Search Documents

By Charles E. Whieldon

Because of the importance of recovering more oil from known petroleum reserves, increased emphasis has been placed on the application of secondary-recovery methods. It is hoped that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases. Previously published reports3 4 5/ have described the results of water-flooding in Roane, Pleasants, and Wetzel Counties, W. Va. (fig. 1). This report describes the South Penn Oil Co. Yawkey waterflood property, Berea sand, Griffithsville oilfield, Duval District, Lincoln County, W. Va. (fig. 2).

Jan 1, 1961

By Leonard Obert

This report presents evidence indicating that when rock is stress-relieved during the course of mining or in drilling a core, it may be altered or damaged to the extent that the physical properties of the relieved specimen are not the same as those of the in situ rock. Furthermore, this type of damage may result from stress change other than that accompanying stress relief, such as the application of a relatively large compressive stress. In some instances the damage is microscopic, manifesting itself as incipient cracks or the failure of individual crystal bonds. However, if the sample is taken from a high-stress area, macroscopic damage may occur.

Jan 1, 1962

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most, States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the Oklahoma Planning and Resources Board of the Conservation Commission has been authorized to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

By Z. T. Bieniawski, Benjamín Celada

After emphasizing the importance of quantitative rock mass classifications in mining, originally directed to selection of rock support measures, but subsequently to estimates of rock mass properties such as rock mass strength and rock mass modulus of deformation, current attention calls for a classification specifically for rock mass excavability by tunnel boring machines (TBMs), which are used extensively in tunneling as well as in the mining industry. This paper introduces the Rock Mass Excavability (RME) index for predicting excavability of rock masses by TBMs using a quantification of machine performance and rock mass conditions. The RME index is based on five input parameters aimed at relating rock mass behavior and machine characteristics: (1) uniaxial compressive strength of the rock material, (2) drillability/abrasivity, (3) rock mass jointing at mine drift face, (4) standup time of the excavation, and (5) groundwater inflow. Development of the RME index entailed the collection of extensive data from more than 28 km of tunnels and some 400 case records from projects in Spain involving double-shield TBMs. In the process, a number of statistical correlations have been established between RME and such output parameters as degree of machine utilization, advance and penetration rates, thrust and torque of the cutterhead, and the specific energy of excavation. It was found that the RME index provides a particularly significant correlation for predicting the average rate of advance (m/day). In essence, the RME index is a classification system that features interaction of rock mass conditions with boring machine characteristics for use in the early stages of a project. It should be noted that the RME index does not replace the Rock Mass Rating (RMR) or Q-systems as used in mining and tunneling; indeed, one of the RME input parameters, standup time, is determined from the RMR. However, the approach presented introduces a specialized tool relevant to excavating tunnels and drifts. Possible applications to hard-rock mining are explored.

Jan 5, 2007

Significantly increase the amount of fresh air that sweeps the face in front of a continuous mining ma-chine, in order to prevent methane gas buildup. Approach Water sprays are mounted along the sides of a continuous miner and behind the cutter head to help push ventilating air along the required path, and prevent its short circuiting. How It Works A continuous miner is fitted with two sets of water sprays, one of which is used at a time. The set of sprays shown in the diagram, helps move the ventilating air forward along the left side of the miner and across the cutter drum from left to right. That air is then drawn into the exhaust air passageway located along

Jan 1, 1978

By George A. Morgan

The successful expansion of crude oil production begun in late 1977, led to promising development of the nonfuel minerals sector. Although actual production of nonfuel minerals was limited both in variety and in percentage of output on a world scale, the potential for expansion with a rapidly developing infrastructure was significant. The energy base was expanding with construction of two new hydroelectric powerplants in addition to the existing plant near Edea. The Song Loulou plant will have a 240-megawatt capacity, and a hydroelectric plant under construction in the northern part of the country by mainland China will have 72 megawatts of installed capacity. Inflation of between 15% and 20% resulted in a real gross domestic product (GDP) of $2.8 billion2 in fiscal year 1980 (July 31 to June 1), up 6% from that of the previous fiscal year. Petroleum became the leading export item in terms of value, surpassing coffee and cocoa exports. Mineral exports as a whole increased eightfold in value, mainly because of oil sales. Oil exports also caused a reduction in the trade deficit by nearly one-third, and the Government expected its 1980-81 budget to be balanced at $1.17 billion. The Port of Douala accounted for about 8 million tons of cargo, or 93% of total maritime traffic for Cameroon. Expansion plans for the port call for an initial increase to 5 million tons, and a cargo handling capacity of 7.5 million tons in 1985 and 10 million tons by 1990. The Port of Victoria will gain importance with the startup of an oil refinery. The country's third seaport at Kribi was used solely for timber shipments, and capacity at the Port was to triple by 1981. The Government operated its own shipping line with six oceangoing freighters. France was the dominant trading partner, accounting for 25%

Jan 1, 1982

By Sidney Katell

This cost bibliography, covering the period from January through December 1960, is a continuation of the series which began with the publication of Information Circular 7516 in October 1949. It is also the second report in the series to be prepared as a cooperative effort by the Bureau of Mines and the American Association of Cost Engineers. The cooperative agreement between the two groups provides for the publication of an annual bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of petroleum and chemical plants and related facilities, came from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Report of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Week. 6. Coal Age. 7. Coal. Utilization. 8. Cost Engineering. 9. Industrial and Engineering Chemistry. 10. Nucleonics. 11. Oil and Gas Journal. 12. Petroleum Engineering. 13. Petroleum Refiner. 14. World Oil.

Jan 1, 1961

By Robert I. Fujimoto

The work described was conducted to develop standards for the application of wire rope clips on wire rope. These standards include optimum number of clips and clip nut torques for wire rope sizes 1/4 through 2-1/4 inches, when used for forming an eye attachment in wire rope. Wire rope test specimens with clip attachments were load tested on tensile testing machines to determine an effective combination of clip nut torques and number of clips for each size of wire rope to develop efficiencies above 90 percent of the catalog ultimate rope strength.

Jan 1, 1973

By A. R. Taylor

In recent years, thermodynamic data have been used to a greater degree than ever by the chemical and metallurgical engineer as a means of predicting and controlling chemical reactions. To satisfy the spiraling demand for basic physical data needed for the calculations, the Bureau of Mines is studying the heat capacities of a variety of chemical compounds at high and low temperatures. This paper is one of a series presenting such data. The heat capacities of two alkaline earth compounds, strontium bromide and strontium nitrate, were measured in a temperature range of 60° to 300° K. in an adiabatic calorimeter and at temperatures of 300° to about 1,200° K. in a Bunsen ice calorimeter. The construction and operation of the calorimeters are discussed in other reports.3 4 The heat-capacity data presented in this report were extrapolated to 0° K., and smooth values of heat capacity, entropy, enthalpy function, and free-energy function were calculated and tabulated at even 10-degree intervals. The enthalpy data were fitted with algebraic equations by applying the method of least squares; calculations a£ heat-capacity values, entropy, enthalpy function, and free-energy function were made at even 50-degree intervals. The heat and entropy of fusion of strontium bromide were calculated from the enthalpy measurements.

Jan 1, 1962

VOLUME II Volume II, in conjunction with Volume I, is a general guide to the selection of cost-effective methods of site data acquisition in all geologic environmental, and socio-political circumstances. The judgement of a generalist or trained specialist must be relied upon in the final analysis to design the optimum program for a specific site.

Jan 1, 1976

By Ned Baker

Details are given of a Hydride Fuel System to provide 5 kg of HZ to fuel a Caterpillar 3304 engine previously modified to operate on hydrogen fuel and intended to power an underground mining vehicle. The Fuel System was installed onto the engine and the Engine/Fuel System tested under cold start conditions and a full range of engine loads and speeds. Refueling tests were also performed. The fuel system tested will support full engine power and allow delivery of at least 3/4-power on a continuous basis, from cold start conditions.

Jan 1, 1983

By Victor R. Spironello

The Bureau of Mines has conducted studies of the slags related to ferrous technology to evaluate experimentally acceptable substitutes for the auxiliary flux, mineral fluorspar, in steelmaking operations. Comparative heats were made in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF) to evaluate a waste material known as "used potlining." Used pot lining is recovered from alumina reduction cells after its useful life and contains significant levels of fluorine and sodium in various compounds. This material in both lump and pelletized form provided adequately fluid slags, based on observations made during BOF operation. No adverse effects were found on furnace performance, metal and slag chemsitry, the strength of the steel produced, or the environment. Fluorine recovery in the slag was about the same as that obtained when using fluorspar, as were the losses to the scrubber water and solids. No difference was observed in furnace-refractory attack, as determined by the level of magnesia in the slag. The sodium recovered in the slag apparently also contributed to fluidity, since the fluorine input was at about two-thirds that of the fluorspar. Used potlining was determined experimentally to be a satisfactory substitute for fluorspar in basic oxygen steelmaking.

Jan 1, 1982

By Edward A. Barrett

The ability to recognize visual cues commonly associated with roof and rib hazards is fundamental to the prevention of groundfall accidents. The perceptual skills that miners possess to visually search and assess hazardous ground conditions differ considerably. This U.S. Bureau of Mines report summarizes recent investigations on the use of stereoscopic (3-D) slides as a training aid for improving the ability of miners to recognize the various geologic and mining-induced irregularities that cause ground-falls. The feasibility of using 3-D slides for training and their effectiveness for representing roof and rib hazard conditions are discussed. Information is presented on equipment and procedures for creating a 3-D slide program that can be updated by mine trainers. Recommendations are made on selection of 3-D equipment and on the use of 3-D slides for training miners to recognize roof and rib hazards.

Jan 1, 1988

By Felipe Calizaya

This study describes the principles involved in the design of a booster fan installation, the basic requirements, and the provisions needed to guarantee a safe operation of the unit. It also describes how a booster fan should be selected and what measures should be taken so that events such as uncontrolled recirculation of air in a mine can be avoided. A computer program called MFSELECT is presented to assist the ventilation engineer in the design process a For a given mine ventilation network, the program determines the duties of fans and regulators that will fulfill the airflow requirements of a mine and minimize the total power consumption. The application of the program is illustrated by the detailed solution of a sample problem. A Case Study based on the Jim Walter Resources' No. 7 Mine is utilized to describe the basic requirements for the design and operation of booster fans, and illustrate their potential benefits in mine ventilation. Finally, the study discusses a process control system designed to evaluate the safety conditions in the mine and report on the status of both surface fans and underground booster fans.

Jan 1, 1990

By B. W. Gandrud

The upper part of the Alabama deposits of crystalline graphite consists of an oxidized ore derived from, the underlying unoxidized ore through prolonged weathering. The degree of oxidation in different sections and at different depths within the bed is nut. uniform. The original ore is hard and blue-gray; the weathered product is soft and brown and is the only part that has been mined to any extent. Samples of both oxidized and unoxidized ores were obtained from two of the large graphite deposits of Clay County. Three additional samples of oxidized ore were obtained from different portions of a third property in the same region. In this report, ores 1 to 5 are of oxidized material and ores 6 and 7 of unoxidized.

Jan 1, 1934

By J. H. East

"INTRODUCTION Diesel locomotives have been used successfully in underground mines of Europe for 18 years, and much has been written on the technical details of the design of these machines and the safeguards provided by the manufacturers. The actual conditions under which' the Diesel locomotives are used have not been publicized as well and consequently are not well-known. In 1945 the writer observed numerous Diesel locomotives working underground in coal and metal mines of several European countries and was favorably impressed with the practical approach to the safe use of this- type of equipment.Recent statistics showing the number of Diesel locomotives in use are not available now because of the World War, but the extent to which this type of mine locomotive was used immediately before the war is indicated by table 1, which classifies the number of locomotives used in several countries according to the type of power, such as compressed air, Diesel, and electric.Mining conditions observed by the writer in the European countries are very different from those in most coal-mining districts of the United States. The surface plants are larger and are permanently constructed of brick or concrete; numerous coal beds are worked through one shaft; the crosscut rock tunnels or levels, driven to intersect the coal beds, are lined with brick or concrete blocks where needed instead of timber; the coal beds dip more steeply and are not as thick as in most fields of the United States."

Sep 1, 1946

By Virgil A. Marple

It was the purpose of this contract to conduct research in several different areas of instrumentation used to determine the quantity of respirable dust in the mining atmosphere. One area of research was in evaluation of instruments including several respirable dust monitors, several types of photometers, and a QCM cascade impactor. An instrument evaluation chamber was developed to aid in evaluating the instruments in a dust atmosphere. Another area of research was investigations into new instrumentation concepts, such as a virtual impactor/photometer instrument, a new optical device which can be used as either an optical particle counter or photometer, a new personal respirable sampler, which employs an impactor instead of a cyclone as a preclassifier, and the development of a new cascade impactor, which deposits the particles uniformly on the impaction plate. Another area of research included the use of many of these instruments in two field studies, including a silica sand plant and a tungsten mine.

Jan 1, 1981

By Robert L. Virta

This U.S. Bureau of Mines paper discusses the structure of the talc industry, talc production, processing of talc ore, applications and demand for talc, and the outlook for the talc industry.

Jan 1, 1989

This study estimates costs of producing bituminous coal and lignite by strip-mining methods in 12 hypothetical mines. Basic costs are developed by geographic area, rank of coal, and output capacity. Seam thickness and depth and type of overburden are considered typical for the area in which the hypothetical mine would be located. The cost analyses are based on the use of new equipment, the prevailing union wage scales, and the payment of all miscellaneous costs including royalties, contributions to the miners' welfare fund, and license and permit fees. All model mines are considered to have a life span of 20 years. Capital costs of bituminous strip mines with a capacity of 1 million tons per year range from $12.7 million in the Appalachian region to $16.0 million in the Interior province. The corresponding selling price, assuming a discounted cash flow return of 12 percent on investment, is $5.40 and $6.95 per ton, respectively. For bituminous coal strip mines producing 3 million tons annually, a capital investment of $24.9 million will render a selling price of, $3.46 per ton in the Interior province, whereas a similar mine in the Appalachian region requires a capital investment of $28.0 million to produce coal selling for $4.01 per ton. Subbituminous strip mines of 5 million tons of output per year range in capital costs from $28.7 million in the Southwest to $13.9 million in Wyoming and Montana. Coal produced in the Southwest would sell for $3.03 per ton, while coal from Wyoming and Montana would sell for $1.83 and $1.64 per ton, respectively. The capital costs for the strip mining of lignite range from $6.4 million for an output capacity of 1 million tons annually to $20.7 million for an annual capacity of 5 million tons. The corresponding selling prices of $3.01 and $2.12 per ton, respectively, Indicate the advantages of a large-capacity strip mine.

Jan 1, 1972

By K. E. Robinson

This study is the extension of an investigation of reclamation of floodplain areas in the Coeur d'Alene Mining District, Idaho, that are unuseable in their natural condition, by construction of landfills with mill tailings. The study develops a valley-wide tailings disposal plan to utilize 20 potential landfill sites on floodplain areas and presents measures for reclaiming the sites for subsequent productive use. Field and laboratory testing on a test section and two abandoned impoundments support the use of hydraulically deposited tailings for landfill construction. Hydrological testing has shown that controlled discharge from tailings impoundments results in contaminant levels in the discharge below regulated standards. Additional testing indicated that compacted soil liners and pond management provide adequate contaminant abatement where acid-generating tailings are encountered. Mechanical compaction, including surcharge loading, upgrades foundation support capacity so that construction on the surface of tailings deposits is feasible. On completion of the testing program, the test sections were abandoned and rehabilitated. Details concerning potential landfill sites have been refined. At recent production rates, the 20 sites would result in 680 acres of reclaimed land, while providing a minimum of 40 years of tailings storage capacity. A general design has been developed for the retention dikes. Aspects of embankment stability, including liquefaction are discussed, and are shown to provide an adequate factor of safety under the anticipated range of operating conditions.

Jan 1, 1983