Search Documents

By L. C. Headley

Surface areas of two synthetic and three natural consolidated porous samples were obtained by the Orr low-pressure permeametry technique. The results suggest that the Orr technique is a useful substitute for the low-temperature gas adsorption (BET) method for determining the surface area of rock samples. It was more rapid than the BET method, and the surface-area values obtained were larger but agreed better with BET values than values calculated from the Kozeny-Carman equation. Efforts were unsuccessful to demonstrate the influence of channel-size distribution on pressure-flow rate curves by means of experimental data and a parallel channel model.

Jan 1, 1971

By S. J. Schatzel

In an effort to increase productivity, many longwall mining operations in the U.S. have continually increased face lengths. Unfortunately, the mining of larger panels may increase methane emissions. The National Institute for Occupational Safety and Health (NIOSH) conducted a mine safety research study to characterize and quantify the methane emissions resulting from increasing face lengths in the Pittsburgh Coal-bed. The goal of this research effort was to provide the mine operator with a method to predict the increase in methane emissions from the longer faces for incorporation of additional methane control capacity into the mine planning process, if necessary. Based on measured methane emission rates of 0.066 m3/s (140 cfm) for a 315 m (1032 ft) face, projected longwall face methane emission rates were 0.090 m3/s (191 cfm) for a 366 m (1200 ft) face, 0.106 m3/s (225 cfm) for a 426 m (1400 ft) face, and 0.124 m3/s (263 cfm) 488 m (1600 ft) face.

Jan 1, 2006

By J. N. Tomlinson

Trailing-cable splices are evaluated for moisture exclusion abilities after repeated travel over shuttle-car sheave wheels. Tests are conducted on cables with jackets made of neoprene, cholrosulphonated polyethylene (CSPE), and nitrile butadiene-polyvinyl chloride (NBR-PVC) to 50° C. The results show that some splice kits are effective as received, others are improved with minor but significant changes, and still others must be redesigned to be effective in underground applications. Laboratory results are compared with actual underground splice results. Recommendations for cable preparation prior to splicing are presented.

Jan 1, 1979

To improve the efficiency and speed of under-ground post-disaster rescue operations. The Approach: Develop a battery-powered mine-rescue vehicle designed to carry rescue crews, rescued miners, and their support equipment. How It Works: The experimental vehicle, shown below, was designed and constructed by the Mine Safety Appliances Company under contract to the Bureau of Mines. ATV Manufacturing Company and Delco Electronics were subcontractors. A rechargeable, silver-zinc battery provides power to a 3-horsepower permissible motor, the speed of which is regulated by a solid-state controller. Three wheels on each side are independently driven by a chain and mechanical trans-mission.

Jan 1, 1974

By R. H. Grau

Improving the air quality in metal/nonmetal mines is important in protecting the health of miners. Air quality can be improved in metal/nonmetal mines by developing proper ventilation techniques. Mine ventilation systems require stoppings to direct the airflow and establish pressure differentials throughout the mine. Due to their large size, stoppings in large-opening mines are cumbersome and costly to construct and maintain. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) designed and tested two novel stoppings (Super Stopping and the EZ-Up Curtain Stopping) at its Lake Lynn Laboratory (LLL). The Super Stopping is designed as a long-term permanent stopping for use in the main entries of the mine, while the EZ-Up Curtain Stopping, although very durable, is designed more for portability and ease of installation. This paper describes the design, materials, and construction methods used for these stoppings as well as their performance and durability when subjected to tests simulating actual production face blast pressures.

Jan 1, 2006

By Garrett R. Hyde

Sintered yttria and sintered dysprosia can be used to make single-component thermistors having typical thermistor geometries and operable in the temperature range 500° to 1,200° C. However, at these temperatures, instability of platinum electrodes can contribute a slight aging effect if the thermistor is kept near 1,200° C for long periods. Typical characteristics at 500° C for an yttria disk thermistor 12 mm in diameter and 2 mm thick are a resistance of 12.4 megohms and a temperature coefficient of resistance of -3.8 percent per degree C. Typical characteristics at 500° C for a dysprosia thermistor of the same dimensions are a resistance of 1.84 kohms and a temperature coefficient of resistance of -1.6 percent per degree C.

Jan 1, 1970

By P. W. Jeran, M. C. Irani, D. H. Lawhead

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976

By Jon C. Volkwein

The industrial sand industry has been exploring new techniques to reduce dust. One company was experimenting with adding water during bagging operations to the surface of the hag, and into the product as it flowed into the bag. The Bureau of Mines, using instantaneous dust sampling instruments, measured the effectiveness of three methods of adding water. Results indicated that various types of water sprays applied in carefully controlled amounts could reduce dust up to 50% at worker locations at the bagging machine and inside a railroad boxcar. This report also discusses constraints such as product handling, customer acceptance, cold weather problems, dust collector performance, and other areas.

Jan 1, 1981

By J. E. Matta

The Bureau of Mines has developed a tracer gas method for measuring leak-age through permanent mine stoppings. In this method, a temporary brattice is erected in the same entry as the leaking permanent stopping. Leakage was evaluated from concentration measurements of a tracer gas introduced into the space between the stopping and brattice. Stopping leakages ranging from 15 cfm to 265 cfm were simulated in an underground coal mine. Leakage values determined by the new method were within 10 pct of the known values.

Jan 1, 1978

By Michael A. Trevits

Mine fires can be especially perilous because toxic products can quickly spread well beyond the fire zone thereby exposing all underground miners to dangerous and deadly conditions. Since November 1998, there have been six major underground coal mine fires or explosions in the United States (Willow Creek (twice), Sanborn Creek, Loveridge No. 22, West Elk and the Jim Walter Resources No. 5 Mine). In each case, the entire mine or specific areas of the mine had to be sealed due to the build-up of dangerous gases and the fear of uncontrolled spread of the fire. Effective placement of mine seals can deprive a mine fire of oxygen and is often followed by water flooding or injection of inert gas into the affected area. When access to the fire zone is impossible because of safety reasons, airtight mine seals can be constructed, in the area of the fire, remotely from the surface through vertical boreholes. Remotely constructed mine seals are commonly made from cementitious material. Since these mine seals are typically erected blindly, it is difficult to determine if mine roof-to-floor and rib-to-rib closure has been obtained. This paper provides a review of the available materials and technology used to remotely construct mine seals through vertical boreholes.

Jan 1, 2002

By M. E. Tyrrell

Work in this investigation was undertaken by the Bureau of Mines to demonstrate how waste glass might be utilized to lower the required firing temperature and firing time of structural clay products. Mixtures of waste glass and common clays were formed by stiff-mud extrusion and fired to the temperature required to produce a body having 6 to 7 percent absorption. Substitution of glass for one-half of the clay in a red body reduced the firing temperature 500° F, which made possible a 30-percent increase in production; in a tan body, the firing temperature was reduced 400° F, which made possible a 23-percent increase in production.

Jan 1, 1972

By Stephen P. Signer

This paper presents an overview of laboratory and field tests on approximately 250 fully grouted roof bolts instrumented with strain gauges in order to study loading behavior. Laboratory work included pull tests, time-dependent tests, and shear tests. The field tests were conducted in 14 different mines extracting different commodities. However, because of the focus of this publication, only the results of tests in 9 coal mines are reported here. In the field tests, all but 14 bolts were loaded by rock movement; these 14 bolts were tested using pull gear. The variables studied included anchorage length, mechanical interlock, time-dependent behavior, shear, installation load, loading rate, and maximum load level. Such information will improve the understanding of the behavior of resin-grouted bolts, which in return will enhance the safety of miners by reducing the occurrence of rock falls. The influences of geology, overburden depth, entry width, mining-induced stresses, and bolt spacing are not described.

Jan 10, 2000

By Thomas O. Glover

Cameroon's mineral industry continued to be dominated by crude petroleum, The economic development of the country depended on the production and export of crude on. Output was estimated to be 49 million barrels in 1985 compared with 56 million barrels in 1984 and 47 million barrels in 1988. The country's only refinery consumed approximately 12% of the daily production of crude oil while operating at slightly over 50% capacity. The refinery output, however, supplied the domestic need for motor fuel and heating oils. Cameroon's economic prospects were heavily dependent on the oil sector, which bad been responsible for the recent strong growth in the economy. The country consistently sought to avoid the problems associated with an overdependence on oil and followed a relatively broad-based development strategy, using oil revenues to sustain and encourage growth in other sectors. Approximately 75% of the gross domestic product (GDP) was attributed to the mineral industry in some form. GDP growth was approximately 6.5% during 1985.

Jan 1, 1987

By Thomas R. Bur

The amplitude of the first peak of an ultrasonic pulse which has traversed the diameter of a sphere is obtained for many directions in the sphere. This amplitude is relative to an input which is held constant for all measurements on a given sphere. Since the boundary conditions, distance of travel, and the controllable experimental factors are constant for all measurements, variations in this amplitude reflect variations in the attenuation or absorption with direction. The data are plotted and contoured as an equal area projection. The attenuation symmetry is the symmetry expressed by the contour pattern. Analysis of the data from several rock types indicates that the amplitude expresses a higher percentage of anisotropy than the velocity. In most cases the attenuation symmetry appears to be of the same system as the elastic symmetry expressed by the velocity. Results are shown for three rock spheres.

Jan 1, 1969

By Todd M. Ruff

A training software package for new mine employees, called Miner Training Simulator (MTS), has been developed by researchers at the National Institute for Occupational Safety and Health. MTS is a computer-based tool that allows a trainee to enter a simulated mine and interact with his/her surroundings in order to learn basic mining concepts, safety procedures, mine layouts, and escape routes. The training simulator software and instructions for its use are described in this report. Also, each mine using the software will have different requirements with regard to safety training. To customize the simulator for these differences, an interpreted scripting language is used to define interactions between the trainee and the virtual mine and objects in it. The scripting language, called Tool Command Language, uses simple commands to control various actions in the simulation, such as sounds, safety messages, hazards, and movement of objects. The basics of the scripting language are described here, along with many examples and instructions for building a script for MTS.

Jan 6, 2001

By Fred N. Kissell

In this report the importance of diffusion in controlling the emission of methane in mines is examined. An in-situ diffusion parameter is defined and calculated for a hypothetical unfractured lump of coal in the Pittsburgh and Pocahontas No. 3 coalbeds. The values obtained are similar to those obtained with lump coal in laboratory experiments.

Jan 1, 1972

By Gordon L. Kinney

Following a year of great uncertainty, the political situation in Bangladesh improved during 1976. The major problem for Bangladesh remained the high birth rate and crowded conditions. Bangladesh had the highest population density of any agrarian country--over 80 million people in a land area of 144,000 square kilometers, 65% of which is considered arable. The Government, with considerable foreign assistance, was actively encouraging voluntary family planning, and set a growth rate target of 2% per year or less. However, even if the growth rate was reduced to the target level immediately, the population of Bangladesh would nevertheless nearly double within 20 years.

Jan 1, 1980

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTILATION NETWORK ANALYSIS

Jan 1, 1977

By Harold W. Lipper

HELIUM shipments in 1963 exceeded the volume shipped during the previous year for the 14th successive time. Shipments from Bureau of Mines plants were 627.3 million cubic feet, an increase of 5 percent over the volume shipped in 1962. Production from Bureau of Mines plants totaled 774.2 million cubic feet. The Bureau purchased 1,420 million cubic feet of helium in the helium conservation program and stored it underground for future use. Each of the five plants, financed and built by private industry for helium conservation, made deliveries during the year. Helium continued to playa key role in space, atomic energy, defense, and other research programs. Additional capacity for liquefying helium became available, and the first civilian helium-cooled nuclear-powered reactor in the United States began pre-operation testing.

Jan 1, 1964

Effective in the 1987 Minerals Yearbook, the following changes have been made: "Asphalt" has been deleted; "Greenland" is included in the "Potash" chapter; "Meerschaum" is included in the "Clays" chapter; and "Staurolite" is included in the "Abrasive Materials" chapter. QUARTZ CRYSTAL Cultured quartz crystal production increased significantly in 198?, following 2 years of reduced production. Consumption of domestic lascas as feedstock for cultured quartz crystal increased. Imports of lascas from Brazil also increased. Although no lascas was mined in the United States during the year, the domestic producer supplied material to consumers from company stockpiles. Specimen-quality natural quartz was very much in demand; quartz crystal for this application is discussed in the Gem Stone chapter.

Jan 1, 1989