Search Documents

By Lloyd A. Morley, Robert Stefanko

1. Anonymous (Berggewerkshaftliche Versuchsstrecke), "75 Jahre Berggewerkshaftliche Versuchsstrecke, 1894-1969," 1969. 2. Anonymous, British Symposium on Flameproofing and Intrinsic Safety, IEEE Conf. Report Series No. 3, 1962. 3. Anonymous (Ministry of Fuel and Power), "A Review of Electrical Research and Testing with Regard to Flame-Proof Enclosure and Intrinsic Safety of Electrical Apparatus and Circuits," 1943. 4. Australian Standard Specification, ASC-98, "Electrical Equipment for Explosive Atmospheres," 1970. 5. Belgium Standard Specification, Norme NBM 286, "concernant la protection par enveloppe antideflagrante," 1965. 6. Bossert, J.A., "Approval for Electrical Equipment for Hazard Locations," paper PCI 66-33, IEEE 16th Annual Petrol. and Chem. Ind. Conf., L. A., California, Sept. 15-17, 1969. 7. Bossert, J.A., "Intrinsic Safety in Canada," Electrical Safety Practices, ISA Monogram, vn. 112, 1969. ,8. British Standards, BS229, "Flameproof Enclosure of Electrical Apparatus," 1957. 9. British Standards, BS4683 Part 1, "Classification of Maximum Surface Temperatures," 1971. 10. British Standards, BS4683 Part 2, "The Construction and Testing of Flameproof Enclosures of Electrical Apparatus," 1971. 11. Brown, G.R., and Silver, S., "An Explosion Hazard Due to Inflam¬mation of Aluminum Particles in Flat Flanges of Flameproof Enclosures," CEAL No. 197, Canadian Explosive Atmospheres Labor¬atory, 1969. 12. Campbell, J.D., and Chudleigh, J.P., "Problems Encountered in Designing Electrical Systems for Hazardous Areas," paper PCI-69¬31, IEEE 16th Annual Petrol. and Chem. Ind. Conf., L. A., California, Sept. 15-17, 1969. 13. Canadian Standards Association, C22.2 No. 30, "Explosion-Proof Enclosures for Use in Class I Hazardous Locations." 14. Dainty, E.D., and Brown, G.R., "Explosion Gas Temperatures at the Entrance to Flanges of Enclosures Containing 8.5% Methane-Air Mixtures," CEAL No. 196, 1969.

Jan 1, 1974

By Edward Thimons, William A. Hertbrink

The effect of wind speed upon aerosol penetration into an idealized enclosure was studied The idealized enclosure was a painted plywood box that was 1 2X1 2 XI meters in volume Two fans supplied 1 7 m3 /min of filtered air to this enclosure at a static pressure of 2 8 mm of water The enclosure had a 7 5 cm diameter vent port which was isolated from the air flow around the enclosure To simulate holes in real enclosures, three 16-cm diameter holes were drilled on the front and back sides of the enclosure This simulated enclosure was placed in a tunnel-like structure The air flow from an ultra-light air craft was directed at the front of the enclosure The air speeds were varied between 14 and 36 km/hr as measured by rotating vane anemometer Static pressure in the enclosure was measured with an electronic manometer Two optical particle counters measured the particle number concentration of particles between the 0 35 to 0 5 µm inside and outside of the enclosure Aerosol penetration into the enclosure was computed as the ratio of the aerosol concentration inside the enclosure to the concentration outside of the enclosure The enclosure static pressures measured increase from 2 8 to 3 4 mm of water (P=00001) Aerosol penetration into the enclosure increased linearly with air velocity above 20 km/hr Theoretically estimated penetrations were correlated with observed penetration into the simulated enclosure When simple linear regression was used to model the observed penetration as a function of the estimated penetration, the value of the slope was 0 69±0 12 and the P value for the regression model was less than 0 0001 These results indicate that enclosure static pressure needs to be higher than the wind's velocity pressure in order to minimize aerosol penetration into these enclosures

Jan 1, 1999

By Charles Findlay, Stephen Krickovic

A methane emission rate study was conducted in 1969 on a longwall section of a Lower Kittanning coalbed mine in central Pennsylvania. The longwall face was mined with a drum shearer between developed headings on the head end and headings on the tail end that were driven with a ripper-type continuous miner as needed. The study was conducted over 22 consecutive shifts (7-1/3 days). The average methane emission rate from the Lower Kittanning coalbed during mining at the face and developing the headings at the tail end of the face was 34 cfm. Caving of the gassy overlying strata as the result of mining at the face increased the methane emission to rates ranging from 702 to 1,049 cfm.

Jan 1, 1971

By Maria I. De Rosa, Charles D. Litton

The National Institute for Occupational Safety and Health (NIOSH/PRL) con­ducted a series of large-scale experiments to evaluate the effectiveness and safety of various concentrations of an inert gas mixture (CO2,8%;N2, 50%; Ar, 42%) for preventing and sup­pressing cab ?res. Comparison of concentrations effectiveness in yielding safe times has led to the choice of an optimum gas mixture concentration, discharged in the cab through a muf?ed nozzle system, for the development of a dual cab ?re inerting system. Of note is that safety training programs, including the synchronization of performed tasks, need to accompany this technology to enhance operator’s ef?ciency and safety during ?re emergencies within the safe times yielded by the cab ?re inerting system. Cab ?res are caused by the ignition of ?ammable vapors and mists (ball of ?re) that penetrate the cab during prolonged hydraulic ?uid and fuel ?res, and electrical malfunctions involving other cab combustible materials. Often, these ?res force the operator to exit the cab under hazardous conditions during a time needed to perform emergency tasks. Hence, it is important to provide the operator, not only with an engine fire suppression system (dry chemical powder), but also with a cab ?re protection system, effective both in preventing the ignition of ?ammable vapors in the cab, and suppressing cab material ?res.

By E. G. Valdez

Iron foundries that melt automobile scrap produce flue dusts averaging about 32 percent zinc and 6 percent lead. Some is sold to smelters, but because of the meager return and difficulty in handling, most of the dust is discarded. As part of the Bureau of Mines program to find uses for mineral wastes, research was initiated to develop an economical process to recover zinc and lead from the flue dust. Research encompassed the extraction of zinc and lead by fuming, leaching, and agglomeration. Controlled vacuum fuming of zinc to produce Prime Western zinc and a lead-rich residue was the most effective method for treating the dust. This process involved two distillations, or fumings, with carbon and methane as reductants, and resulted in recovery of 91.4 percent of the zinc in a Prime Western grade product, and 98 percent of the lead. Hydrometallurgical techniques involved several leaching methods, but the simultaneous extraction of iron, manganese, and copper resulted in contamination of the solution and made the zinc recovery processes too complicated. Agglomeration was done by pelletizing or briquetting the dust for possible use as feed to a zinc smelter.

Jan 1, 1975

The instrumentation specification in the National Academy of Engineering (NAE) report of March, 1970, set forth some rather general guidelines that the seismic surface system should follow. The fact that there was no comparable equipment in existence at that time, and the need to produce a system from presently available equipment, was spelled out in that document. The features that the system should include were listed, and included: • Quick and simple deployment • Portability • Battery-powered operation • All-weather operation • Computational simplicity and speed • High reliability and long shelf-life • Dual service for location and communication • Adaptability to widely varying seismic velocities. topography, and geologic structures • Minimum maintenance • Capability of continuous operation for extended periods, and • Reasonable cost Since that report, there has been a substantial amount of field work addressing the trapped miner detection and location problem carried out by Westinghouse Corporation under contract with the Bureau of Mines. Two complete surface systems have been designed, built, and field tested and substantial documentation has been produced on the mine environment and background noise using these systems. These systems, built from off-the-shelf equipment, have been designed with maximum flexibility in mind in order to explore what con¬figuration a field unit should have.

Jan 1, 1974

By Oliver Bowles

"The introduction into mines, quarries and manufacturing plants of machines and tools operated by compressed air has revolutionized methods of operation to an extent comparable only with that occasioned by the invention of explosives and the utilization of electricity. The use of compressed air in pneumatic tools, in rock drills, and for the operation of pumps and other machinery is well known to most miners and quarrymen, but its application as a substitute for explosives for breaking rock in a few granite quarries has received little publicity.In the region of Lithonia, a few miles from Atlanta, Georgia, is a dome of massive granite used widely for building stone and for paving blocks. The most remarkable structural feature of the granite is the absence of joints and sheeting planes. The term ""joints"" is applied to open fractures that commonly occur in rocks, usually vertical in direction or nearly so, and spaced from a few inches to several feet apart. On the Lithonia granite outcrop, however, one may walk over the bare rock surface for hundreds of feet without finding any indications of a joint, ""Sheeting planes"" are open fractures at various levels, approximately parallel with the rock surface. The presence of such planes when spaced several feet apart greatly facilitates quarrying, and where absent, as at Lithonia, the necessary fractures must be made artificially.The forcing of artificial sheeting planes is accomplished as follows: Two holes of about 3-inch diameter arc drilled close together and to a depth of about 8 feet. Two men work at these holes all summer, and sometimes part of a second summer. A very small charge of black blasting powder, not more than a spoonful, is placed in each hole, tamped with clay, and the charges are fired simultaneously with an electric battery. This starts a small fracture running outward from the bottoms of the holes. There is in most granites one direction of easy splitting known among quarrymen as the ""rift"", and as the rift direction in the Lithonia granite is horizontal the fracture follows a horizontal plane,"

Aug 1, 1920

By A. J. Farstad, R. G. Olsen

The Coal Mine Health and Safety Act of 1969, passed by Congress in the wake of the disaster at Farmington, West Virginia, led to an extensive study by the National Academy of Engineering of the problems involved in coal mine safety. One of the results of this report and subsequent research conducted by the U. S. Bureau of Mines has been the investigation of electromagnetic techniques for the location of trapped miners after a mine emergency. The Westinghouse Georesearch Laboratory has been involved in both the 2 theoretical and field studies relating to this problem. A compact personal beacon transmitter has been developed which can be attached to and powered by a miner's lamp battery. A compatible lightweight loop antenna package has also been developed which can be easily carried on a miner's belt. This antenna can be quickly deployed on the mine tunnel floor. For the purpose of calculating its electromagnetic fields on the earth's surface, the loop can be considered to be a magnetic dipole buried in the earth. (The earth is assumed to be homogeneous and to have a conductivity of s mhos/m.) The surface of the earth is assumed to be uniformily sloping and the transmitter dipole oriented as in Figure 1. The fields on the earth's surface can be computed by using a superposition of the fields of a 4 vertical magnetic dipole3 and of a horizontal magnetic dipole in proportions which depend on the slope of the terrain. In the case of level terrain a null in the horizontal magnetic 5 field occurs on the surface directly above the dipole. This null is designated as the apparent source location and is the criterion by which the source is located. The criterion was tested at two hardrock mines and two coal mines in the fall of 1972. The apparent source locations were compared to actual locations determined by conventional surveying techniques. It was found that due to nonlevel terrain the apparent and actual source locations differed by up to 13 meters. This discrepancy can be resolved by an examination of the fields of a source beneath uniformly sloping terrain. Figure 2 shows the experimental and theoretical results for a

Jan 1, 1973

By B. T. Brady

Results of a study are presented of the effect of low radial reinforcement pressure on the postfailure characteristics of two types of granite, a sandstone, and marble. The low radial reinforcement pressure is applied to the rock surface by a gooch rubber sleeve. The gooch rubber sleeve provides a radial pressure of less than 1 psi pressure to the rock surface. This method of support gives an average strength increase of approximately 8 percent to the fractured rock sample.

Jan 1, 1973

By Douglas D. Reynolds, Tarek Deeb, Qunli Liu

Landmines are a great threat to military vehicles and their occupants. Mine blasts can completely destroy vehicles and kill all the occupants or disable the vehicle and leave the occupants severely injured. Injuries sustained during a landmine blast come from fragmentation that enters the vehicle through a hull breach, hot gasses expanding through the vehicle, or shock created from the extreme pressure of the blast (Lafrance, L.P. 1998). Mitigating the high acceleration experienced by the occupants during survivable mine blasts is the focus of the research being addressed in this paper. Method The objective of the project reported in this paper was to prove the feasibility that pneumatic seat technologies that employ light-weight, foam-filled, inflatable air bladder seats and seat backs can be used to protect the crews of lightweight combat vehicles against the detrimental and injurious effects of mine blasts. This protection includes reducing the shock energy experienced by seated vehicle crews during mine blast initiation and at vehicle slam-down to below potentially injurious levels. Figure 1 shows a schematic representation of the proposed lightweight, foam-filled, inflatable mine blast attenuating seat. It will consist of specially designed interconnected seat and seat back lightweight, foam-filed, air bladders that are supported by a rigid frame. [ ] Results Air gun tests and finite element analyses were conducted to determine the effectiveness of a light-weight, foam-filled, inflatable air bladder seat shock isolation system in isolating a vehicle occupant from the injurious effects of a mine blast. Figures 2 through 5 show analytical and experimental results associated with a 65.8 kg mass resting on an inflatable air bladder that is exposed to a shock input.

Jan 6, 2006

By L. D. Tracy

"Introduction In the course of the investigations by the Bureau of Mines into the various causes of coal-mine explosions, the fact that several gas explosions had occurred during or very soon after a mine was being un-watered, attracted the attention of the Bureau's engineers. The apparent coincidence was so marked that there appears to be an extra hazard present, whenever water, which has been standing against the face of the coal for some time, is suddenly removed either by natural drainage or by mechanical means.Actual Occurrences Case 1. - A typical illustration of this hazard is shown in a gas explosion which occurred in a mine in Central Pennsylvania. Four main entries, 50 feet apart with an average grade of 6 per cent, had been driven with the dip of the coal, and from these mains 7 pairs of entries, at intervals of 800 feet, had been turned at such an angle that their grade was slightly rising. Prom these latter pairs of entries, rooms were turned practically at right angles.The main entries had been driven for 4,500 feet and at the face there was 400 feet of cover. As far as could be observed, the roof was of sandstone and the floor of clay.The coal bed being mined was the Lower Kittanning, which has a thickness of about 4 feet. A typical analysis of the coal in that section is as follows:"

Oct 1, 1924

Occupational illnesses are more difficult to identify than on-the-job injuries. Many illnesses related to occupational exposures may not be diagnosed until years after exposure; by that time, exposed workers may have changed jobs or left the workforce. Other approaches to identifying occupationally related illness are analysis of death certificate data (see chapter 2) and medical examination studies of workers known to have high exposures to hazardous agents. Figures 5-1, 5-3, 5-4, 5-6, 5-8, and 5-10 show, for each commodity, the percent of illness conditions reported to MSHA by nature of condition. Heart attacks that occurred on the job are reported without regard to work-relatedness. Figures 5-2, 5-5, 5-7, 5-9, and 5-11 show rates by year during 1986-1995 for selected conditions. Since there are many limitations on the accuracy of illness reporting, the frequencies and rates shown here should not be considered directly comparable across commodities. Figure 5-12 shows estimates for hearing loss by age among coal miners compared to a nonoccupationally noise-exposed population. These data come from a study by Franks [1996] of a group of audiograms obtained on coal miners by a commercial company. Using the NIOSH definition of hearing impairment, i.e., an average hearing threshold level for both ears that exceeds 25 dB at frequencies of 1,000, 2,000, 3,000 and 4,000 Hz, the figure shows that by age 30, more than 10% of miners suffer hearing impairment; by age 50, 90% of miners have hearing impairment. In contrast, only 10% of the nonoccupationally noise-exposed population suffer hearing impairment at age 51, and 50% of the nonoccupationally exposed population have hearing impairment at age 69. Figure 5-13 shows a similar analysis of commercial audiograms on male metal/nonmetal miners [Franks 1997]. At age 20, approximately 2% have hearing impairment using the NIOSH definition of hearing impairment described above. This increases to 7% at age 30, 25% at age 40, and 49% at age 50. In contrast, only 9% of the nonoccupationally noise-exposed comparison population have hearing impairment at age 50. Franks' analysis showed a different pattern for female metal/nonmetal miners; they developed hearing loss at the same rate as would be expected for a non-noise-exposed female population.

Jan 5, 2000

By A. R. Rule

Research was conducted by the Bureau of Mines to develop a process for utilization of Idaho kyanite. A continuous gravity-flotation separation process was applied successfully to recover kyanite-group minerals from an Idaho ore containing about 21 percent combined kyanite, andalusite, and sillimanite. Dry magnetic separation of the concentrate resulted in a product containing about 90 percent kyanite at a recovery of 63 percent of the kyanite-group minerals in the ore, Alumina and silica analyses were within the range generally accepted for conversion to mullite, and the finished products had a pyrometric cone equivalent of more than 38. A recovered garnet coproduct may be of commercial value.

Jan 1, 1973

By Michael J. Sapko, Samuel P. Harteis, Eric S. Weiss

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) recently conducted full-scale explosion experiments; these experiments evaluated the strength characteristics of various seal designs used for safely isolating worked-out areas in underground coal mines. Large-scale explosion tests were conducted within the multiple entry section of PRL’s Lake Lynn Experimental Mine (LLEM) employing the only currently accepted test method endorsed by the Mine Safety and Health Administration (MSHA) for seal design in American mines. These explosion tests are labor-intensive, expensive to conduct, and can interfere with other critical underground safety and health research programs conducted by NIOSH. Therefore, the PRL has developed an alternative seal evaluation method, based on a hydrostatic pressure loading concept, that can facilitate the in-situ testing of seals in an operating mine. Two chambers within LLEM and one within the Safety Research Coal Mine (SRCM) were used for hydrostatic pressure loading various seal designs. The results from tests in these chambers compare favorably with those from the large-scale explosion tests in the multiple entries. Preliminary size-scaling relationships for predicting the strength of standard seal designs as a function of entry size is also presented. In addition to testing seal designs at the required 20 psi static pressure level, the new facilities also allow for the determination of the seal’s ultimate failure pressure. This new approach shows promise as an alternative evaluation method for improving mine sealing technologies which, in turn, will enhance the safety of the underground personnel.

By Thomas O. Glover

Economic growth in Cameroon was restricted during 1987 owing to a decrease in oil prices during 1986 and the falling value of the U.S. dollar in 1987. The yearly budget reflected a significant drop in revenues and expenditures. Taxes on imports and some exports were increased to raise revenue. The shortage of revenue and the lack of liquidity had restricted the Government's operation and investment programs. External public debt reached an estimated $3.2 billion2 representing 20.8% of the estimated gross domestic product (GDP) of $12.3 billion. The Government operated at an 8.7% deficit in 1987. The GDP growth rate had fallen to 0.6% in 1987 and was projected to remain at that level in 1988. Economic planning was managed through a series of 5-year plans. The country was under the sixth 5-year plan, which would end in 1991. The plan stressed balanced development as one method to achieve the desired results. Sources of revenue for the year included direct and allied taxes (31.2%). customs collections (31.0%), and oil royalties (28.0%). The oil royalties in 1987 represented a larger part of the budget than in 1986. In January 1987, eight African oil exporting countries, including Cameroon, formed the African Petroleum Producers' Association (APPA). The eight countries represented about 80% of the total African oil production of 5.2 million barrels per day in 1987. Cameroon produced approximately 3% of total APPA oil production. Cameroon produced approximately 68.5 million barrels of crude oil in 1987, slightly less than that produced in 1986. Earnings also fell in 1987, not only from falling production, but also from declining oil prices and the fall in value of the U.S. dollar on world markets. Oil had been the main stimulus of Cameroon's growth throughout the past decade, and a key generator of export revenues and financial resources for the economy.

Jan 1, 1989

By S. P. Howell, M. W. Von Bernewitz

"Introduction. The first short—flame explosives were made in the United States during the year 1902, then the mount was 11,300 pounds. In 1902 they were designated ""permissible explosives"", and were required to meet specific tests. By 1912 the total consumption thereof had increased to 24,630,000 pounds, equal to 5 per cent of the total quantity of all kinds of explosives produced in this country; while in 1922 the total was 43,429,000 Pounds, or 10 per cent of the production, and 18 per cent of the explosives used for the mining of coal.Each year the Bureau compiles statistics of explosives, one important object of this being to show the extent to which permissible explosives are replacing other classes of explosives in coal—mining operations, and the influence of such replacement in reducing the number of accidents caused by explosives in this class of mines. The consumption of permissible since 1916 has considerably exceeded the quantity of high explosives (dynamites, etc.) used in coal mines. While the increase in use of permissible is good, the replacement of other explosives therewith is not nearly as good as with be, considering the known general efficacy and safety of permissibles."

Mar 1, 1924

By T. G. Carnahan

The Bureau of Mines conducted laboratory-scale weathering research on a leach residue containing elemental sulfur and mixed metal sulfides. Experiments were performed to determine pH and impurity element concentrations in the effluents as functions of time and to determine the effects on effluent concentrations of mixing the residue with dolomite tailing material. Four 800-day tests were conducted simultaneously. Soluble metal concentrations, especially zinc and copper, were excessive in the effluents from washed and unwashed samples of the residue. Concentrations of up to 20 g/l of Zn and 12 g/l of Cu were obtained. The pH values of the unwashed and washed residue effluents at the completion of the experiments were 2.8 and 1.9, respectively. Sulfuric acid from oxidation of pyrite caused the pH decrease. Mixing unwashed residue with dolomite tailing to maintain a near-neutral pH minimized the heavy metals content in the effluents. The pH in the dolomite tests increased slowly after the first 360 days and attained values of 7.8 and 8.2, respectively, for tailing containing 1 pct leach residue and for tailing devoid of leach residue. Dissolved zinc and copper did not exceed 0.10 g/l of Zn and 0.001 g/l of Cu.

Jan 1, 1982

By John R. M. Hill

The Bureau of Mines performed elastic-plastic, finite-element analyses to investigate the support performance of hydraulic backfill. A mathematical model was developed for two vertically adjacent stopes separated by a sill pillar. An exact duplicate of a working stope was not intended; however, the model did simulate a working stope to the extent that field measurements from an active stope could be used for comparative purposes. Using a predetermined mining sequence, the computer analysis simulated the mining operation as a series of incremental cut-and-fill steps. Computer results included a complete history of stope closure and pillar stresses throughout the mining sequence. With the mining sequence and rock properties held constant, three separate analyses were made using varying backfill properties. These cases included no fill,-low-to-medium-quality fill, and medium-to-high-quality fill. Results of these analyses show decreases in stope closure and pillar stresses as the backfill quality increases, thus reducing the possible occurrence of rock bursts. Predicted stresses within the backfill compare favorably with field measurements. A relationship between maximum stress normal to the stope wall and the ratio of relative fill stiffness to relative rock stiffness was also indicated.

Jan 1, 1974

By P. Delogne, L. Deryck, R. Liegeois

So far as the propagation of electromagnetic waves is concerned, an underground tunnel behaves like a pipe or hollowed waveguide. Waves propagate in this tunnel with a low attenuation only if their frequency is higher than a so-called critical frequency which depends on the shape and mostly on the cross -dimensions of the tunnel and which value is in the neighbourhood of several tenths of MHz. However, when a metallic conductor is stretched along the gallery the electromagnetic characteristics of the latter are considerably modified and the effect of the cut-off frequency disappears; this is due to the fact that the gallery equipped with such a conductor works like a coaxial cable where the conductor serves as the outward conductor and the wall of the gallery as the return conductor. This is the principle of the monofilar waveguide cable which has been perfectly studied by Gabillard. Two mean characteristics of the monofilar mode are as follows: first of all, when the cable is suspended in the middle of the cross section of the gallery, the electromagnetic field occupies all the space between the wire and the walls of the gallery. When the wire is close to the wall, the electromagnetic field tends to become concentrated between the wire and the wall, with the consequence that, with the given monofilar mode power, the aerial of a receiver standing somewhere in the tunnel will capture a weaker and weaker signal. Secondly, owing to the fact that the mode of monofilar propagation uses the ground as return conductor, its power of propagation is considerably diminished; the closer the wire is to the wall the higher the attenuation, for only a very small part of the wall is utilized as return conductor. To cover great distances, everything else being equal, two or more conductors must be placed in the gallery. If the distance between two conductors of a cable is much smaller than the distance between one or other of the conductors and the walls; or again if one of the conductors surrounds the others and forms a screening, two sorts of modes appear: on the one

Jan 1, 1973

By Jeffery L. Kohler, Eric R. Bauer

Prolonged exposure to noise over a period of years generally causes permanent damage to the auditory nerve and/or its sensory components. This irreversible damage, known as noise-induced hearing loss (NIHL), is the most common occupational disease in the United States today. Workers suffering from NIHL have difficulty understanding human speech and hearing other workplace cues. Despite the use of regulations and efforts by government and industry to reduce NIHL, the problem today is as prevalent as it was more - than two decades ago. Recently, the Mine Safety and Health Administration (MSHA) promulgated a new regulation that is designed to reduce NIHL in the mining industry. One of the more significant provisions is the elimination of MSHA's past practice of giving "credit" for the use of personal hearing protection, thereby reestablishing the primacy of engineering and administrative controls. However, there is a knowledge gap that is impeding the development and implementation of engineering and administrative controls. Although significant data exist on the exposure to noise by occupational code, little is known about the noise sources that contribute the most to the worker's dose. This is problematic in a workplace with multiple noise sources and workers who travel among noise sources. Yet without this knowledge, it is difficult to focus control efforts in any practical manner. Thus, it is important to characterize noise sources sufficiently well so that the sources most hazardous to hearing are identified and those conditions of exposure that are most amenable to engineering controls are pinpointed as well. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of noise sources and worker noise exposures in the mining industry to address this deficiency. The initial effort, conducted at a coal preparation plant and results are described in this paper. Preliminary analyses indicate that the noise levels on all floors exceeds 90 dBA in most areas, and that levels as high as 115 dBA were recorded. In addition, the one worker whose responsibility is to monitor the equipment and "house clean" the plant is slightly overexposed, even though he spends only half the shift in the plant. General information on the hearing loss problem in mining, a review of hearing protection use and noise regulations in mining, and other background materials are also presented.