Search Documents

Provide a lighter, smaller apparatus for more gently supporting electrical cable as it is raised or lowered in a well as compared with the conventional method of using a winch and pulley. Approach The conventional method of running cable into a well is to use a winch to pull the cable over a pulley located at the end of a boom placed over the well. This has the disadvantages of being bulky and of placing a concentrated strain on the cable at the point where it moves over the pulley. These disadvantages are overcome by using a "Chinese finger" cable grip assembly to hold and release a multiple conductor cable.

Jan 1, 1986

By R. D. Leitch

In the course of another investigation4 during 1926 and 1927, samples of water collected from a few abandoned coal mines indicated that their drainage was usually lower in acidity than water from active mines in the same locality. In order to determine whether this condition might have a bearing on the advisability of sealing abandoned mines, a number of such mines were visited, samples of drainage were collected, and as much information as possible was obtained from officials of the mining companies and older residents of the district. The results of this work are the basis of the present report. ACKNOWLEDGMENTS The authors are indebted to E. W. Robertson, F. F. Spowart, J. H. Nagle, and W. D. Adams of the Northwest Mining & Exchange Co.; E. M. Fasset, Fred Lane, Wm. Humphreys, and Dr. T. A. Hutchison of Brockway, Pa.; C. W. Faulk of the Shawmut Mining Co.; James Hau of Kersey, Pa., and do others for information received; and to Dr, R. R. Sayers of the Bureau of Mines, under whose direction the work was conducted.

Jan 1, 1928

By D. J. Bauer

Liquid-liquid extraction techniques were investigated by the Federal Bureau of Mines for the fractionation of rare-earth solutions. Separatory funnel work using tri-n-butyl phosphate (TBP) for extracting ceric nitrate from solutions containing sulfate ion resulted in almost complete extraction. Similar tests using primary amines for splitting trivalent rare-earth pairs and fractions gave promising results. The ceric nitrate extraction procedure was scaled-up by use of pressure-bubbler equipment, a series of spray towers for extraction, washing, and stripping. In this case only 84 percent ceric nitrate extraction efficiency was achieved. This work was done using dilute sulfuric acid for stripping.

Jan 1, 1960

By R. Barany

This paper reports determinations of heats of formation (from the oxides and elements) of crystalline cadmium metasilicate and crystalline lead meta-silicate by hydrofluoric acid solution calorimetry. The results, in conjunction with known entropy values, yield free energies of formation. There are no earlier data of this type for cadmium metasilicate. The results of this investigation for lead metasilicate deviate from the literature values (which are less reliable) in the direction of increased thermodynamic stability. Both cadmium and lead metasilicate are much less thermodynamically stable with respect to their constituent oxides than are the corresponding compounds of the alkaline earth metals.

Jan 1, 1959

By Thomas H. Dubaniewicz

Thirteen miners died as a result of 2 explosions in the Jim Walter Resources No. 5 mine near Brookwood AL in September 2001. Both explosions were ignited in intake air entries, and both were probably ignited by electrical equipment. With few exceptions, permissible equipment is not required in intake air entries of US underground coal mines Researchers with the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory. studied the electrical equipment ignition sources for the Brookwood and other w disasters to develop recommendations for preventing similar disasters Adherence to National Electrical code® requirements for flexible cords installed in hazardous (classified) locations may have prevented the second massive Brookwood explosion. The 30 CFR Part 7 requirements for battery assemblies should be reevaluated, taking into consideration United Mine Workers of America recommendations and the Zone 1"increased safety" standard requirements for battery assemblies, Class 1 Division 2 or Zone 2 explosion protection techniques are recommended for intake air equipment so that they do not present a methane air ignition source under normal operation before mine power is shut down during emergencies Battery powered circuits intake air that are likely to remain energized during emergencies should be protected by more stringent protection techniques, to protect rescue/recovery personnel. Index Terms -Class 1 hazardous location, mine explosion, flexible cord, battery assembly, permissible equipment

By R. Karl Zipf

Use of Salamon's stability criterion in underground mine design can prevent the occurrence of catastrophic domino-type pillar failure. Evaluating the criterion requires computation of the local mine stiffness and knowledge of the post failure behavior of pillars. This paper summarizes the status of the practical use of this important criterion and suggests important research to improve our capabilities. Analytical and numerical methods are used to compute the local mine stiffness. Work to date in computing local mine stiffness relies mainly on elastic continuum models. Further work might investigate local mine stiffness in a discontinuous rock mass using alternative numerical methods. Existing post failure data for coal pillars are summarized, and a simple relationship for determining the postfailure modulus and stiffness of coal pillars is proposed. Little actual postfailure data for noncoal pillars are available; however, numerical models can provide an estimate of post failure stiffness. Important factors controlling postfailure stiffness of rock pillars include the postfailure modulus of the material, end conditions, and width-to-height ratio. Studies show that the nature of the failure process after strength is exceeded can be predicted with numerical models using Salamon's stability criterion; therefore, a method exists to decrease the risk of this type of catastrophic failure. However, the general lack of good data on the postfailure behavior of actual mine pillars is a major obstacle. Additional back-analyses of failed and stable case histories in conjunction with laboratory testing and numerical modeling are essential to improve our ability to apply the stability criterion.

Jan 5, 1999

Native asphalt was produced by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries Inc., Uvalde County, TX. Gilsonite, a solidified hydrocarbon, found only in Utah and Colorado, was mined by American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California), by Ziegler Chemical and Mineral Corp., and by Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) from properties in Uintah County, UT.

Jan 1, 1984

By Jack A. Touseull

The Bureau of Mines has developed a simple stereographic method of analyzing the orientation of single and intersecting planes of weakness in vertical pillars of parallel symmetry. From this method, it can be determined if planes of weakness transect the full horizontal cross section of a pillar. A major finding resulting from this method was that intersecting planes of weakness can transect the full horizontal cross section of a pillar even though the individual planes do not. This paper provides step-by-step instructions for using this method.

Jan 1, 1977

By Travis Q. Lyday

Fiji has been an independent country within the British Commonwealth of Nations since 1970. It consists of an archipelago of more than 300 islands ranging from tiny coral atolls, cays, and rugged coral limestone islets, to the larger mountainous islands of Kandavu, Taveuni, Vanua Levu, and Viti Levu of volcanic origin. The islands of Fiji straddle the 1800 meridian about 1,800 kilometers south of the Equator in the part of the southern Pacific Ocean known as Melanesia. The production of gold and silver from the Emperor Mine at Vatukoula on the island of Viti Levu, the main island of Fiji, remained Fiji's only metallic mineral producer. Mining began at the Vatukoula site in 1933, producing 124 million troy ounces of gold and 147 thousand troy ounces of silver by yearend 1985.

Jan 1, 1987

By W. F. Marshall

The Bureau of Mines conducted a series of experiments to determine the influence of exhaust rebreathing on emissions from various gasoline and diesel engines. Tests were conducted that simulated operation of engines in nonventilated spaces as well as in spaces with partially restricted ventilation. Results of these tests showed that exhaust rebreathing can have a marked effect on exhaust emissions and thus on the composition of the air in the working space. For the case of restricted ventilation, unacceptably high (greater than 50 ppm) levels of CO in the air of the working space resulted from exhaust rebreathing rates as low as 8 pct exhaust in the engine's intake. Operation in a nonventilated space resulted in highly critical CO levels (fatal in a few minutes) at times corresponding to 1 to 3 pounds of fuel consumed per 1,000 cu ft of space. Tests involving spaces of various sizes showed that volume of the air space [per se] is not important--the primary variable is fuel consumed per unit volume of air space.

Jan 1, 1973

By G. B. Atkinson

Properties of catalysts prepared from intermetallic compound precursors were investigated by the Bureau of Mines as part of its mission to decrease U.S. dependence on foreign sources for scarce catalytic materials, such as nickel, cobalt, and chromium. Methods were developed whereby catalysts with surface areas of 30 to 40 m2/g were prepared from intermetallic compounds. Activity of these catalysts for the methanation reaction and methanol synthesis was deter-mined using a fixed-bed, single-pass, flow-through reactor. Catalysts prepared from rare-earth-nickel intermetallics had specific activity for methanation that was five times greater than that of commercial catalysts and were equal to or better than commercial catalysts with regard to sulfur tolerance. Under identical reaction conditions, catalysts prepared from thorium-copper intermetallics produced more than 10 times as much methanol as a commercial low-pressure catalyst and exhibited a high degree of catalytic stability.

Jan 1, 1982

Develop a simple and practical technique to measure in situ rock mass properties for realistic design and stability evaluation of underground structures. Background The Bureau of Mines has developed basic principles and techniques to determine in situ rock mass properties including Poisson's ratio, deformation modulus, and yield and failure strengths. An instrumentation package consisting of three pressure cells is installed in a single drill hole. Cell pressure response data are acquired and used to calculate and determine the rock mass properties. How It Works A test hole of BX size (approximately 5.7 cm) or larger is drilled to the approximate depth of the measuring point. The last portion of the test hole is drilled with precision bits to EX size (approximately 3.8 cm). The instrumentation package, which consists of one 3.8-cm-diameter cylindrical pressure cell (CPC) and two 5.7-cm-diameter cement-capsulated, flat borehole pressure cells (BPC's), is then installed. A complete history of cell response to changing strata loads is acquired on a continuous basis with a chart-type hydraulic pressure recorder. From these cell pressure data, Poisson's ratios, deformation moduli, and yield and failure strengths are calculated and determined.

Jan 1, 1990

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (Volume III) contains overall employment and injury experience for coal mines-bituminous, lignite, and anthracite; coke, petroleum and natural gas; and peat and slag plants; metal and nonmetal mines; sand and gravel operations; stone quarries; metallurgical plants, including metal mills and smelters; and nonmetal mills for 1959. Volume I of the yearbook contains injury experience and employment data in the metal, non-metal, sand and gravel, slag, and quarrying industries, and the milling operations and related plants. Volume II contains the injury experience and employment data in the fuel industries--coal, coke, petroleum and natural gas, and peat. Surveys conducted by the Bureau of Mines were the source of injury and employment data used to compile the tables and furnish information for the accompanying text. Response to the surveys was voluntary except that for coal mines. The Coal Mine Safety Act requires operators of coal mines to furnish the information requested.

Jan 1, 1960

By J. P. Rider

Average production from longwall mining operations in the United States has risen from approximately 800 tons per shift in 1980 to over 4,600 metric tons per shift in 1999. Such a large increase in production has the potential to generate significantly more dust. Previous NIOSH research has shown that, on average, respirable dust levels generated by the shearer accounts for 50% of the airborne dust generated during longwall mining. Ventilating air and water are primary controls being used in an effort to reduce longwall dust levels. Longwall operators are applying more air and water than ever before and have expressed concern over reaching maximum practical limits for these controls. Full-scale laboratory tests are being conducted to evaluate the impact on shearer-generated dust levels for changes in face air velocity, water quantity at the shearer, water spray pressure, spray system design, mining height and cutting direction. Results of this research should identify the most appropriate control levels for various operating conditions. In addition, general recommended dust control practices for longwall mining will be discussed. KEYWORDS Longwall, coal dust

Apr 1, 1975

By J. A. Eisele

As part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines has studied the removal of iron from simulated aluminum nitrate leach liquors by solvent extraction. Iron must be removed from aluminum nitrate liquor produced by leaching calcined kaolinitic clay with HN03 to reduce the iron level in alumina to less than 0.02 wt-pct Fe203 for use in reduction cells. The parameters reported are for (1) extracting iron from a feed containing 1.5 g/l Fe with di(2-ethylhexyl) phosphoric acid (EHPA), (2) stripping loaded organic phase with 20-pct HCI, and (3) water washing of loaded and stripped organic phase. Recommended operating conditions are two extraction stages using 15 vol-pct EHPA in kerosene and three stripping stages using 20-pct HCI. Results are also given for tests using other extractants and stripping agents.

Jan 1, 1982

By Thomas V. Falkie, R. Venkataramani

1. Summary This investigation is concerned with description of the loading function at the underground coal face, and the identification of varia¬bles - geological, geometric, mechanical, and operational - that affect the loading function. The immediate objective of this work was to provide information for operations-research studies as applied to underground coal mining, and the broad objective was to provide guide¬lines for planning and equipment selection in underground coal mining. The loading function was expressed as -a statistically-developed linear mathematical model. Originally, fifteen independent variables were considered which potentially could have influenced the loading function. These variables were constructed on the basis of measurable or estima¬ble geometric and geological properties at the working face, mechanical characteristics of the mining machine, and certain operational proce¬dures of mining. The original model explained 64.0 percent of the experimental variation. The final condensed model explained 54.1 percent of the experimental variation in terms of only five indepen¬dent variables, namely: 1. Ratio: width of cut/total width of cutter 2. Ratio: height of cut/diameter of cutter 3. Total horsepower of cutter-drive motors 4. Rotation speed (RPM) of cutter 5,. A subjective estimate of machine quality and operator skill Certain limitations were found to exist in the evaluation of the variables. Principle among these limitations was the impossibility of precise measurement of tonnage loaded in certain instances.

Jan 1, 1972

By Lloyd A. Morley, Robert Stefanko

A major difficulty encountered during the research was that nation¬al countries (almost world-wide) are in the process of revising their electrical hazard reduction standards. Their principal goal is to align their standards with the International Electrotechnical Commission (IEC) Recommendations Publication Series 79. (31-37) Additionally, CENELEC is requiring all Common Market countries to harmonize their standards. (85) However in the coal mining industry some hazard re¬duction techniques are not being accepted because some systems may not be applicable. Therefore, past literature might not directly relate a country's current feeling about explosion-proof standards. An authority in the United Kingdom (which has been a leader in hazard reduction mainly through work at the Safety in Mines Research Establishment) brought up an additional point. (15) He hopes that since revising British standards BS229 into BS4683, with the intention of corresponding with the IEC 79 series, the recent CENELEC harmoni¬zation process will also follow IEC. (8, 9, 10) The past trend in other major Common Market countries prior to CENELEC's requirement results in the authors' speculation that the standards will be pattern¬ed after the IEC Publications. (5,17,60,84,102) Several letters were sent to the East Block countries but, disa¬ppointingly, replies were dispatched only from the USSR and Poland. Recent Polish standards (1973) were received, and a very close match to the IEC Publications has been noted. (76,77) Because of their economic community, it is extremely logical to assume that the East Block stand¬ards are therefore in concurrence with the IEC. Japanese specifications also appear to be compatible with the IEC Recommendations. (42,43)

Jan 1, 1974

By T. G. Carnahan

The Federal Bureau of Mines investigated, on a laboratory scale, a technique for recovery of silver from pregnant solutions generated in the hydro-metallurgical treatment of complex base-metal sulfide concentrates with oxidizing chloride media. This technique provides a means for recovery and simplified reduction of accessory silver to metal from chloride solutions. The method consists of adding NaI or KI to the solution to precipitate AgI, which is then contacted with Na2S to produce Ag2S and to regenerate the iodide salt solution. Silver recoveries range from 99 pct with 20 pct excess iodide precipitant, to 92 pct when the theoretical stoichiometric amount of precipitant is employed. The Ag2S product can be reduced to silver metal by contact with aluminum chips in NaOH solution followed by purification with conventional fire refining techniques.

Jan 1, 1980

By Robert L. Chufo, H. Kenneth Sacks

Medium-frequency (MF) waves can propagate in a coal seam, bounded above and below by conducting rock, in an approximate transverse electro-magnetic (TEM) transmission-line mode with the electric field vertical and the magnetic field horizontal. The theory of this coal seam mode is applied to recent MF data for a number of mines in order to classify the propagation characteristic of the mines in a simple way. When conductors such as rails, trolleylines, or power cables are present in the vicinity of the measurement path, it is found that the magnetic field versus range plots have two distinct regions with very different slopes. This effect is attributed to coupling of the cylindrically spreading coal seam mode to a low-attenuation conductor guided mode. As a result, voice communications range between mobile transmitters can extend several thousand meters. The use of MF for mine communications is discussed.

By John G. Kovac

A computer simulation has been developed by the US. Bureau of Mines to estimate the chances of a miner making a successful escape while wearing a self-contained self-rescuer (SCSR). The model takes into account (1) training in the use of SCSR's, (2) apparatus integrity, and (3) oxygen cost of a mine escape. This report examines survival odds for a prototypical escape, and illustrates how these odds change when SCSR training is improved.

Jan 1, 2009