foam.

Jan 1, 1986

By W. S. Sanner

A High Splint coal was carbonized in a low-temperature, fluidized-bed sys-tem to study the effects of thermal cracking on the products of decomposition. The coal was fluidized in recycle gas at 485° to 600° C, and the products were cracked at 600°, 700°, and 800° C in a bed of fluidized coke. Yields of tar, pitch, paraffins, and olefins decreased as carbonization temperature increased. Thermal cracking of the tar vapors produced the highest tar yields at 600° C, and light oil yield increased at cracking temperatures up to 700° C. At an 800° C cracking temperature, the yield of light oil decreased.

Jan 1, 1969

Enable prospective in situ leach mine operators to evaluate the economic potential of an ore body by using a user-friendly, computerized in situ copper oxide leach mining cost model. Background As part of its research on in situ leach mining technology, the Bureau of Mines produced a 5-volume contract report that mining companies can use to design an in situ mining operation for copper oxide deposits. Written for the Bureau by the Science Applications International Corporation (SAIC) in 1988, the generic design manual also contains a computerized cost model for evaluating the economic feasibility of in situ leach mining for any specific copper oxide deposit. The cost model is to be used with Volume II of the contract report. But because of certain complexities associated with running it, the Bureau found that the model could be improved by making it more user friendly. Approach The approach taken by Bureau researchers to make the original model more user friendly was to incorporate a HELP function to define input parameters, and to enable the display of output on the monitor. An accompanying handbook, U.S. Bureau of Mines Information Circular (IC) 9284, contains further details on running, the 1990 model.

Jan 1, 1991

Provide mine safety personnel, MSHA inspectors, and original-equipment manufacturers with guidelines and a check list for inspecting rollover protection structures (ROPS) being used in mining operations. The Problem ROPS are provided on mobile surface mining equipment to protect operators from such safety hazards as machine rollovers, falling objects, and collisions. However, the protective capability of a ROPS can be greatly reduced if it is damaged. Certain kinds of damage, such as hair- line cracks, corrosion, and loosened bolts, may occur as a result of normal machine use but may not be recognized as unsafe by untrained personnel. Therefore, the Bureau of Mmes designed a manual which can be used by mine personnel when inspecting ROPS equipment. The Manual The manual was prepared to help acquaint mine safety personnel and MSHA inspectors with typical ROPS deficiencies and their causes. It provides a systematic means for inspecting ROPS so that the identified deficiencies and their causes can be corrected. It is suggested that an inspection of the ROPS be conducted after every 1,000 h of equipment operation, or sooner if the structure has been subjected to any unusual loads which could cause damage, such as a rollover, highwall caving, or collision. The manual also details common deficiencies in the structure and attachment hardware which may affect the service life. The checklist, when used as instructed in the manual, provides a means for systematically inspecting the structure to ensure maximum protective capability and conformance with applicable Federal regulations.

Jan 1, 1986

Develop technology for preparing thick corrosion-resistant coatings and electroforms of iron-chromium-nickel alloys. Approach To reduce the United States' dependence upon foreign sources for supplies of strategic and critical metals such as chromium, cobalt, and nickel, new technology must be devised to conserve these valuable commodities. One approach being investigated by the Bureau of Mines is the use of a modified-aqueous-electrodeposition method to prepare thick (-25 µm), complex alloy coatings (e.g., stainless steel composition) with properties similar to the commercial alloys. An alloy coating on a low-alloy steel or carbon steel substrate would require significantly less strategic and critical metals than those contained in an equivalent mass of the commercial alloy. Coatings applied to appropriate mandrel materials make possible the preparation of intricately-shaped alloy electroforms (near-net-shape parts). As a result, the loss of valuable metals associated with machining finished products would be minimized.

Jan 1, 1986

By F. P. Haver

A procedure is described for recovering both lead and sulfur from galena flotation concentrate, comprising the following steps: (1) Aqueous oxidation of the concentrate, using ferric sulfate to convert lead sulfide to sulfate and to give elemental sulfur; (2) regeneration of the ferric sulfate by electrolysis in a diaphragm cell; (3) treatment of the leach residue with ammonium carbonate solution to change the lead to an acid-soluble form and to produce ammonium sulfate as a byproduct; (4) solution of the lead carbonate in hydro-fluosilicic acid followed by electrolysis to recover the lead as metal and regenerate the acid; and (5) extraction of the elemental sulfur from the final residue with an organic solvent. About 90 percent of the lead can be recovered by the above method as 99.9-percent-pure metal, together with two-thirds of the sulfur--half in the elemental form and half as ammonium sulfate.

Jan 1, 1970

By H. E. Powell

The mineral dressing research here reported is part of a continuing program by the Bureau of Mines to develop new or improved concentration processes for oxidized or partly oxidized lead and zinc ores. A sample of low-grade sulfide-oxide, lead-zinc ore from Jasper County, Mo., containing galena, cerussite, pyromorphite, hemimorphite, smithsonite, and sphalerite was concentrated by froth flotation and tabling to a grade of 66 percent lead. Because of the presence of a high content of slime-size values, the overall recovery of lead was limited to 64 percent at this grade. Tests to recover the zinc by froth flotation and by gravity concentration did not give satisfactory results. INTRODUCTION Since its establishment, the Rolla Metallurgy Research Center has con-ducted studies of base metals as a part of its overall program (1, 2, 3, 4, 5,6,7).3/ This research has been, and is, directed to beneficiating complex and submarginal ores, to retreating rejects from commercial installations, and to developing fundamental data.

Jan 1, 1960

By Kenneth M. Earl

The purpose of this investigation was to obtain subsurface information on the John Burdette barite-fluorite deposit, Garrard County, Ky. The deposit was intersected in each of five inclined diamond-drill hales aggregating 1,163 feet. All holes were drilled from the hanging wall of the deposit; the inclinations varied from minus 41° to minus 75°. Disseminated metallic sulfides were noted in the drill cores from holes 1, 2, 4, and 5. The deepest drilling was hole 5, which intersected the deposit at approximately 490 feet down dip. Visual inspection of the cores did not indicate mineralization of economic importance; therefore, no chemical analyses were conducted. Condensed logs of diamond-drill cores are included in this report. All drill cores were shipped to the Bureau of Mines core library in Minneapolis, Minn., for future reference,

Jan 1, 1959

By Jay F. Colinet, John A. Organiscak

In This Chapter [Which dust source to address first How much air and water are needed Keeping dust out of the walkway Moving workers upwind Dealing with the stage loader-crusher Gob and wing curtains to aid airflow The shearer-clearer system Modified support movement practices and Dust control for future longwalls ] Controlling longwall dust is not easy. Longwall production levels are high, and there are several different sources of dust to contend with. If dust levels are high, the initial effort should be devoted to finding which source is the cause. Then, efforts to reduce dust can be concentrated where they will have the most impact. To control dust at longwalls, a large amount of ventilation air and spray water must be used. The water must be sprayed correctly so as not to blow dust into the walkway. Techniques to change local airflow patterns can be helpful. The shearer-clearer, as well as gob and wing curtains, are examples of such techniques. DECIDING WHICH DUST SOURCE TO ADDRESS FIRST [If a longwall is out of compliance with dust standards, knowing where the extra dust is coming from helps to get back in compliance quickly.]

Jan 6, 2003