Search Documents

By Roberta L. Hudak, Ellsworth R. Spencer, Eric R. Bauer, Adam K. Smith

The National Institute for Occupational Safety and Health (NIOSH) is conducting research with the objective of preventing hearing loss in the mining industry. Longwall mining is one sector that has received considerable attention. Studies involving the monitoring of worker noise exposures, characterizing equipment sound levels and dominant noise sources, evaluating engineering noise controls, analyzing hearing protection device (HPD) effectiveness, and testing of improved sound level monitoring techniques specifically for longwall mining systems, are being conducted. The research efforts revealed that stageloader operators are the most exposed longwall workers, with the discharge end being the noisiest location along the stageloader. In addition, the studies have shown that using stationary dosimeters, coupled with observational data of the cutting cycle and worker habits, has the potential for improved monitoring of the effectiveness of engineering noise controls. To address the ineffective use of soft foam earplugs, a simplified 3-step method was developed for inserting soft foam earplugs. Results indicate a 9 dB greater attenuation after training subjects on the 3-step method. Finally, muff type HPDs are being evaluated for effects of speech intelligibility in noise. The combined results of these studies illustrates that much can and has been done to prevent noise-induced hearing loss (NIHL) in the mining industry, especially with respect to longwall mining workers. This paper presents an overview of ongoing studies, a progress report of results, and the implications for reducing worker noise exposures and preventing NIHL in longwall mining workers.

Continuous remote sensing of air speed In underground mine airways. Approach An ultrasonic technique measures a form of air turbulence which is proportional to air velocity. How It Works The stainless-steel enclosed transducer consists of a sensing head with circuitry, and a telemetry card. The sensor uses a patented ultrasonic technique to measure a form of turbulence created In the air. This turbulence, known as vortex shedding, is related to the air speed through the sensor. Air flowing past a cylindrical post creates vortices which flow down the air stream on both sides of the post. Pulses from an ultrasonic transmitter pass through the vortices to a receiver; the effect of the vortices on the pulses is a measure of air velocity. The transducer contains a telemetry card, known as an accessor, which transmits reports on air velocity through a pair of wires to a monitoring system. The accessor contains an analog-to-digital converter and digital telemetry circuitry required for computer system operation. The transducer does not contain any read-outs or alarms and air velocities are displayed by means of a centrally located

Jan 1, 1982

By Dhaval Patel, Kim Witte, Charles Vaught, Michael T. Stephenson, Steve Booth-Butterfield, Cynthia Zuckerman, Brian L. Quick

This longitudinal field study was designed to encourage Appalachian coal miners in West Virginia and Pennsylvania to engage in hearing-protection behaviors. Method: Participants were mailed postcards that featured either a positive, negative, or neutral message on the outside of the postcard and a message encouraging hearing protection behaviors on the inside. The first posttest measurement of the effectiveness of the persuasive messages was conducted about a week after the postcards were mailed. The delayed posttest measurement was conducted six weeks later. Results: Responses from 307 coal miners revealed that the positive or neutral messages generated significantly more self-reported hearing protection behaviors than the negative message. Identical results were obtained in a delayed posttest assessment of miners' self-reported hearing protection behaviors. The positive message was also more effective than either the neutral or negative message in preventing defensive mechanisms from emerging over time. Impact on Industry: Positive and neutral messages were convincingly more than negative messages in facilitating self-reported hearing protection behaviors among coal miners. Similarly, the positive messages kept defensive processes at bay. Keywords: Hearing protection; Hearing loss; Coal miners; Campaign; Messages

1. Mine drainage constitutes surface or ground water which flows from mines or mine sites and is usually characterized by concentrations of acidity or alkalinity. 2. The regional geology controlling the ground water flow pattern in conjunction with the life cycle mining plan can serve as a basis for making decisions about quality of water that can be expected to be encountered. 3. In regard to the prevention and control of acid water formation in underground coal mines, much is left undone in research and education: (A) Very little literature is available on this specific subject although much has been written on water management in underground mines. (B) Little or nothing is contained in the text books and curricula used in mining departments at colleges and universities with the result that educational offerings may be seriously deficient in these areas. 4. Prohibiting water entry into underground coal mines is the best method of preventing water pollution. Since this is not possible as mining operations are extended, preventing water or oxygen from contacting acid producing material may offer the next best alternative. 5. More emphasis is needed during the mine planning stage on steps to prevent water pollution. Such life cycle considerations as type of mining, sequence of development and spatial configuration as well as the elements of the drainage network and final network organization and extent must be considered.

Jan 1, 1970

By Hillary W. St. Clair

The effective coefficient for rate of reduction of a sample of granular iron ore may be determined by passing the reducing gas through a bed of the are at constant flow rate and periodically analyzing the effluent gas, The method of analyzing the data is based on a mathematical model that takes into account the variation in composition of the gas and solids with time and position in the bed. A method is described for determining the value of the rate coefficient that gives best agreement between the observed and calculated analyses of the effluent gas.

Jan 1, 1967

Reduce the number of conveyor-related accidents in the mining industry by providing recommendations for effective operation of conveyor belt cleaning systems. The Problem Troughed belt conveyors provide effective, and efficient materials transport and their use has increased throughout the mining industry. Carryback, the spillage that accumulates under the belt, is a problem even with belt cleaning systems installed. Mining personnel are exposed to safety and health hazard; as they attempt to clean up this spillage. Approach To investigate the influence of metal-segmented-blade belt cleaners on the amount of carryback spillage, the. Bureau identified and tested the following parameters: (1) amount of pressure applied to the cleaner blades, (2) friction between the blades and conveyor belt, and (3) wear rates of different metal blades. The test parameters were quantified by recording the amount of carryback material passing the metal cleaner blade, and the weight loss of the blades. The data collected were used to identify the following critic d operational parameters of a segmented-blade conveyor cleaner system: (1) the existence of an optimal operating pressure for the conveyor and cleaning systems and (2) elimination of recessed patterns on the working side of the conveyor belt.

Jan 1, 1989

Reduce costs of surface mine reclamation by improving bulldozer operating efficiency. Approach A draft power indicating system helps bulldozer operators adjust blade height and other controls for maximum load movement, by continuously indicating the rate at which work is being done. How It Works This system continuously measures both the push of the blade against the overburden, and the true ground velocity of the bulldozer. It multiplies those quantities to determine the real work rate of the machine. The system consists of a velocity sensor, a blade load sensor, processing circuits, and a work-rate indicator. The processing circuits include an analog multiplier which has an output signal representing the draft power (velocity x load = power). The draft power, or pushing power is a measurement of the work rate at that moment.

Jan 1, 1979

By J. M. Singer

Approximate equations were used to compute the radiant heating of float coal dust by approaching flames for various combinations of particle size, dust path length (flame travel distance), flame temperature, dust concentration, flame speed, and flame length. The computed values of degree of radiant heating and flame travel distance for preheating the coal dust should be useful for estimating the increased fire hazard of different coal dust-flame parameters. Some findings relating to coal mine disaster control are-- 1. Coal dust clouds cannot be preheated to ignition temperatures by flame radiation alone when deflagration speeds are greater than about 10 m/sec. Thus it appears unlikely that radiation alone will cause flames propagating in dust clouds to accelerate to detonation velocities. 2. Small particles in the radiation flame zone caused by burnout and soot formation increase the degree of preheat significantly. 3. The concentration of float coal dust (radii = 3 to 40 microns) for maximum radiant heating usually peaks in the range 50 to 200 mg/liter of air.

Jan 1, 1970

To quickly and more reliably measure the alignment and deflection of mine guides used to run skips and cages into a mine shaft. The Problem Conventional mine guide alignment measuring systems require the use of a plumb bob and tape measure. This method is not only laborious, but it is time consuming as well. Approach Aware of the drawbacks of the current measuring method, the Bureau of Mines designed a self-contained instrument system that can accurately perform vertical guide alignment and deflection measurements by remote control. How It Works The Bureau-developed instrumentation system, called the Guide Alignment Measuring System (GAMS), is based on conventional mechanical electronics using inclinometers and displacement transducers. The instrumentation system is attached to an operating skip or cage where it functions as a completely self-contained measurement system, operating in conjunction with nor-mal travel of the skip or cage. An on-board tape recorder or a mini-computer with memory can be used to record all telemetry.

Jan 1, 1987

Develop a user-friendly computer program that permits those interested in mine health and safety to access and analyze on a personal computer (PC) employment, production, and accident data for U.S. coal and metal-nonmetal mines. This software is being designed with a major focus on flexibility and case of use. The Mine Accident Decision Support System (MADSS) will be available for distribution in mid-1994. Currently, the U.S. Bureau of Mines (USBM) is seeking volunteers willing to pilot test a preliminary version of the software and to provide suggestions for its improvement. Background Since 1975, the Mine Safety and Health Administration (MSHA) has compiled large data bases of information about U.S. mines and the reportable accidents, injuries, and illnesses that have occurred in those mines. Employment and production data arc collected on a quarterly basis from each mine and accident information is collected on an incident -by-incident basis. The USBM has compiled estimated costs for each of these accidents using computer models. All of this information is potentially useful to mine health and safety researchers. However, it has been underutilized because it is stored in large mainframe data bases that arc inaccessible to many users and/or are cumbersome and difficult to use.

Jan 1, 1993

By Stephen C. Tadolini, Thomas M. Barczak

Roof support systems, longwall shields in particular, have persistently grown in size and capacity for the past 25 years. Why is this? Is it a good thing or is it unnecessary? What are the consequences of this “bigger-the-better” design philosophy? Rarely do we see a “one size fits all” approach to roof support except when it comes to longwall shields, where the historical trend for new procurements is to simply purchase the highest capacity support you can buy. Does high capacity ensure failures will not occur? The answer is no! The highest capacity tailgate supports are typically the ones that fail the most often. What does this tell us? It tells us that there are fundamental aspects of support design and ground control that we still do not understand or recognize when designing a support system. This paper provides an interesting evaluation of these issues and proposes a different approach to support design that attempts to match the support performance characteristics to the ground behavior. Along the way, some of the old premises of support design will be discarded, and new “controversial” ideas developed. Thinking outside the box never hurt any industry. Mining has made it a common practice.

By Richard V. Ageton

"Everyone admits that there are more accidents in metal mines than there should be but there is much difference of opinion as to the causes of accidents, whether avoidable or unavoidable, and the amount of responsibility attaching to the miner and the mine operator, respectively. However, it seems that one of the main reasons why there are so many accidents, is that there is so little general knowledge regarding their causes and costs. Some information regarding the costs and causes of metal-mine accidents is presented in this paper.The data contained were obtained from a study of the complete accident and medical reports of two large metal-mining companies, which carry their own insurance. Path maintain hospitals with competent medical attendants. One of these companies also maintains a very efficient safety bureau, consisting of a safety engineer, with two assistants who work in connection with the medical department, and with the safety committee made up from among the miners themselves.Daring the year of 1920, ""A"" Company employed approximately 900 men, and these men worked more than 270,000 shifts. There were 373 minor and major injuries, among these 900 men, hence assuming that each injured man was hurt cut once, 41 per cent of the men who worked in this mine received some kind of time-losing injury during the year. On account of these injuries the injured men lost 3731 shifts, and thus the time lost due to injuries amounted to approximately 1.4 per cent of the total number of shifts worked,"

Oct 1, 1923

By J. H. Maysilles

The Bureau of Mines is examining a variety of low-grade uranium ores because projections indicate that an appreciable percentage of future U.S. uranium production will be derived from resources containing 0.01 to 0.1 percent U308. One possible source is represented by a granitic material from Wyoming; the available samples contained 0.06 and 0.12 percent U308. Tests were conducted to explore the general leaching characteristics of this potential resource. The material responded to both acidic and alkaline leaching techniques. Conventional acid leaching extracted 93 percent of the uranium in 18 hours; the required acid addition was 50 to 100 pounds of H2S04 per ton of ore, and the oxidant addition was 3 pounds of NaCl03 per ton of ore. The acid consumption continues after maximum uranium recovery has been reached; this effect may complicate heap or in situ leaching with acidic solutions. Some variation in reagent requirements was noted between the two ore samples. Conventional carbonate leaching with strong solutions at 85° C extracted 94 percent of the uranium in 24 hours. These granitic materials also showed some response to dilute carbonate solutions, and the results suggest that the material may be chemically amenable to heap or in situ leaching with dilute carbonate solutions.

Jan 1, 1977

By B. J. Scheiner

The Bureau of Mines investigated an electrolytic technique for oxidizing ore slurried with brine to determine its effectiveness in extracting mercury from ores. Optimization experiments conducted on a 2.5-pound-mercury-per-ton ore resulted in 95 percent mercury extraction with operating conditions of 30° C, a current density of 0.5 ampere per square inch, and a treatment time of 3.5 hours. Corresponding power consumption amounted to 38 kilowatt-hours per ton of ore treated. Amenability experiments conducted on 62 different mercury ores resulted in 90 to 99 percent mercury dissolution from ores containing 0.6 to 20 pounds of mercury per ton of ore, Treatment time ranged from 1 to 7 hours in 4-to 20-percent sodium chloride solutions, and power consumption was in the range of 10 to 50 kilowatt-hours per ton of ore. Pilot mill experiments in a 100-to 200-pound-per-hour extraction plant have been in progress to quantify power and reagent requirements. These data will be reported in a subsequent publication.

Jan 1, 1973

Improve underground mine roof bolt support systems by alleviating problems associated with certain ground support systems currently being used. Approach Convert a passive resin-grouted roof bolt system into a uniform, tensionable roof bolting system. Background Resin-grouted roof bolts are one of the most common forms of ground support in U.S. underground coal mines. These support systems can be installed with a full-column of grout and be loaded with subsequent roof movements after installation. This is called a "passive" support system. An alternative to the passive support system is the mechanically-anchored, tensioned roof bolt system. This system is installed with resin grout. This system is designed to load or tension the support during installation by using a mechanical anchor, coupling, or threaded nut after the resin has properly cured. It is called an "active" support system and is used extensively for improved strata control in a laminated geologic deposition or in difficult ground conditions. To ensure that active bolts have been properly installed, the bolt loads must be checked by using a torque wrench or other suitable equipment. Unfortunately, this practice presents potential safety hazards and has limited accuracy. Laboratory and field experiments also reveal that the torque-to-tension ratio developed on active support systems can vary by 50% from bolt-to-bolt. Variations in bolt load installations can induce stress concentrations and lead to roof degradation or failure.

Jan 1, 1991

By Ann G. Kim

Methane in coal constitutes a serious hazard during mining. Draining the methane from large blocks of coal in advance of mining is an effective method of improving the safety and efficiency of coal mining. Because of the similarity of the two gases, drained methane can be recovered and added to pipeline supplies of natural gas. To effectively apply advance drainage techniques and recover drained gas, a gross estimate of the methane content of coal is necessary. Using data from previous investigations, the virgin reserves of the Pittsburgh coal in the central and southwestern parts of Washington County, Pa., are estimated at over 1.5 billion tons, with a methane content of 50 to 100 fts/ton. The Pittsburgh bed in this area of approximately 265 mi2 contains over 130 billion ft3 of methane.

Jan 1, 1974

Assist in controlling or extinguishing fires that occur in abandoned mine lands (AML) by providing a compilation of information on past fire control projects, the estimated extent of the current problem, and factors affecting the occurrence, propagation, and extinguishment of AML tires. Conventional fire control methods and their probable effectiveness are evaluated. Background Fires that occur in abandoned coal mines, waste banks, and coal outcrops constitute a serious health, safety, and environmental hazard from toxic fumes, deterioration of air quality, and subsidence. Although fires on AML occur in every coal-producing State, the severity of the problem varies, with most underground fires occurring in Kentucky, Pennsylvania, and Wyoming. Surface fires are prevalent in Kentucky, Pennsylvania, and West Virginia. Methods to extinguish or control AML fires, including excavation, fire barriers, and scaling, are generally expensive and have a relatively low probability of success (see figures 1 and 2). Bureau of Mines Study The Bureau compiled information from a variety of sources and found that the problem of AML fires is a serious one. Such fires can involve a high degree of hazard and can be difficult and costly to control. AML fires usually involve smoldering combustion in outcrops, waste banks, or abandoned mines. Given the nature of these fires, it is unlikely that the extent of the problem or the cost of solutions will decrease in the near future.

Jan 1, 1992

By C. A. Herbert

"The Bureau of Mines for a number of years has conducted experiments at its experimental mine near Bruceton, Pennsylvania, on the explosibility of coal dust, with particular reference to dust explosions in coal mines, and the knowledge so rained may well be applied to the handling of coal dust at industrial plants and elsewhere.Powdered coal is coming into use more and more as a fuel, and the dangers incident to its use should be recognized and guarded against, as a number of accidents have occurred in recent years due to ignorance of this danger or to carelessness.Within the past three years two very serious accidents, under almost identical circumstances, have occurred on the surface at two different coal mines in Southeastern Iowa, due in each case to the sudden ignition of a cloud of fine coal dust.The first accident resulted in the burning of six men, three of them fatally; the second burned eleven; three men died as a result of their burns.The mines in the Southeastern part of Iowa, where these two disasters occurred, are operating in a thin coal bed averaging about three feet in thickness, and are worked on the long-wall advancing system similar to that of Northern Illinois.The miners in this section are paid on a screened coal basis; in other words, receive no pay for the fine coal. As a result they use forks in loading the coal into the mine cars, and naturally a considerable quantity of coal is left along the roadways. Subsequently this fine coal, together with the roof rock that is taken down to give sufficient height on the roadways, is loaded into cars and dumped in piles on the surface. This roof rock is a block, oily shale and the contribution of fine coal and oil shale gives ample combustible material to thoroughly burn the rock as it is dumped."

Jul 1, 1923

Measure the leakage through individual crosscut stoppings quickly and economically so that the worst ones can be identified and repaired. (Typically 60 to 80% of the air supplied to a mine short circuits before reaching a working face.) Approach Most of the leakage through a permanent stop-ping is channeled through two windows in a temporary stopping, and air velocities through the windows are measured; leakage is determined from a formula. How It Works A temporary stopping made of plastic brattice is erected in the same cross cut as the permanent stopping, either upstream or downstream. The brattice is fastened to the roof, bottom, and ribs of the entry with spads. Normal leakage of brattice was allowed for in deriving formula, and does not effect results. For best accuracy the brattice and the stopping should be separated by a distance of one hydraulic diameter.

Jan 1, 1979

By S. D. Maksimovic

The Bureau of Mines evaluated the hydraulic stimulation of a gob-degasification borehole to determine if this procedure would aid in degasifying a longwall panel. The stimulated borehole did not degasify the longwall panel as expected either before or after mining of the panel started. It reduced the underground methane emission only 11 pct, considerably less than the reductions effected by two unstimulated boreholes in the same panel. Some probable reasons for the reduced methane flow from the hydraulically stimulated borehole are very low reservoir gas pressure, location of hydraulically stimulated zones within the grouted casing, a casing break caused by lateral shifting, possible vertical movement of rock strata during caving, grouting of a 4-inch pipe blocking three stimulated zones, plasticity of shales, and possible hole damage by swelling of water-sensitive minerals. The borehole was also located between two second-mined areas, which may have allowed partial degasification of the overburden and the coalbed in advance of mining. Finally, a period of 3 months is probably not long enough for the borehole to degasify the overburden before mining.

Jan 1, 1977