Search Documents

By Mathew P. Oommen, Jeffrey L. Kohler

Computer-aided loadflow and fault analyses of mine power systems are routinely conducted to ascertain system performance and also to provide information to assist in the protection and coordination of these systems. Three-winding transformers are frequently encountered in mining applications, typically at continuous miner and longwall sections where there exists a need for dual utilization voltages. These transformers are often modeled as a three-bus system neglecting the secondary to tertiary winding impedance and the effect of base changes. This paper analyzes the impact of more accurate transformer models on voltages and fault currents which are realized from loadflow and fault studies of mine power systems.

This report was prepared by Jacob Tolsma and Arnold N. Johnson of the Uniroya 1 Research Center, Wayne, New Jersey. The valuable assistance and suggestions of the project officers, Mr. Ronald D. Hill, Dr. David R. Maneval and Mr. John J. Buscavage is gratefully acknowledged. The authors are grateful to the following Uniroyal personnel: Mr. Daniel Shichman, manager of Engineering Research, and Dr. Emmanuel G. Kontos, manager of the Polymer Physics Research for their direction, encouragement and suggestions regarding the experimental work, and Mr. Mark Olson for the design of the hollow auger soil sampler. We also wish to gratefully acknowledge the efforts and contributions of ideas proposed by our consultants, Dr. Frank T. Caruccio, assistant professor of geology at State University College, New Paltz, New York, and Dr. Pa Ho Hsu, associate professor of soil chemistry, Rutgers University , New Brunswick, New Jersey.

Jan 1, 1972

By T. E. Marshall, D. R. Dolinar, T. M. Barczak, T. P. Mucho

Over a portion of the older limestone mine workings at the NIOSH Lake Lynn Laboratory, a mining health and safety research facility, a large sinkhole formed caused in part by the intersection of several tightly spaced joint sets and unusual weather conditions. The anticipated propagation of the associated roof failures threatened to encroach upon a portion of the facility’s secondary escapeway. To protect the escapeway, two cribs walls and over 80 cable bolts were installed. In addition, extensometers were installed to monitor roof movement in the escapeway. However, a large roof fall associated with the propagating roof failures in the sinkhole area partially destroyed one crib wall where the adjacent escapeway was not reinforced by cable bolts. Recent roof movement information indicates that this area is still active. Based on these measurements, steps have been taken to stabilize this portion of the escapeway. This paper discusses roof monitoring, the roof movement, the large roof fall, propagation of the roof failures, and the recent support measures undertaken to stabilize the escapeway.

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

APPENDIX C - HOISTING SYSTEMS - AVAILABLE EQUIPMENT C 1 - Introduction A survey has been made of available hoisting equipment which has applications for use in metal and non-metal mine emergency escape hoist systems. The information was gathered from a number of sources, including representatives in the USBM and MESA, mine operators, personal visits and telephone interviews with manufacturers, field visits to inspect equipment, advertisements, catalogues and indices of manufacturers. Wherever possible, technical specifications and prices were checked out with the manufacturer, or supplier. The sections on individual sub-systems and components, such as automatic control systems, winches and controls, are not intended to be all encompassing surveys. Rather a reasonable number of representative units in each category are discussed. The sample is large enough to provide a general picture of the kind of equipment available, including the abilities and limitations and a reasonable price range. The survey has been divided into six categories 1. Complete Hoisting Systems A Above ground installations B Below ground installations 2. Hoist Assemblies ^(Man-rated) 3. Hoists (not Man-rated)

Jan 1, 1976

California's coal resources are estimated to be 100 million tons, of which 50 percent is lignite, 40 percent subbituminous, and 10 percent bituminous. The occurrence of coal in California is rather limited and is restricted generally to the foothill regions of the western slopes of the Sierra Nevada Mountains. Significant quantities of coal have been mined in five areas: Ione in Amador County, Alberhill in Riverside County, Stone Canyon in Monterey County, CorralHollow in Alarneda County, and Mount Diablo in Contra Costa County. Most of the coal was rnined in the early 1900s and was used locally for fuel. Current mining operations are located in Amador County near the city of Ione. The two producing mines supply fuel to a mine-mouth co-generation power plant. The fuel coal is processed prior to burning to extract montan wax. Because California does not have primacy, coal mining in the state is regulated by the Office of Surface Mining's Albuquerque, New Mexico, Field Office.

Jan 1, 1992

To increase awareness of float coal dust explosion hazards in the mining industry.

Jan 4, 2006

To determine the effectiveness of multiple types of fire sensors for early and reliable mine fire detection. Background The National Institute for Occupational Safety and Health (NIOSH) has evaluated the effectiveness of multiple types of fire sensors for early mine fire detection and nuisance signal discrimination. Reliable early fire detection in underground mine can be hindered by false fire alarms produced by carbon monoxide (CO) and smoke particulate emissions from diesel equipment, welding, and metal-burning activities. Another false fire alarm source is the cross-interference of hydrogen (H2) produced by battery-charging operations with a CO sensor's chemical cell. Workers can learn to ignore repetitious "false" alarms associated with these emissions. This jeopardizes their safety in the event of a mine fire.

Sep 1, 2002

By H. C. Ko

As part of the Bureau of Mines effort to provide thermodynamic data for the advancement of mineral technology, the standard enthalpies of formation for ZnO?2ZnSO4 and COS04-6H20 were determined by HC1 acid solution calorimetry. The values are -550.31 ±0.28 and -641.33 ±0.15 kcal/mot, respectively.

Jan 1, 1982

By Launa G. Mallett, Charles Vaught, Kathleen M. Kowalski, Charles D. Litton, Michael J. Brnich, Ronald S. Conti, Henry P. Cole, William J. Wiehagen

How do people behave when they are trying to get out of a fire? Are escape activities different in each incident, or will most actions be predictable across events? Do persons make the same sorts of decisions whether they are responding as individuals or as group members? Because the social costs of fire-related deaths and injuries are likely to continue to rise, societal pressure for greater safety will also undoubtedly increase. There are, therefore, compelling reasons to further our understanding of action in fires. If human behavior in fire is studied scientifically and predicted according to some well-defined principles, the benefits will be significant. Design engineers could incorporate real-world findings into their plans. Equipment manufacturers could gain from insights into how their technology is actually used in fire emergencies. Safety personnel would have a better appreciation of what constitutes adequate evacuation procedures. Trainers could upgrade the content of their courses that teach escape skills. The result would be an overall improvement in the quality of fire preparedness and safety.

Jan 1, 2000

By A. Dale Marcy, Pamela L. Drake

Workers who perform routine welding tasks are potentially exposed to fume that may contain manganese. Manganese may cause respiratory problems and is implicated in causing the occurrence of Parkinson-like symptoms. In this study, a field colorimetric method for extracting and measuring manganese in welding fume was developed. The method uses ultrasonic extraction with an acidic hydrogen peroxide solution to extract welding fume collected on polyvinyl chloride filters. Commercially available pre-packaged reagents are used to produce a colored solution, created by a reaction of manganese(II) with 1-(2-pyridylazo)-2-naphthol. Absorbance measurements are then made using a portable spectrophotometer. The method detection limit and limit of quantification (LOQ) were 5.2 mg filter-1 and 17 mg filter-1, respectively, with a dynamic range up to 400 mg filter-1. When the results are above the LOQ for the colorimetric method, the manganese masses are equivalent to those measured by the International Organization for Standardization Method 15202-2, which employs a strong acid digestion and analysis using inductively coupled plasma-optical emission spectrometry.

By Joseph E. Chilton, Robert J. Timko, Charles D. Taylor

No regular monitoring of methane is required in areas of gassy coal mines outby the mining face. Methane ignitions that have occurred in mine outby areas indicate the need to provide better protection to workers. Handheld methane monitors are now used by some miners to make periodic measurements of methane at the working face. The IYONI II gas detector which is incorporated into a miner’s cap lamp and worn on a miner’s helmet can continuously provide an alarm signal whenever methane levels exceed a set level. Tests were conducted to evaluate the performance characteristics of this methane detector by measuring response times with methane gas supplied through a calibration fixture or adaptor. Other response time tests were performed with the detector in an environmental test box. Performance was also evaluated in a full scale test gallery where face methane emission and underground ventilation were simulated. Procedures for calibration by response time measurement of the IYONI II detector have been developed. In limited testing, the IYONI II detector was found to reliably detect the presence of 1 percent by volume methane.

This chapter defines light as a type of energy, and tells how different features of light are measured. It 1s important to understand the units of light measurement because they are used throughout the rest of the book. But more Important, this will help you to understand the "regs" and how to get the best out of the lighting you have available! By the time you complete this chapter, you should know what candle-power, foot-candle, and foot-lambert refer to, and you will also be able to tell why the helmet that the new miner wears appears orange to human eyes. Light that you "see" is really radiant energy that hits the retina of the eye. Radiant energy moves out from a light source much like a series of bullets from a number of machine guns being fired at the same time in all directions.

Jan 1, 1976

By Andrew Cecala

During a recent National Institute for Occupational Safety and Health field evaluation of a newly designed filtration and pressurization system for an enclosed cab of a surface drill, it was determined that the drill operator's respirable-dust exposure was significantly increased during time periods when the cab door was opened to manually guide another section of drill steel into place to achieve additional cutting depth. Although no dust cloud was visible when the door was opened to perform this task, the drill operator's exposure was documented (over a three-day test period) to be nine times higher than when the cab door was closed. Even at this higher respirable-dust concentration, the drill operator's exposure remained well below the permissible exposure limit governed by the federal dust standard; however, an alternative method is being investigated to guide the drill steel in place in order to eliminate this increased exposure. .

Jan 1, 2008

Miners, like everyone else, must be able to see well in order to work well. But simply hauling bigger and brighter lights into the mines does not necessarily produce better mine illumination. This chapter tells why. Increasing the power of the light source can create problems of portability, glare, adaptation and contrast. This chapter also discusses some ways to increase illumination by Improving the reflectability of walls, roofs and other exposed surfaces. In Chapter IV you learned that the "brightness" of a room or work area was really a matter of how much light was reflected from the walls, roof, and other surfaces. Therefore, if you want to Improve visibility you should increase the amount of reflected illumination. O HOW DOES ONE DO THAT? One way of Increasing reflected illumination would be to increase the power of the light source.

Jan 1, 1976

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 11 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY, PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2, 1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AFCUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11, 1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS OF THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION.

Jan 1, 1977

By R. C. Wang, W. M. McKewan

The behaviour of wire ropes used in mine hoisting is not well understood. In an effort to improve this understanding, the structure of round-strand wire ropes was analysed. This report provides a generalised mathematical model that completely describes the geometry of the wires. It consists of two sets of vector equations and is valid for any round-strand wire rope. One set of equations is used to trace the paths of wires that have the form of a single helix. The other is used for the paths of double helical wires. The specific model for a 33-mm 6x1 9 Seale, IWRC, right regular lay wire rope was presented as an example. The paths and the geometric properties of the wires which include the path length per lay of strand, the curvature, and the torsion were determined from this model. In future work, the model could be used to conduct stress analysis for the wires in the deformed rope at a given rope strain and also to study the effect of wear and breaking of wires on strength loss for the various round-strand wire ropes used in mine hoisting.

By Gerrit V. R. Goodman, Charles D. Taylor, Edward D. Thimons, Jay F. Colinet

The importance of controlling respirable dust and methane gas levels in underground coal mining cannot be underestimated. While respirable dust can significantly affect the occupational health of underground coal miners, methane gas accumulations pose significant safety concerns for these same workers. Water sprays and machine mounted dust scrubbers offer effective control of respirable dust exposures and methane gas accumulations. Water must not only be applied carefully to avoid dust rollback to the machine operator but must create sufficient turbulence to remove dead zones that could contain high concentrations of methane gas. While the flooded-bed dust scrubber has been generally responsible for decreased worker exposures to respirable dusts, this device has proved effective in controlling methane levels at the face. This paper reviews practical applications of water sprays and dust scrubbers to control respirable dust and methane gas on continuous miner faces.

Jan 4, 2000

By G. T. Lineberry, W. J. Wiehagen

This paper discusses a practical method for enhancing the performance of mining work crews. The method, described as the Work Crew Performance Model (WCPM), seeks to define performance variability within similar tasks of an underground work crew. Key components of the WCPM include: (I) job definition through task analyses; (2) the ranking of job elements by perceived cost consequence; (3) observational techniques to establish performance baselines; and (4) cost linkages between adherence to task procedures and measures of consequence for noncompliance. The components of this model emphasize a reliance on learning from a veteran work force and using that information to reinvest in strategies to enhance safety and efficiency. These strategies are not limited to technologic efforts but include consideration of the so-called "soft-skill technologies" aimed at reducing variability in individual performance and at effecting a continuous improvement in overall system effectiveness.

By James R. Wait

It is the purpose of this paper to review theoretical model concepts in through- the -earth transmission of electromagnetic waves. While the subject is very broad in its defined scope, we will be conscious of the specific applications to mine rescue and emergency telecommunications in coal mine environments. The plan of the paper is to outline previous theoretical efforts without attempting to attach names or organizations to the specific developments. However, we include a guide to the literature as an appendix. Without pretending to be entirely impartial we include a critique of the limitations of the available analytical models. As I see it the central problem is to calculate the steady state mutual impedance of a four-terminal network that is the black box characterizing the through-the-earth path. Problems of secondary importance include the determination of the input impedances of the two pairs of terminals and the associated transient responses. [ ]

Jan 1, 1973

By Tye J. Lasich

This project involved modeling rock masses with varying Rock Mass Rating (RMR) values to determine the degree of instability that develops around an underground opening as a function of RMR. The modeling was performed using Itasca?s UDEC distinct element software, which allows explicit modeling of blocks of rock and how they interact with each other. The analyses included three different orientations of the joint sets, four different joint spacings and three different values of joint strength, which combine for a total of 36 different combinations of model parameters. Two different modes of behavior were observed: local failure of area immediately surrounding the roof and sides of the opening, and deep-seated failure extending a large distance beyond the opening. Quantification of the size of the unstable area that developed provides numerical validation of empirical guidelines used in design of ground support and instrumented monitoring systems.

Jan 1, 2005