Search Documents

By J. W. Paul, A. C. Fieldner

"In cooperation with the New York and New Jersey State Bridge and Tunnel Commissions, the Bureau of Mines has just completed the construction of an experimental tunnel in the Bureau's experimental mine at Bruceton, Pa., near Pittsburgh, Pa. The purpose of this tunnel is to make a final study of the ventilation problems arising in the adequate ventilation of vehicular tunnels for automobiles and trucks, especially the 9000-foot tubes that are being designed. to handle the traffic between New York City and New Jersey under the Hudson River.Chief engineer, Clifford M. Holland, of the Tunnel Commissions has shown that there are three principal problems involved in planning the ventilation of this tunnel, namely - (1) The amount and composition of exhaust gases from motor vehicles; (2) The dilution necessary to render these exhaust gases harmless; (3) Determination of coefficients of airflow and horse-power required in ducts, bends and openings.Composition of automobile exhaust gases.The answer to the first problem was obtained by making road tests on 101 automobiles and trucks at the Pittsburgh experiment station. These machines were taken from service without any previous adjustment so that the composition and amount of the exhaust gas may be taken as representative of actual operating conditions prevailing in the tunnel. A report covering the results of these tests was submitted to the chief engineer of the Tunnel Commissions, on November 1, 1920, and 411 be published in the report of the commissions. Several papers a have also been published in the technical journals summarizing the important results as regards tunnel ventilation and also with reference to gasoline losses in present-day motor car operation due to the general use of unnecessarily rich mixtures"

Oct 1, 1921

By E. D. Gardener, Byron O. Pichard

"Methane, frequently called fire damp or marsh gas, is very well known to coal miners but to thy average gold miner it means nothing, as it is not associated generally with the rock formations in which gold is found.We have recently been conducting a study of mine air in typical gold mines on the Pacific Coast, and out of five California mines in which the air was sampled, three showed methane. Each of these three mines, referred to below as mines A, B, and C, have had accumulations great enough to be ignited. An authentic report from another California, gold mine, which has not yet been sampled, states that recently the superintendent was seriously burned by the ignition of a pocket of gas. This mine is later mentioned as mine D.Mine A is an old mine which had been abandoned for several years and permitted to fill with water. It has been unwaterad recently, and is now being developed at greater depths. During the unwatering, gas bubbles formed on the water and upon being ignited burned freely. It is reported that two men were seriously burned from accidentally igniting the gas. Samples of the bubbles on analysis showed high percentages of methane. Since the mine has been unwatered, no trouble has been experienced through gas being ignited. However, out of a total of six air samples which we took recently in scattered working places, all showed small amounts of methane, the methane content being 0.06, 0.04, 0.05, 0.04, 0.04 and 0.07 per cent, respectively. When these samples were taken methane was not suspected, but its general presence in the mine air indicates that it is being given off constantly."

Dec 1, 1921

Enhance coal mine worker safety and productivity by developing a means to control and predict coal mine mountain bumps. Approach The Bureau of Mines has been engaged in extensive research to understand coal mine mountain bumps and their effect on underground coal mining in the United States. Information was collected on the geologic conditions, mining techniques, and engineering parameters at five mountain-bump-prone mines. Although research has not yet evolved to the point where mountain bumps can be effectively predicted or controlled, such studies are invaluable for providing clues that can lead to the development of mountain bump mitigation technology. Case Study Results and Recommendations Mountain bumps in coal mines are explosions of the coalbed that violently release the strain energy stored within it into openings created by mining. Such an event is not only dangerous to mine workers, but can cause substantial amounts of damage to mine equipment, resulting in productivity loss and downtime. In a coal mine, the occurrence may cause coal to be expelled violently from the coal face or coal pillars or cause the mine floor to heave suddenly. Coal bumps are usually accompanied by a very loud noise and tremors or vibrations. Such ground failure:; usually occur in the vicinity of an active gob line in an active retreating room-and-pillar panel, or at or near the face in an advancing or retreating longwall mining panel.

Jan 1, 1989

By Richard Hammer

Various alternating current (ac) methods can localize faults in mining power cables. Several methods considered by the Bureau of Mines in this report are the Murray loop for short circuits, wherein a bridge provides proportional distance to the fault; capacitance measurements for open conductors; inductance measurements for shorted conductors; phase comparison, high speed recordings of voltage and current in the faulted state are compared with normal voltage and current with the difference being a function of impedance change and impedance change being a function of fault location; and standing wave measurements, detecting the resonance of the length of cable to a fault (either short or open). Portable capacitance bridges are presently available for the second method, and the fourth method is well developed for use on large power distribution systems. Because it utilizes pulses rather than ac, the time domain reflectometer (TDR) method of fault locating was not included in this investigation. However, a comparative evaluation between this versatile method and the Murray loop might prove advantageous in locating high resistance faults.

Jan 1, 1977

By J. F. Barkley

"In the course of the Government's Fuel Economy Survey of its own power plants, studies and tests have been made of various oil-burning equipments under power-plant boilers. There are now many types of burners being offered in the relatively limited field of power-plant use. The majority of the types used may be grouped into two general classes- those using steam to effect the atomizing of the oil, and those using mechanical means.Burners using steam have had the most prominence in this field for a long period. The mechanical atomizing type of burner successfully applied on shipboard, however, pointed to a possible betterment in land work. The vision presented itself of a burner that would need no steam for atomizing that would permit of air inlets or registers compactly arranged as a part of the entire burner, and that would only require the natural stack draft usually available in land boiler furnaces. Hence, rather recently there has been much development along this line, resulting in various types of burners.In Table 1 are grouped test items chosen from many tests showing representative analyses of the products of combustion obtained with various burners installed in various types of furnaces. In all these tests the burners were handled by experts and represent practically the best attainable for that particular arrangement. The boiler efficiencies ranged from 70% to 80%. It will be noted that the burners using steam for atomizing were able to secure slightly better 002 and less 02 without the presence of CO."

Feb 1, 1926

By William Wiehagen

This trainer?s guide is designed as a reference manual. The purpose is to offer information and examples to skills trainers to assist them in structuring training for new operators of Walk-Thru roof bolting machines. Trainers can use this manual as a resource for helping trainees learn, understand, and apply knowledge and skills. In this sense, the guide is not prescriptive. It is designed to offer information and trigger ideas on what might be done to accelerate learning to those who are new to the roof-bolting task. On-site trainers can modify this guide to fit their conditions, machines and equipment, and work procedures. They can integrate roof control plans, company policies and procedures, and operators? manuals from the manufacturers of the original equipment into this guide. Every trainee is different and will come to the job with varying levels of relevant knowledge and skills. The trainer?s decisions on where to start, how to organize the on-the-job and classroom training portions, and when and how to offer different aspects of the training will be based on (1) a pretraining assessment of the trainee?s knowledge and skills and (2) the trainer?s experience in conducting skills training. The ?Skill Check? section might be useful for deciding where training should start among miners who have underground experience but limited knowledge of roof-bolting techniques. Every job carries a learning curve and likely has a number of ?teachable moments? where significantly new knowledge and skills can be learned.

Aug 1, 2006

By B. Dimitriades

Experimental work has been done to refine and to confirm an analytical procedure by which gas-liquid chromatographic (GLC) spectra are interpreted from retention time data alone. The rationale of this spectra interpretation technique involves whether or not a given peak invariably represents the same component or component mixture; if not, what factors influence changes in peak identifications. To answer these questions, peak-identification procedures, based mainly on the use of subtractive columns, were developed and applied to interpret GLC spectra of several exhaust (and fuel) samples.

Jan 1, 1972

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

SUMMARY The objective of this program was to develop a system to extinguish coal mine fires by remote sealing of the underground passageways. The system developed had to be versatile enough to function under a wide range of operating conditions, including large variations in passageway geometry, depth of mine, water conditions, both in the mine and at the surface, and rubble in the mine passage. The system developed had to include instrumentation for the remote probing of the passageway prior to sealing, a system for sealing the mine passages, and instrumentation for remote monitoring of the quality of the seal during and after construction. These objectives were successfully achieved during this program. The remote mine sealing capability of the system was satisfactc rely demonstrated in a field test conducted at the Eastern Associated Coal Corporation Federal No. 1 Mine in Grant Town, West Virginia. The remote sealing consists of: (1) A sonar initial probing system which can operate satisfactorily even in the presence of dense smoke. The system is capable of determining both the local passageway geometry, identifying the presence of cribs and other obstructions, and the position of the borehole in the mine passage. (2) A mine sealing material system which utilizes fly ash for making the complete seal or as a bulk filler in conjunction with a urethane, froth foam, seal topping system. The choice of using fly ash alone or fly ash with foam topping depends on a number of factors, such as quality of seal desired, time available per seal, depth of borehole, passageway geometry, and water holding require¬ment. The fly ash-foam seal is a better seal, capable of sealing against a higher water head than fly ash alone. The fly ash sealing

Jan 1, 1973

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

9. Remote Sealing System Sensitivity 9. 1 Introduction In the previous sections a description of the overall system has been presented along with detailed descriptions of the equipment and techniques employed with the preliminary probing system, the seal em¬placement system and the seal checking system. In addition, the use of these subsystems in a specific mine application has been described in considerable detail. A broad range of parameters of interest was specified in the contract, as summarized in Section 1. 3. Most of these are a function of the general location; i. e. , the location of the mine, and the specific location; i. e. , the location of the boreholes. These parameters of interest include passage size, shape, depth, slope and water con¬ditions. The length, diameter and location of the boreholes within the mine passage and on the surface are critical parameters as well. A few additional parameters may affect one or more of the remote sealing subsystems. These include temperature, topography, rock and soil conditions, and underground water. While variation in these parameters will not render the system inoperative, consideration of them in the planning stages will simplify and expedite the field operation. In the following sections the effect of the various parameters on the remote sealing operation will be discussed. For clarity, the several tasks, borehole drilling and casing, preliminary probing, fly ash delivery, foam topping and seal checking, will each be considered separately.

Jan 1, 1973

By C. Özgen Karacan

Methane emissions from a longwall ventilation system are an important indicator of how much methane a particular mine is producing and how much air should be provided to keep the methane levels under statutory limits. Knowing the amount of ventilation methane emission is also important for environmental considerations and for identifying opportunities to capture and utilize the methane for energy production. Prediction of methane emissions before mining is difficult since it depends on a number of geological, geographical, and operational factors. This study proposes a principle component analysis (PCA) and artificial neural network (ANN)-based approach to predict the ventilation methane emission rates of U.S. longwall mines. Ventilation emission data obtained from 63 longwall mines in 10 states for the years between 1985 and 2005 were combined with corresponding coalbed properties, geographical information, and longwall operation parameters. The compiled database resulted in 17 parameters that potentially impacted emissions. PCA was used to determine those variables that most influenced ventilation emissions and were considered for further predictive modeling using ANN. Different combinations of variables in the data set and network structures were used for network training and testing to achieve minimum mean square errors and high correlations between measurements and predictions. The resultant ANN model using nine main input variables was superior to multilinear and second-order non-linear models for predicting the new data. The ANN model predicted methane emissions with high accuracy. It is concluded that the model can be used as a predictive tool since it includes those factors that influence longwall ventilation emission rates.

By Verne E. Hooker

Stress relief measurements were made at three underground test sites associated with the Henderson project, American Metal Climax, located in the rugged, mountainous region between Loveland Pass and Berthoud Pass on the Continental Divide in Colorado. Sufficient data were obtained to determine the three-dimensional stress ellipsoid for each site. The measurements were made at hole depths greater than one diameter of the mined opening; thus, calculated stresses are representative of premining in situ conditions. The vertical components of stress are in good agreement with overburden depth including the influence of mountain topography. Horizontal components of stress substantially increase with depth. These components are believed to be influenced by stresses presumably of tectonic origin. The largest measured principal stress was 5,900 psi at a depth of 3.708 feet. The predominant orientation of maximum principal stress for the determinations at greatest depth is in the NW-SE quadrants.

Jan 1, 1972

"""Hazard"" is the general expression used by safety engineers to denote risk, or the danger to property or human beings from the contingencies peculiar to different industries. Where a business, family, or individual is subjected to possible financial loss from any particular hazard, it is customary and is considered good practice to insure for reimbursement of possible loss. Accordingly, we take out insurance for earthquakes, for fire, for accidents, etc., and are charged a different premium for each. The premium rate is based on our relative exposure to the hazard in comparison to the total loss to our particular class of business in our geographical location over a given period.Insurance, then, must be considered as the experience of a group rather than of an individual, and any individual may be fortunate or unfortunate over stated periods. Through the law of averages, the probability of loss because of exposure to hazard is becoming more accurately measured as experience is accumulated and data are analyzed.Lion human life came to have a financial value in the eyes of the law, and employers were held liable for losses through accidents to employees while on duty, insurance companies began to underwrite the accident risks of the different employers and divided them into classes based on the amount of risk involved. Premiums for compensation insurance are based on relative exposure, which is measured by pay roll. The premium is rated in proportion to the severity of losses established by statistical studies.' It soon became evident that the accident experience of employers in the some industry varied widely; that is, there were good and bad risked in the same line of business. This resulted in ""experience rating"" of premiums, meaning thereby that an employer with experience in accident cost was premium rated in proportion to his losses over a stated period (usually three or more years)."

Feb 1, 1926

By Ronald S. Conti

This is the fourth and final article in a series that discusses underground fire-fighting preparedness. As with the previous three articles, it is based on interviews with 214 miners at 7 underground coal mines (referred to as Mines ?A? through ?G?) conducted by researchers of the National Institute for Occupational Safety and Health?s(NIOSH) Pittsburgh Research Center[Vaught et al. 1996]. The first article presented an overview of the study conducted by NIOSH on mine fire response preparedness and provided a general perspective on underground mine fires. The second article discussed miners? preparedness to evacuate a fire and their experience with incipient fires. The third article described miners? experiences in fighting underground mine fires and presented their perceptions of training and readiness for fire-fighting. This final article in the series offers suggestions to improve mine fire-fighting preparedness.

Jan 1, 1997

By S. E. Khalafalla

The extremely sluggish oxidation of steel scrap was appreciably accelerated when the charge was pretreated in aqueous solutions of sodium metavanadate or sodium molybdate. The degree of oxidation acceleration was inversely correlated with the melting point of the promoter oxide possessing the highest valency. The magnitude of oxidation enhancement exhibited a systematic inverse dependence on the duration of pickling processes; mere dipping of the oxidizable charge in the vanadate bath was most effective. In general, the rate of steel scrap oxidation increased with increasing concentration of the pickling reagent. The results are explained on the basis of the hydrolytic decomposition of the pickling agent with subsequent slow interaction with the metal surface, coupled with the tendency of vanadium to form polyanions in alkaline media. The data not only served to elucidate the mechanism by which catastrophic oxidation takes place, but also showed that the accelerating species need not be alloyed with the oxidizable metal; surface impregnation by minute amounts of the accelerating species can still produce catastrophic effects.

Jan 1, 1970

By Marvin L. Whisman

A radiotracer technique developed by the Bureau of Mines extends to the parts-per-billion range the sensitivity for determining contributors of deposits formed in stored and thermally stressed jet fuels. The method depends upon measuring radioactivity associated with thermally induced deposits from fuels containing one labeled compound. The technique was applied to 88 test blends, representing 12 fuels and nine carbon-l4 labeled fuel constituents or fuel additives, or both. Data from results of these tests are included in this report. With this radiotracer technique, the contribution of fuel components and additives to thermally induced deposits in a variety of fuel environments was estimated before and after storage.

Jan 1, 1969

Reliably detect fires by sensing sub-micrometer-sized particles released into the air by smoldering or burning materials. Approach An extremely sensitive, ionization-type fire detector has been built that continuously draws air samples through its ionizing field and collects the ionized smoke particles downstream, thereby generating a proportional electrical output signal. (An offshoot instrument measures the size distribution and number of sub-micrometer particles in air.) How It Works Mine air to be monitored is drawn through the instrument assembly by a small pump. A pre-filter and cyclone remove dust particles and other particles larger than 0.6 micrometer diameter. The air and remaining aerosol-sized particles flow through a gastight tube which contains the detector. See diagram. Smoke and other sub-micrometer-size particles moving Into the detector, pass through an Ionizing field, and are struck by alpha particles released from radioactive source located on the axis of the tube, The alpha particles move radially outward until they strike smoke particles or molecules of air or water. When struck, a smoke particle or molecule loses an electron and becomes positively ionized.

Jan 1, 1979

By T. L. Joseph

"In the January 3 issue of Iron Trade Review, Sweetser2, in referring to the problem of coke combustibility, points out that, ""Someone should formulate a rule for the rate of flow of coke through the zone of coke combustion that now appears to be confined to a comparatively restricted volume in front of the tuyeres,"" In formulating such a rule it is necessary to distinguish clearly between combustibility, a property of the fuel, and rate of combustion, which is determined by the rate at which air is supplied to the fuel bed. The rate of carbon gasified at the tuyeres of a blast furnace is independent of coke combusti-bility. A fast-burning coke will burn in a more restricted volume than a slow-burning coke, but both types of fuel will be consumed at rates determined by the supply of oxygen,A number of the definitions of combustibility that have appeared in technical literature relate more closely to rate of combustion than to combustibility. Perrott and Kinney) have correctly defined it as follows: ""Combustibility of coke from the standpoint of its use in, the blast furnace is inversely proportional to the mean rate of gasification per unit volume of the combustion zone, assuming other factors remain constant,"" Combustibility of coke refers therefore to those properties that determine the size or extent of the combustion zone. Relative differences in these properties can be measured by the depth of the fuel bed required to convert oxygen from the air into carbon monoxide."

May 1, 1924

A construction material based on plasticized sulfur and mineral aggregate, that is superior in corrosion resistance and strength to portland cement concrete. The material can be used in the chemical, metallurgical, and fertilizer industries, and will also provide an attractive market for by-product sulfur resulting from compliance with pollution regulations. How It Is Made Sulfur concrete is thermoplastic material. Plasticized sulfur is mixed with sand and gravel aggregate heated to 375-400° F. The sulfur melts and acts as the binder or cement. The sulfur concrete is poured hot and sets at a temperature of 200° F. Full strength is attained in a few hours, compared to several days for portland cement concretes. Sulfur concrete even pours and sets in freezing weather. Although unmodified sulfur with aggregate will produce a sulfur concrete with good initial properties, it undergoes crystallographic modifications, and deteriorates with time, particularly when exposed to moisture or freeze-thaw conditions. The Bureau of Mines has developed plasticizers which, when reacted with the sulfur, give sulfur concretes with excellent moisture and freeze-thaw resistance. The plasticizers are based on mixtures of dicyclopentadlene (DCPD) and ollgomers of cyclopentadiene. About 5 percent by weight of the plasticizers is reacted with molten sui fur for several hours. The sulfur cement can be used directly or allowed to solidify for easier handling and storage.

Jan 1, 1981

Analyze variably saturated flow in mining and other environmentally sensitive settings through the use of personal computer (PC) based software. The Problem There is an increasing need for mining companies to quantify water contaminants and their migration in the unsaturated zone. New and innovative computer models are therefore necessary to more accurately assess the potential impact of mining activities on groundwater resources and the environment. Applications for unsaturated flow modeling include (1) assessment of the impact of surface or underground extraction mining on flow conditions; (2) assessment of various hydrologic designs for resource recovery, such as in heap leaching or in situ leach mining; (3) assessment of the transport of conservative nonrcactive constituents in response to migration from spoil piles, or acid mine drainage; and (4) assessment of any combination of the above to facilitate expeditious permitting for mining operations. Since the mid 1970's there has been a proliferation of mathematical models and procedures for solving unsaturated now problems; however, few of these approaches have been integrated into software for public use. Commercially available unsaturated flow software models typically are limited to a single application and have restricted approaches. For example, computer codes that solve the unsaturated flow problem based on an analytic expression arc restricted to a simple geometric shape, homogeneous and isotropic materials, and provide only information regarding pressure and flow conditions in specified wells. The variably saturated computer codes that take advantage of the finite difference or finite element approach arc often restricted to either steady state or transient solutions; utilize one specific moisture-retention relationship and moisture-dependent permeability function; do not account for hysteresis; and are used with specific hardware such as a mainframe or work station. This restricts their use because they arc hard to interface, and arc often poorly documented, support dependent, and expensive. The mining community needs a flexible, more broadly based, variably saturated fluid flow simulator for the PC-platform to more accurately predict fluid movement in the mining environment.

Jan 1, 1991

By C. M. McCulloch

Examination of several coalbeds in Walker County, Ala., Cambria, Greene, and Fayette Counties, Pa., and Raleigh and Wyoming Counties, W. Va., indicates that cleat orientations are similar throughout a vertical sequence of strata. Studies of cleat orientation were carried out in underground mines that are operating in separate coalbeds vertically above one another. The data show that over a vertical separation of 100 to 400 feet, the average difference in coal cleat orientation between mines is 04° for the face and 08° for the butt cleat. Variations of coal cleat direction between coalbeds examined in strip-mined areas show similar values. Cleat orientations measured at outcrops agree well with the directions measured underground, suggesting that the amount of vertical separation between coalbeds has little effect on the resulting differences in cleat directions. The largest variation of cleat directions between adjacent coalbeds occurs where a large horizontal distance separates two sample locations. Cleat orientations for deeper coalbeds are most reliable where the data are taken from directly above.

Jan 1, 1976