Search Documents

By Basil Dimitriades

The roles of hydrocarbons and nitrogen oxides in smog formation were investigated by the Bureau of Mines. Samples of automobile exhaust with varying HC and NOx levels were irradiated in a smog chamber under conditions that resulted in smog levels similar to those observed in the atmosphere. Results were used to define the patterns that describe the dependence of a number of smog manifestations on HC and on NOx. Using these dependence data and some simplifying assumptions, estimates were made of the ranges within which HC and NOx must lie in order to obtain specified levels of air quality.

Jan 1, 1970

By V. B. Dale

This report is one of a series covering the mineral resources of the Nation. It briefly describes most of the known tungsten deposits in Gila, Yavapai, and Mohave Counties, Ariz. Many of the descriptions are taken from the reports of previous examinations by Bureau of Mines engineers, and from Defense Minerals Exploration Administration files. Where a previous examination had been made, and an inquiry disclosed that little or no work had been done since that time, pertinent information from the report was used in this paper with acknowledgment of the source. However, the majority of the descriptions is from field examinations by the author. In the past 3 years (July 1956-May 1959) only necessary annual assessment work was conducted on nearly all the properties described in this paper. There was no active mining on any of the properties examined.

Jan 1, 1961

By R. B. Schluter

Magnetite pellets were simultaneously reduced and indurated on a laboratory scale in order to determine the effects of temperature, induration time, degree of metallization, and sulfur content upon the physical and chemical properties of prereduced pellets. The reductants were commercially-pure tank gases. Among the findings were these: 1,100° C is the minimum temperature that will produce acceptably hard pellets using carbon monoxide as the reduc-ing gas. Prolonged treatment time improves the pellets' crushing strength, but the rate of improvement falls off sharply after 2 hours' induration. At 1,120° C, 75-percent metallization produces the maximum crushing strength; there was no corresponding peak at 900° or 1,050° C. Sulfur in the furnace atmosphere lowers the required induration temperature. A few tenths of 1 percent sulfur in the pellet increases the sintering rate of metallic iron in pellets by forming a liquid FeS phase that facilitates iron transfer.

Jan 1, 1968

By C. A. Hesse

The Quartz Hill Molybdenum Project, In Southeast Alaska, was the first mining project to attempt the permitting of a submarine tailings disposal system in the United States, since the passage of the National Environmental Policy Act of 1969 and the Clean Water Act of 1977. Over $20 million was spent by the project developer in baseline data gathering and In funding the preparation of the four Environmental Impact Statements and other environmental documents required at various stages of the project between 1977 and 1988. Because of the timing and a unique set of environmental, legal and regulatory requirements which applied to this project, innovative approaches were developed. This report describes those requirements and the developments, and gives a full historical account of the campaign for permitting submarine tailings disposal at Quartz Hill, until denial of the NPDES permit application by EPA in September 1 990. The extensive studies done for Quartz Hill suggested that under certain conditions the selection of submarine tailings disposal can be the overall environmentally preferred alternative for a mining project. The Quartz Hill story illustrates the complexity of the existing permitting structure and paints out the desirability of rationalization to achieve a more effective system.

Jan 1, 1993

By Donald F. Reed

In the Coastal Plain sedimentaries of northeastern Mississippi, high-alumina clays and kaolins, which are bauxitized locally to varying degrees, are found in many places along the contact between the Midway (Paleocene) and the Wilcox (Eocene) series. The trace of the contact extends from Tippah County, on the Tennessee border, south to Winston County, thence southeast to Lauderdale County, and into Alabama. Its length within Mississippi, disregarding sinuosities, is 185 miles (fig. 1). Commercial production of bauxite from the region has amounted to about 400 tons, shipped from one outcrop in Komper County. In December 1941 and January 1942, the Bureau of Mines and the Federal Geological Survey made a reconnaissance survey of the contact zone and selected the most promising areas for further study. In 1942, four areas in Benton, Union, and Pontotoc Counties were investigated by auger and rotary core drilling, and in 194, core drilling was done on five areas in Kemper, Noxubee, and Winston Counties. The present report records the work done by the. Bureau of Mines and the factual data obtained from the investigations of the nine areas in the two projects.

Jan 1, 1952

By G. G. Morgis

In carrying out the provisions as set forth by an Act of Congress (36 Stat. 369) approved May 16, 1910, effective July 1, 1910, and the amended Act of February 25, 1913, (37 Stat. 681), the Bureau of Mines, among other activities, conducts inquiries and scientific and technologic investigations concerning mining with a view to improving health conditions and increasing safety and disseminates the general information gained by these studies. Through the medium of these publications, the causes as well as the methods that have been found most satisfactory in combating undesirable conditions are brought to the attention of the mining industry. This bulletin describes health and safety reports that have been published for the period July 1, 1955, through June 30, 1961. Technical Paper 705 issued in 1948 contains a listing of all Bureau of Mines publications dealing with health and safety in the mineral and allied industries from 1910 through 1946; Bulletin 558 contains a bibliography of such reports that were issued from January 1947 through June 1955.

Jan 1, 1962

By G. W. Jones

In a previous report,6 results were given that showed the amount of natural ventilation in a manhole having a capacity of 74.l cubic feet when the number of ventilation openings in the cover was varied. from no openings to a maximum of 48. The results showed that the ventilation (air changes per day) in the manhole was proportional to the area of the openings in the cover, and also that the number or area of the openings was the factor that chiefly affected the ventilation.

Jan 1, 1937

This Bureau of Mines report describes research on methods of assuring the continued safety of mine electrical power distribution circuits through reliability and quality assessment of the protective devices, innovative inspection techniques for these devices and the circuits themselves, novel applications of trolley line circuit breakers, and computer modeling of distribution systems to determine the proper ratings for cables, power sources, and circuit protective elements. Battery charger safety is included.

Jan 1, 1979

By J. T. McLendon

As part of its research project in developing improved refractory materials for metallurgical applications, the Federal Bureau of Mines obtained hot modulus of rupture data at 1,500°,1,550°, and 1,600° C on samples of 13 refractory periclase materials produced from seawater, lake brines, and natural magnesite. The periclase samples also were characterized to establish chemical and mineralogical composition and microstructure. The results indicated that a high MgO content does not necessarily assure good hot strength and that an optimum and varying CaO-Si02 ratio exists for each individual periclase sample.

Jan 1, 1979

By Paul M. Buttermore

As part of a national canvass of water use the Bureau of Mines compiled data on water requirements in the petroleum and natural gas industries for the calendar year 1962, specifically in well drilling, secondary-recovery operations, and natural gas processing plants. Total new water use in the petroleum industry of the United States, excluding refining, was 5.3 billion barrels. Secondary-recovery operations and natural gas processing plants required about 2.5 billion barrels of new water input; each of these requirements was about eight times greater than that for well drilling. Total use, including recirculated water, was 45.3 billion barrels of which 3.4 billion barrels was consumed. The greatest use of recirculated water was for natural gas processing, amounting to 38.2 billion barrels. Projections of total water use show that by 1975, 75.4 billion barrels will be used by the petroleum industry, of which 10.2 billion barrels will be new water. By 1985, the total use requirement will be 92.8 billion barrels, of which 13.1 billion barrels will be new water.

Jan 1, 1966

By Paul M. Buttermore

As part of a national canvass of water use the Bureau of Mines compiled data on water requirements in the petroleum and natural gas industries for the calendar year 1962, specifically in well drilling, secondary-recovery operations, and natural gas processing plants. Total new water use in the petroleum industry of the United States, excluding refining, was 5.3 billion barrels. Secondary-recovery operations and natural gas processing plants required about 2.5 billion barrels of new water input; each of these requirements was about eight times greater than that for well drilling. Total use, including recirculated water, was 45.3 billion barrels of which 3.4 billion barrels was consumed. The greatest use of recirculated water was for natural gas processing, amounting to 38.2 billion barrels. Projections of total water use show that by 1975, 75.4 billion barrels will be used by the petroleum industry, of which 10.2 billion barrels will be new water. By 1985, the total use requirement will be 92.8 billion barrels, of which 13.1 billion barrels will be new water.

Jan 1, 1966

By D. A. Paice

Under the first phase of this contract as reported in the Phase I report it was determined that certain types of commercially available molded case breakers are capable of interrupting mine dc power supplies of nominally 300 volts or 600 volts rating. These circuit breakers incorporate conventional overcurrent trip units but also can be operated by means of low power signals fed to a shunt trip coil. Further development in the Phase I program produced a means whereby a discriminating circuit breaker detector unit could sense the presence of illegitimate loads on the dc electrical system and cause the circuit breaker to trip. The detector unit operated by detecting the presence of 3000 Hz currents which were generated in the illegitimate loads by means of a 12 volt, 3000 Hz signal applied to the dc system. Further development of the program has continued in Phase II with the aim of verifying the practicability of the complete discriminating circuit breaker concept and developing other types of equipments required to implement a system. These other equipments include electronic means for raising the apparent impedance of high power legitimate loads and static filters for smaller loads. The results of laboratory work and limited underground tests have been successful. This report describes the system and the tests that have been conducted on the various equipments that comprise the complete Discriminating Circuit Breaker Concept.

Jan 1, 2012

By Henry C. Meeves

The Bureau of Mines, between 1956 and 1963, examined 18 major pegmatite districts in Arizona, Colorado, New Mexico, South Dakota, Utah, and Wyoming to evaluate their content of beryllium, a material in short domestic supply that has become increasingly important to modern industry. This examination report includes the salient statistics on the production of pegmatite minerals other than quartz and feldspar; and brief descriptions of 170 specific pegmatite deposits.

Jan 1, 1966

By H. J. Sloman

Mining laws of the several coal-producing Stat e with respect to safety catches on mine cages and their testing are extremely variable and generally indefinite in scope. The most specific requirements are contained in the Coal Mining Laws of Washington,3/ as follows:

Jan 1, 1944

By L. A. Neumeier

The Bureau of Mines evaluated creep properties of Zn-Cu-Ti alloys that were annealed after finish-rolling either cold) or at 480° F (249° C). Compositions ranged up to 1.25 pct Cu and 0.36 pct Ti. Most data are for sheet annealed after finish-rolling to 92-pct total reduction. Annealing times were varied at temperatures between 320° and 560° F (160° and 293° C). For a number of the alloys, annealing after hot-rolling at 480° F affects creep properties very differently in longitudinal and transverse sheet directions. The detrimental result is that the anisotropy in creep properties between the two directions can be vastly increased. Conversely, specific annealing treatments of certain heavily cold-rolled alloys result in surprisingly low anisotropy in creep properties and the low anisotropy coincides with excellent creep resistance for both directions. Supplemental data are presented on tensile, hardness, and thermal expansion properties, and microstructures.

Jan 1, 1972

By L. J. Kane

Conventional methods for determining the size of dust suspended in a gas require that agglomerates (clusters of particles) first be broken into particles, but in evaluating industrial dust-removing equipment the size of the agglomerates as they actually exist in the gas stream is far more important. This paper presents results of an investigation by the Federal Bureau of Mines to develop methods for determining the size of dust agglomerates suspended in a gas stream. The studies are part of the Bureau's continuing research on synthetic liquid fuels. The size and size-distribution of agglomerates as they exist when the gas reaches the filter was determined by using a membrane filter in conjunction with a dust count under a microscope. A membrane filter is a cellulosic sheet about 150 microns thick containing millions of holes per square centimeter--holes of uniform diameter that run directly through the sheet without interconnection.

Jan 1, 1960

By Daniel G. DiCanio

This report describes a computer-based model for estimating the tangible costs of injuries and deaths from work-related accidents in underground coal mines. The study undertook to identify and quantify the elements of accident costs, including field visits to coal mines, insurance carriers, and public agencies. The mathematical models developed for each tangible element of accident cost are presented in Volume I -of the report. A listing of the computer programs which comprise the model and instructions for using the programs are presented in Volume II. Statistical distributions of mining family characteristics, data on 95 miners killed in underground accidents, and other basic data used to develop the model are presented in Volume III. Application of the model to a data base of 9,286 accidents which occured in underground bituminous coal mines during 1974 yielded a total of $56,900,000 in tangible costs to industry, mining families, and public agencies. Loss of income to the families of miners injured or killed in these accidents accounted for 47 percent of the total.

Jan 1, 1976

By W. M. Myers

Jet is a substance of organic origin and has been defined by the U. S. Geological Survey as a "dense black lignite, taking a good polish, and sometimes used for jewelry". Jet is characterized by the lustrous, intense black surface it displays when polished. It is due to this property that the expression "jet black" is so commonly used to imply intense blackness.

Jan 1, 1923

By Frank Parrish

History and performance data of 17 water-injection projects in Cooke and Grayson Counties in north Texas are presented for the purpose of studying and comparing operating practices and oil-recovery techniques. Water is injected into Strawn and Canyon sands of Pennsylvanian age. The principal formation flooded is the Strawn, which ranges in depth from 725 to 6,900 ft in the projects covered. Estimated ultimate recoveries range as follows: Primary, 22 to 494 bbl per acre ft; and secondary; 63 to 296 bbl per acre ft. These figures represent the following percentages of original oil in place: Primary, 10 to 46 pct; and secondary, 8 to 23 pct. Shallower projects; 725 to 1,500 ft in depth, had higher average primary and secondary recoveries than did deeper projects. Crude-oil gravity, which ranges from 20° to 45° API, was not relatable to yield of secondary recovery oil. Analysis of the data indicates that five-spot injection patterns will yield the highest percentage of oil remaining at start of flooding; that is, 28.8 pct for five-spot injection patterns, compared with 20.8 pct for line-drive patterns and 11.6 pct for random patterns. Waterflooding in this area appears to be very successful. Secondary recoveries of most projects are expected to nearly equal primary recoveries.

Jan 1, 1963

By Albert W. Deurbrouck

The percentage of coal cleaned mechanically has increased greatly in the past 30 years. This technological change in preparation methods, accompanied by mechanical innovations in most phases of coal mining, has enabled the industry to supply quality coals at competitive prices. The Bureau of Mines has contributed to this progress by conducting research on coal-preparation problems, by evaluating the performance of domestic-and foreign-made preparation equipment, and by recording advances as they occur in industrial coal-cleaning practices. The Bureau's work in this field is recorded in the more than 150 technical and scientific publications listed in this volume. These reports, published by the Bureau over the past half century, document the Nation's progress in a vitally important phase of fuel technology.

Jan 1, 1961