Search Documents

By S. W. Lambert

In this Bureau of Mines investigation, production was monitored for 1 year at over 30 coalbed gas-drainage boreholes located in Alabama, Pennsylvania, and West Virginia. Results indicate that the quality of data gathered from such wells can be improved greatly if potential problems are anticipated and prevented in the early stages of well production. Major water-monitoring problems include solids buildup, freezing, the presence of gas in surface waterlines, and improper pumping interval settings. Such problems may be avoided by incorporating in the original well design waterline filters, sand screens, separator tanks, and systems to automatically control pumping intervals. Problems related to measurement of coalbed gas flow include large quantities of water vapor contained in the gas, especially during winter months; freezing and subsequent obstruction of flow; sudden, uncontrolled release of gas pressure; and solids buildup in metering equipment. The installation of commercially available items, such as filters, separators, and insulation, and the thoughtful application of a basic knowledge of coalbed gas reservoir characteristics will prevent most production-monitoring problems.

Jan 1, 1978

Coal miners, especially roof bolter and continuous miner operators, work in a hazardous underground environment where they are often exposed to poor roof conditions. Nearly 500 rock fall injuries are reported each year, and 99% of them are caused by rocks falling from between the roof bolts. These loose rocks that injure miners are usually just a few inches thick, but on average weigh 280 pounds. NIOSH has found that most rock fall injuries can be prevented by installing roof screen during the bolting cycle. Roof screen is a sheet made of steel wires in a grid pattern. When screen is bolted up against the mine roof, it provides far more coverage than any common surface control used in the mines today. Because more mine roof is covered, there is less chance that a rock will fall and injure a miner. The facts about roof screen are shown in the new NIOSH video entitled “Make It Safer With Roof Screen.” Using extensive underground footage, the 7-minute video shows how well screen keeps loose rock from falling in difficult roof conditions. Techniques for installing screen from both outside-controlled and walk-thru roof bolting machines are shown. The video also provides safe handling tips, best practices, and information about machine technology that can greatly improve material handling. Throughout the video, a coal mine safety manager and a shift foreman talk about the tremendous difference that roof screen has made at their mines. An instructional booklet supplements the video with additional information. It presents compelling data from mines that have practically eliminated rock fall injuries with a roof screening program. Other sections of the booklet discuss in greater detail roof screen installation, tips for manual screen handling, a material handling system for roof screen, and use of the personal bolter screen, which can be easily handled by one person. Screen specification and custom ordering are described, including the sizes of screen, grid sizes, reinforcing (indicator) wires, edge cut options, and screen strength. A list of additional sources of information is also provided. Nearly every mine eventually encounters poor roof. Screen is one of the most powerful control techniques available. This new video will help make mine managers aware of screen, and it can help them in developing a roof screen installation program. It also serves as an information source and teaching tool for safety managers and trainers. The video can easily be integrated into new miner training programs or annual refresher training.

Mar 1, 2005

By Charles L. Kimbell

In 1990, the aggregate value of world international export trade in mineral commodities was estimated at more than $64 billion in current (1990) dollars, about 8.4% higher than that in 1989, but still 8.7% below the record high set in 1980. Table 8 provides a data series for the estimated value of world export trade in all mineral commodities from 1979 through 1990, as well as a breakdown of this total into fuel and nonfuel commodities. It is noteworthy that for this 1990 edition, trade data for the year of review were available in time for inclusion, whereas in previous editions, the latest available global trade data were for the year prior to the year of review. Hence, as regards trade, this edition of Minerals in the World Economy updates the 1989 edition by 2 years rather than by only 1. For this reason, it is appropriate to note that the 1989 global total value for inter-national export trade in mineral commodities was almost $596 billion, 11.1 % above the revised 1988 level of more than $536 billion, both figures expressed in current dollars for the appropriate year. Despite the considerable increase in the dollar value of mineral commodity exports, their share of total export merchandise trade declined to 19.1 % in 1990 from 19.7% in 1989. At 19.1%, this share was very near the recent year record low of 19.0% reached in 1988. The year 1990 was the fourth in a row in which the total value of world mineral commodity export trade increased.

Jan 1, 1993

By Robert F. Holub

The Bureau of Mines has evaluated four working-level radiation-measurement methods and optimized them from the inherent and statistical error standpoint. Optimization with respect to various sampling and measurement times yielded no marked improvement over the existing methods. However, when appropriate approximations are made and evaluated, these two-measurement methods can be reduced to simple formulas, eliminating a need to use nomograms. These modified methods also have improved inherent error characteristics. A new method--a combination of two existing methods--with improved inherent and statistical errors has been suggested. All the pertinent equations are given, together with the computer program, so that any two-measurement method can be readily evaluated.

Jan 1, 1980

Develop and demonstrate a lightweight material that has low thermal conductivity and that would be suitable for placement using shotcrete methods. This material could be applied in deep, hot mines where mine drifts must be insulated. Its use would decrease mine refrigeration needs and reduce energy costs.

Jan 1, 1994

By Doris M. Hyde

To a greater or lesser extent, the economies of the smaller Caribbean Island countries continued to have common problems. These included unemployment, inflation, foreign exchange shortages, trade deficits, and unstable world prices for their exports. Declining prices for petroleum provided some relief from scarce foreign exchange. Overall, the mineral sector remained stable. The Amerada Hess Corp. crude oil transshipment terminal on St. Lucia was completed during 1981. However, there were no shipments during the year. No official reason was offered for the delay in opening the terminal, but it may have been related to the world surplus of crude oil that occurred in 1981. There has been no further action on the refinery, which was to complete the island's petroleum complex. During the first half of 1981, an announcement was made that a second oil transshipment terminal would be built on St. Lucia. The report indicated that the terminal was to be financed by Saudi Arabia and include underground storage. After the original announcement, no further information was made available. This terminal, like the Hess petroleum complex, may have been temporarily postponed because of the crude oil surplus.

Jan 1, 1983

By H. H. Fields, T. W. Goodman, Joseph Cervik

The Bureau of Mines conducted research to determine the effectiveness of long holes drilled in solid virgin coal in degasifying an area of the Pitts- burgh coalbed showing that horizontal holes drilled into a virgin coalbed from the bottom of any shaft will effectively remove methane gas in commercial quantities from the Pittsburgh coalbed. The in situ pressure at a depth of 214 feet into the coalbed and the average gas and water flows from the five degasification holes were 3 lb/in2 gage and 860,000 ft3/d and 1.7 gal/min, respectively. On June 19, 1975, after 593 days of degasification, a compressor was installed and pipeline quality gas was introduced into a commercial pipeline. As of June 1, 1976, after 1,022 days of degasification, over 753 million cubic feet of gas had been drained and 117 million cubic feet of gas had been purchased by the gas company for use in the local community of Wadestown, W. Va. The gas drained to date is six times the gas estimated to be in the area subtended by the holes. Methane emissions at the working face of 1 West mains, Federal No. 2 mine has been reduced by 50 pct, proving the value of methane drainage by horizontal degasification holes drilled from shaft bottoms ahead of mining.

Jan 1, 1976

By H. V. Makar

Ferrous fractions recovered from urban refuse were tested by the U.S. Bureau of Mines, U.S. Department of the Interior, to assess their character, composition, and response to detinning. This research was conducted as part of the Bureau's efforts to conserve mineral resources through recycling. Results from laboratory and pilot tests established the technical feasibility of detinning scrap recovered from household refuse. Detinned products containing less than 0.03 percent residual tin were produced. Concentrations of other residual elements were determined and compared with those in existing commercial scrap and with proposed specifications. Studies were extended to include evaluations under commercial conditions. Preliminary tests on 5-1/2 short tons of ferrous fractions revealed the need for adequate shredding to assure optimum metal-caustic contact and minimize retention of tin-bearing rinse solution in the final baled product. The washed metal product contained 0.06 percent residual tin. Subsequent melt tests showed a yield of 91.4 percent. Based on these studies, full-scale commercial demonstrations showed that detinned bales equivalent to No. 1 bundle quality could be produced in carload quantities. Up to 5 pounds of tin per gross ton of scrap is con-currently recovered during the detinning process.

Jan 1, 1979

By James P. Ulery, Jon C. Volkwein

The U.S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on-site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography in the laboratory. These gas results were analyzed for explosibility. Coal samples from various depths were used to obtain the gas content of the coal using the modified direct method. Personal expo- sure to carbon monoxide was also monitored. The highest methane level observed was 9.55%. The levels of inert gas (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were nonexplosive. The gas content of the coal was about 0.30 cm3/g. The maximum personal time-weighted average sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for pre- venting explosions during auger mining.

Jan 1, 1993

By Henry E. Blake

The purpose of this Bureau of Mines investigation was twofold. The first phase of the work was to determine the technical and mechanical feasibility of defluorinating low-grade siliceous fluorspars on an intermediate scale by high-temperature pyrohydrolysis in a rotary kiln. The second phase was to react the liberated hydrogen fluoride (HF) offgas with alumina monohydrate to produce commercial-grade aluminum fluoride (85 percent AIF3). The two phases of the work were to be integrated into a single continuous process. Evaluation of the data shows that low-grade siliceous fluorspars can be successfully defluorinated, either in a solid or a molten state, in a gas-fired rotary kiln in the presence of water vapor at 1,250° to 1,350° C. The water produced by combustion of propane was sufficient to yield defluorinatians of 75 to 85 percent.

Jan 1, 1962

By T. C. Higgins, J. S. Malesky, J. A. O'Connor

"INTRODUCTION This circular contains the story of a stubborn mine fire of electrical origin that started on the main haulage road of No. 59 mine of the Peabody Coal Co. and illustrates that sometimes serious fires can be fought by direct attack. The story also points out that the cost of such procedure can be extremely high, and it is better, therefore, to minimize the possibility of a fire of electrical origin by suitable over-current and line-fault protection. The lives of 163 men were saved by utilizing a recently sunk air shaft near active workings as an escapeway. These men could not have reached the older openings. Also described are the rescue of 75 additional men through another air shaft, sealing of the fire, attempted extin¬guishment with carbon dioxide, and the difficulties of fighting the fire and recovering the mine.A fire occurred shortly before 12 o'clock noon, August 15, 1949, in the No. 59 mine, Peabody Coal Co., Springfield, Ill. All 257 men underground escaped to the surface. One group of 75 men was delayed from escaping for several hours after the alarm was given because smoke and fire gases were circulating in a main return airway, which intervened between their working section and one air shaft, and also in the stairway compartment of the shaft. After being supplied with universal-type gas masks, or self-rescuers, these men were conducted from the mine by members of a State mine-rescue team and other mine employees. Six nine officials were hospitalized because of exposure to carbon monoxide during fire-fighting activities; all were discharged a few days afterward. Later, while doing work incident to fighting the fire, two men were killed, and several were injured by falls of roof and rib.The fire broke out after a collision of a loaded trip with four empty mine cars on the main east haulage entry. The mine cars were jammed against the trolley wire causing a sustained electric arc that ignited the wooden mine cars and the fire spread to the timbers and coal."

Apr 1, 1950

By D. G. Kuehn

Studies were conducted by the Bureau of Mines to determine the positive ions and neutral species produced in glow discharges of gas streams containing 1.0 percent NO in helium, 29 percent dry air in helium, and 1.06 percent NO in N2, Mass spectrographic measurements were conducted for gas pressures from 2.3 to 10.0 torr and dc currents from 10 to 20 mAo Ion species observed included NO+, N2 +, O2 +, N+, and 0+ with lesser amounts of He+, He2+, and N02+. Variations in various ionic and neutral species with discharge duration were interpreted to be consistent with an electrically induced dissociation of NO to produce N2 and O2. No nitrogen oxides were observed to form in glow discharges of the helium-air mixture.

Jan 1, 1975

By D. S. DeLong, A. Giza, D. G. Fraser, V. A. Robinson, T. B. Whitmoyer, J. E. Sneckenberger

"A cotton dust animal exposure system has been modified to incorporate a microcomputer feedback loop to monitor particle concentrations. The loop's major components are a minature real-time aerosol monitor (miniram) to estimate concentrations and a microcomputer to read the miniram's data and to control a stepper motor that adjusts the amount of dilutant air mixing with respirable cotton dust. Ninety minute trials of this system indicate that the standard deviation of particle concentrations is within 0.68 Mg/m3 of the average concentration, insuring a near constant concentration of respirable dust throughout the exposure.INTRODUCTION Previous workWeyel et al. (1984) have determined that respirable cotton dust can be shaken from bulk cotton samples using acoustical energy. The particle generator designed to utilize this fact operates like a commercially available sonic sifter, but on a much larger scale.While this generator successfully resuspended trapped respirable cotton dust, the generator output concentration decreased exponentially with time. This disadvantage was solved by Frazer et al. (1986) by operating the generator with a sinusoidal voltage near the minimum resonance frequency of the generator. This adjustment enabled the generator to produce respirable cotton dust for six hours or longer.Frazer et al. (1987) utilized the modified acoustical generator to produce a cotton dust animal exposure system. The cotton dust concentrations were estimated by a miniram, a light scattering aerosol Monitor. The system operator used the miniram values to adjust the system's parameters to maintain the desired concentration level.PurposeThe objective of this study was to introduce a computerized feedback loop to the operator controlled cotton dust animal exposure system. The miniram's estimates were analyzed by a microcomputer to determine what adjustments in the flow of dilutant air were necessary to maintain the desired cotton dust concentration. These modifications were intended to improve system performance and ease the system operator's work burden."

Jan 1, 1988

By J. D. Noll

The Mine Safety and Health Administration (MSHA) has promulgated rules to limit the exposure of metal/nonmetal underground miners to diesel particulate matter (DPM). These rules have resulted in many types of control tech­nologies being implemented including diesel particulate filters (DPF). The passive type DPF is the most desirable because it requires little maintenance and it regenerates while the vehicle is operating. One problem with passive DPFs is that many vehicles cannot develop the sustained exhaust temperatures needed to initiate DPF regeneration, and thus it is required that the DPF be catalyzed to decrease the temperature needed for regeneration. In some past studies, such catalyzed filters have been shown to cause an increase in the nitrogen dioxide concentrations in the exhaust, resulting in a potential health hazard. In this study, a lightly catalyzed DPF along with a fuel-born catalyst were employed to help reduce the DPM emissions from a 980F loader used for cleanup in a stone mine. After 30 days of use, the filter continued to regenerate successfully at the exhaust temperatures generated by this loader, substantially reduced DPM concentrations emitted in the exhaust, and did not cause a measurable increase in nitrogen dioxide levels that could be attributed to the device.

Jan 1, 2009

By K. R. Farley

A simplified method for the atomic absorption determination of antimony is described. Samples are dissolved in hydrobromic acid and diluted to volume with water. Solutions can be ready for analysis in about 10 minutes and are stable for at least 24 hours. The spectral line at 231 nanometers is used, and there is no effect on absorption resulting .from the presence of any concentration of HBr. Absorbance is linear with antimony concentrations up to 120 micrograms per milliliter. Sensitivity is 1.48 micrograms per milliliter per 0.0044 absorbance. Relative errors on National Bureau of Standards Standard Reference Materials were 3 percent or less, and relative standard deviations on 12 determinations of each of three flue dust samples were 4 percent or less (95-percent confidence limit).

Jan 1, 1980

By W. E. Wallace, V. Castranova, P. Hathaway, F. H. Y. Green, E. D. Recad, V. Vallyathan, M. J. Keane

Inhaled particle contact with pulmonary surfactant in the hypophase lining pulmonary alveoli was modeled in vitro by exposing two respirable sized dusts, kaolin and silica quartz, to lecithin, a major component of pulmonary surfactant, emulsified in physiologic saline. Lecithin adsorbs to the dusts upon incubation at 37º C and suppresses their cytotoxicity as measured by pulmonary macrophage and erythrocyte assays, suggesting that pulmonary surfactant provides a defense system against prompt cell membrane lysis by inhaled dusts. Subsequent pulmonary macrophage phagocytosis and lysosomal enzyme digestion of the coated dusts was modeled in vitro by incubation with phospholipase A2 for one hour. With increasing lipase activity, silica hemolytic potential was restored to native silica levels. Kaolin was retoxified to levels far in excess of native kaolin hemolytic potential. Elution, thin layer chromatography and phosphate assay of treated dusts indicate most lecithin on silica is digested to lysolecithin and desorbed, silica retoxification being due to surface and adherent lysolecithin effects. Most lecithin on kaolin is not digested in this same time; that which is results in adherent lysolecithin which is responsible for the kaolin retoxification. Digestion with phospholipases A2 and C together produces only weakly retoxified kaolin. Results suggest that surface adsorption properties which control the adherence of prophylactic surfactant distinguish the pathogenic potentials of quartz, kaolin and mixed dust.

Jun 1, 1988

By D. J. Bauer

Solvent extraction techniques were used to determine the extraction sequence of yttrium and the rare-earth elements in an amine solvent extraction system. Single-stage extraction with Primene 81-R resulted in separation factors of 3.8 between yttrium and dysprosium and 25 between yttrium and cerium. Yttrium was concentrated in the aqueous phase. EDTA and DTPA, as aqueous phase counterextractants, enhance separation factors in mine-rare-earth sulfate systems. Yttrium separation from heavy rare-earth elements exhibits marked sensitivity to the position of yttrium in the selectivity scale of the rare-earth elements with the sequestrants. Yttrium-ytterbium separation is more effective with EDTA, whereas yttrium-dysprosium separation is more effectively increased with DTPA.

Jan 1, 1963

By J. G. Schoning

The Holmes Safety Association is an offspring of the Joseph A. Holmes Safety Association which was organized in Washington, D. C., in 1916 at a meeting of representatives of twenty-four leading mining associations connected with every branch of the United States mineral industries. The purpose of the meeting was to do honor to the memory of Joseph A. Holmes, one of the founders of the United States Bureau of Mines and its first director, whose death had occurred the year before on July 12, 1915. In deference to what was believed would have been the expressed wish of this great humanitarian and benefactor of the mineral industries, it was decided to establish a national safety organization to cover the mineral indus¬tries exclusively; out of respect for his memory and service, the organization was named the Joseph A. Holmes Safety Association. On receiving requests from several mining districts, in 1922 a number of chapters ware established in several mining States.

Jan 1, 1929

By Jerry W. Ramsey

The Bureau of Mines studied two Pennsylvania anthracites using low-temperature carbon dioxide adsorption. A modified form of the Brunauer-Emmett-Teller equation was used to calculate specific surface areas. Two mesh sizes of each anthracite were used to determine how gamma irradiation at 106 and 108 rads, both in vacuum and in the presence of air, affected the carbon dioxide surface areas. Results show that anthracites have a system of pores that are essentially all interconnected rather than isolated; that anthracites differ from one another in specific surface, which may correlate with density; and that irradiation in vacuum has no discernible effect on specific surface of anthracite, but irradiation in air does produce changes in specific surface.

Jan 1, 1966

The following are abstracts from papers presented at the 4th Symposium on Respirable Dust in the Mineral Industries and· were produced through research funding under the Generic Mineral Technology Center for Respirable Dust. Full articles appear in the proceedings published in July 1996 in Applied Occupational and Environmental Hygiene. (Volume 11, Number 7). The two addresses included in the proceedings point to the progress, prospects, problems, and perspectives on control of respirable dust and dust-related disease in the mineral industries. The symposium papers deal with respirable dust issues that are longstanding such as characterization, health effects, control of airborne coal dust, new and emerging issues such as iron toxicity, diesel particulates, and sampling. The papers were grouped into the following topics: continuous dust monitoring, encompassing the development of a fixed-site monitor that will provide continuous information on instantaneous and time-weighted respirable dust concentrations; mechanisms involved in the generation of dusts in mine environments, important for dust control at the source; characterization and control of diesel emissions (particularly diesel particulates) in mine atmospheres; mining systems effects and models; dust control in mine working faces and in milling environments; characterization of the physical, chemical mineralogical, and biological properties of the dust and their relevance to health effects and sampling; dust-lung interactions, encompassing results from several biomedical studies dealing with acute and chronic inhalation of airborne dusts and associated lung responses; the role of iron in causing lung injury; and therapeutic strategies for ·the control of pulmonary disease. All papers submitted to the organizers were peer-reviewed. In the proceedings, we have not differentiated among the platform and poster papers; rather, they have been grouped into the above topical areas. Taken together, these papers reveal significant progress in the control of dust generation, characterization of dust, understanding of dust-lung interaction, and mining and milling practices to reduce dust exposure - all essential for reducing dust-related occupational hazards at the workplace.

Jan 1, 1998